Ideapad S205 doesn't support booting from SDHC-Card

Hello,
I have the Ideapad S205 and I cannot boot from a SDHC-Card (Ubuntu Linux) with the internal cardreader. With an external card reader I can boot from the SDHC-Card.
Is there any solution or maybe a BIOS-Upgrade?
Thanks
Simon

when you see lenovo logo, press f12 to set bios order.
also, check for bios booting option. if there's not option, i don't think s205 supports booting from sdhc, but apparently it supports usb boot.

Similar Messages

Will bios boot from SDHC cards?

I'm trying to put an Arch Linux install on a 32GB SDHC card. I'm able to install the required files, but for whatever reason I can't get the SDHC card to show up in the boot menu, and UEFI doesn't seem to work. Of course, I haven't had any luck with UEFI booting on the W530 for some reason. I can get UEFI to work fine on my desktop, but no luck on the W530 from regular hard drives or my SDHC card.
Will the W530 recognize and boot from SDHC cards that have GRUB installed on them? So far I've had no luck with that. The card never shows up in the boot menu. I can't even get it to boot installer images. Booting from USB works just fine.
Solved!
Go to Solution.

The SDHC reader on thinkpads is attached to the PCI Bus. Makes for faster Read write, but kills booting from it.
W530(2436-CTO): i7-3720QM, nVidia Quadro K2000M,16GB RAM, 500 GB hard drive, 128GB mSATA SSD, Ubuntu 14.04 Gnome, Centrino Ultimate-N 6300.
Yoga 3 Pro: Intel Core-M 5Y70, Intel HD 5300, 8GB RAM, 128GB eMMC, Windows 8.1, Broadcom Wireless 802.11ac.

ZTE OPEN C boot from SD card

I have an ZTE OPEN C hardbricked into QHSUSB_BULK mode (trying to flash flame image)
Does it support boot from SD card or there is any other method for debricking?

My brick is totally bricked - there is no fastboot or adb modes. When I connect it dmesg shows
[Сб. нояб. 8 10:31:55 2014] usb 1-1: new high-speed USB device number 15 using ehci-pci
[Сб. нояб. 8 10:31:55 2014] usb 1-1: New USB device found, idVendor=05c6, idProduct=9008
[Сб. нояб. 8 10:31:55 2014] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[Сб. нояб. 8 10:31:55 2014] usb 1-1: Product: QHSUSB__BULK
[Сб. нояб. 8 10:31:55 2014] usb 1-1: Manufacturer: Qualcomm CDMA Technologies MSM
[Сб. нояб. 8 10:31:55 2014] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[Сб. нояб. 8 10:31:55 2014] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1

Solaris support booting from san ?

Does anyone know if Solaris 10 supports booting from a san fabric lun ? In particular, an IBM DS4800.
The installer doesn't see the luns when it comes time to choose a disk to install on, only the internal disks.
The server is a IBM LS20 blade. I've managed to install Sol. 10 on the internal drives and can see the luns on the DS4800.
I'm using Solaris 10 Express 10/05 x86/64.
Brian.

Do you see the luns after boot? I'm wondering if there isn't a driver for your controller in the default installation environment. I would assume one could be added (that being one of the big benefits of newboot). Especially if you could create a jumpstart server. (It's easer to add a driver to it than to burn a new CD/DVD).
Darren

Does hp dc7900 support booting from 3tb hdd?

does hp dc7900 minitower support booting from 3tb hdd?

Hi:
Probably not.
In order to be able to boot from a 3 TB HDD, you need:
1. A UEFI BIOS, which I do not believe the dc7900 has.
There is a picture (see page 5 at the link below) of the HP splash screen for an HP business desktop that has a UEFI BIOS. If your HP splash screen doesn't look like the one in the picture, then you will not be able to boot from a 3 TB HDD.
2. A GPT-formatted hard drive.
http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c02826744/c02826744.pdf
Paul

KDL-42W807B doesn't support conversion from 2D to 3D

Hi, i just bought TV model No KDL-42W807B and it doesn't support conversion from 2D to 3D and i need to play my ps4 games in 3D mode so is there is any thing can i do to let my tv convert 2d to 3d or what type of suitable converter to do this job for my ps4

Hi mohands,
The TV model you have provided appears to be not a US model and we are unable to check its specification.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
Thanks,
Jerome
If my post answers your question, please mark it as "Accept as Solution"

MSI 875P Neo-FIS2R support booting from USB devices?

I am building a super computer using the MSI 875P Neo-FIS2R. I would like to either get a USB pen drive, or an external Floppy Disk Drive in place of an internal Floppy Disk Drive.
Does anyone know if this board supports booting from a USB device?

