[ID 365563 daemon.error] can't get stderr port: Cannot assign requested add

Hello friends, i m getting the messages bellow in error logs, please suggest me what i have to do
" [ID 365563 daemon.error] can't get stderr port: Cannot assign requested add"

Hi Tom,
     Thanks, but at this point, I've rebooted, checked and double-checked more times than I'd care to count...:(
     Since I can see the NMEA strings when the GPS module is hooked-up to the USB port, I guess I'll assume there's some reason why the
     AMA0 UART has not been released, or that the GPS receives some different signals through the TTY that it's not seeing through the AMA0.
      As I mentioned, when I use 'cat /dev/ttyAMA0', it just hangs, like it's getting no data. I'll keep looking...
     Thanks for your help,
          Dave

Similar Messages

Rsh[3088]: [ID 365563 daemon.error] can't get stderr port in /var/adm/mes..

Hi,
We are using Solaris 9 in our SF6900 cluster. On one of the node we are getting below continuous flow of messages. Please let me know what does these messages means and how to clear them.
root@l7n2> tail -f /var/adm/messages
Aug 8 09:09:34 l7n2 rsh[3071]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3075]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3077]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3078]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3082]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3084]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3085]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3086]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3087]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
Aug 8 09:09:34 l7n2 rsh[3088]: [ID 365563 daemon.error] can't get stderr port: Cannot assign requested address
^C
Thanks.

Hi Tom,
     Thanks, but at this point, I've rebooted, checked and double-checked more times than I'd care to count...:(
     Since I can see the NMEA strings when the GPS module is hooked-up to the USB port, I guess I'll assume there's some reason why the
     AMA0 UART has not been released, or that the GPS receives some different signals through the TTY that it's not seeing through the AMA0.
      As I mentioned, when I use 'cat /dev/ttyAMA0', it just hangs, like it's getting no data. I'll keep looking...
     Thanks for your help,
          Dave

Finder got an error: Can't get item 1 of {document file "foo" ...}

I have a lot of files in Corel Painter 8's RIFF format. I want to write a script that opens a file and somehow forces Corel Painter 8 to save the file as a GIF. GUI scripting may be some help with the latter; now I am concentrating on finding RIFF files and opening them in Corel Painter 8.
I have a script that does a depth-first search of the folders starting at some root folder, using the Finder application to do the file-system stuff. It creates a list with
set docs to every document file of pages_folder whose file type = "RIFF"
as it loops through folders it adds to the list like this:
set more_documents to every document file of a_folder whose file type = "RIFF"
set docs to docs & more_documents
My naîve mental model is that docs is a list of document-file objects. Next I have a loop that attempts to strip out files for which a GIF file already exists (and is no older than the RIFF document). This works by deleting non-matching items like so:
if not isgifneeded then
set docs to items 1 thru (i - 1) of docs & items (i + 1) thru (length of docs) of docs
end if
Finally it tries to open one of the files in Corel Painter 8 using the Finder:
open item 1 of docs using "Corel Painter 8"
This does not work. I get an error message
Finder got an error: Can't get item 1 of {document file "bar" of folder "foo" of folder "blah" of folder "pdc" of folder "Users" of startup disk, ... }."
It lists all of the files. (The error message appears in a sheet that extends off the bottom of the screen!) They are identified in the message as document-file objects. The curly braces are, I believe, the AppleScript notation for a list. I expect to be able to obtain the first element of a list with ‘item 1 of xs’. My assumption is that the Finder’s open command would expect a document file object, or at least would be able to cope with being asked to open a document. What am I missing here?
PowerBook 12" without mini-DVI Mac OS X (10.4.7)

Hi Damian and welcome to Apple Discussions!
One suggestion: try
tell application "Finder" to open item 1 of docs
(without 'using "Corel Painter 8"')
As far as the Finder is concerned, "Corel Painter 8" is just a string of characters. And telling the Finder to open a file is just the same as double-clicking it: the Finder knows which app to use - as long as these are native Corel Painter 8 docs.
Hope this helps,
H

Import Issue : "Database error: can't get path to master" when attempting to import photos (referenced method)

Hi Everyone,
I have a NAS (Network Attached Storage) which holds my photos. I want to import them into Apple photos (but via the reference method).
I did this by going to Preferences/General and unchecking the 'Importing: Copy items to the Photo library' option.
I connect to my NAS via AFP and have mount 'Media' which is where my photos are stored.
I select the file/import option, navigate to aforementioned photo location and select the "Review for import" button
I then receive an error which states:
Unreadable File
The following files could not be imported (they may be an unrecognized file type or the files may not contain valid data).
Filename Reason
Filename.jpg Database Error: can't get path to master
The above error happens on multiple file types.....
However ...
If I tick the option in the preferences/general to 'Importing : Copy items to photo library" option then the file will import successfully.
I of course don't want to import the files I want them to be referenced...
Anyone else experiencing this issue????
Thanks in advance.
Benjamin

