IBook G3 can't boot from hard disk or cd

Hello,
Just recently my laptop suddenly just would not start-up anymore. Here are it's symptoms and what I have tried:
-When the computer starts up I get the folder with the flashing "?" mark sign.
-I tried reseting the PMU and the PRAM and NVRAM (via Open Firmware) no luck.
-I tried booting from the Mac OS X installer CD (for Disk Utility) and the DiskWarrior CD by either holding "c" or "option" (i don't think it is a CD problem because the CD appears as an selection (hard drive doesn't) when I hold "option"). Unfortunately, when it goes to the grey apple on white screen with the wheel the apple becomes a no sign after about 30 seconds.
-I have tried to use "fsck" but I can't startup into single-user mode using Command+S
-I cannot start-up in Safe Mode
-I started it up in target mode (holding "T") but my other computer does not mount it on to the desktop and Prosoft Data Rescue X doesn't recognize the volume.
-I tried replacing the RAM (256mb) with the stick that came with the computer (128mb).
These are all the things in my problem-solving knowledge that I have tried and still can't fix it. If anything I just want to get the files off of it if that's possible.
The computer is an iBook G3 Dual USB 800MHz
Running Mac OSX 10.3.?
No Airport Card
256 MB Ram (at the moment)
Thanks for any help...
iBook G3 Dual (problem computer), eMac G4 (good computer)   Mac OS X (10.3)  
iBook G3 Dual (problem computer), eMac G4 (good computer)   Mac OS X (10.3)  

Hi, and welcome to Apple Discussions.
You have tried some of the recommendations in this Apple Knowledge Base article:
http://docs.info.apple.com/article.html?artnum=50959
But I hope something there will help.

Similar Messages

  • Can't boot from hard disk or from windows 7 recovery dvd

    I have a 970A-G46 motherboard.
    I can't boot from hard disk or from a windows 7 recovery dvd.
    If I move the hard drive to another PC, it boots fine.
    If I put the DVD in another PC's dvd drive, it can be accessed.
    This machine will boot from an Ubuntu dvd and I can then access the HD directories and the recovery dvd.
    What do I need to do?
    Help and thanks

      "I can't boot from hard disk or from a windows 7 recovery dvd."
     What is that DVD from? Is it from a previous computer of some kind? Same question for HDD and the OS on it.

  • Satellite L10-144 - Can't boot from Hard Disk

    Hello.
    Sorry for my english because I'm french. I have a problem with boot on this computer. I have installed windows xp on my hard disk but the computer don't boot on this hard disk. If I want to boot on this hard disk I must push F12 and select hard disk and after windows load.
    In the bios the hard disk is in first but this hard disk don't boot automaticly.
    Can you help me please?
    Thanks a lot.

    Hi Demilego,
    Thats really strange... Normally the computer should boot from HDD automatically.
    In your case I would check the BIOS and load the default settings.
    Does it work?

  • I can't boot from instalation disk need help

    can anyone tell me why i can't boot from instalation disk
    i burn a DVD with verified iso with MD5 with Nero Express

    i use burn image , of course and
    i have a Sempron +2400 with asus a7s8x mainboard
    and i download all 5 file for DVD x86 and then i copy /b all this files.
    when computer boot from cd the screen is bleu with Solaris ................ v.20 message and after 1 second message became
    Aolaris ..................v.20 and computer remain in this position

  • Godane's Archlinux boot from hard disk but it can't login in with slim

    I download Godane's archiso-live-2009-09-24.iso , i havent cdrom , so i boot it from hard disk .
    I extract iso to drive C: (fat32) ,two folder is "boot" "archiso-live"
    my menu.lst  is :
    title Boot archiso-live Desktop
    root (hd0,0)
    find --set-root /boot/initrd.img
    kernel /boot/vmlinuz  elevator=deadline ramdisk_size=60% aufs nonfree=no vga=791
    initrd /boot/initrd.img
    load=overlay.lzm
    The iso can be boot from hd ,but there isnt slim . only is console...
    what can i do with this problem??

    I think your problem is that load=overlay.lzm is in the wrong place.
    Here is what i should look like:
    title Boot archiso-live Desktop
    root (hd0,0)
    kernel /archiso-stable/boot/vmlinuz elevator=deadline lang=en_US keyb=us load=overlay,mesa usbdelay=5 nonfree=no xdisplay=old xdriver=no from=/dev/sda3/archiso-stable changes=/dev/sda3/changes session=xfce cdname=archiso-live
    initrd /archiso-stable/boot/initrd.img
    I use 'from' boot option so i can boot from my hard drive more easier. The way its booted above is for 2009-12-08 version of my archiso-live. Just thought you should know.
    I hope this helps. And sorry for it being so late.

