IBook crashed and now gets stuck on setup assistant

Hi
My friends iBook running Leopard had a kernel panic when updating system software and now every time he tries to start up it goes straight to the setup assistant. If you quit setup assistant it goes to a blue screen and then straight back to setup assistant. Everything still seems to be there as there's only 4GB of space left on the hard drive, i've tried going through the "Your Mac wont start into Mac OS X" page and nothing has helped.
Any help would be really useful!
Thanks
Ben

you could try connecting to another Mac in target mode to access the drive,
another thing to try is to back everything up to the external drive and erase/reinstall everything again.
strange startup problems could be caused by failing hard drive also.

Similar Messages

Photoshop CS3 crashing and installation getting 'stuck'

Last week Photoshop CS3 started crashing when trying to select a new file to open.
This didn't seem related to any particulr file and appeared to be random.
Error message was "an unrecoverable problem has occurred, Photoshop will now quit"
Actully it didn't quit and had to be force quit.
This was happenning sporadically, but today it happened every time I tried to open any image file.
Thinking it was a good idea to re-install, I tried that but the installation got 'stuck' and couldn't be completed.
A few minutes into the installation, prompts appeared asking for the CS4 Flash disk [which we bought seperately]
and then asked for the CS3 Application disk again. That disk was put in the drive and a minute or so later it asks for the CS3 Application disk.
Which is the disk it already has...
Has anyone else had this odd situation and found a solution?
Any thoughts appreciated!

Try resetting your preferences as described in the FAQ.
http://forums.adobe.com/thread/375776?tstart=0
You either have to physically delete (or rename) the preference files or, if using the Alt, Ctrl, and Shift method, be sure that you get a confirmation dialog.
This resets all settings in Photoshop to factory defaults.
A complete uninstall/re-install will not affect the preferences and a corrupt file there may be causing the problem.

MacBook suddenly froze, rebooted and now gets stuck

Hi,
These forums have been helpful in the past, so I thought I might try them again.
My MacBook circa 2006 (with a different hard drive and updated keyboard/trackpad section courtesy of Apple in mid 2009) has suddenly stopped working. It was working fine until it suddenly froze. I was playing music at the time and it looped the same 1 second over and over. I powered it off by holding the power button.
I waited around a minute then powered it on again. It did the chime, displayed the Apple logo, but then got stuck (it didn't get as far as displaying the pinwheel).
I attempted to reset the PRAM (descibed here: http://support.apple.com/kb/HT1379 ), which seemed to do nothing.
Also attempted to restart while holding CMD + S, which got stuck on the following lines:
IOAPIC: Version 0x20 Vectors 64:87
ACPI: System State [S0 S3 S4 S5](S3)
I don't think it's a hard drive failure - no clicking sounds and it seems to work properly (judging from the normal sounding HD sounds coming from it when I tried the CMD+S reboot).

Try starting in Safe Mode.
http://support.apple.com/kb/TS2570
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

I can no longer import pictures to my ibook (OSX version 10.6.8) using iphoto 09 version 8.1.2 and now get message that file is in an unrecognizable format. What is wrong? Same camera as before.

I can no longer import pictures to my ibook (OSX version 10.6.8) using iphoto 09 version 8.1.2 and now get message that file is in an unrecognizable format. What is wrong? Same camera as before.

Julesvernet
As a Test:
Hold down the option (or alt) key and launch iPhoto. From the resulting menu select 'Create Library'
Import a few pics into this new, blank library. Is the Problem repeated there?

PC crashed and now using a different PC. How do I get my iTunes library back from the failed PC on the PC being used now?

PC crashed and now using a different PC. How do I get my iTunes library back from the failed PC on the PC being used now?

Extract the hard drive from the faulty computer and recover the library from it or see Recover your iTunes library from your iPod or iOS device. (At least one link in there may be useful even if you don't have such a device.)
tt2

I bought htc 8x verizon employee edition and when i update it and during installation with my error phone get off and now phone stuck on some wheel running thing and wont get on please tell me if i could download the rom

i bought htc 8x verizon employee edition and when i update it and during installation with my error phone get off and now phone stuck on some wheel running thing and wont get on please tell me if i could download the rom or anything also

Hi mnomi! Sorry to learn of the trouble you're running into with your new phone! Have you already switched the device via your My Verizon : http://vz.to/16lkVUY Once you have done this, and verify the sim card is inserted securely, the activation will begin. If the phone is stuck on the wheel and you cannot move forward, you may want to do an alternative reset. Please follow the below instructions:
1) Ensure the device is powered off.
2) Press and hold the Volume Down button (located on the right edge) until instructed to release in step 4.
3) Press and hold the Power button (located on the top-right edge) until the device vibrates (approximately 2 seconds) then release.
4) When the restore screen appears (exclamation mark), release the Volume Down button.
5) From the restore screen, press then release the following keys to initiate the reset process:
1. Volume Up button
2. Volume Down button
3. Power button
4. Volume Down button
*Allow several minutes for the process to complete (rotating gears appear on the display to indicate that the reset is in progress).
If you have any further questions or concerns, please let us know. Keep us posted if this resolves your concerns. Thanks!
-KristieQ_VZW
Follow us on Twitter @VZW Support

Why when I tried to update itunes it crashed and now I get a MSVCR80.dll was not found and can not start my itunes any more

Why when I tried to update itunes it crashed and now I get a MSVCR80.dll was not found and can not start my itunes any more?

Solving the iTunes Installation Problems in Windows
1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

Visual Studio 2013 Setup and Installation gets stuck at system restore point. what are the issues?, help me out!!!

