ICloud PC install failed (drive g:/ is not valid)

Hello,
When I try to installe the ICloud Control Panel on my PC (Win 7), the install failed.
He said "Drive g:/ is not valid".
For information, my documents are on a server called g:/.
Regards.
K

Hi,
This issue is because of not following the OEDQ installation guide. When you are trying to deploy OEDQ with existing director.properties file, it tries to connect directly to the existing Databse specified in director.properties which but with new installation it will not find exixting tables.
Solution is simple just delete director.properties file and restart webserver. This will install director. Your installation will be completed after putting DB director and result details on the launchpad screen.
Regards,
Rajesh

Similar Messages

Install Failed: OS X could not be installed on your computer.

So my Macbook was bought last December 2012. It's specs should be able to run Mavericks.
I've downloaded the software already, so far so good.
When installation starts, it fails and I get this message:
"Install Failed: OS X could not be installed on your computer. OS X can't be installed on the disk because a recovery system can't be created. Visit www.apple.com/support/no-recovery to learn more"
Now it tells me to go to this page:
http://support.apple.com/kb/HT4649
Then I find the message above and tells me to go here:
http://support.apple.com/kb/TS3926
Then I try the solution in the 2nd link and still the installation fails.
Please note that I have a Windows 7 BootCamp Partition that I would as much as possible not delete or reformat as I have too many important stuff there.
Any ideas?

.Impact wrote:
Philly_Phan wrote:
.Impact wrote:
Philly_Phan wrote:
My WAG is that you have a HD space limitation. I've never used Boot Camp so bear with me. Is there any way that you could back up the contents elsewhere so that you can reformat and repartition?
I have an External Hard Drive here but it's currently being used as storage space for some of my media. Is it possible to backup to a partition of an external hard drive?
I've never done it but it should be possible. Don't forget that a "partition" acts like a real drive and it is a real drive in every sense of the word except that it shares a physical disc with another drive.
Will try that once I get home from University later. Should I back up both OS X and Bootcamp into the hard drive or just one of them? Then reinstall Mountain Lion, then install Mavericks? Did I get that right?
I don't see any reason why you need to reinstall Mountain Lion. It's been a long time since I've done any partitioning but, if I remember correctly, you can enlarge the main partition provided that there is no data in the secondary (Boot Camp) partition. If I'm correct, you'd need to first back up Boot Camp, then erase the original BC partition, then resize the partitions and finally load Mavericks.

HT1338 Install failed OS X could not be installed on your computer

when up grading I get the mesage Install failed OS X could not be installed on your computer and it will not go past the 17 min to go stage, any ideas please?

Is your mac compatible with Mountain Lion? You can check the list of compatible machines here.

Install fails 10.5 could not validate contents additional speech voices

I am trying to install 10.5 on a G5 I get the message install fails could not validate contents of the additionalspeechvoices package, is there a way to fix this?

It is a black retail retail disk,
Didnt have any troubles with installing it the first time, then the Maxtor hard drive went bad, installed it to a new drive and didnt have any troubles untill recently, but tried to reinstall again, but get the message install fails could not validate contents of the additionalspeechvoices package, now. It gets to about 4 minutes left then quits with the error message.

Install Failed. Installer could not copy the necessary support files

I replaced the hard drive in my MacBook 13ac OS X" late 2009. I am trying to reinstall th OS and applications from th CDs that came with the computer. When I start the computer and try to install the OS, it starts to install, after about 2-3 minutes I get the following message. Install Failed. Mac OS X could not be installed on your computer. The Installer could not copy the necessary support files. Click restart to restart your computer and try installing again. I have done this several times with no luck. Is the CD missing something? Is there another way to do this?

Disconnect any attached hard drives.
Boot off the disk and try running Disk Utility Repair Disk and Repair Permissions. If that is successful, try to re-install. If that doesn't work boot off the disk and use Disk Utility to erase and reformat the drive as Mac OS Extended (Journaled).

After re-installing my serial number is not valid for this product

My laptop crashed and I had to install PhE11 on another laptop. After installing it says: this serialnumber is not valid for this product.
But it is the only serialnumber I have, and I did not type it wrong. Please help.