  • Ibook g4 won't boot from install disks

    Got an ibook g4 1.33 ghz combo drive from original owner w/install disks. I want to reinstall original system but it won't boot from install disk 1. Tried starting holding down c but ignores disk. Holding down option just gives me the HD. Install disk shows up on desktop and opens. Tried disk utility from install disk but it doesn't allow me to erase the hd. Is there anything else I can do? Thanks.

    OK, so let us suppose that you have the correct disk, the possibilities are:
    • the optical drive is not functioning properly. However, since the disk shows up on the desktop the drive is apparently reading it.
    • the disk itself is the issue. It could the wrong disk, but let us assume it is not. It could be damaged so that it is no longer bootable, or it could dirty. I would begin by giving the disk a good buffing and see if that will encourage it to boot the computer.
    Good luck.
    cornelius

  • Can't boot from Install Disk for Leopard

    I purchased the new xeon core dual which only boots in Leopard. I need to put Leopard on an external drive, so I purchased Leopard and tried to install it on an external drive. My computer starts to read the disk but before it even gets to the blue screen, it stops, scrolls down in a dark gray screen and says I need to restart by holding the power button down. The screen kind of looks like a kernal panic with oriental writing under the english.
    I have tried by restarting and holding down the "c" key with no luck. I tried again with holding down the "option" key and when the hard drive and disk show up as choices. I chose the disk and still no luck. I disconnected all my external drives and tried again with no luck. I called tech support and they said it may be my optical drive. They set up an appointment with the genius bar at my local apple store. The genius listened to my drive and said there was nothing wrong with the drive and that it probably was a bad disk so they gave me a new one. Went home and tried with the new disk and same problem. Can anyone help?!! Thanks.

    I purchased the new xeon core dual which only boots in Leopard.
    I need to put Leopard on an external drive, so I purchased Leopard and tried to install it on an external drive.
    There's your problem. Macs which ship with Leopard can't boot Leopard retail, unless it is newer than the Mac in question. Check the version of Leopard on the Leopard retail DVD you purchased in the second quote. If it is older than what was installed on your Mac Pro based on the Mac Pro install and restore DVD, then it won't work on your Mac Pro. If you want Leopard of the Mac Pro to be backed up to be an emergency boot volume for the Mac Pro on the external drive, use a cloning software*:
    http://www.macmaps.com/backup.html
    Or follow these directions to backup your Mac Pro DVD*:
    http://www.macmaps.com/bootcd.html
    If you need an emergency Leopard volume for another Mac, install it directly from that other Mac. If that other Mac lacks a DVD drive, get a Firewire DVD drive to do it.
    - * Links to my pages may give me compensation.

  • Macbook Pro doesn't boot from hard disk

    I recently applied an open firmware password to our Macbook Pro.
    A co-worker tried to boot via the t-funtion which obviously doesn't work when the open firmware password is active. He forget to contact me so he tried to get it to work using some startup shortcuts. The folowing he had done:
    * starting up while holding shift;
    * starting up while holding command + option + P + R;
    * having the accu out for a while
    * starting up while holding shift and let the Mac on for a night
    It seems that starting up from the Macintosh HD seems somehow blocked. THe system hangs on the Apple grey splashscreen with the loading icon turning.
    I tried the following:
    * Tried resetting PRAM using Option + Command + P + R (didn't hear any chimes);
    * Trying to reset Open Firmware Password using Option + Command + O + F (nothing happens)
    The most promising solution came when holding down the Option key: I got the lock and entered my Open Firmware Password. I was able to boot from the install disc. In the disc utility I verified the hard disk and repaired some permissions. I didn't get error messages. THen I used the startup utility and selected the hard drive as startup disk.
    But when I restart the computer, it still hangs on the splash screen. So for now i've run out of ideas.
    Message was edited by: StefSOFT
    Message was edited by: StefSOFT

    With intel Mac they changed to EFI firmware so a lot has changed. From reading this I think if you can get to install disk utilities then why not uncheck +Require password to change Open Firmware settings+ on Firmware Password Utility and that should free up the troubleshooting steps you list above that are blocked. Reinstall of OSX seems logical to attempt. Sadly without further testing could be hardware issue too, need to contact apple authorized service provider in this eventuality. One thing to bear in mind was whether your co-worker altered the firmware in any way, this might invalidate Apple One-Year Limited Warranty, AppleCare Protection Plan, or other AppleCare agreement.

