ICMP errors between WS-C3750-48P and N77-C7706 via GLC-SX-MM

Hi all,
I see ICMP packet drops between WS-C3750-48P and N77-C7706 via 1G (GLC-SX-MMD).
Regards,
Mansoor

Thanks. I've swapped GBICs/cables at both ends and it is the same result.
I've found an interesting thread.
https://supportforums.cisco.com/document/59621/icmpping-drops-when-pinging-nexus-7000
Now I'm unable to modify the class-map, I think I might need to use a lenient service-policy or copy the existing policy and apply the modified policy-map.
Any thoughts?
NX-OS version 6.2(8a).

Similar Messages

RFC connection error between BW 3.5 and ECC 6.0

Hi gurus,
We've defined an RFC destination between BW 3.5 and ECC 6.0. Connection test (SM59) is ok, but authorization one fails and ALEREMOTE users block. These users on both systems have good profiles. We look ST22 and find a runtime error on CALL_FUNCTION_REMOTE_ERROR. We've cleaned source system on BW and RFC destination and we've created one more time, but error doesn't disappear. We've looked OSS but don't find anything.
Any idea? Is there any other place (users, RFC) where we have to change user password on system?
Thanks a lot!
Regards,
Iván.
Edited by: Iván Cabezas Castillo on Nov 6, 2009 12:09 PM

Solved!
This is because of the incompatibility of password handling between
640 and 700 systems.
We have to use a maximum 8 character long password with only capital letters (numbers are also allowed) for the user "ALEREMOTE".
1. Change the password for the user in SAP R/3.
2. Maintain the password in SAP BW for the RFC destination (transaction SM59 - Logon/Security tab)
3. Authorization test is now successful.
(SM59 - Test - Authorization).
Regards!

Errors between Mail 5 inbox and Server inbox on the Exchange Server

Hi,
I upgraded to Lion recently and it seems that the Mail application struggles with the Exchange interface (although it was already the case for Snow Leopard).
Bottom line there are some email messages in my Mail inbox, which in principle mirrors the inbox on the Exchange server, which are not on the server anymore but still appears in the Inbox. The main problems is if I want to delete such message, I get an error message saying the the "message can nto be moved to Trash". Logically, since it is not on the server it is by extension not in the inbox, but it seems that a duplicate of messages gets stuck in the Mail application. Problem is that now they can;t be moved.
I restarted the application to restart the synchornisation, and still messages appears on my Mac but do not exists even on the server.
Has anyone has tips on how to get rid of these emails?
Thanks in advance

Hello Nirav,
-> This question has to be posted at MAXDB/liveCache forum &
     I saw that you already created the thread for the correct forum::
      Re: Problem in connection between SCM 5.0 and LiveCache(Both on different H
-> As SAP customer you have option to create the SAP ticket,
     we could logon to your system , check the issue & help you with
     the solution.
Thank you and best regards, Natalia Khlopina

Connection Errors between Oracle 8 Client and Oracle 8.1.6 EE

Our current application has been developed using PowerBuilder 6.5 and Oracle 8.1.5. Since PB 6.5 does not have a "native driver" for 8.1.5, we have used their driver for Oracle 8.0.5 for Net8 connectivity to the server. Everything works fine.
Recently, I downloaded the current version of Oracle 8.1.6 EE from Technet to try out the compatibilty of our software with the next version of 8I, it failed. The error seems to be somewhere between the 8.0.5 Oracle Client Software and the downloaded Oracle 8.1.6 EE Server software. Some how we have lost the ability to declare cursors. I tried declaring a cursor in a procedure through SQL*Plus and it failed their as well. I have even tried the Oracle 8.0.6 Client, with same results.
Has anyone seen this? If so, what should I do?
Thanks,
Jason

HOW TO SUPPORT TWO-TASK COMMON ERRORS - 1012295.102
Troubleshooting
===============
Two-task common errors are generally RDBMS related issues, but could be caused by a problem with SQL*Net, or an application (i.e. Pro*C).
ORA-03106
======== Possible reasons for the ORA-03106 errors include:
1. Incompatibilities between the client application and the RDBMS server.
For example, version incompatibilities, or a client trying to use a feature not supported by the database kernel.
2. When using database links or gateways.
3. Network or SQL*Net problems.
4. Corruptions.
5. PL/SQL - language related.
check the NLS_LANG variable on the client and server.

