ICloud linked to my iPhone5 freezing issues. Anyone else?

I have a new iphone5 purchased from apple and have noticed since day one a problem with freezing on the device sporadically on the lockscreen. Only solution is to leave for 3-5 minutes or hard reset. It's frustrating as ****. Iv tried to restore iPhone via iTunes and it worked for a while then went back to normal. I realised after extensive testing turning iCloud backup ia the culprit in my case. As soon as its off no issues. Momment I turn back on it does. The other idea is to wipe device and setup as new device but OMG I don't want to go down that route as it will take me an entire day to setup as per my liking. Any advice?

I have had a similar problem that only happens though when I am on a phone call.   Between 8-10 minutes into a call the phone freezes and drops the call.  I cannot do ANYTHING for about 45 seconds while it says CALL ENDING.  I cannot use the phone at all and if anyone tries to call me it goes straight to VM.  I am on my 3rd iPhone 5 now due to this issue and another issue of a bad speaker.  I have restored, restarted, spent hours setting it up as a brand new phone all for not.  It still drops the call and freezes.  Makes me so mad. I wonder if the iCloud fix would do anything for my issue
****Bummer, I just looked at my phone and I dont even have the iCloud backup isnt even on.

Similar Messages

  • Hallo I can not activate icloud  backup on my iphone5. Can anyone help?  Thanks

    Hallo I can not activate icloud  backup on my iphone5. Can anyone help?  Thanks

    http://support.apple.com/kb/TI74
    http://support.apple.com/kb/TS4036
    Peace, Clyde

  • HT4623 Some inbound callers get the message "unavailable number" , or "call cannot be completed as dialed"  message on my new iPhone5. Has anyone else had this problem?

    Some inbound callers receive the message "call cannot be completed as dialed" , "unavailable number", or "non-working number" when trying to call on my iPhone5. Has anyone else experienced this, and what was solution? AT&T  is my carrier, they have network engrs. working on it, but no fix yet. Had problem since day one of phone receipt, Apple has replaced phone once, same problem.

    You could be having a drive collision with another device on your computer. Connect your Shuffle to a rear port on your computer, then connect your keyboard and mouse. Disconnect ALL other USB devices including printers, thumb drives, scanners, modems, digital cameras, external hard drives, infinite improbability drives, etc. If you are on a network, disconnect from the network.
    Now change the drive letter on your iPod. Use something much higher like M or P or Z, unless you have another device that uses this letter:
    http://docs.info.apple.com/article.html?artnum=93499

  • When connected to my Ford Mondeo, my ipod nano can be controlled through interface.  But after while it comes up with message 'loading data' and then freezes.  Anyone else got the issue?

    When connected to my new Ford Mondeo, my ipod nano can be controlled through user interface in car.  This worksd most of the time, but after a while if I try to change the music or search, it comes up with message 'Loading Data'.  I then have to pull out USB and reinseert, at which point it works again.  Has anyone esle expereinced this/have a solution?

    Does not matter if anyone else has this issue.  You need to contact the Ford dealership.  It's their product you are having problems with. 
    If you really want to know if anyone else has this issue, post on Ford's Mondeo message boards.  It's where the Ford car owners hang out.

  • Motherboard ground/short against case = Freeze? Anyone else?

    Hey all
    Recently, my iBook started randomly completely locking up, either before it even POSTS, or after it starts up. Like, complete freeze, everything on the screen stops, including mouse (If there even is anything on the screen).
    I had no idea what the issue was, since it seemed to be caused by slight tilt or movement, so I opened it up. While runnign it with all of hte bottom case removed (Bottom of board exposed on to desk) it worked just fine. So I put only the plastic part of the case back on, not the metal one that lies between the plastic and the board, and now, it seems to work just fine still...
    Curious... Has anyone else had this issue before? Was it really the metal casing within? Or perhaps something else that somehow got corrected when opening it?

    Nvm, it's not *completely* fixed. It's still doing it, but it's doing it much less at least... So it must have done something to help it it seems. Anyone have any idea what could be causing this issue?

  • AEBS disconnecting/dropping iMac connection issues, anyone else?

    my intel iMac 20" keeps dropping the wireless connection to my Airport. I have my MacBook Pro right beside it and its a solid connection. I called Apple tech support today, but they are closed due to Holiday in Canada.
    Anyone else having these issues with the new iMac's. So many problems lately, wireless, freezing etc.. I don't know what to do. I reformatted my iMac to see if that new update 1.1 was the issue, but it still disconnects.
    THanks

    Tried the first several times.
    Unistalling CC Desktop didn't help either.
    Tried viewing the install logs as per this page:
    http://helpx.adobe.com/creative-suite/kb/troubleshoot-install-logs-cs5-cs5.html
    Nothing.

  • IMac Sleep issues  -- anyone else ??