Walked through the CC Cleaner, the log removed some things and this is the summary of warnings:
[Tue Dec 30 15:01:43 2014] *-*-*-*-*-*- ::START:: - SUMMARY OF Warnings -*-*-*-*-*-*
[Tue Dec 30 15:01:16 2014] DB does not exist at: C:\Program Files\Common Files\Adobe\caps\caps.db
[Tue Dec 30 15:01:42 2014] Warning: Failed to remove file,folder trying again
[Tue Dec 30 15:01:42 2014] Warning: Failed again to remove file,folder
[Tue Dec 30 15:01:42 2014] Warning: Failed to remove file,folder trying again
[Tue Dec 30 15:01:42 2014] Warning: Failed again to remove file,folder
[Tue Dec 30 15:01:43 2014] *-*-*-*-*-*- :: END :: - SUMMARY OF Warnings -*-*-*-*-*-*
Still cannot use my serialnumber. Should I remove and reinstall the new installed PhE11?

Upon install, error message says "key not valid in specified state?" How do I fix this?

The os I am using currently is windows vista. I attempted numerous updates only to have each one fail with the same message..."Key not valid in specified state." I tried full removal and reinstall only to get the same message. Any remedies?

For "Key not valid for use in specified state" errors try moving the folder RSA from
C:\Users\<User>\AppData\Roaming\Microsoft\Crypto\RSA to say C:\RSA (just in case there should be a need to restore it) then try installing again. This folder appears to act as a cache and should be rebuilt automatically as required.
tt2

Installation failing: "Strong name signature not valid for this assembly vslshost.exe"

Hi
My LightSwitch desktop client installation fail with the message below, but sure I cant sign vslshost.exe?
Help would be much appreciated.
OPERATION PROGRESS STATUS
* [2014/01/16 09:59:06 AM] : Activation of M:\[path removed] has started.
* [2014/01/16 09:59:06 AM] : Processing of deployment manifest has successfully completed.
* [2014/01/16 09:59:06 AM] : Installation of the application has started.
* [2014/01/16 09:59:06 AM] : Processing of application manifest has successfully completed.
* [2014/01/16 09:59:09 AM] : Found compatible runtime version 4.0.30319.
* [2014/01/16 09:59:09 AM] : Request of trust and detection of platform is complete.
ERROR DETAILS
Following errors were detected during this operation.
* [2014/01/16 09:59:09 AM] System.Deployment.Application.InvalidDeploymentException (SignatureValidation)
  - Strong name signature not valid for this assembly vslshost.exe.
  - Source: System.Deployment
  - Stack trace:
   at System.Deployment.Application.ComponentVerifier.VerifyStrongNameAssembly(String filePath, AssemblyManifest assemblyManifest)
   at System.Deployment.Application.ComponentVerifier.VerifyComponents()
   at System.Deployment.Application.DownloadManager.DownloadDependencies(SubscriptionState subState, AssemblyManifest deployManifest, AssemblyManifest appManifest, Uri sourceUriBase, String targetDirectory, String group, IDownloadNotification
notification, DownloadOptions options)
   at System.Deployment.Application.ApplicationActivator.DownloadApplication(SubscriptionState subState, ActivationDescription actDesc, Int64 transactionId, TempDirectory& downloadTemp)
   at System.Deployment.Application.ApplicationActivator.InstallApplication(SubscriptionState& subState, ActivationDescription actDesc)
   at System.Deployment.Application.ApplicationActivator.PerformDeploymentActivation(Uri activationUri, Boolean isShortcut, String textualSubId, String deploymentProviderUrlFromExtension, BrowserSettings browserSettings, String& errorPageUrl)
   at System.Deployment.Application.ApplicationActivator.ActivateDeploymentWorker(Object state)
COMPONENT STORE TRANSACTION DETAILS
No transaction information is available

Hi Gert.C
If you don't deploy your LightSwitch successfully on your side, you could follow this guide to
deploy a Three-Tier LightSwitch application.
> - Strong name signature not valid for this assembly vslshost.exe.
For this
vslshost.exe issue, our community members gives detailed explanation before.
You publish your LS App somewhere (even on your development machine) & run the setup program found in the folder that you publish to
Once the application is published, there'll be an icon in the Start Menu to run the application from. You can run the published application by clicking on the icon.
You can, but shouldn't, actually run the published application from the setup.exe file, but defintely not "vslchost.exe".
hope it helps.
Regards
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Re installed PS6, serial number is not valid

I have changed my computer and re installed PS6, but it says that my serial number is not valid for adobe cc2014, how do I know what it is valid for, and from where can I get it?

CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

Installing pse 7 serial number not valid

I was having issues with a pse 7. I uninstalled then downloaded a fresh copy from Adobe. I entered my serial number and it returned 'not a valid serial number'. But it is valid.

