IBM MCS Servers Enable Restore on Insertion

We have a MCS7845I3-K9-CMC2 and I'm trying to figure out how to enable the RAID array to rebuild when you replace a drive.  Currently you have to go into the MegaRAID config tool and manually rebuild it which is a PITA.  Geoff I'm looking at you to come through with an answer, please try to keep it under 5 paragraphs.
david

Good one, David.
But as you might guess from my login name, I'm only experienced with HP servers,
Regards,
Geoff

Similar Messages

  • Auto Restart in IBM MCS Servers.

    Hi,
    we are using the below servers in implementing the Cisco Contact Center.
    how can we check whether these servers supports auto restart in temporary power failure. For instance, the servers should be able to automatically restart following a power failure.
    MCS-7845-I3-CCE1
    MCS-7825-I4-CCX1
    MCS7825I4-K9-CMC2
    MCS7825I4-K9-UCB1
    Also, do we need any separate software to support this feature.
    Regards,
    NS...

    Hi, NS.
    I'm sorry to see you were not able to find the information or assistance you were looking for here in the Contact Center community forum.
    May I suggest that you re-post your question on the IP Telephony forum?  General MCS hardware questions are often posted and answered there.
    Thank you, and good luck.
    -Paulo

  • CCM IBM MCS-7845 Server RAID Configuration

    We have IBM MCS-7845 server and need to mirror the hard drive for disaster recovery.
    We have two array configured and each array has two HDs.
    Can we pull the HD from slot 0 and replace with the new one while server is running.
    What is the procedure of doing that ?
    Thanks

    No,
    You hava a change to corrupt your system, it has open files and the system might be writing while you pull.
    a. Turn off the server
    b. pull disks 0 & 2
    c. power on
    d. Insert a replacement drive into Slot 0.
    e. Press F5.
    f. Choose Start > Programs > ServeRaid Manager > ServeRaid Manager. You can view the progression of the drive mirroring.
    http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/3_3/install/upgrade/upgra333.htm#54464

  • IBM MCS Server RUnning Unity with NIC Teaming

    All,
    has anyone ever run NIC teaming on and IBM MCS Server with Unity before? At question is the fact that many severs create a virtual MAC address that is different from either of the actual MACs when you team NICs. If this is the case on the IBM Servers then we may need to request an updated license. The servers are branded as Cisco MCS-7835-I1
    units.
    Thanks in advance. All replies rated!

    Hi
    According to this doc: http://www.cisco.com/en/US/prod/collateral/voicesw/ps6790/ps5748/ps378/product_solution_overview0900aecd80091615.html
    The 7825-I4 is an IBM IBM x3250-M2. You can use that model number to search the IBM drivers page for the things you need:
    http://www-933.ibm.com/support/fixcentral/systemx/selectFixes
    I think the NIC teaming comes with the Network Drivers.
    Regards
    Aaron
    Please rate helpful posts...

  • I need to confirm this: Can the UCS servers be used instead of MCS servers for Voice applications?

    hello friends,
    The question is the same as in another discussion,  so I ask you to help me confirm it, the UCS servers Can be used instead of MCS  servers in Cisco `s Applications like: CUCM, Cisco Unified Presence, Meeting  Place, etc?
    I could show someone a link that you mention it  and show its own applications?
    Regards,

    need upgrade ccm version  to 8.0

  • Oracle 8i on IBM Netfinity Servers

    Hi there!
    Anyone can share an experience installing Oracle 8i under Red Hat Linux on IBM Netfinity servers? Did you needed to patch the kernel, tunnung SGA, etc? What were the maximum parameters you were able to set for Oracle and the linux kernel? MTS worked well?
    I am having trouble configuring more than a few MB for the SGA, and I really need it. My database has ver big batch processes and thousand of on-line users. We are worried we had chooses the wrong hardware or OS for our database.
    null

    Could you please tell me about your configuration? We have a NetFinity 7000-86801SY with 4Gb RAM. When we apply patchs for the Linux kernel so it supports more RAM I cannot start Oracle.
    Besides when we use standard RHL 6.1 kernel, maing the SGA bigger (about 300Mb) the instance runs without errors but incredbly slow and eating up all CPU.
    null