I ordered my board as well, however, they were out of stock and it may be as long as 2 weeks before they get more in. If you don't mind me asking, where did you get yours from? I am VERY much excited about getting this board as I only await the MB and CPU. What all are you putting in yours??
Mine:
MB- Obvious
CPU- 2.4 800Mhz
RAM- 2 sticks, 256 PC 3200 XMS Corsair using dual channel, at first I think I will use the 512 pc3200 I already have though.
HDD- 80GIG W/D 7200 RPM ( May get another to run RAID 0)
VGU- Chaintech TI4200 at 8x w/ 128 DDR
CD#1- 52x cd rom
CD#2- dvd 16x, cdr 48 cdrw24 cdrom 48
500W raidmax Pwr Sup
Koolcases Panther case w/ window and 3 80MM/ 1 60MM fans
For now I will even use the old 3.5 A drive. Just in case.
Red light internaly
Digidoc 5 for thermal monitoring on:
1.cpu 2.ram 3.VGU 4.case 5.HDD 6.other ram 7.chipset 8.dvd for curiousity sake. just curious of the temps they produce. but always able to move it to a more vital area if the need arises.
Will be upgrading to liquid cooling in the future, that way when I am deployed the temps stay in the blue. (HOPEFULLY)

Zynq custom board not booting from SD-Card

Hi all,
I have a custom designed board woth a Zynq XC7Z100 SoC and try to bring it up. The schematics are based on the ZC706 board so the MIO connections on the PS are the same.
Now I'm trying to boot just the simple Hello World example from XSDK (Vivado Version 2014.3). Booting from JTAG and from QSPI Flash is working but booting from SD-Card fails. The FSBL is producing the following output:
Xilinx First Stage Boot Loader
Release 2014.3 Nov 5 2014-17:42:52
Devcfg driver initialized
Silicon Version 3.1
Boot mode is SD
SD: rc= 0
SD: Unable to open file BOOT.BIN: 3
SD_INIT_FAIL
FSBL Status = 0xA009
This Boot Mode Doesn't Support Fallback
In FsblHookFallback function
I've measured all data pins and they are toggling. What I've found out is that the SDIO Clk is somehow strange. When starting the FSBL it is a very slow clock (kHz) and afterwards it's speeding up to 41.6666 MHz. I've already changed the SDIO clock in Vivado from 125 MHz to 50 MHz but nothing changes, when I'm measuring it. Do I miss something out?
Any help would be greatly appreciated.
Thanks
Christoph

I believe the clock is behaving properly. The driver should connect at a slow clock at first then increase to the highest clock that the driver thinks the card can support. If you see this clock speed change, the initialization must be getting past the first few SD card messages. You could try to adding printfs in the card driver to see which message failed.
I've had problems switching from 14.7 to 2014.3 FSBL. The later driver dropped support for older SD card and stop on very first message to the card. Maybe try a different card.
In going from dev board to custom board, did you switch from full size SD to micro SD? The micro SD format does not have a WP signal. Maybe no CD signal either. The FSBL driver cares about both.
Some official answers:
http://www.xilinx.com/support/answers/59476.html
http://www.xilinx.com/support/answers/52023.html

How to boot from SD-card on Satellite Pro S300?

My windows 7 32bit based S300 has a build-in SD card reader. The Toshiba utility for making the SD card bootable comes with an error message stating Fault: 00-61-FF02-26.
Is does not see or recognize the card.
In the BIOS version 3.00 WIN there is also no possilility for booting from SD card.
The SD card can be formatted and you can read and write to the card.
Why is this not possible?

As far as I know the BIOS of the Satellite Pro S300 supports the following bootable devices:
- USB FDD,
- Primary HDD,
- ODD (or USB ODD),
- Network(LAN),
- SD-CARD,
- USB Memory, supported at the same time
So BIOS provides the booting from SD card.
You should try following way:
Insert the SD card in the SD card slot and then power up the notebook.
Then press F12 in order to get the boot menu. Now the SD card should appear in the menu

Downloading apps it asks for apple ID Pass then it says "verification required". Then says Security Code required. Doesn't accept code. itunes doesn't accept code from visa card either?Please Help

Downloading apps it asks for apple ID Pass then it says "verification required". Then says Security Code required. Doesn't accept code. itunes doesn't accept code from visa card either?Please Help

If it is trying to verify your payment info, I would be willing to guess that it is looking for the security code for your credit card. Did you credit card just get replaced lately or the expiration date change? When is the last time that you updated your payment information in iTunes?

P10-873 boot from SD card?