Thanks pwillener. I did that before. It took me to my account and there I found the serial number that exactly matches the one I found on my computer but again, PSE 7 says it is not valid. I even turned my firewall off during installation in case that was the problem.

SCCM 2012 R2 Install - SMS_NOTIFICATION_SERVER install fail - bgbisapi.msi could not install

Installed SCCM 2012 R2 Primary Site on the D: drive on a Windows 2012 R2 server. The install went as expected but when I open the Component Status, there are a number of Error messages which pertain to the failed installation of the SMS_NOTIFICATION_SERVER:
"Site Component Manager failed to install this component, because the Microsoft Installer File for this component (bgbisapi.msi) could not install."
Here is the error from BgbSetup.log:
<01/16/15 14:53:55> Installing the SMSBGB
<01/16/15 14:53:55> Passed OS version check.
<01/16/15 14:53:55> IIS Service is installed.
<01/16/15 14:53:55> SMSBGB already installed (Product Code: {A78E8003-2307-4B70-B7CD-1A07C0A31D21}). Upgrading/Reinstalling SMSBGB
<01/16/15 14:53:55> New SMSBGB is the same product code. This is a minor upgrade.
<01/16/15 14:53:55> Enabling MSI logging. bgbisapi.msi will log to D:\Program Files\Microsoft Configuration Manager\logs\bgbisapiMSI.log
<01/16/15 14:53:55> Installing D:\Program Files\Microsoft Configuration Manager\bin\x64\bgbisapi.msi REINSTALL=ALL REINSTALLMODE=vmaus CCMINSTALLDIR="D:\Program Files\SMS_CCM" CCMSERVERDATAROOT="D:\Program Files\Microsoft Configuration
Manager" USESMSPORTS=TRUE SMSPORTS=80 USESMSSSLPORTS=TRUE SMSSSLPORTS=443 USESMSSSL=TRUE SMSSSLSTATE=0 CCMENABLELOGGING=TRUE CCMLOGLEVEL=1 CCMLOGMAXSIZE=1000000 CCMLOGMAXHISTORY=1
<01/16/15 14:54:04> bgbisapi.msi exited with return code: 0
<01/16/15 14:54:04> Installation was successful.
<01/16/15 14:54:04> CTool::RegisterComPlusService: run command line: "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\RegSvcs.exe" /u "D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll"
<01/16/15 14:54:08> CTool::RegisterComPlusService: Failed to unregister D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll with .Net Fx 4.0
<01/16/15 14:54:08> CTool::RegisterComPlusService: run command line: "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\RegSvcs.exe" /extlb /tlb:"D:\Program Files\SMS_CCM\microsoft.configurationmanager.bgbserverchannel.tlb" "D:\Program
Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll"
<01/16/15 14:54:12> CTool::RegisterComPlusService: Failed to register D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll with .Net Fx 4.0
<01/16/15 14:54:12> Cannot register BGB server channel DLL D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll. Installation cannot continue.
<01/16/15 14:54:12> Fatal MSI Error - bgbisapi.msi could not be installed.
<01/16/15 14:54:12> ~RoleSetup().
<01/16/15 14:54:21> ====================================================================
From what I've read online this problem seems to be born of installing SCCm on the D: drive which throws dotNET. A few people seem to have had some luck with editing two of the dotNET files (regsvcs.exe.config and InstallUtil.exe.config) to include
the following lines:
    <runtime>
        <loadfromRemoteSources enabled="true"/>
    </runtime>
In pursuit of a fix, I took backups of both files and then made the change to regsvc.exe.config but I was unable to do the same with Installutil.exe.config (opening the file in Admin Notepad would only let me Save As...).
Can anyone suggest what the problem could be? Am I barking up the wrong tree with the config file editing? Any info/advice would be much appreciated.
Thanks!