RFC connection error between Netweaver 7 EHP1 and Ides ECC6

Hi Friends,
I try to create source system in BI from Netwever EHP1 to IDES ECC6 EHP3.
During the creation I get a connection error, says. check connction parameter.
I checked the parameter, everything is fine. Server, System and number.
When I went to the SM59 and created a connction.
I.E. with the same parameter like system = 06 and server = compi9 gave client 800 etc.
The Host name is resolved to 192.168.2.111 wich is OK.
But when I run the connection test it shows me "ERROR: partner '80.156.86.78:sapgw06' not reached"
I have no idea where this IP '80.156.86.78" is comming from.
No Problem with the opposite way, from Ides to NW and login to the System is OK too.
Can anybody help me with this problem.
RG. Jimbob

Hi,
What is the next screen that comes up when you click on remote logon.
If no screen comes up then:
Check the user type of the user id used for this RFC.
It should be either dialog or service user for able to remote login.
If it open a new window and asks for password, then its excatly password issue.
Also make sure that the password is in numeric and correct.
Also make sure that the current user check box is unchecked.
Even if it dosent work, delete the connection and create again.
Please award points if helps.
Thanks
Santhosh

File Transfer Error Between Ichat 2.1 and Ichat 3

I am trying to send my brother some files. He has an Ibook G4 and so do I. He is running Ichat 3 on Tiger and I am running Ichat 2.1. Both of us are using a wireless connection through our own personal cable modems. He can send me files and I can accept them and get them without problems. Every time I try to send him a file, before it starts, we get an error 'File Transfer Error' file name not transferred.
He says he has no problems receiving files from other buddies of all different types of operating systems.
I don't recall having any problems sending or receiving from any of my other buddies either.
Is this just an OS X.3 vs OS X.4 issue? Or is there something weird with my Ibook?
Has anyone else had this problem? Thanks,
-Chris
IBook G4 1 Ghz Mac OS X (10.3.9) 640 MB RAM

Hi cjmagnuss,
Can your brother send files to other people.
It sounds like it might be his end.
File Transfers happen on Port 5190 on the UDP protocol.
Some modems and router have problems if they have to list Protocols when Port Forwading.
Is this the case for him ?
10:00 AM Tuesday; February 21, 2006
iChat Resouce Web pages

Rounding off error between stock transport order and GR (Quantity)

Hello,
I would appreciate your help in an issue. Our customer uses stock transfer order in which a conversion rule was set. Since the transport company requires another unit, the purchase order is created in ton but MIGO is done with Megawatt Hour. SAP takes into consideration only three digits after comma. Therefore, a rounding off error occurs which can only be seen in MB52 but not in the transitsaldo MB5T. The difference or the missing quantity (i.e. 0,001 MH which is 0,0000xxx TON) can not be found and thus a GR can not be posted in MIGO either.
If you have any idea how to solve this or if there is any OSS message on this, please post on this thread. I am waiting for your comments.
Thanks,
Esra

Hi Ram Prasad,
The note you suggested is very useful. I need to download the correction. When I use movement types
557/558, I got the error that the transit saldo exceeded xxx MWH.
PO = TON
GI = 2,159 MWH
GR = 2,157 MWH which corresponds to 0,459 TON
Conversion rule= 1 TON = 4,7 MWH
Do you know how to book 0,002 MWH away with these scrapping mov.types? This quantity is missing and is not shown in MB5T because this list functions with TON as far as I figured it out.
Thanks a lot for your help.
Esra Nilsson

Sync error between mail on .mac and on mail

I just got an iPod Touch, and when I connect it the sync program starts. The only issue I have is a conflict between my email accounts on .mac and mail. I have selected the one I want to use for the correct account information, but it does not save the information (regardless which one I choose). When I try to change the mail account on my computer the changes don't save. I assumed the settings would transfer to .mac, but apparently not and I can't find where to make the changes. Thanks.

iSync is only for syncing Contacts and Calendars to non-Apple mobile phones. You'd be better off asking in the MobileMe iPod touch Mail forums here:
http://discussions.apple.com/forum.jspa?forumID=1198

Is there a significant compatibility error between iTunes 10.3 and Windows 7?

My computer has locked up several times now while running iTunes 10.3 on my pc that has windows 7 on it. This problem doesn't occur anytime other than when I'm running iTunes. I feel like that suggests that iTunes is the source of this problem. Is Apple aware of this possible bug and are they doing anything to fix it? I'd like to know so I can safely run my system with iTunes again and not worry about a system freeze up or crash.