    I noticed there was some kind of recall for sleep/wake-up issues with the MacBook (pro?) but not the iMac. I've been having the following go on since I got my iMac about a month ago:
    Intermittently wakes up from sleep -- sometimes when I'm in the same room reading, sometimes if I put it to sleep at night it is on when I get up in the morning.
    Often, but not always, it wakes up when I pick up the phone to make a call. The system is connected (through an Apple USB modem) to a two-input phone jack, shared with my phone.
    Sometimes when I put it to sleep the screen just dims and the system locks up, necessitating a hard power-off.
    Sometimes when the system is asleep, I am unable to wake it, necessitating a hard power-off.
    I plan on bringing it in to the Apple Store one of these days, but I'm curious if anyone else is having similar problems...

    HI there,
    Try this first before taking in, reset the SMC on your machine:
    http://docs.info.apple.com/article.html?artnum=303446
    Plus, check to see if you have the latest SMC FirmWare update:
    http://docs.info.apple.com/article.html?artnum=303725
    Read but proceed with caution! Have a nice day...
    Rick
    iMac G5 iSight 20" - 30G iPOD in Slimming Black - Mac OS X (10.4.7) - HP Pav 15" WS and Toshiba Sat 17" WS LP's - Canon 20D & A620

  • New Kensington Pilotboard wireless desktop - numerous issues Anyone else??

    I just got a G4 500 AGP and also picked up a new Kensington Pilot Board wireless desktop on sale at Compxxx and it has given me fits and was wondering if anyone else had similar issues??
    Here is what I have going on :
    1) Random keys not responding at all mostly towards right side of keyboard
    2) MASSIVE system slowdown which seemed to go away after going back to a generic keyboard/mouse that are wired
    3) Horrible lag when typing and I am not a fast typer by ANY standards
    I put 2 new and fresh sets of batteries in both keyboard and mouse and re-synched about 10 times and restarted several times and un-installed and re-installed software as well with same problems persisting. Is this just a junk product or did I get a lemon??

    Tim, welcome, I have the same keyboard and it work just fine. And yes, new batteries really make a huge difference. Try Repairing Permissions and see if that solves the issue. Also if the USB cable is plug into a PCI card move it to one of the computer outlets and try moving the censor to a new location.
    The tracking speed of the mouse can be adjusted but this should not effect the OS performance at all.
    Joe
    Power Mac G4 Gigabit Ethernet   Mac OS X (10.3.9)   1.5 GB Ram, ENCORE/ST G4, Tempo SATA, ATI Radeon 9000, Adaptec 4000

  • Lacie external FW Issue, anyone else?

    Just purchased a 160g external firewire Lacie "F A Porsche" dirve. The drive will not mount to any of my G4s (Dual 800 + PowerBook). Dual 800 10.4.8, Laptop 10.4.7.
    I have verified the Lacie mounts properly to an iMac G5, a single processor Intel and a dual core Intel.
    Lacie tech support suggested I try their D2. Anyone else had issues with this dirve, comments on the D2?
    Thanks in advance,
    Chris

    The topic of dead FW ports shows up from time to time on Macintouch and other forums. The very (VERY) short answer seems to be that although FW is SUPPOSED to hot swapable, you do so at your peril. FW ports on a variety of models seem to go dead sometimes and, as you have discovered, the only solution (other than a motherboard swap) is a PCI card.
    I have a first generation AGP Sawtooth, have used the FW ports for years (but never to swap drives in and out) and my ports are still working.
    I probably just guaranteed their failure...
    G4    

  • Motion 3 Export Issues, Anyone Else?

    I've run into two issues after the 3.0.1 udpate...
    1. In the export dialog, when I click on the "Options..." button to tweak the export settings, nothing happens, I don't get the expanded dialog... this is happening on two of my machines.
    2. Using the "Export using Compressor..." option from the File menu doesn't do anything... doesn't launch Compressor, nothing. And again, this is happening on two of my machines, one with a brand new hard drive, fresh system install and brand new FCPS2 install.
    Anyone else have these issues?
    I also openend a project I started in 3.0.0 and now the output has bizarre random lines with strange colorings all over it... talk about frustrating. The exact project rendered before the update renders perfectly fine.

    I'm having the exact same problem right now. Exporting with compressor actually makes my system crash - before the upgrade everything was working perfectly. If I find anything out I'll be sure to post....

  • Wifi issues anyone else????? :/

    my iphone 5s isnt connecting to my 5ghz wifi anyymore its saying unable to connect why is this happening anyone else having this issue???
    i already restored my iphone and still dosent work

    I'm not having the issue, but thanks for asking.

  • I have found since updating to the new firefox that certain links no longer work. Has anyone else experienced this. It is becoming a real issue.

    For example, google search page links or links on certain web sites work in Safari but in firefox they are simply dead.
    Clicking on some google search page links takes you to a blank page or one with an error message. Links on shopping pages and credit card sites are non-responsive, for example, to download statements.

    Thanks very much for your response.
    Its worked like a charm. Still rather odd that the home button doesn't work though.
    Have a great day and appreciate the tip very much.

  • BT Infinity HTTPS connection issues- anyone else?