Hi,
You could try to copy Installutil.exe.config and edit the copy-file. Then copy the edited file to replace the old file.
Reference:ConfigMgr 2012 R2 – Notification Server Install Errors
Note: Microsoft provides third-party contact information
to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Best Regards,
Joyce

SCCM 2012 - sms_notificaiton_server install fails, bgbisapi.msi could not be installed

Hi,
installed a SCCM 2012 R2 Primary site on a 2012 R2 server on the D: drive. Everything seemed to go well, however i am am now encountering issues with the SMS_NOTIFICATION_SERVER in that the site component manager is unable to install it. The status message
viewer informs me that, "Site Component Manager failed to install this component, because the Microsoft Installer File for this component (bgbisapi.msi) could not install."
When i check the Bgbsetup.log, i see the following lines:
<01/19/15 14:46:27> CTool::RegisterComPlusService: Failed to unregister D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll with .Net Fx 4.0
<01/19/15 14:46:27> CTool::RegisterComPlusService: run command line: "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\RegSvcs.exe" /extlb /tlb:"D:\Program Files\SMS_CCM\microsoft.configurationmanager.bgbserverchannel.tlb" "D:\Program
Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll"
<01/19/15 14:46:30> CTool::RegisterComPlusService: Failed to register D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll with .Net Fx 4.0
<01/19/15 14:46:30> Cannot register BGB server channel DLL D:\Program Files\Microsoft Configuration Manager\bin\x64\microsoft.configurationmanager.bgbserverchannel.dll. Installation cannot continue.
<01/19/15 14:46:30> Fatal MSI Error - bgbisapi.msi could not be installed.
Having done a bit of reading, it seems a few other people have come accross this issue before:
https://rikkoss.wordpress.com/2013/12/11/tip-do-not-change-the-default-installation-location-for-configmgr-2012/
http://www.windows-noob.com/forums/index.php?/topic/7401-sms-notification-server-failed-critical-sccm-sp1-sql-2012-sp1/
The solution for these folks seems to be to edit 2 files in the .Net folder,InstallUtil.exe.config and Regsvc.exe.config,
and insert the following code:
<runtime>
<loadFromRemoteSources enabled=”true”/>
</runtime>
However, this hasn't worked for me and i'm still getting stuck with the same error messages. Since i'd really like to avoid reinstalling SCCM on the C: drive, can anyone suggest any possible solutions to this issue?

The MPsetup.log has this:
<01/20/15 16:28:11> ======== Completed Installation of Pre Reqs for Role SMSMP ========
<01/20/15 16:28:11> Installing the SMSMP
<01/20/15 16:28:11> Passed OS version check.
<01/20/15 16:28:11> IIS Service is installed.
<01/20/15 16:28:11> No versions of SMSMP are installed. Installing new SMSMP.
<01/20/15 16:28:11> Enabling MSI logging. mp.msi will log to D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log
<01/20/15 16:28:11> Installing D:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi CCMINSTALLDIR="D:\Program Files\SMS_CCM" CCMSERVERDATAROOT="D:\Program Files\Microsoft Configuration Manager" USESMSPORTS=TRUE SMSPORTS=80
USESMSSSLPORTS=TRUE SMSSSLPORTS=443 USESMSSSL=TRUE SMSSSLSTATE=0 CCMENABLELOGGING=TRUE CCMLOGLEVEL=1 CCMLOGMAXSIZE=1000000 CCMLOGMAXHISTORY=1
<01/20/15 16:28:12> mp.msi exited with return code: 1603
<01/20/15 16:28:12> Backing up D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log to D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log.LastError
<01/20/15 16:28:12> Fatal MSI Error - mp.msi could not be installed.
and the MPmsi.log has this:
MSI (s) (B0:E0) [16:37:14:660]: Invoking remote custom action. DLL: C:\WINDOWS\Installer\MSI23F6.tmp, Entrypoint: CcmRegisterPerfCounters
[16:37:14] @@ERR:25001
Internal Error 25001. 80070057
MSI (s) (B0!F8) [16:37:14:676]: Product: BGB http proxy -- Internal Error 25001. 80070057
CustomAction CcmRegisterPerfCounters returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
Had a go at removing the MP, disabled the UAC and reinstalling the MP. Same result unfortunately...The server is temporarily housed in a block GPO OU so group policy shouldn't be an issue. Thanks for all the help so far!

Failing Drive - Disk Utility not working either

Recently my drive started failing to the point that it was clear that I needed to do some maintenance.
I'm backed up to an external HD, so I wasn't too worried about saving the image - just wanted to get up and running again. I started by trying to use the repair functions under the First Aid tabs. This would run for a while and error out a little less than 1/2 way through.
Because I didn't care about saving the data, I decided I'd got through the erase and reinstall process. The erase seemed to work ok, but reinstalling would fail. I tried this process 3 times and wasn't able to install correctly.
This morning, I decided to try and really wipe the drive using the "Zero Out" function. That process has been running for about 3 hours thus far and seems to have frozen at about 1/20 complete (that is - on the progress bar, 1/20 is blue while the rest remains white.) It hasn't moved in about 2 hours.
Any thoughts on next steps for:
a) What to do about this freeze
b) Assuming I can get out of the freeze how to proceed?
thanks
(oh, and I'm not certain about the OS version - it's what came with the computer (15 inch G4) but I can't eject the disk as the computer thinks it's still mid-process.

