IBM DDYS-T18350N not seen in solaris 9

I have installed Solaris 9 on an old Sparcstation 20. I 've added 2 external SCSI disks IBM DDYS-T18350N . The probe-scsi-all command see the disks:
ok probe-scsi-all
/iommu@f,e0000000/sbus@f,e0001000/dma@0,81000/esp@0,80000
/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000
Target 1
Unit 0 Disk IBM DPES31080SUN1.05S80B9527102358
0695 00011684G9001
D60886
Target 2
Unit 0 Disk IBM DDYS-T18350N S96HDYLV0383
(C) Copyright IBM Corp.
1999. All rights reserved.
Target 3
Unit 0 Disk QUANTUM FB1080J SUN1.05630E9607099763
SUN MICROSYSTEMS
Target 5
Unit 0 Disk IBM DDYS-T18350N S96H5EM35495
(C) Copyright IBM Corp.
1999. All rights reserved.
Target 6
Unit 0 Removable Read Only device TOSHIBA XM-4101TASUNSLCD049402/18/94
When I type the format command I don't see the disks:
# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t1d0 <SUN1.05 cyl 2036 alt 2 hd 14 sec 72>
/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000/sd@1,0
1. c0t3d0 <SUN1.05 cyl 2036 alt 2 hd 14 sec 72>
/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000/sd@3,0
Thanks for your help.
Regards,
Laurent

I've already try the devfsadm cmd but nothing change.
Tx

Similar Messages

  • Second IDE controller not seen, Blade 150

    On our Blade 150, on the first IDE bus I have a hard drive and a DVD recorder. On the second IDE bus I have another hard drive. The second bus is not seen at all. If I do a stop-a, probe-scsi-all the drive on the second controller is not seen. If I swap the two hard drives I get the same results; drives on the first bus are seen, drives on the second bus are not seen. I have also tried a new cable. Do I need to enable the second IDE controller somehow? Am I overlooking something? My goal is to make this a multi-boot machine and use an alias to choose which drive to boot from.

    Thank you for the tip, I gave this a shot. I took all the defaults up to the point where it asked if I wanted to rebuild the path_to_inst file, where I answered yes. Then it asked for the physical name of the root device, I took the default which looked correct. Then it gave me the same error as before, "/dev/dsk/c0t2d0s6 or /usr, no such file or directory" and the boot failed. I then rebooted again and it cannot find the path_to_inst file so aparently it did not get far enough to save the new file.
    Just to clarify what I believe the problem is, here is my layout:
    c0t0d0sX --> Solaris 9 install, boots and runs great, c0t2d0sX listed under both /dev/dsk and /dev/rdsk, c0t2d0sX will mount just fine when running Solaris 9 so the disk looks OK
    c0t2d0sX --> Solaris 8 install, OS was installed when disk was in c0t0d0 location then the disk was moved to c0t2d0 (first disk, second IDE bus), now has problems booting, c0t2d0sX not listed under /dev/dsk or /dev/rdsk on this disk and I think this is the problem.

  • Ipod not seen by windows or itunes

    Hello, I'm totally frustrated and have been searching for hours. Please someone help.
    - Nano 8 gb
    - Windows xp
    Neither Windows (my computer) nor Itunes sees my ipod. Ipod is working fine: did the menu/select thing, cable is good.
    When I plug the ipod in the usb port I hear a bleep and I get a message bottom right "new hardware found ipod"and the icon is a usb cable. Ipod is not in My computer window. Ipod is not seen by Itunes
    Tried Device Manager/I see Ipod with a ? Yellow. If i right click on it and do update driver the ms computer management system crashes and sends error report.
    I tried dowloading the USB driver and placing it in the directory, but I got stuck because there is no windows/inf directory. I tried to update the usb driver with the same ms crash.
    I'm completely frustrated, please can someone help me.

