IC WebClient Dial-Up access

We will be implementing CRM 4.0 in the near future. For some of our users, who may be on the road, dial-up access may be the only connectivity option. Has anyone used the IC Webclient in this capacity? Thanks

Chris,
IC Webclient is a completely different product than CRM4.0. The IC stands for Interaction Center, which indicates that it is targeted at call/interaction handling.
CRM4.0 has a web interface. So, whether you are in the office or on the road (again), you just new web access back to your company and a browser. Depending on your dialup access (minimum 56Kbps), it should work OK. However, keep in mind that such dailup access usually has large latency times!

Similar Messages

DSL in the city, do we have dial up access numbers in upstate?

I have DSL in the city, do we have dial up access numbers in upstate?
Anyone know who to call for that number?
Thanks
Ñin

An Air card that someone is talking about would have to be something along the lines of 3G or 4G USB adapters. These are of course, Wireless data plans that use the cell phone towers so you'd need to make sure that signal is good out where you are anyways to even get that. Other than that, it's slow as heck satellite or trying to convince Verizon to set up pole-mounted DSLAMs somewhere within 2 miles of you for DSL. ISDN could be an option though I don't think Verizon installs those too much any more, and they would only give 128k of bandwidth anyways, despite lower latency.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Dial-up access on 2851

disregard conversation

so apple no longer makes dial up modems?
They withdrew the USB modem a year or two back, which is extremely unhelpful as I don't think any modern Macs have them built-in. Even though I have cable broadband, I have some webspace with another provider which can only be accessed by dialling in (so they can charge) and though I do have the modem there must be lots of other people in this situation, quite apart from those who have only dial-up access.

Dial up access?

how can I get dial up access? apparently, apple no longer sells their external 56k modems anymore, and I'm in a bind since DSL is not available in my parents summer home!

so apple no longer makes dial up modems?
They withdrew the USB modem a year or two back, which is extremely unhelpful as I don't think any modern Macs have them built-in. Even though I have cable broadband, I have some webspace with another provider which can only be accessed by dialling in (so they can charge) and though I do have the modem there must be lots of other people in this situation, quite apart from those who have only dial-up access.

Help Needed Creating AppleScript for Dial Up Access and Updates

Hello,
Due to my location I can only access the internet via Dial Up. I would like to create a script that wakes up my Mini early in the AM, dials my ISP and checks to see if there are any Apple Updates. I'd like to do this at night so my family doesn't have to compete with updates when they are using the computer.
I've done the Apple Scripting tutorials and have a feel how to do the basics. But I cannot find any information on how to access the USB Modem (US Robotics), get it to dial, access the "Check for Updates" page, download, install and then disconnect.
Can anyone point me to a functional script that will do this or tell me where I can find the modem related scripting commands?
Thanks

1). Does your script both get and install updates if they exist ? If not what should be added to accomplish that?
If you use man softwareupdate to look at the command line options for softwareupdate you'll find:
-i | --install
Each update specified by args is downloaded and unarchived,
and also installed. The install flag requires root. args
can be one of the following:
item ... One or more update names.
-a | --all All appropriate updates.
-r | --req All required updates.
So '-i' tells softwareupdate to install the updates, and '-a' tells it to install all available updates, as opposed to a specific update, or 'required' ones.
2). Can you suggest an addition to the script that will disconnect the dial up modem and then shut down our Mac Mini?
That's going to be harder because, as written, the script performs the softwareupdate in the background. It does that so that you don't run into timeout issues (by default AppleScript will timeout after a certain period, canceling the script in progress). Since it's not clear how long the updates will take to download and install it isn't possible to predict what the appropriate timeout should be.
The easiest way to disconnect would be to just configure the dialup connection to disconnect after a certain period of idleness (System Preferences -> Network -> Modem -> Advanced -> PPP -> Options or some such). If that doesn't suffice let me know and I'll craft up a revised script.

Dial-In access to VRF Lite (MPLS VPN)