Hi there
Is this possible? The BIOS has an option to enable/disable the SD slot so presumably the slot can be accessed to some extent at BIOS level. I've tried setting the Removable Drives to the top of the boot order and putting in an SD card with Windows 98 boot files on it, but it ignores this and boots from the hard drive. Is there a way?
Thanks
Mark

Hi Mark,
I had the same problems when I tried to boot from a SD card. I tried different settings but it didn't boot!
Then I called a toshiba technican and they told me that booting from SD card is at the moment not possible. Toshba is working on a solution, but we have to give them a little bit more time!
Cu Theo

V3-471G how to boot from SD CARD?

On the BIOS BOOT MENU I dont see any sd card option. Is it possible to enable booting from sd card?

as far as i know, it's not possible.

T400 Boot from SD card

Hi,
I just got a 8 GB SD card and I was wondering if anyone know how to or if its possible at all to install Ubuntu 8.10 in persistence mode to an SD card and have it run off that on a Lenovo T400.
Thanks.

In the user's manual, it is clearlu written that it can be boot from SD card. Anyway, I made it done with USB flash memory. Now, I am using my laptop with new Win XP. Although there was small glitch, it worked.
The program 'WinToFlash' seemed that it did not work, and I found accidently (pure coincident) software 'WinsetupFromUSB' version 0-2-3 in the internet, and followed the instruction. It worked. So, problem is solved anyway. Thank you for your help.

R100 Boot from PC-CARD?

Hi,
I own a SanDisk SDP3B 1.2GB (Industrial Grade) ATA PC-CARD which I'm trying to make bootable in order to run another O/S on. I'm also considering putting a recovery image on it with the help of Acronis TrueImage, so I just can boot from the card to restore my computer.
This isn't working well and I have not been successful in getting this to work. I'm wondering if anyone else have tried to boot off a pc-card with their R100's?
Thanks,
Tim

Hi
In my opinion there is no enough capacity for whole image on this card. I have no experience but try to check all BIOS settings. Check if there is a option called Boot from other devices.

AP 2 doesn't support restoring from 1.5 Vaults

I had an AP 1.5 Library containing JPG images only (no raw files), and one project, containing folders and a book. I had this library backed up to vault. I installed AP 2. I restored this vault into AP 2. AP lost 100% of my data: images, project, folders, and book. I was left with a completely empty library. This is 100% data loss. It appears AP 2 just isn't backward compatible. It doesn't support 1.5 JPGs, it cannot properly upgrade 1.5 libraries, and it cannot restore 1.5 vaults.
See related post:
http://discussions.apple.com/message.jspa?messageID=6699965#6699965
I'm headed to the Apple Store right now to return AP 2. I burned months with AP problems on the 1.0 release...not this time around. Consumers should not be alpha testers.
B

Thanks for the reply.
Complete Newbie wrote:
Bradley,
After reading this and your other thread, might I suggest you have a different problem - you have a broken 1.5 library. If it doesn't upgrade, restore-from-vault, or otherwise work, I'd blame the library first.
...except that it works just fine in 1.5. And if it were corrupt, it seems that it would raise the question of how one could successfully create a vault without any errors if the library were corrupt in the first place. And finally, if this is the problem, then take your pick ... AP 1.5 corrupts libraries without any outward signs or indication that it has done this?
Complete Newbie wrote:
I assure you that I have restored a 1.5 vault with 2.0; and I'm not alone - there are countless reports of people doing just that after purchasing 2.0 if you look in the forums around the launch-date. I don't have any problems with JPEG images either (whether from 1.5 or 2.0). It was certainly backwards-compatible for me.
Glad to hear it has worked for some. Unfortunately, I'm not working with your images, on your hardware configuration, with software purchased with your money. So the fact that others are working fine doesn't lend any comfort to the fact that I've experienced 100% data loss, and the product is unusable.
Complete Newbie wrote:
Did you try reporting the problem to Apple ? Perhaps even offering to send them the problem vault ? It sounds like a small vault (only 100 JPEG images). Even if it's corrupted, they may be able to recover your photos.
Yes, I reported both problems to Apple as a bug report. Unfortunately, I learned the hard way the first time around with AP 1.0 -- it may be months or never before this problem is addressed. I've run through this whole cycle now twice, with exactly the same results both times. I'm going to try one more thing: uninstalling AP 2 and reinstalling AP 1.5, and trying this library again in 1.5. If that doesn't work, I don't really care if Apple can recover the photos or not -- I cannot use a data management app that loses data, and further, I won't burn my time/revenue again spending hours testing an app I paid for to work. I'll be returning AP 2.
B

Ideapad S205 doesn't support booting from SDHC-Card

Similar Messages

Maybe you are looking for