  • Intel Xserve will NOT boot from hard disk drive

    I have two Intel Xserves 2.0 QC machines
    I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
    When booting from The installation DVD media
    The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
    Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
    If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
    It does show, the still inserted Installation DVD.
    I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
    I have tried different caddy postions (left, middle and right)
    I have tried bona fide Apple supplied Disk drives
    I have tried various different caddies
    I have tried installing Operating System 10.5.*  and  10.6.8 server
    I have run SMC reset and system reset
    But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
    Has anyone seen this behaviour?
    Is it fixable?
    Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
    I have now run out of ideas and cannot find any help in discussions or just googling.
    ANY help would be very appreciated
    Regards
    Tony

    Antonio Hi !
    QC = Quad core  or  QX as it is written on the "pull out" serial number tab at rear of system
    I have 3 late 2006 Intel xserves
    On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
    2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
    the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
    I have many different Caddies and these have different product/model number labels
    603-9965
    603-9545
    603-9796
    these are marked "intel SATA"
    The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb  -  all of which have been used in systems at one time or another
    and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
    Thanks for the guide - I will look through that and continue to try and find an answer

  • Can't boot from install disk, and says no airport card installed, HELP!

    I bought a new Macbook Pro a few months ago, which recently had to go in for repair to have the screen changed. It came back with the new screen fitted but they had done a terrible job at aligning the lid, so it went back again. Came back and all looked good, until i booted up and realized that where my wifi icon is at the top of the screen, it wasn't connected. When clicking it to bring down the drop down menu of available wifi spots, all it said was "No Airport Card Installed"....Thinking a repair of disk permissions might be worth trying, I tried to boot from my OSX install disk holding down C, however when holding down C all it does is go on a constant loop of restarting, not even reaching the Apple logo. If I don't hold down C then it simply boots to the desktop, so i'm unable to access disk utility correctly to run a repair.
    Being pretty fedup with the whole situation, the laptop has now gone back for a 3rd time, as it never had these two issues before. I was just wondering if anyone had any idea what might have caused this? And how a status of no airport card installed and a drive that wont boot a disk normally can be related?
    I'll be getting it back on Tuesday, but i just wanted to know what the heck they might have done to have screwed things up.
    Thanks
    Phil
    Message was edited by: Philip Dexter

    Hi Phil,
    I can't say for sure, but it sounds to me like they didn't reconnect the WiFi hardware when replacing the screen. To my knowledge, the Airport "hardware" (including the antenna) is located inside the screen hinge. When the screen was replaced (and the hinge not properly aligned) perhaps someone improperly connected the Airport hardware, or forgot to connect it entirely.
    The reason the WiFi hardware is located in the hinge is because that is the only plastic area of the entire notebook. Radio signals do not travel well through aluminum, so some area of the computer has to be plastic to allow that signal to get through. The hinge is the only area where that's possible.
    As for the reason why the machine wouldn't boot up from the disc, I have no idea. Here's hoping it does when it comes back. If I were you, I'd have a chat with Apple Customer Relations about the situation.
    --Travis

  • Can't boot from install disk and I need to reinstall OS X 10.4

    I am trying to boot from the install disk by restarting the computer and holding down the c button. It won't start up from the disk. I get a white screen and an icon that is a circle with a line through it. I am having that problem on all my iMacs in my lab and I don't know why. Help Please!!! thanks.

    Sorry for all of the posts.. but it could be possible that the firmware is password protected - disabling users in the computer lab from corrupting programs? I found this article and it might help.. (http://www.fif3.com/howto/archives/001983.html) Some of the article is below....
    ALSO: if you use open firmware password... you'll need this:
    Startup Manager -accessed by pressing the Option key during startup
    Enter commands after starting up in Open Firmware -press Command-Option-O-F key combination during startup.
    http://docs.info.apple.com/article.html?artnum=106482
    How to troubleshoot a computer with Open Firmware Password enabled
    If you cannot access the Open Firmware Password application and need to troubleshoot your computer by:
    Resetting the PRAM
    Starting up in Single-user mode
    Starting up in Verbose mode
    Starting from CD-ROM
    Then follow these steps:
    Start up into Open Firmware by pressing and holding the Command-Option-O-F key combination during startup.
    At the Open Firmware prompt, type: reset-nvram
    Press Return.
    When prompted for your password, enter it and press the Return key. It responds OK.
    At the Open Firmware prompt, type: reset-all
    Press Return.
    The computer restarts and you are now be able to reset the PRAM and startup in Single-user mode, Verbose mode, or from CD-ROM.