This might be helpful: http://support.apple.com/kb/TS1717
But you could also easily use iCloud (if you are syncing Keynote to icloud) by uploading from here: www.icloud.com
or us another cloud servcie such as dropBox.

Maximize Code Reuse Between Windows Phone 8 and Windows 8(via Microsoft Dev Center)

Win8 App Developers: Picked this up on the Microsoft Dev site..great tips for reusing code between your Windows 8 app and Windows Phone.
Summary: In this section, we will help you make the right choices to maximize code reuse in your apps. As a developer, you want to streamline your development and make maintaining your apps as efficient as possible. By working smarter, you give yourself more time to develop more apps and fill the marketplace with your creations. When building an app for Windows Phone 8 and Windows 8, you should look for opportunities to share code, designs, and assets as much as possible so that you maximize the return on your investment. This section describes the sharing techniques that you can use when building you app for both platforms.Read full article
LenovoDev.com Manager

Very useful! Thank you!
Jonas
Microsoft MVP: Windows Consumer Expert
Yoga Tablet 2 10 || ThinkPad X1 Carbon (20A7007MPH) || ThinkPad Helix (3698-6EU) || IdeaCentre B540
Twitter: @jonashendrickx

PI Control Error Between Process Variable and Set Point

I've developed a PI program that uses measurements from a pressure transducer as the process variable to control air pressure released from a motorized valve. The program works great at lower pressures, but as the set point pressure increases the error between the process variable and set point increases. I've tried several things....adjusting the P seems to initially increase the overshoot but the process variable always settles down below the set point....tried adjusting the EGU min and max values but no real pattern develops with this. It appears as the process variable get closer to the max EGU value of 70000 pascals the error increases.
I've attached three screen shots showing the process variable curve and setpoint value. The graph of interest is the one in the upper right hand corner.
Any recommendation or advice would be appreciated.
tks, Terry
Attachments:
Low Pressure.JPG ‏267 KB
High Pressure.JPG ‏398 KB
Mid Pressure.JPG ‏266 KB

Kyle,
First off....I appreciate your comments. No...there is no value is system represented as U16.
Actually errors start to develop quite a bit before the maximum. If you look at the mid pressure.jpg file you'll notice that the set point (~28125 Pascals) and process variable (~25625 Pascals) are roughly off by about 2500 Pascals. Then if you look at the high pressure.jpg file you'll notice that the set point (~53000 Pascals) and process variable (~45500 Pascals) are roughly off by about 7500 Pascals. Therefore it appears as the setpoint pressure increases towards maximum the error tends to increase.
I was curious about something....the set point value I'm inputting into the PID.VI , shown in the high pressure.jpg file, is from EGU to percent.VI. It would look exactly like the EGU to percent VI feeding the process variable input of the PID.VI with the set point value feeding the EGU to percent.VI input. Would I be better off feeding the actual set point value to the PID.VI input instead of percentage?
Thanks, Terry

10Gig (tengigabit) CRC Errors between N5K500 and 3750X

Dear Forum,
We have an issue with a 10 Gig connection between a Nexus 5548 and a 3750X 10Gig. There is also a HSRP group running over this link with aggressive timeouts which recently behaves somewhat unstable. We noticed a bunch of CRC errors on this link on the 3750X side (about 300 per hour) and assume that these are related to the HSRP troubles once or twice a day.
Originally the connection was made with a twinax cable. We already changed to MMF fiber with SR SFP+'s. The 10Gig Uplink Module in the 3750x has been replaced already. All to no avail. Now it's up to replace the 3750 (receives CRC) or the Nexus Chassis (sending device)
I was wondering if there is some experience on the list what is the most probably cause and solution here.
Thanks in advance,
Michael.