Hi,
I'm trying to implement a solution, that gives opportunity to dial-in to some specific customers VPN (VRF Lite)
Configuration of NAS is done using cisco.com guide and seems OK. NAS is using RADIUS to authenticate users, and if authenticated, RADIUS sends a specific users virtual-profile configuration to NAS. So far everything seems OK. I can dial-in, succesfuly authenticate against RADIUS and download the virtual-profile configration (DEBUG is pasted below).
BUT, even there is a command "virtual-profile aaa", and RADIUS sends all info, Virtual-Access interface isn't created or it is created without any configuration.
Maybe this is happening because I'm using dialer-profile ? Some cisco documentation says that if there are dialer-profiles configured, virtual-profile configuration cann't be downloaded from AAA ???
Here is debug, You can see RADIUS to NAS communication:
Aug 24 07:59:59: %LINK-3-UPDOWN: Interface Serial2/0:26, changed state to up
Aug 24 08:00:00: RADIUS(000000A1): Storing nasport 20026 in rad_db
Aug 24 08:00:00: RADIUS(000000A1): Config NAS IP: 0.0.0.0
Aug 24 08:00:00: RADIUS/ENCODE(000000A1): acct_session_id: 247
Aug 24 08:00:00: RADIUS(000000A1): sending
Aug 24 08:00:00: RADIUS/ENCODE: Best Local IP-Address xxx.xxx.xxx.xxx for Radius-Server xxx.xxx.xxx.xxx
Aug 24 08:00:00: RADIUS(000000A1): Send Access-Request to xxx.xxx.xxx.xxx:1645 id 21646/40, len 113
Aug 24 08:00:00: RADIUS: authenticator C9 98 61 51 0F FF 0F C8 - FA A2 3E C1 5E 80 13 0E
Aug 24 08:00:00: RADIUS: Framed-Protocol [7] 6 PPP [1]
Aug 24 08:00:00: RADIUS: User-Name [1] 6 "vrft"
Aug 24 08:00:00: RADIUS: CHAP-Password [3] 19 *
Aug 24 08:00:00: RADIUS: Vendor, Cisco [26] 20
Aug 24 08:00:00: RADIUS: cisco-nas-port [2] 14 "Serial2/0:26"
Aug 24 08:00:00: RADIUS: NAS-Port [5] 6 20026
Aug 24 08:00:00: RADIUS: NAS-Port-Type [61] 6 ISDN [2]
Aug 24 08:00:00: RADIUS: Calling-Station-Id [31] 9 "xxxxxxx"
Aug 24 08:00:00: RADIUS: Called-Station-Id [30] 9 "xxxxxxx"
Aug 24 08:00:00: RADIUS: Service-Type [6] 6 Framed [2]
Aug 24 08:00:00: RADIUS: NAS-IP-Address [4] 6 xxx.xxx.xxx.xxx
Aug 24 08:00:00: RADIUS: Received from id 21646/40 xxx.xxx.xxx.xxx:1645, Access-Accept, len 277
Aug 24 08:00:00: RADIUS: authenticator 8D E7 52 2A 4B 72 88 9E - B8 85 38 CF 70 4A B7 79
Aug 24 08:00:00: RADIUS: Service-Type [6] 6 Framed [2]
Aug 24 08:00:00: RADIUS: Framed-Protocol [7] 6 PPP [1]
Aug 24 08:00:00: RADIUS: Framed-IP-Address [8] 6 10.10.8.5
Aug 24 08:00:00: RADIUS: Framed-IP-Netmask [9] 6 255.255.255.240
Aug 24 08:00:00: RADIUS: Framed-Compression [13] 6 VJ TCP/IP Header Compressi[1]
Aug 24 08:00:00: RADIUS: Vendor, Cisco [26] 54
Aug 24 08:00:00: RADIUS: Cisco AVpair [1] 48 "lcp:interface-config#1= ip vrf forwarding test"
Aug 24 08:00:00: RADIUS: Vendor, Cisco [26] 68
Aug 24 08:00:00: RADIUS: Cisco AVpair [1] 62 "lcp:interface-config#2= ip address 10.10.8.1 255.255.255.240"
Aug 24 08:00:00: RADIUS: Vendor, Cisco [26] 50
Aug 24 08:00:00: RADIUS: Cisco AVpair [1] 44 "lcp:interface-config#3= description horray"
Aug 24 08:00:00: RADIUS: Vendor, Cisco [26] 49
Aug 24 08:00:00: RADIUS: Cisco AVpair [1] 43 "lcp:interface-config#4= encapsulation ppp"
Aug 24 08:00:00: RADIUS: Framed-Routing [10] 6 0
Aug 24 08:00:00: RADIUS(000000A1): Received from id 21646/40
Aug 24 08:00:00: %ISDN-6-CONNECT: Interface Serial2/0:26 is now connected to xxxxxxx vrft
Aug 24 08:00:00: %LINK-3-UPDOWN: Interface Serial2/0:26, changed state to down
Please let me know if any other information is required.

Besides, as I see, virtual-access interface's description is as configured on RADIUS, but all other configuration is from virtual-template. Why? Even if there are no overlapping configuration strings in Vtemplate and on AAA (like ip address etc), configuration string received from RADIUS isn't getting added to virtual-access interface configuration.

Sync with laptop for dial up access

I have a Palm OS 755P with Alltel. I was told that I need to have 700P drivers in order for me to sync with my laptop for internet access. I have had success in the past but I was told my drivers were bad and that they needed to be reinstalled. I tried the 755P driver but it still doesn't work. I can't find where to find the 700p drivers to install. Any help would be appreciated.
Post relates to: Treo 700p (Alltel)

I have no personal experience with tethering. The following support article is the closest match I could find to your question. Does it help?
Setting up a USB Dial Up Networking (DUN) connection for a Treo 700p & 755p smartphone
http://kb.palm.com/wps/portal/kb/na/treo/755p/alltel/solutions/article/42866_en.html

Dial-up access # w/o monthly fee?