    I was having the same problem the other day. I'm not sure what it was but I think it has something to do with the i tunes and i pod 1.2 update.
    What I did was:
    1. Uninstall i tunes
    2. Restart my computer
    3. pluged my ipod in a slow usb line
    4. waited until my pc recognized it in there. It took a little while.
    5. re installed i tunes from apple.com
    6. waited until i tunes recognized my ipod
    7. updated my i pod with my library it took a long time because i was in the slow usb plug.
    8. re plugged my ipod into a 2.0 usb line
    9. i tunes recognized it.
    10. I then updated my ipod to the new 1.2 version
    11. The problem started happening again
    12 I repeated what I did before and now it is working.
    It was very frustrating! I hope it works for you.1

  • 5th Gen IPOD - Won't Sync and Not Seen by Windows

    Help!!!
    Tried the 5 R's. I have the IPOD in Disk Mode but whilst it will happily charge, it still is not seen by ITunes or Windows Explorer (though is visible inDisk Defragmenter). I have already un-installed and re-installed ITunes etc.
    Prior to putting it into Disk Mode the IPOD still had my library on it and owuld happily work.

    Have you had a chance to look at these troubleshooting pages? They may be of some help:
    iPod missing in My Computer and in iTunes
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    If you are using a laptop, this page might help: iPod not recognized when connected to Windows laptop over USB

  • IPod touch: Seen by XP, not seen on OSX.

    Strange one.
    1st Gen ipod Touch with latest software(think its 3.3), latest version of itunes.
    Its seen and works perfect with Windows XP.
    I plug it into my Mac Book Pro, running Lion and its not seen. nothing happens wihen i plug it in.
    I have reset, restored and wiped the ipod from the device itself and its still not seen.
    I also tried it on a Win 7 machine and its NOT seen either.
    Is this something crazy to do with 32bit architecture. Its seen on Win XP which is 32 but not by  64bit Lion and Win 7.
    Any suggestions?

    Have a Look Here
    Device Not Recognised
    For PC
    http://support.apple.com/kb/TS1538
    For Mac
    http://support.apple.com/kb/ts1591

  • HT4356 My iPad does not find the printer. I have tried the HP app and it works, but in any other app the printer is not seen. How do I get this printer visible to the iPad. All my other network computers find and print with out a problem.

    My iPad does not find the printer. I have tried the HP app and it works, but in any other app the printer is not seen. How do I get this printer visible to the iPad. All my other network computers find and print with out a problem.

    hi
    could you tell us what the other app is please

  • Attachments and history of my emails are not seen by Windows users

    attachments and history of my emails are not seen by Windows users

    Just guessing at what you mean, try this:
    In Mail, while composing a message, go to Mail's menu and click:
    Edit > Attachments > Always send Windows-friendly attachments

  • In my iPad mini some apps are not seen (voice recorder, calculator, compass etc)

    in my iPad mini some apps are not seen (voice recorder, calculator, compass etc)er

    Those apps aren't included in iOS on iPads
    iPad Mini built-in apps : http://www.apple.com/ipad-mini/built-in-apps/
    iPad manual (which has a chapter on each of the built-in apps) : http://support.apple.com/manuals/ipad/

  • Why keyboard and mouse right click not working in Solaris and Linux?

    Hi all,
    I have two problems:
    1) I am working on AWT/Swing application and its working fine in window enviornment,but while running on solaris and linux mouse right-click option window not poping up.
    2) Ctrl+c,Ctrl+v,Home and End keyboard key are not working in solaris and linux OS for same application.
    Pls provide me some solution for these problem.
    -Dinesh

    Hi Nik,
    Thanks for reply. I found some solution for the above problem.
    For mouse right click there was problem in my source code.I have not implemented the mousePressed() method
    In case of keyboard Home, End and arrow key working fine after exporting AWTUSE_TYPE4_PATCH=false; in solaris and linux
    But still Ctrl-c and Ctrl-v not working.
    I am using JDK1.5.0_07+Eclipse IDE 3.1
    -Dinesh

  • Data of measure is not seen in  webi report when drill is disabled

    Hi
    i have created a hierarchy in universe on which i drill down in webi reports
    the problem is that  i have drilled my report till the last level and saved it
    the object  on which im drilling  is set as a section in the report
    so i have added a measure in the table under that section
    now the measure has different value at different level of drillings
    i.e for the last level of the drill i use one measure and after that as i drill up i use different  measure
    for all other level of drilling
    every thing is working fine but the problem  is
    when i open report in view mode
    the measure data is not seen
    only when i enable drill the measure data is seen
    i have done something like thi
    i have used drillfilters in webi reports for checking which level we are in drill mode so as to display the measure value based on drill level

    Seems like DrillFilters needs the drillmode to work fine..
    why don't save the report with the drill button enabled?