If this is a 3rd party application, I would seek out that company and ask for an updated version compatible with 2010, then it would be a matter of simply installing it per their instructions.
Otherwise, the best course of action is to deactivate the feature from WSSv3 prior to removal. If that is no longer possible, then use
FeatureAdmin to remove the feature from within 2010.
Trevor Seward
Follow or contact me at...
&nbsp&nbsp
This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

I am trying to copy a document and I keep getting the error "Can't paste the objects. The requested transformation would make some objects fall completely off the drawing area."

I am trying to make duplicate documents with minor adjustments to each and when I try to copy the artwork from one document and paste it into the new document I keep getting the error "Can't paste the objects. The requested transformation would make some objects fall completely off the drawing area." Both documents are exactly the same size, res, color format etc. I even tried to drag and drop and get the same error message. Anyone know what I can do to resolve this issue?

Try scaling the view size down to 6% or so and then do a Select All. See if there are objects off the artboard which may be causing this error. Most often you will see this if there were guides dragged from a ruler which were selected by dragging the white arrow and then deleted. This leaves the anchor points at the edge of the work area.

IChat Error: "Can't get video from the camera"

When I try to Screen Share with iChat on a local network, I receive the error "Can't get video from the camera" when I have an external camera plugged into the FW400 port on my Mac Mini. The Screen Sharing feature works great when the camera is not connected. Anyone know why this is and how to fix it?

Tell us about the Network you created please.
What make and model modem ?
Can it route (issue IPs) ?
IS there a router ?
Make and model of that please ?
If there are two devices which is doing DHCP if any are ?
IS there any computer that is sharing it's Internet Connection with any other computer ?
I take it from the title and the post that you infer you can Video and Audio chat ?
The Cannot get Video from Camera normally gets and Error Log pop up.
This can be opened with the reveal triangle on the left. The Details shown will have a Error number. Do you know what this log says ? (normally Error 20 or 21)
Old logs are stored in Users/(your account)/Library/Logs/iChatConnectionErrors by date.
IF you post an Error Log stop at the line that Says "Binary Images for iChat" as we don't need the bits below that yet.
As the Screen share in iChat uses an Audio component then the Camera if it is also the Mic needs to be ON.
In your case this may mean that in the ichat Video Menu both Camera Enabled and Mic Enabled should both be ticked.
(I have never seen an iChat error code for not (specifically) being able to get the Mic input so the message might be the only one iChat can pop up)
It does seem very odd that it only effecting Screen Sharing.
I have a Firewire connected DV converter that has two Firewire ports itself so I can input the camera feed to two computers. When this is in place the System also sees it as a Network.
I have also heard of one person with a Firewire Stills camera and I think the Storage space was seen as an External Device and therefore appeared Networked which is why I asked the first set of questions.
iChat does not like being in Two networks (a modem that issues IP address and a router doing the same or Wireless to a neighbour and Ethernet to your Own Internet connection, the Mac being the hub in a Share Internet connection, Wireless and Ethernet to the same router and using Parallels when set to Share the Mac's IP are the most common)
The Screen Sharing option in iChat > Video Menu is ON ? (at both ends ?)
As iChat's Screen Sharing is related to the System Screen Sharing and therefore Apple Remote Desktop you may find that in any routing device you may have to open ports 5900 and 5988 if not using UPnP
http://support.apple.com/kb/TS1629?viewlocale=en_US
You said Local Network. Do you mean this is using the Bonjour Buddy List ?
11:21 AM Saturday; June 14, 2008

Applescript for mail error can't get message id

I have an applescript (found on internet) for Mail 4.5 that deletes messages in "on my mac" mailbox "Deleted Inbox" that are older than 120 days. The script runs from an iCal daily event. I drag messages from Inbox to "Deleted Inbox" when I don't want the message in Inbox, but I want to save the message for 120 days before deleting it. The script sometimes runs successfully, and sometimes gives error "Mail got an error: Can't get message id xxx of mailbox "Deleted Inbox"". Then in Mail, I "Mailbox / Rebuild" that mailbox, and run the script manually without error. How can I avoid that error? The script is essentially:
tell application "Mail"
          set OldStuff to every message of mailbox TheBox where date received of it < OldDate
          repeat with ThisMessage in OldStuff
delete ThisMessage
          end repeat
end tell
Thanks for any help.
Ken