  • How I disable my textbox at view time and Enable only when insert or edit t

    hi master
    Sir i have master detail form and i am not use toolbar i am usint my button add/edit/view/next/last and other
    sir my requirement is all textbox disable at view time enable ony edit or inserting time
    how I disable my textbox at view time and Enable only when insert or edit time.
    i use this
    if :system.form_status='change' then
    if :system.form_status='insert' then
    if :system.form_status='execute query' then
    but not right work
    please give my idea where i use what statment
    send me sample
    Aamir

    Aamir,
    Set the text item's Enabled property to False at design time. Then, using SET_ITEM_PROPERTY (see Forms Help), set to Enabled in the relevent part of the code on the WHEN-BUTTON-PRESSED triggers on your Insert and Update buttons. Similarly, disable on your Save button once the cnahges are saved etc.

  • How can i re-enable/restore a disabled iPad and keep the data without using a laptop or iCloud

    Hello,
    Is there a way to re-enable a disabled iPad and maintain the data taking into consideration that no iCloud backup was made and the computer it was last synced with was not available? any idea?

    No, sorry.  Without a backup in iCloud or iTunes, you will have to set it up as if new and anything on it will be lost now.
    You can always re-download purchased apps and content (other than audiobooks) once it is restored, from the respective iTunes or App stores.

  • Need to enable html snippet insertion in CS4

    The insert html snippet option is disabled on my insert menu and I need to enable it. Please help. Thanks.

    Hi,
         The website administrator has to enable the permission for inserting HTML snippet, for your role, for the Insert HTML Snippet menu to be enabled. If you are the website administrator, you can follow these steps to enable the Insert HTML snippet menu item:-
    Launch Contribute and select Edit -> Administer Websites, and select your website.
    The Administration dialog for your website will be shown.
    Select a role (for ex, Administrator), and click Edit Role Settings button.
    The Edit Role Settings dialog will be shown.
    In this dialog, select Editing from the left panel, and check the check box for 'Allow HTML Snippet Insertion'.
    For more information, click the following link http://blogs.adobe.com/contribute/2009/06/are_you_a_power_user_try_using.html
    Hope this helps. Cheers.

  • Oracle 11gR1 RAC in IBM p servers, VIOS or NOT

    Hi,
    Before IBM VIOS was certified by Oracle RAC last year, I always use two HBA ports and two NIC card ports on each node for redundancy purpose in the RAC implementation in IBM p series servers. I would like to hear other expert's opinion whether VIOS should be considered in the Oracle RAC.
    Here are the pros and cons that I could think of for whether or not using VIOS in RAC:
    Use dedicated HBA and NIC:
    pros: the storage I/O and network throughput are guaranteed and predictable.
    cons: additional cost, the LPAR can not be dynamically moved to another frame if needed (since HBA and NIC are attached to the LPAR)
    Use VIOS:
    pros: I/O Virtualization.
    cons: the LPAR can be dynamically moved to anther frame if needed. RAC node I/O may be impacted by other LPARs that use same device.
    You comments or suggestions are highly appreciated.
    Thanks,
    Limin.

    Hi,
    Before IBM VIOS was certified by Oracle RAC last year, I always use two HBA ports and two NIC card ports on each node for redundancy purpose in the RAC implementation in IBM p series servers. I would like to hear other expert's opinion whether VIOS should be considered in the Oracle RAC.
    Here are the pros and cons that I could think of for whether or not using VIOS in RAC:
    Use dedicated HBA and NIC:
    pros: the storage I/O and network throughput are guaranteed and predictable.
    cons: additional cost, the LPAR can not be dynamically moved to another frame if needed (since HBA and NIC are attached to the LPAR)
    Use VIOS:
    pros: I/O Virtualization.
    cons: the LPAR can be dynamically moved to anther frame if needed. RAC node I/O may be impacted by other LPARs that use same device.
    You comments or suggestions are highly appreciated.
    Thanks,
    Limin.

  • 'Secondary Logon' service for Windows servers - enable or not?