  • After upgrading to Mountain lion the hyperlink button is not seen in Preview.  Anyone knows ho to get it back?

    After upgrading to Mountain lion the hyperlink button is not seen in Preview.  Anyone knows ho to get it back?

    Augend wrote:
    After upgrading to Mountain lion the hyperlink button is not seen in Preview.  Anyone knows ho to get it back?
    There have been a few threads about this.  The feature seems to have gone missing in Mountain Lion even though the Help for Preview still mentions it.
    I've filed a bug report on it.
    Matt

  • The salesperson for my iphone 4 said on Christmas morning we could go to our online account, select my number, select to change my SIM card, and enter the ICCID number so that I'd be able to use my iphone 4 today. I have not seen any such steps. Help?

    The salesperson for my iphone 4 said on Christmas morning we could go to our online account, select my number, select to change my SIM card, and enter the ICCID number so that I'd be able to use my iphone 4 today instead of my old phone (not an iphone). I have not seen any such steps. Help?

    I suspect the salesperson that told you that meant your online account with your carrier...have you tried logging into your carrier account online? To do this will require the sim number on your sim card, as well as the phone's IMEI number...you get the sim number off the sim card & the IMEI number, for the phone, is printed on the box.

  • I have migrated a user's mysite in sharepoint 2013 from one domain to another.The issue is that old activtiy data i.e newsfeed data is not seen

    For eg :
    I had a user called domain1\user1 whose mysite was created as http://my/personal/user1.
    Now this user moves to another domain say domain2\user1.Since mysite is already present no new mysite will be created.
    Move-SPUser –Identity "domain1\user1" –NewAlias "domain2\user1"After executing the above query,user is migrated and is able to login to the mysite.But the newsfeed data is not seen.I can see it in the microfeed list but not in the newsfeed page.All other data like documents ,tags,people etc is present
    harsh damania

    it should move all the profile data alonwith, i would check the ULS logs for any clue.
    also make sure following timer jobs ran successfully
    User Profile service application name - User Profile to SharePoint Quick Synchronization
    User Profile service application name - Feed Cache Repopulation
    User Profile service application name - Activity Feed Job
    Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

  • I like and use Top Sites but it has become unsuable with this constant blacking out and reloading the thumbnails.  My MBP has not seen a problem at all.   I have been searching every other day for over a month trying to find a fix in Windows Safari with n

    I like and use Top Sites but it has become unsuable with this constant blacking out and reloading the thumbnails.  My MBP has not seen a problem at all.
    I have been searching every other day for over a month trying to find a fix in Windows Safari with no joy.  I want to resolve, not switch browsers. Please offer up a solution that only refreshes the Top Site thumbnails once a day or as some controlable interval.  Started about two versions ago, now on ver 5.1.5. Windows 7 64bit.
    Safari 5.1.5 for Win64 bit, Windows 7!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    I think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
    the funny behaviour of the trackpad/cursor still persists. any suggestion???
    thanks again

  • Cd drive on my laptop not seen as a device. Can refresh itunes and device appears but get unknown sync error 13019 when transferring cd's to my nano.  The cd's appear on the nano when it's connected to itunes but aren't there when I disconnect?

    cd drive on my laptop not seen as a device. Can refresh itunes and device appears but get unknown sync error 13019 when transferring cd's to my nano.  The cd's appear on the nano when it's connected to itunes but aren't there when I disconnect?

    Satellite L675-S7113 Specifications (PSK3AU-07C02S)
    Satellite L675-S7113 Support Page
    rwls wrote:...since I got it 3 years ago I've been unable to burn an audio CD from ITunes or Windows media although it worked once after the computer had been shut off for awhile..and didn't find the problem until after my warranty had expired...
    From your statements above, it sounds like you never tried to burn a CD for at least the first year that you owned the laptop, as it had a one year warranty on it. While you might have used it frequently to install software,  play DVDs, Blu-Ray disks, etc, that's unclear from your statements. Nonetheless, it might just be dirty-dusty. So, before deleting-uninstalling any software, and given they're cheap, try a CD-DVD Cleaner Disk first and see if that resolves your problems.
    Let us know what happens. Good luck.
    Mike

Maybe you are looking for