MTU is 1500 bytes, on both sides (I think) see output below. Strangely enough the NX has a non-zero Jumboframe counter (increasing).
C3750#sh int te3/1/1
TenGigabitEthernet3/1/1 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is 4055.3992.111d (bia 4055.3992.111d)
Description: TO_100C_PO913
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 2/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:55, output 00:00:41, output hang never
Last clearing of "show interface" counters 04:10:35
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 4011000 bits/sec, 1091 packets/sec
5 minute output rate 110431000 bits/sec, 16489 packets/sec
     37040147 packets input, 35868731879 bytes, 0 no buffer
     Received 1071851 broadcasts (935322 multicasts)
     0 runts, 0 giants, 0 throttles
     1002 input errors, 1002 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 935322 multicast, 0 pause input
     0 input packets with dribble condition detected
     182446795 packets output, 69097435882 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
C3750#sh int te4/1/1
TenGigabitEthernet4/1/1 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is 4055.39bd.001d (bia 4055.39bd.001d)
Description: TO_100D_PO913
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:14, output 00:00:33, output hang never
Last clearing of "show interface" counters 04:10:38
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 161000 bits/sec, 215 packets/sec
5 minute output rate 29493000 bits/sec, 9580 packets/sec
     3264201 packets input, 318586322 bytes, 0 no buffer
     Received 1130048 broadcasts (1020339 multicasts)
     0 runts, 0 giants, 0 throttles
     501 input errors, 501 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 1020339 multicast, 0 pause input
     0 input packets with dribble condition detected
     168673910 packets output, 87266013753 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
N5K connected to 3/1/1:
Ethernet1/1 is up
Hardware: 1000/10000 Ethernet, address: 0005.9b1f.8648 (bia 0005.9b1f.8648)
Description: CHANNEL_TO_RO015A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 3/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 2d04h
Last clearing of "show interface" counters never
30 seconds input rate 96695496 bits/sec, 16464 packets/sec
30 seconds output rate 4715024 bits/sec, 1868 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 148.33 Mbps, 20.23 Kpps; output rate 2.90 Mbps, 1.13 Kpps
RX
    26173471641 unicast packets 6446061938 multicast packets 24295222 broadcas
t packets
    32643828801 input packets 16853116460189 bytes
    7772805495 jumbo packets 0 storm suppression packets
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    48369101239 unicast packets 462061134 multicast packets 81589744 broadcast
packets
    48912752123 output packets 56533126796163 bytes
    35421478216 jumbo packets
    6 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
3 interface resets
N5K connected to 4/1/1:
Ethernet1/1 is up
Hardware: 1000/10000 Ethernet, address: 0005.9b1f.8188 (bia 0005.9b1f.8188)
Description: CHANNEL_TO_RO0015A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 2d04h
Last clearing of "show interface" counters never
30 seconds input rate 20643816 bits/sec, 10541 packets/sec
30 seconds output rate 142592 bits/sec, 180 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 25.50 Mbps, 9.49 Kpps; output rate 159.20 Kbps, 142 pps
RX
    119855915845 unicast packets 6017690609 multicast packets 20318382 broadca
st packets
    125893924837 input packets 124351081100162 bytes
    70763564145 jumbo packets 0 storm suppression packets
    0 runts 0 giants 1 CRC 0 no buffer
    1 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    20958491666 unicast packets 503446052 multicast packets 52796318 broadcast
packets
    21514734036 output packets 29748981423583 bytes
    18964491576 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
3 interface resets

Error while adding a used relationship between the New DC and the Web DC

Hi Gurus
We are getting the Error in NWDS while Adding a used relationship between the New DC and the Web DC.
Steps what we are Done
1. Create the custom project from inactiveDC's
2.creating the project for the component crm/b2b in SHRAPP_1
3.After that we changed the application.xml and given the contect path.
4.Then we tried to add Dependency to the custom create DC we are getting the error saying that illegal deppendency : the compartment sap.com_CUSTCRMPRJ_1 of DC sap.com/home/b2b_xyz(sap.com.CUSTCRMPRJ_1) must explicitly use compartment sap.com_SAP-SHRWEB_1 of DC sap.com/crm/isa/ like that it was throwing the error.
so, we skip this step and tried to create the build then it is saying that build is failed..
Please help us in this regard.
Awaiting for ur quick response...
Regards
Satish

Hi
Please Ignore my above message.
Thanks for ur Response.
After ur valuble inputs we have added the required dependencies and sucessfully created the projects, then building of the projects was also sucessfully done and EAR file was created.
We need to deploy this EAR file in CRM Application Server by using the interface NWDI.
For Deploying the EAR into NWDI, we need to check-in the activites what i have created for EAR. once i check-in the activites ,the NWDI will deploy the EAR into CRM Application Server.
In the Activity Log we are able to check the Activities as Suceeded but the Deployment column is not showing any status.
When i right click on my activity Id the deployment summery is also disabled.
So finally my Question is that where can i get the deployment log file, and where can i check the deployment status for my application..
Any pointers in this regard would be of great help..
Awaiting for ur valuble Responses..
Regards
Satish