  • Can not boot from Hard Drive and or CD

    Hi
    I have a SUN Blade 1000. I loaded Solaris 10 a few days ago
    and had it running pretty good until I ran an update program.
    Now I cannot boot the dam thing. IT just hangs at a * prompt somwhere in the boot process.
    I would like to re load Saolaris 10 but do not have a clue how to
    make the machine boot from the CDROM if I cannot get to the OK prompt and I cannot get to ANY prompt that will let me get ANYwhere for that mater.
    Is there some key or combination of keys I could push or something to get this dam thing to boot from the CDROM so I can start over???
    Thank you in advance.
    I have almost no experiance with SUN Solaris on SPARC or any other platform.
    I know Windows and x86 hardware very well and have built many machines.
    Is there a way to get into the Bios at boot time like with an x86 system? The last question is not as important as the first one of how do I boot this pig from the CD.
    Thanks
    Jim

    How did you begin the previous installation?
    Have you spent any time reading these forums?
    Use the forum search function, keywords ...
    "get to the ok prompt"
    (in quotation marks)

  • Booting from hard disks 2TB - bootable USB flash drive GRUB (w/o OS)?

    Hi,
    I'm thinking about setting up a hardware supported RAID on a Debian-server (Proxmox) with lots of HDD-space. Therefore, my RAID-array will be >2TB, but I've read that the BIOS of the system will not be able to boot from such. Do you have a solution for this?
    I was thinking about installing a bootable GRUB on an USB flash drive, which would then chainload the RAID's GRUB for booting. Is this even possible? I couldn't find any tutorial on how to create/boot only a (customizable) GRUB from the flash drive.
    Another option would be to create multiple disks by the RAID-controller, but i'm not sure what happens with the chunks, if i would add another disk to the RAID to expand it.
    A third solution, that came to my head, is simply installing Proxmox on a separate disk and detach it from the RAID. But in case of a disk failure, it would not be protected and i would rely on snapshot-backups - so i rather would not like to go with that solution.
    Let me know what you think!
    VR

    I don't know about the answers to your issues, as I have never tried any disks that large.  But it would probably be wise not to mention that you are trying to do this on a non Arch system, as now I am pretty sure you will not recieve the help you desire.
    I don't mean to say that I encourage you to try to dupe our community into helping you with your debian system by not mentioning it.  But it seems pretty silly to come to the Arch threads looking for debian support, even if it is a universal (os independent) issue.

  • IBook g4 won't boot from CD or read CD but will boot from and read DVD

    My iBook won't read from CD's anymore. I can put in my 10.4 Tiger DVD and it boots just fine and will mount just fine but when I insert a CD it will think for abou 10-15 seconds then eject it. I can't get it o boot with any diag tools on CD either. Any tricks

    I've been having a similar problem. Can't boot from diagnostic disks (Disk Warrior, Norton, and can't use certain functions of Disk Utilities on Mac OS disk). What's more, I now have 3 partitions on my hard drive and I didn't partition it! I tried wiping the HD but I still ended up with 3 partitions. Permissions keep changing on my files. I haven't been able to access the other volumes to see what's there. I feel as though something on one of the other volumes has taken over the admin privileges for my iBook.
    NAV finds nothing, but also tells me I haven't permission to scan certain files in the priv, usr, bin, and similar files.
    Disk Utility repairs permissions temporarily, but only on the one partition I can access. When I try to use it to look at other vols from the CD, it shuts down and restarts my computer from the HD.
    What's going on and what can I do about it? Apple claims it's impervious to rootkits et. al., but I'm beginning to think one has gotten onto my system.
    Has anyone else heard of similar behavior and a way to remedy?

  • Equium L300 - Cannot boot from recovery disk or other CDs

    Equium L300
    bought new used 3 months the left for 9 months. Dead flat battery.
    On restart
    boot from hard -> disk Bootmgr is corrupt will not boot
    boot from Recover disk cd -> The file is possibly corrupt. The file header checksum does not match computed checksum
    boot from dvd windows install -> same as above
    Tried numerours disks but will not boot.
    No will it boot from USB stick. Pulled hard disk tried elsewhere seems ok.
    Bios looks ok and sees hard disk and dvd etc
    Any ideas otherwise a pretty dear machine for two monthe use.
    Was just out of guarantee before fault appeared
    Thanks chris

    Hi buddy,
    > But still think bios is corrupted
    If you think so, then contact your authorized service provider. The technicians can check your notebook and try to reflash the BIOS. The technicians are really experts and so this shouldnt be a problem for them.
    Here you can search for one:
    http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider

Maybe you are looking for