    Hi,
    Since have only one windows server working as 'TS server' to remote employes on our network and another 04 (one for SQL, another for Exchange, another for File and another for DHCP/DNS), can we disable that service on all servers except TS server or we can
    disable it on all??
    >>> There is some services that depends on it?
    interesting article:
    http://tech-wonders.blogspot.com.br/2009/08/disable-secondary-logon-service-to.html
    useful links:
    http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/sys_srv_secondary_logon.mspx?mfr=true
    http://www.blackviper.com/windows-services/secondary-logon/

    Windows Secondary Logon allows administrators to log on with a non-administrator account to perform administrative tasks without logging off by using Run as option. 
    Enabling/Disabling depends from one organization to another.
    Arnav Sharma | Facebook |
    Twitter Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members
    reading the thread.

  • Installation of CCM 6.1.2 on IBM MCS-7825-I4 V03 'drivers not found'

    Hi all,
    Wondering if anyone can help me resolving the issues that I'm experiencing while performing the installation of CCM BE 6.1.2 on the MCS server, receives an error that 'driver not found'.
    the media iso image of ccm has no issues, thinking firmware is not compatible so have upgraded firmware twice to FWUCD-221-1 and FWUCD-3-6-5-1 while installing ccm still the same error.
    Collected DSA and TAC has provided to IBM, they think no issues with hardware and CD/DVD drive may not be compatible, not convinced with their findings, so decided to post the case in this form, as I know real guru's are here :)
    Much apprecited.

    Hello, I ran into the same thing this evening but had no idea about this bug! I wish I was subscribed to the right email group!
    But I went to that site you mention, got FWUCD-2.4.1-I.iso (550MB) from Cisco's software page, burned it and ran it on the server in bootup.
    It updated the BIOS to 1.45 and also the Broadcom NIC cards.
    Everything is up and dandy on our Unity Connexion 1.2, soon to be Version 7.x.

  • Data Servers Enabled Servers not visible

    Hi,
    We seem to be having a problem with xMII at the moment.  Enabled servers within Data Servers are not visible.  The windows is completely blank.  After unchecking Show Only Enabled Server we get the following error as below and no connectors are visible.  The version of xMII being used is 11.5.  Any pointers on how to solve this.
    Thanks,
    Vanshi
    Error. The server encountered an unexpected condition which prevented it from fulfilling the request.
    java.lang.NullPointerException
    at pagecompile._Admin._Server_xjsp._jspService(_Server_xjsp.java:138)
    at com.newatlanta.servletexec.JspHttpJspPage.service(JspHttpJspPage.java:41)
    at com.newatlanta.servletexec.JspServlet.service(JspServlet.java:1036)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:856)
    at com.newatlanta.servletexec.SERequestDispatcher.forwardServlet(SERequestDispatcher.java:638)
    at com.newatlanta.servletexec.SERequestDispatcher.forward(SERequestDispatcher.java:236)
    at com.newatlanta.servletexec.SERequestDispatcher.internalForward(SERequestDispatcher.java:283)
    at com.newatlanta.servletexec.SEFilterChain.doFilter(SEFilterChain.java:96)
    at com.lighthammer.cms.system.CMSFilter.doFilter(Unknown Source)
    at com.newatlanta.servletexec.SEFilterChain.doFilter(SEFilterChain.java:60)
    at com.newatlanta.servletexec.ApplicationInfo.filterApplRequest(ApplicationInfo.java:2159)
    at com.newatlanta.servletexec.ApplicationInfo.processApplRequest(ApplicationInfo.java:1823)
    at com.newatlanta.servletexec.ServerHostInfo.processApplRequest(ServerHostInfo.java:937)
    at com.newatlanta.servletexec.ServletExec.ProcessRequest(ServletExec.java:1091)
    at com.newatlanta.servletexec.ServletExec.ProcessRequest(ServletExec.java:973)
    at com.newatlanta.servletexec.ServletExecService.processServletRequest(ServletExecService.java:167)
    at com.newatlanta.servletexec.ServletExecService.Run(ServletExecService.java:204)
    at com.newatlanta.servletexec.HttpServerRequest.run(HttpServerRequest.java:487)

    Give these URL's a try:
    /Lighthammer/Illuminator?Service=SystemInfo&Mode=ServerList
    /Lighthammer/Illuminator?Service=SystemInfo&Mode=ServerList&Mask=Disabled
    They should essentially give you the list of active and disabled data servers (much like the jsp page is trying to do)
    It is possible you managed to get an invalid name in the system and that's causing the error.
    You could also look carefully into the Server.xml file in the Conf directory.
    A ServletExec restart will also cause the system to re-read the file and log out trace information about the data server in the cms.log file (you'll see Loading Servers... and then you should see them one at a time).