Getting Error The trust relationship between the primary domain and the trusted domain failed in SharePoint 2010

Hi,
SharePoint 2010 Backup has been taken from production and restored through Semantic Tool in one of the server.The wepapplication of which the backup was taken is working fine.
But the problem is that the SharePoint is not working correctly.We cannot create any new webapplication ,cannot navigate to the ServiceApplications.aspx page it shows error.Even the Search and UserProfile Services of the existing Web Application is not working.Checking
the SharePoint Logs I found out the below exception
11/30/2011 12:14:53.78 WebAnalyticsService.exe (0x06D4)        0x2D24 SharePoint Foundation         Database
8u1d High    Flushing connection pool 'Data Source=urasvr139;Initial Catalog=SharePoint_Config;Integrated Security=True;Enlist=False;Connect Timeout=15'
11/30/2011 12:14:53.78 WebAnalyticsService.exe (0x06D4)        0x2D24 SharePoint Foundation         Topology
2myf Medium Enabling the configuration filesystem and memory caches.
11/30/2011 12:14:53.79 WebAnalyticsService.exe (0x06D4)        0x12AC SharePoint Foundation         Database
8u1d High    Flushing connection pool 'Data Source=urasvr139;Initial Catalog=SharePoint_Config;Integrated Security=True;Enlist=False;Connect Timeout=15'
11/30/2011 12:14:53.79 WebAnalyticsService.exe (0x06D4)        0x12AC SharePoint Foundation         Topology
2myf Medium Enabling the configuration filesystem and memory caches.
11/30/2011 12:14:55.54 mssearch.exe (0x0864)                   0x2B24 SharePoint Server Search      Propagation Manager
fo2s Medium [3b3-c-0 An] aborting all propagation tasks and propagation-owned transactions after waiting 300 seconds (0 indexes) [indexpropagator.cxx:1607] d:\office\source\search\native\ytrip\tripoli\propagation\indexpropagator.cxx
11/30/2011 12:14:55.99 OWSTIMER.EXE (0x1DF4)                   0x1994 SharePoint Foundation         Topology
75dz High    The SPPersistedObject with
Name User Profile Service Application, Id 9577a6aa-33ec-498e-b198-56651b53bf27, Parent 13e1ef7d-40c2-4bcb-906c-a080866ca9bd failed to initialize with the following error: System.SystemException: The trust relationship between the primary domain and the trusted
domain failed.       at System.Security.Principal.SecurityIdentifier.TranslateToNTAccounts(IdentityReferenceCollection sourceSids, Boolean& someFailed)     at System.Security.Principal.SecurityIdentifier.Translate(IdentityReferenceCollection
sourceSids, Type targetType, Boolean forceSuccess)     at System.Security.Principal.SecurityIdentifier.Translate(Type targetType)     at Microsoft.SharePoint.Administration.SPAce`1.get_PrincipalName()
at Microsoft.SharePoint.Administration.SPAcl`1.Add(String princip...
11/30/2011 12:14:55.99* OWSTIMER.EXE (0x1DF4)                   0x1994 SharePoint Foundation         Topology
75dz High    ...alName, String displayName, Byte[] securityIdentifier, T grantRightsMask, T denyRightsMask)     at Microsoft.SharePoint.Administration.SPAcl`1..ctor(String persistedAcl)
at Microsoft.SharePoint.Administration.SPServiceApplication.OnDeserialization()     at Microsoft.SharePoint.Administration.SPIisWebServiceApplication.OnDeserialization()     at Microsoft.SharePoint.Administration.SPPersistedObject.Initialize(ISPPersistedStoreProvider
persistedStoreProvider, Guid id, Guid parentId, String name, SPObjectStatus status, Int64 version, XmlDocument state)
11/30/2011 12:14:56.00 OWSTIMER.EXE (0x1DF4)                   0x1994 SharePoint Foundation         Topology
8xqx High    Exception in RefreshCache. Exception message :The trust relationship between the primary domain and the trusted domain failed.
11/30/2011 12:14:56.00 OWSTIMER.EXE (0x1DF4)                   0x1994 SharePoint Foundation         Timer
2n2p Monitorable The following error occured while trying to initialize the timer: System.SystemException: The trust relationship between the primary domain and the trusted domain failed.       at System.Security.Principal.SecurityIdentifier.TranslateToNTAccounts(IdentityReferenceCollection
sourceSids, Boolean& someFailed)     at System.Security.Principal.SecurityIdentifier.Translate(IdentityReferenceCollection sourceSids, Type targetType, Boolean forceSuccess)     at System.Security.Principal.SecurityIdentifier.Translate(Type
targetType)     at Microsoft.SharePoint.Administration.SPAce`1.get_PrincipalName()     at Microsoft.SharePoint.Administration.SPAcl`1.Add(String principalName, String displayName, Byte[] securityIdentifier, T grantRightsMask,
T denyRightsMask)     at Microsoft.SharePoint.Administrati...
11/30/2011 12:14:56.00* OWSTIMER.EXE (0x1DF4)                   0x1994 SharePoint Foundation         Timer
2n2p Monitorable ...on.SPAcl`1..ctor(String persistedAcl)     at Microsoft.SharePoint.Administration.SPServiceApplication.OnDeserialization()     at Microsoft.SharePoint.Administration.SPIisWebServiceApplication.OnDeserialization()
at Microsoft.SharePoint.Administration.SPPersistedObject.Initialize(ISPPersistedStoreProvider persistedStoreProvider, Guid id, Guid parentId, String name, SPObjectStatus status, Int64 version, XmlDocument state)     at Microsoft.SharePoint.Administration.SPConfigurationDatabase.GetObject(Guid
id, Guid parentId, Guid type, String name, SPObjectStatus status, Byte[] versionBuffer, String xml)     at Microsoft.SharePoint.Administration.SPConfigurationDatabase.GetObject(SqlDataReader dr)     at Microsoft.SharePoint.Administration.SPConfigurationDatabase.RefreshCache(Int64
currentVe...
Please guide me on the above issue ,this will be of great help
Thanks.