Hi there - thanks for the quick responses. Since I started looking through these post, I've been amazed at the community.
First, I think that you may be correct and the zero out is moving, albiet glacially. I put a sticker on the screen to mark progress and it seems to have done something (although, at this point, it could be an optical illusion.) I'd guess that it's closer to 1/10 done now after 8 hours.
My computer was exhibiting strange behavior - and the annoying (constant beachball) became the very annoying (would boot only every 3rd time, sometimes not at all) to the unusable (upon boot - PANIC! error.)
I backed up to a LaCie external drive using the included "Silverkeeper" SW. I am not familiar with the restore procedure, but had the idea once the computer started booting into PANIC! (probably a bad idea) that I'd use the fix utility and if not just start with a clean slate and go again.
As for the specific questions asked -
I did not run S.M.A.R.T. (and am not sure what it is)
I did not run a HW test.
Thanks,
Stephen

Stand alone APEX listener install fails with timezone region not found

Hi,
I have searched the forum but found only a thread for the installation with Goldfish.
I am very new to all this so I apologise if my problem is too simple, but please help as I am very frustrated with it.
I have a 10.2.0.4 database on Windows XP for testing with.
I installed APEX into it successfully, then down loaded the listener.
I have to Java installations, one under my Oracle Home, the other under Middleware where I have JDeveloper installed.
If I try $ORACLE_HOME/jdk/bin/java -jar apex.war it throws a Unsupported class version so I tried with the Middleware jdk and it appeared to install.
I then went to http://localhost:8080/apex/listenerConfigure and entered the password for APEX_PUBLIC_USER and the info for a basic connection, it fails with the following message
Request could not be processed due to error:
Sat Apr 30 00:06:30 CAT 2011
ORA-00604: error occurred at recursive SQL level 1
ORA-01882: timezone region not found
Please if anyone can help me through asap this I would be most grateful

Yay, I found the solution:
I started by running:
begin
for v_rec in (select tzname,tz_offset(tzname) v_offset from v$timezone_names
where tzabbrev='CAT') loop
dbms_output.put_line('tzname '||v_rec.tzname||', offset '|| v_rec.v_offset);
end loop;
end;
SQL> /
tzname Africa/Khartoum, offset +03:00
tzname Africa/Windhoek, offset +01:00
tzname America/Anchorage, offset -08:00
tzname US/Alaska, offset -08:00
PL/SQL procedure successfully completed.
I then added -Duser.timezone="+01:00" before the apex.war ie
java –jar -Duser.timezone="+01:00" apex.war

SQL 2012 install fails with 'Object reference not set to an instance of an object" On windows 8.1 Hyper-V