    Hi all.
    Any advice would be greatly appreciated.
    I have been having considerable problems with HTTPS sites over the past few months - timing out, unable to make payments online with ClickSafe - Lloyds Bank, Natwest, NEXT, National Lottery. Some HTTPS sites load eventually but usually very very slowly or time out.
    This issue is across all my devices - Macbook Pro, iPad Air, Samsung Tablet, Windows 8 Laptop, x3 iPhone 5.
    If I switch WiFi off on my iPhone I can make payments over the mobile phone network fine but as soon as I switch WiFi on the problems occur again. I took my Laptop to a friends house and used their TalkTalk Broadband and no issues, all worked fine.
    I have had 2 HH4 and now a HH5 and the problem still occurs.
    I have Changed numerous settings, undertaken numerous reboots and complete resets to no avail.
    I have enabled firewalls and disabled firewalls, changed MTU and numerous other possible fixes, but again none have worked.
    I have paid for BT Tech Expert support who have been very helpful  and always called back when they have said they would but they do not know what the problem is and are still working on it. Next call on Monday night.
    I found this very long thread starting in 2011 and ending in February 2013, where BT customers were experiencing the exact same problems in the South West of England and it turned out to be a network issue that was resolved but it does not explain how it was resolved! 
    https://community.bt.com/t5/BT-Infinity-Speed-Connection/BT-Infinity-and-https-connection-issues/td-...
    I am in Newcastle upon Tyne and would be grateful if anyone could let me know if they are having the similar problems?
    Thanks for your help.
    BT Infinity 2 - 75/16 Mbs

    To make sure that BT web help is disabled, look here.
    http://preferences.webaddresshelp.bt.com/selfcare/
    To try changing DNS server on your Windows 8 laptop, see this Microsoft note.
    http://answers.microsoft.com/en-us/windows/wiki/windows8_1-networking/how-to-change-ipv4-dns-server-...
    You can use 8.8.8.8 as they suggest, as that is Google public DNS.
    If that fixes the problem on the laptop, it would point to a problem with BTs DNS servers.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • IMac 27"  -Photoshop CS3/CS4 redraw issues-  anyone else?

    Hello Forum,
    I am a pro photographer.
    I do have the new 27", 3.06Gh, with 10.6.2.1
    When I start up CS3 or CS4, open a picture at 100%,
    and scroll within it, the borders show the "chess" pattern, and I have redraw issues.
    Any help would be appreciated.
    Thank You

    OK, sorry I didn´t follow this thread the last weeks.
    This has to change now
    I´m on 10.4.3.
    It didn´t bring ANY improvement.
    I have all updates installed, all firmware upgrades.
    My videocard is the Radeon HD 4670.
    Screen redraw is an absolute pain.
    For example, if I have a lasso istalled, or work on a layer I see no refresh, or lagged, sometimes the picture reverts to a previous state, but only in displaying the data.Once I zoom in, I can force a correct display.

  • FireWire Issues - anyone else?

    Have a PB G4, 1.67, with an Apple-repaired logic board [from Nov 08]. After latest Security updates, I have had trouble connecting either 800 or 400 FW drives. I've tried them on an iMac and iBook; both work. Tried different cables, three different drives [2 OCW, one Verbatim]. Nothing works. Wiggled cables. Used both bus and external power.
    HELP please. I don't want to spend another $350 [plus postage from UK via APO] to fix this a third time [was a refurb, used from PowerMax, they looked at logicboard once, and then I used Apple's fix it service]. The Apple repair warranty expired in Feb 09.
    I might try an $80 cardbus FW800/400 if I can find one still.
    Thanks in advance.

    Frustrating trying to get it to work .... You can zap the PRAM as well as reset the PMU anytime. At this point, if you haven't go ahead and do the PRAM and might as well do the PMU again. Reset PRAM. Note the effects are immediate, there's no advantage to waiting overnight:
    1. Shut down the computer.
    2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    3. Turn on the computer.
    4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    6. Release the keys.
    It sounds like you may have had hard drive issues that Drive Genius fixed for you. For comparison, did you run the Disk Utility disk repair after Drive Genius fixed the hard drive .. just to see if Disk Utility gives the drive a clean bill of health?
    When you ran the Apple hardware test, did you run the extended test? Do you have either of the TechTool programs available? They do similar testing to the Apple hardware test, it would be interesting to see if they also say the hardware is OK.
    You've reloaded the operating system a couple of times. Did you use the combo update to update to 10.4.11? I prefer that to letting Software Update make the updates, as sometimes it doesn't update correctly. Repair disk permissions before and after the update, too. Then run software update to pick up any other required updates.
    You've, by this time, reset PRAM and PMU, I assume the PRAM reset didn't change anything? If so, sorry, but I don't know what else you can do. At this point, I'd take it to a genius at the Apple store, and get their opinion.
    I didn't address sleep as I think you need to resolve the Firewire issue first, then see if there is a sleep problem.

Maybe you are looking for