I have same error. Verified for trust , ports , cleaned up cache.. nothing has helped.
The problem is caused by User profile Synch Service:
UserProfileProperty_WCFLogging :: ProfilePropertyService.GetProfileProperties Exception: System.SystemException:
The trust relationship between the primary domain and the trusted domain failed.       at System.Security.Principal.SecurityIdentifier.TranslateToNTAccounts(IdentityReferenceCollection sourceSids,
Boolean& someFailed)     at System.Security.Principal.SecurityIdentifier.Translate(IdentityReferenceCollection sourceSids, Type targetType, Boolean forceSuccess)     at System.Security.Principal.SecurityIdentifier.Translate(Type
targetType)     at Microsoft.SharePoint.Administration.SPAce`1.get_PrincipalName()     at Microsoft.SharePoint.Administration.SPAcl`1.Add(String principalName, String displayName, SPIdentifierType identifierType, Byte[]
identifier, T grantRightsMask, T denyRigh...
08/23/2014 13:00:20.96*        w3wp.exe (0x2204)
        0x293C        SharePoint Portal Server              User Profiles
        eh0u        Unexpected        ...tsMask)     at Microsoft.SharePoint.Administration.SPAcl`1..ctor(String persistedAcl)
at Microsoft.Office.Server.Administration.UserProfileApplication.get_SerializedAdministratorAcl()     at Microsoft.Office.Server.Administration.UserProfileApplication.GetProperties()     at Microsoft.Office.Server.UserProfiles.ProfilePropertyService.GetProfileProperties()
Please let me know if you any solution found for this?
Regards,
Kunal

I updated to iTunes 12 and didn't like it. Followed advice to revert to 11.1. Now my iphone won't sync and error message says I need iTunes 11.2 or higher. Apple Download choices didn't have anything between 11.1.5 and 12. What can I do?

I updated to iTunes 12 and didn't like it. Followed advice to revert to 11.1. Now my iPhone 5 won't sync and error message says I need iTunes 11.2 or higher. Apple Download choices didn't have anything between 11.1.5 and 12. What can I do? Using iTunes 12 is not an option. Many features I used for audiobooks have disappeared.

The version immediately prior to 12 was 11.4.0.18. Here are direct download links from Apple's servers:
iTunes 11.4.0.18 for Windows (32-bit) - iTunesSetup.exe (2014-09-09)
iTunes 11.4.0.18 for Windows (64-bit) - iTunes64Setup.exe (2014-09-09)
tt2

ICMP errors between WS-C3750-48P and N77-C7706 via GLC-SX-MM

Similar Messages

Maybe you are looking for