Visual Studio 2013 Setup and Installation gets stuck at system restore point. what are the issues?, help me out ASAP

Hello nitinrathod29,
There are some possible fixes for this issue.
Please check the following thread:
https://social.msdn.microsoft.com/Forums/vstudio/en-US/47bc6990-00f2-4d85-b3f8-9de03c637f43/visual-studio-2013-update-2rc-stucks-on-creating-system-restore?forum=vssetup
https://social.msdn.microsoft.com/Forums/vstudio/en-US/81478f51-37bb-4dbb-bd0c-beade1fd50ab/visual-studio-2012-professional-installation-getting-stuck-creating-a-system-restore-point?forum=vssetup
So here are them:
1. Check if you have any software which may prevent the installer from running. For example, Windows Defender or any other software which may restrict your permissions.
2. Just start the computer.
3. Run the setup as admin.
4. Check your UAC permissions.
Best regards,
Barry
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

I updated my iPhone 5 yesterday to iOS 8.1.3, now the touch screen isn't responding, keeps opening aps and then get stuck.

I updated my iPhone 5 yesterday to iOS 8.1.3, now the touch screen isn't responding, keeps opening aps and then get stuck. Can't hang up after making a call. Can't close messages. Have I done something wrong?

Good day catjono,
If you are having an issue with your iPhone's touchscreen not responding, I would suggest that you troubleshoot using the steps in this article -
If the screen on your iPhone, iPad, or iPod touch doesn't respond to touch - Apple Support
Thanks for using Apple Support Communities.
Safe computing,
Brett L

Mac crashed and now upon restart I cannot launch any applications. When I try to, I just get the colorful pinwheel spinning, spinning, spinning...

mac crashed and now upon restart I cannot launch any applications. When I try to, I just get the colorful pinwheel spinning, spinning, spinning...

Troubleshoot the spinning beach ball

Trying to update to 10.7 I tunes to windows 7 64 bit and download gets stuck and can't switch it off without crashing computer-pain and frustrating,can anyone at apple help?

Trying to update to 10.7 I tunes to windows 7 64 bit and download gets stuck and have to crash the computer to stope download window to try other options-it's been the same all week
Even when I try to download 64bit updated as forums say it gets stuck.
You would have thought it should be a simple update as usual.
Any advice
Thanks,

I'd first try downloading an installer from the Apple website using a different web browser:
http://www.apple.com/quicktime/download/
If you use Firefox instead of IE for the download (or vice versa), do you get a working installer?

HT3606 i keep trying to update the software and it gets stuck on configuration, so i can i sped up the process?

i keep trying to update the software and it gets stuck on configuration, so i can i sped up the process?

Some general advice on updating:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious! In fact a second restart can be recommended.
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a week or two while you regularly check their websites for updates.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
[b]If you are updating Safari (or just have):[/b]
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very [i]first[/i] thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
/Library/InputManagers
~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).
Solutions for troubleshooting installation, startup, and login issues in Mac OS X v10.5
http://support.apple.com/kb/TS1541?viewlocale=en_US

Firefox was working fine in the morning, after half a day, it just crashed and now every time i try to start FF it crashes, i reinstalled FF, even tryed FF 4 beta, every time same crash report window, and nothing happens.

After a half day working normally, FF just crashed, and now i reinstall it, even tryed FF 4 beta, and still getting crash report. Cant even start in safe mode, same crash report window pop up.
Checked for viruses, malwares. Nothing helped.

Other applications print okay? If so, try deleting the Preview .plist
You need to look in your user Library/Preferences for the .plist. Hold down the option key while using the Finder "Go To Folder" command. Enter ~`/Library. Delete the .plist(s) for the application.
If you prefer to make your user library permanently visible, use the Terminal command found below. It does work with Mountain Lion:
http://osxdaily.com/2011/07/22/access-user-library-folder-in-os-x-lion/
You might want to bookmark the command. I had to use it again after I installed 10.8.2. I have also been informed that if you drag the user library to Finder it will remain visible.

Why does illustartor CC open then crashes and i get a message saying windows don't know the prob?

why does illustartor CC open then crashes and i get a message saying windows does not know what the problem is. everytime i open it, Now i know it works on my computer becuase i've used illustartor plenty of times on my current desktop but ever since today its been acting wierd and work so i've unistalling and reinstalling but still nothing works then i tried installing on another hardrive still did not work and i cleaned out my registryies, optimized my disk, and cleaned temp files tooo so i just do not know what went wrong and i really need help i have class assignments that i have to get done in illustartor so if anyone can help me and let me know what the problem is and what i have to do i would really apreciate it.

Hi J,
- Do you see an AICC splash screen? If yes then could you please let us know where exactly it crashes i.e. while loading which plugin or font?
- Do you have any 3rd party plugins installed? Can you please remove those (do take a backup of them) and see if AI launches fine? This way you would be able to find the plugin creating the problem.
- Did you install any OS or Ai update after which it started showing the problem?
- Please check if you have all the Verdana family fonts installed.
Let me know if any of these work.
Thanks,
Dhirendra

Hi my firefox crashed and now wont restart, I cant past the crash reporter the crash report id is: bp-1a14605e-a13b-4ae6-b459-ca0792111124 thanks

it suddenly crashed and now wont restart. A crash reporter keeps coming up but nothing happens

I cant even get the internet on, (im currently on my boyfriends laptop) when I turn my desktop on it goes to the crash report but wont let me send it- it then just starts doing its own thing, i cant even log off i just have to turn it off, i cant click on any icons, it wont let me so i cant open firefox in safe mode....any clues?

IBook crashed and now gets stuck on setup assistant

Similar Messages

Maybe you are looking for