Hi All,
Could you please help me here? On my Laptop which is running on windows 8.1 Operation system, I enabled the Hyper-V client feature and setup the Windows Fail-over Clustering using Windows 2012 Standard Edition. So, there are three machines which are running
on the Hyper-V. Below are the machine details;
1st machine - Working as Domain controller and its name is "ACONDomainGroup" and allocated to
1GB RAM to use.
2nd machine - Working as Node1 and its name is "AconNODE1W2K12STD"
and allocated to 2.5GB RAM to use.
3rd machine - Working as Node1 and its name is "AconNODE1W2K12STD"
and allocated to 1.5GB RAM to use.
and the windows virtual cluster name is "AconWinCLTR". While I am doing the SQL Cluster Installation, I am getting below mentioned error. all systems have 4.5 .net installed. May you please guide me where and what i am missing to complete sql clustering.....
Update Source: MU
User Input Settings:
ACTION: InstallFailoverCluster
AGTDOMAINGROUP: <empty>
AGTSVCACCOUNT: <empty>
AGTSVCPASSWORD: <empty>
ASBACKUPDIR: Backup
ASCOLLATION: Latin1_General_CI_AS
ASCONFIGDIR: Config
ASDATADIR: Data
ASLOGDIR: Log
ASPROVIDERMSOLAP: 1
ASSERVERMODE: MULTIDIMENSIONAL
ASSVCACCOUNT: <empty>
ASSVCPASSWORD: <empty>
ASSVCSTARTUPTYPE: Automatic
ASSYSADMINACCOUNTS: <empty>
ASTEMPDIR: Temp
COMMFABRICENCRYPTION: 0
COMMFABRICNETWORKLEVEL: 0
COMMFABRICPORT: 0
CONFIGURATIONFILE:
ENU: true
ERRORREPORTING: false
FAILOVERCLUSTERDISKS: <empty>
FAILOVERCLUSTERGROUP:
FAILOVERCLUSTERIPADDRESSES: <empty>
FAILOVERCLUSTERNETWORKNAME: <empty>
FEATURES:
FILESTREAMLEVEL: 0
FILESTREAMSHARENAME: <empty>
FTSVCACCOUNT: <empty>
FTSVCPASSWORD: <empty>
HELP: false
IACCEPTSQLSERVERLICENSETERMS: false
INDICATEPROGRESS: false
INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL
Server\
INSTALLSHAREDWOWDIR: C:\Program Files (x86)\Microsoft SQL Server\
INSTALLSQLDATADIR: <empty>
INSTANCEDIR: C:\Program Files\Microsoft
SQL Server\
INSTANCEID: <empty>
INSTANCENAME: <empty>
ISSVCACCOUNT: NT AUTHORITY\Network
Service
ISSVCPASSWORD: <empty>
ISSVCSTARTUPTYPE: Automatic
MATRIXCMBRICKCOMMPORT: 0
MATRIXCMSERVERNAME: <empty>
MATRIXNAME: <empty>
PID: *****
QUIET: false
QUIETSIMPLE: false
RSINSTALLMODE: DefaultNativeMode
RSSHPINSTALLMODE: DefaultSharePointMode
RSSVCACCOUNT: <empty>
RSSVCPASSWORD: <empty>
RSSVCSTARTUPTYPE: Automatic
SAPWD: <empty>
SECURITYMODE: <empty>
SQLBACKUPDIR: <empty>
SQLCOLLATION: SQL_Latin1_General_CP1_CI_AS
SQLSVCACCOUNT: <empty>
SQLSVCPASSWORD: <empty>
SQLSYSADMINACCOUNTS: <empty>
SQLTEMPDBDIR: <empty>
SQLTEMPDBLOGDIR: <empty>
SQLUSERDBDIR: <empty>
SQLUSERDBLOGDIR: <empty>
SQMREPORTING: false
UIMODE: Normal
UpdateEnabled: true
UpdateSource: MU
X86: false
Configuration file: C:\Program Files\Microsoft SQL Server\110\Setup
Bootstrap\Log\20140420_052344\ConfigurationFile.ini
Rules with failures:
Global rules:
There are no scenario-specific rules.
Rules report file: C:\Program Files\Microsoft SQL Server\110\Setup
Bootstrap\Log\20140420_052344\SystemConfigurationCheck_Report.htm
Exception summary:
The following is an exception stack listing the exceptions in outermost to innermost order
Inner exceptions are being indented
Exception type: System.NullReferenceException
Message:
Object reference not set to an instance of an object.
HResult : 0x80004003
Data:
HelpLink.EvtType = 0x9AF1AE5E@0x44A889F9
DisableWatson = true
Stack:
at Microsoft.SqlServer.Configuration.RulesEngineExtension.RulesEngine.ShouldRuleRun(Rule
rule)
at Microsoft.SqlServer.Configuration.RulesEngineExtension.RulesEngine.IsRuleSkipped(Rule
rule)
at Microsoft.SqlServer.Configuration.RulesEngineExtension.RulesEngine.LoadRule(String
ruleId, List`1 ruleProperties, XmlSchema ruleSchema, XmlElementParserFactory elementParser)
at Microsoft.SqlServer.Configuration.RulesEngineExtension.RulesEngine.LoadRules(IEnumerable`1
ruleIds)
at Microsoft.SqlServer.Configuration.InstallWizard.RunRuleProgressController.Initialize()

Dharmendra, the log details are incomplete are not sufficient enough for I guess anyone to help. Besides, from the details above, I can see that the Failover Cluster Disks are not selected:-
FAILOVERCLUSTERDISKS: <empty>
FAILOVERCLUSTERGROUP:
FAILOVERCLUSTERIPADDRESSES: <empty>
FAILOVERCLUSTERNETWORKNAME: <empty>
Please mark the answer as helpful if i have answered your query. Thanks and Regards, Kartar Rana

ICloud PC install failed (drive g:/ is not valid)

Similar Messages

Maybe you are looking for