I've hung onto my old dial-up account all these years just in case I ever get somewhere wihtout a high-speed connection ... or for those times when the Cable modem goes on the blink and I have to get online. These occasions are fewer and far between, and I'm looking to find a way to stop paying $19.95/month but still have an access number I can use on an as-needed basis for those few times when I need one.
Is there any reliable ISP that offers an access number on an as-needed basis? Or do they all charge a monthly fee?

In the UK you can get a free dial up account however you pay standard call charges for the duration of your connection.
But it is cheaper to get a usb 3g/hdspa modem for a backup connection faster and cheaper than dial up.

Apple iphone4 is locked and will not let me dial or access contacts or recents, etc, can anyone help here?

I can't get my Apple iphone 4 to allow me to access anything (Phone functions only)after it comes up. No dialing, favorites or contacts, etc. What to do to fix it?

What is "locked", the phone or the laptop? When you say locked, what symptoms are you seeing that makes you say it is locked?
Without a working sleep/wake button, then you cannot perform the basic user troubleshooting steps. Your only choice at this point is to let the phone's battery die and see if you can get it reset by then plugging it into the charger.

Out of Band remote management dial in access

I have a cisco 2821 router with a WIC-1AM card in it. The router recognizes it ( ie it shows up as an async interface).
Could someone please point me towards a configuration guide or example that would show me how to configure this for remote access?
The end goal of this is if the internet circuit goes down I can dial into the router to see if it is a router issue and make changes as necessary.
There will be a POTS line connected to the wic card and I have a phone number for the card.
Thank you
Lynne

Hi,
I hope this link helps you:
http://www.cisco.com/en/US/docs/ios/dial/configuration/guide/12_4/dia_12_4_book.html
Best Regards,
Federico.

SRP547W Voice User# Speed Dial Settings - Access?

How is the Voice>User>Speed Dial Settings number accessed from a phone keyboard?
Is the field in the settings page a dial plan string?
Unlike the Selective Call Forward Settings entires, this field seems to only accept a phone number or URL.
As such, I'm not sure how to access it from the phone keyboard.

Hi Gary,
Once configured, you should just have to press n then # - where n is the speed dial index (2 - 9).
Regards,
Andy

Analog Dial-up access with RSA

I have few question about it,
1) Is it required ACS to cisco to work with RSA ?
2) Any link to good document ?
Thank a lot

Thank for your answer paddy,
so the dial-up user will be use
user: username
password: rsa generated ?????
this is only scenario ?
Thank a lot,
Nattawut

Dial up access crashes after SB Audigy 2Zs installat

My Audigy 2ZS sound card seems to work fine, although I'm just starting to explore the options.
My problem is that since I installed this product, I experience a hard crash (blue screen) whenever I try
to go online. I only have dial-up, but both aol and my other ISP show the same behavior. When I try to go on line, the system crashes.
Any suggestions? I need both sound and internet.

This absolutely sounds like a resource conflict to me. Try installing your Audigy 2 ZS into a different PCI slot. That will probably fix it.
Good luck :robothappy:

Portugal Skype-to-Go dial-in access #

Skype will not allow me to add my Portugal mobile number (it demands that my number is a USA number). Without being able to enter this, I'm unable to find out what the number in Portugal is that I need to dial to get onto the Skype network. Can anybody help me with this? Thanks!

Could you please send me your portuguese mobile number in a private message and we can look into this. Thanks.

Dial In Access not working using ASA5510

Can somebody help me using a US robotics modem with ASA 5510. I've tried following the instruction in this link
http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807955c1.shtml but it didn't work out. After applying the string "ATE0Q1&W" nothing happen. Thanks in advance.

Hi,
I feel the pdf at the link is quite descriptive & clear to develop a sample International WD application.
But here I will try to throw some light to the concept & verifications.
Initially, you create application with english texts (some raw xlfs get created corresponding to it).
You copy & rename them to language xlfs (*_de.xlf for German language).
But these xlfs still contain texts, etc info in english so you use S2X Editor to change the texts to German language & the source language to de. You can verify this by opening the *_de.xlf file in some text editor (notepad/textpad/...) and checking this attribute value.
In WD Explorer, Reload the project, do Rebuild, DC build, Create archive (you can delete existing ear file before this), Deploy New Archive & Run the application (you have already changed IE Browser settings for German)
Kind Regards,
Nitin

IC WebClient Dial-Up access

Similar Messages

Maybe you are looking for