How can I avoid that error?
I don't actually know how you can avoid that error. However, maybe you can use a workaround and have the script rebuild the mailboxes automatically when such an error occurs. Try the following code:
tell application "Mail"
try
    set OldStuff to every message of mailbox TheBox where date received of it < OldDate
on error
    activate
    tell application "System Events" to click menu item "Rebuild" of menu 1 of menu bar item "Mailbox" of menu bar 1 of process "Mail"
    delay 1 -- adjust if necessary
    set OldStuff to every message of mailbox TheBox where date received of it < OldDate
end try
repeat with ThisMessage in OldStuff
    delete ThisMessage
end repeat
end tell
Since the above script uses GUI Scripting, you must enable the Accessibility Frameworks by clicking the checkbox labeled "Enable access for assistive devices" in the Universal Access System Preference pane.
Message was edited by: Pierre L.

System Events got an error: Can't get current configuration of service?

I'm trying to connect/disconnect services through apple script, here is the error I'm getting for "Ethernet" "AirPort" (these services are configured in services tab)
I am able to manualy On/Off these services without supplying admin password, therefore it might not be privilages issue.
*Error message:*
*System Events got an error: Can’t get current configuration of service id "099F7D16-4F3A-4D49-9111-A4DF0A645378" of network preferences.*
Scipt used:
tell application "System Events"
tell network preferences
tell current location
get the name of every service
set myService to service "AirPort"
if exists myService then
--get service properties of myService
set isConnected to connected of current configuration of myService
if isConnected then
disconnect myService
repeat while (get connected of current configuration of myService)
delay 1
end repeat
end if
connect myService
end if
end tell
end tell
end tell

Hi Damian and welcome to Apple Discussions!
One suggestion: try
tell application "Finder" to open item 1 of docs
(without 'using "Corel Painter 8"')
As far as the Finder is concerned, "Corel Painter 8" is just a string of characters. And telling the Finder to open a file is just the same as double-clicking it: the Finder knows which app to use - as long as these are native Corel Painter 8 docs.
Hope this helps,
H

Can not get rid of cannot verify server identity pop up, how can i get rid of it for 3rd gerneration ipad?

how can I get rid of cannot verify server identity pop up on my new 3rd generation ipad?

A [http://www.google.com/search?q=Brookwood+Internist+Birmingham&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a Google search] shows the website, but it still doesn't load - it shows the Go-Daddy '''Want to buy this domain?''' page.
Using a DNS Lookup for that domain - http://68.178.232.100/ doesn't load that web site either. It shows '''This site is not currently available.'''
Might be a server problem where that website is hosted, a DNS problem, or an expired domain name ''(but when that happens the message is usually '''expired registration''')''.
Call your doctors office Monday morning and tell them that their website won't load. It's something that their webmaster needs to look into, along with their web hosting service ''(which I guess is Go-Daddy)''.

How can I get into my submitted podcast to add a cover graphic?

How can I get into my submitted podcast to add a cover graphic and make other modications?

You don't edit your podcast in iTunes, if that's what you are asking: it works entirely from the feed. You have to make any changes in the feed, and re-upload it. Whatever method you used to create the podcast - a program or an online service - is where you need to make any changes.
Is this your podcast -
https://itunes.apple.com/podcast/audio-sermons-at-glendale/id733032556
if so your feed is at
http://glendalecitychurch.org/index.php/component/podcastmanager/?format=raw&fee dname=1?n=100

Error starting HTTP-Server: Cannot assign requested address: JVM_Bind

Hi.
Anyone know how to configure the Oracle HTTP server within Jdeveloper9i to work?
When I try run a JSP page, I get the following error:
C:\Oracle9iDS\jdk\bin\javaw.exe -ojvm -classpath C:\Oracle9iDS\j2ee\home\oc4j.jar com.evermind.server.OC4JServer -config C:\Oracle9iDS\jdev\system\oc4j-config\server.xml
[Starting OC4J using the following ports: HTTP=8888, RMI=23891, JMS=9227.]
[waiting for the server to complete its initialization...]
Error starting HTTP-Server: Cannot assign requested address: JVM_Bind
Oracle9iAS (9.0.2.0.0) Containers for J2EE initialized
Please contact me at [email protected]
cheers paul

A JVM_Bind error means that the port is already in use. This is an unusual error message to get because JDev scans the ports ahead of time to make sure they are free before launching the server.
Check if you have any processes running that might be holding port 8888. There might be a previous instance of the OC4J server running that hasn't released port 8888 yet. On Windows, at a command prompt, you can use "netstat -a" to see local ports that are in use.