  • Turning off find my phone to enable restore....password not accepted

    Hi
    My iphone5 has lost its phone connection and the carrier bar has disappeared from settings. I am being told to back up and restore from itunes but to do this I need to turn off Find My Phone and it won't do this (wont accept my password, which I have checked several times is the correct one). Help! Thanks

    Do it on a computer: http://support.apple.com/kb/PH2702

  • Install PI 7.1 on iSeries

    Hi ALL
    I'm currently trying to install PI 710 on AS/400, but it seems TMKSVR is not supported in this new version. As mentioned in installation guide, is it mandatory to have a X window server for sapinstGUI? Is there an alternative for that, like remote installation -nogui?
    Here's what I tried, Logon AS/400 host with *OFR user and goto installation master folder, run CALL PGM(QP2TERM) PARM(u2019./sapinst -noguiu2019) or ./sapinst -nogui in Qshell, after extracting there's an error showing as below:
    [==============================] | extracting...  done!
    SAPINST000 created and allocated to be used in for this SAPinst instance.
    Starting GUIServer using:
      SAPinst port  : 21200
      GUIServer port: 21212
      HTTP port     : 4239
      GUI autostart : off
      GUI mode      : normal
      command       : /tmp/sapinst_exe.18239.1233264487/jre/bin/java -Xmx256M -Ds
    ap.env.var.javahome=SAPINST_JRE_HOME -cp /tmp/sapinst_exe.18239.1233264487/JAR/instgui.jar SDTServer rootdir=/home/SAPINSTU/.sdtgui config=jar:sdtserver.x
    ml guiport=21212 httpport=4239 -nolock -srvarg=/SAPinstService/host=localhost
    -srvarg=/SAPinstService/port=21200 guistart=off
    ERROR      2009-01-29 16:29:07.453 [syuxcgroup.cpp:826]
               CSyUserImpl::addToOS() lib=syslib module=syslib
    ERROR      2009-01-29 16:29:07.454 [syuxcgroup.cpp:842]
               CSyUserImpl::addToOS() lib=syslib module=syslib
    Opened sylib712.o
    exe dir is /tmp/sapinst_exe.18239.1233264487
    Initialized SAP kernel tracing to file /tmp/sapinst_exe.18239.1233264487/dev_
    sap_kernel
    Initialized SAP kernel tracing to file /tmp/sapinst_exe.18239.1233264487/dev_
    sap_kernel
    unknown message ID (syslib.process.currentProcessEnv.cwdSuccessful) with para
    meter(s):
      /tmp/sapinst_exe.18239.1233264487
    Opened /tmp/sapinst_exe.18239.1233264487/iaguieng712.o
    unknown message ID (syslib.process.currentProcessEnv.cwdSuccessful) with para
    meter(s):
      /InstCDs/PI710/71Master/DATA_UNITS/IM_OS400_PPC64_DB4
    checking existence of account user="sapinstu" uid="202" succeeded with true.
    inserted account (sapinstu, 202, USER) into the accountcache.
    receiving and sending on port 21200
    doStartGuiServer() is now running...
    java is: /tmp/sapinst_exe.18239.1233264487/jre/bin/java
    A child process has been started. Pid = 18250
    getgrnam set errno to : 3 (No such process)
    unknown message ID (syslib.account.isExistingOnOsSucceededFalse) with paramet
    er(s):
      sapinst
    unknown message ID (common.functionReturn) with parameter(s):
      getgrnam(sapinst)  No such process
    Exception thrown near line 948 in file syuxcgroup.cpp
    Stack trace:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", create=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 715: bool CSyUserImpl::isExistingOnOS()
    syuxcgroup.cpp: 873: CSyGroupImpl_getOsInfos(iastring sName, iastring sID, tS
    yGroupInfo& msGroupinfo)
    At line 948 file syuxcgroup.cpp
    Call stack:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", cr
    eate=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 715: bool CSyUserImpl::isExistingOnOS()
    syuxcgroup.cpp: 873: CSyGroupImpl_getOsInfos(iastring sName, iastring sID, tS
    yGroupInfo& msGroupinfo)
    unknown message ID (common.functionReturn) with parameter(s):
      getgrnam(sapinst)  No such process
    Failed action:  with parameters
    Error number 3 error type C_ERRNO
    checking existence of account group="sapinst" succeeded with false.
    A child process has been started. Pid = 18251
    Child process 18251 returned 255
    unknown message ID (common.applicationReturn) with parameter(s):
       system CRTUSRPRF USRPRF(sapinst) GID(*GEN)  255
    unknown message ID (syslib.process.processOutput) with parameter(s):
       system CRTUSRPRF USRPRF(sapinst) GID(*GEN)  CPF2214: User profile SAPINST a
    lready exists.
    Exception thrown near line 834 in file syuxcgroup.cpp
    Stack trace:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", cr
    eate=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 775: CSyUserImpl::addToOS()
    At line 834 file syuxcgroup.cpp
    Call stack:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", cr
    eate=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 775: CSyUserImpl::addToOS()
    unknown message ID (syslib.process.processOutput) with parameter(s):
      system CRTUSRPRF USRPRF(sapinst) GID(*GEN)  CPF2214: User profile SAPINST a
    lready exists.
    unknown message ID (common.applicationReturn) with parameter(s):
      system CRTUSRPRF USRPRF(sapinst) GID(*GEN)  255
    Failed action:  with parameters
    Error number 201 error type SPECIFIC_CODE
    unknown message ID (syslib.account.creationFailed) with parameter(s):
      group="sapinst"
    Exception thrown near line 844 in file syuxcgroup.cpp
    Stack trace:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", cr
    eate=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 775: CSyUserImpl::addToOS()
    At line 844 file syuxcgroup.cpp
    Call stack:
    syuxcaccmg.cpp: 401: PSyGroup CSyAccountMgtImpl::createGroup(iastring sName,
    iastring sID) const
    syxxccache.cpp: 246: CSyAccountCache::getGroupImpl(name="sapinst", sid="", cr
    eate=true, ISyAccountMgt::eAccountType, ISyProgressObserver* )
    syuxcgroup.cpp: 213: CSyGroupImpl::CSyGroupImpl(sapinst, , bool bCreate)
    syuxcgroup.cpp: 775: CSyUserImpl::addToOS()
    unknown message ID (syslib.account.creationFailed) with parameter(s):
      group="sapinst"
    Failed action:  with parameters
    Error number 201 error type SPECIFIC_CODE
    sending SIGKILL to process with id 18250
    unknown message ID (syslib.process.task.taskCancelled) with parameter(s):
      0
    Child process 18250 terminated by signal 9
    Unable to init; unknown execption was thrown .... SAPInst will terminate now...
    I appreciate your attention and help.
    Thanks and best regards,
    Effan

    Hi Efan,
    The "New Features" section of the installation guide explains some of the changes for 710 base installations.
    Running SAPinst
    Without GUI:
    The right command to start sapinst from the Command Line is as follows (each parameter in single quotes): CALL PGM(QP2TERM) PARM(u2019./sapinst' '-noguiu2019)
    For a shell interface, you must use QP2TERM (call qp2term) instead of QSHELL.
    That starts SAPinst in you iSeries machine. To run a GUI for it, you can follow the instructions in SAP Note 966719. Download 'SAPinstgui for Windows Server on IA32 32bit' (51033240_41)
    and execute sapinstgui.exe on Windows.
    With xWindows GUI
    There is a tools for developers kit that allows you use VNC with iSeries: For more information, go to http://www-03.ibm.com/servers/enable/site/porting/tools/
    Furthermore, tools like Hummingbird, cygwin and other open source xWindows servers can be used.
    All that said, I see in your logs there is a problem with the user SAPINST
    system CRTUSRPRF USRPRF(sapinst) GID(GEN) CPF2214: User profile SAPINST a
    lready exists.*
    In the installation guide explains that the formally used user SAPINST must be deleted in order for the new 710 SAPinst tool to create a group called SAPINST. This was done to align the iSeries installation with the other platforms ones. I recommend that when deleting user SAPINST, all owned objects should be transfer to other user instead of deleted. You can use QSECOFR to even better, create a new user SAPiUSR and then transfer SAPINST objects to it.This will avoid deleting objects that might be used in other installations and you can use the new user SAPiUSR for rest of the isntallations.
    Regards,
    Luis Gonzalez

Maybe you are looking for