Downloaded 11.1.4.62, get R6034 error, can't get it cleared up

When opening iTunes, I was prompted to download 11.1.4.62, so I did as I normally do.
A Run time error pops up now
c\programfiles\iTunes\iTunes.exe
R6034
iTunes not installed correctly
I'm hooped, can't get iTunes installed, need help
When looking for a fix for R6034, PCHELPER360 came up, looked like a microsoft product, bought it, it did not do a thing to fix the problem.
Anyone have an answer??

Fix for R6034.
Delete/Uninstall All references to Apple in your Program Files.
1. Sort by Apple then delete/uninstall All Apple programs, not your iTunes Music thou.
2. Delete all data held in your Recycle Bin, then Reboot your computer.
3. Once the PC is up again, go into your Saved Down Loads, find the old itunes install from 9/25/13 (93,170kb) and re-install that old program, voila, up came my iTunes with no errors.
Always do a Save when installing programs, not a Run, then Run that Saved program. You then still have the old program too use.

Applescript editor error - "can't get item 1 of false" when clicking cancel to close window.

Hello
I have made my first ever app which opens a webpage, its very basic but when I click the cancel button to close the page I get an error pop up saying can't get item 1 of false. I have looked it up and tried a few suggestions but the error just changes instead of exiting the window like it should
The code looks like this, I am wondering if anyone has any suggestions on how to fix this ...
--create the dialog list
set item_list to {"Google"}
set item_selected_array to (choose from list item_list with title "Google app" with prompt "To select the webpage, select it from the list and then click Ok" cancel button name "Cancel")
set item_selected to item 1 of item_selected_array
--google
if item_selected = "google" then
          try
                    tell application "Safari" to launch
                    tell application "Safari" to activate
                    tell application "Safari" to open location "http://www.google.com"
          end try
end if
Thanks for looking and sorry if this is in the wrong section

The choose from list command will return a list of items chosen (even if there is only one) or the boolean false if the cancel button is pressed, so you just need to check for the cancel result. Since you are only selecting one item, one way would be to coerce the result to text (since you need to get the choice from the list anyay) and compare that - note that you don't need to target Safari for the open location command, since it is from Standard Additions.
set item_list to {"Google"}
set theChoice to (choose from list item_list with title "Google app" with prompt "To select the webpage, select it from the list and then click Ok" cancel button name "Cancel") as text
if theChoice is "false" then error number -128 -- cancel
if theChoice = "google" then --google
open location "http://www.google.com"
end if

Can't get a hot-key assigned to a Mail submenu

This is in 10.5.2. by the way...
I have a sub-menu of Get New Mail called "Gmail" where I fetch email from (you guessed it) my Gmail account.
In the keyboard shortcut panel I can't assign a key to this. Anything I set in the panel doesn't show up in the Mail sub-menu. I have tried restarting Mail after making the setting in the keyboard panel, but that doesn't help.
Is this possible?
Thanks,
doug

I have that same SSD that I've tried for the last 18 hours to get Lion installed via Network Recovery. In various spots along the download, it will error out and say "could not download all..." -- forget the rest of the sentence off the top of my head. But it basically says it can't finish downloading Lion. I currently have it on the 6th attempt after trying the partition resize trick as well as deleting and reformatting the drive too. So far I can't get the Lion download to actually finish.
Also, the download for Lion is incredibly slow, and it's not a network connection issue. I've tried on 3 separate ISPs with a connection speed of no less than 12 Mbps and the fastest time I've seen for a completed download based on the figure within Network Recovery is 9 hours.
I remember using Network Recovery on my mid-2011 Air to try out the (at the time) new feature and it downloaded Lion in ~3 hours max. Not sure why it's now 10+ hours for the same file I downloaded in July.

How can we get the Latest Resource Assigned in the Approval Form

I was wondering if there is any way to get the Latest Assigned Resources to a User in my Approval Form.
I tried this <ref>waveset.resourceAssignments</ref> but it returned all the Resources assigned to a User. While creating a User with Resource Assigned it won�t be problem. While Update when a User is assigned a Resource & it comes for Approval to the owner, all the Previously assigned resources shows up. How can I get only the Latest Resource Assigned.
Can anyone provide some hints on this..

idm_guy, if you could elaborate more on what you mean with latest resource assigned it would help - but there are a number of options (if i interprent you correctly to solvethis). My guess is that the easiest way would be to determine if:
waveset.accounts[<iterate through resources>].created = true or false
and if
waveset.accounts[<resource>].lastPasswordUpdate = <last updated date>
The latter is of course only applicable to resource where you set a password. This value will be updated whenever you set the password and could be a possible value to check against.
If the account is not created yet but assigned it might be another possibility to check, but again - clairfy a bit about what you mean with "Latest Resource Assigned".
/Anders

[ID 365563 daemon.error] can't get stderr port: Cannot assign requested add

Similar Messages

Maybe you are looking for