Ideapad u310 is not powering up - all lights are blinking

Hi, i got a u310 that is not starting. Not only not booting, but not powering up at all. Plugged or unplugged the result is the same. All lights are blinking when i press the power or novo button(power button, power led, battery led and caps lock light, all white). They all blink together each 5 seconds and i hear a small click, like it's trying to power on or something. I can however press the power button again for a couple of seconds to turn it off.
The battery led blinks only when it is unplugged. When it is plugged, the battery light stay on(solid, white).
Anyone can help ? I've looked through the forum and could'nt find anything about this.
Thanks in advance

1. Remove any peripherals connected to the laptop.
2. Remove any power strips and surge protectors.
3. Remove the battery.
4. Press and hold the power button for 5 seconds.
5. Install the battery back and try to power ON.
6. Connect the charger and try to power ON.

Similar Messages

HP Officejet 7000 Wide Format Printer Series Error "ALL LIGHTS ARE BLINKING?"

What are the causes of my printer HP Officejet 7000 Wide Format had this error "all lights blinking"? Which part of my printer have a problem? please help!! thankzzzz......

Hello ryigo24,
Welcome to the HP Forums.
I see that you are having an issue with all the lights blinking on the printer.
Please click on the following link that deals with Blinking Lights.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Problem with WRT54G. All lights are Blinking

I do not know very much about technology and my router stopped working correctly. Now, the lights of Power, Internet, and the ones of the numbers 1 and 3 are blinking and the wireless connection does not work. Can anyone explain me what to do to solve this? I will be very grateful. Javier

hi... power cycle the n/w by unplugging power cable of modem and router, by unplugging power cable of modem and router...wait for couple of minutes, power up the modem first and once modem is rebooted power up the router, check whether lights stopped blinking or not, if lights are still blinking in that case you may need to reset the router back to factory default settings by pressing reset button on the back panel of the router but before you can reset the router let me know which internet connection are you using...so that i can tell you step by step configuration of the router...

WRH54G ALL LIGHTS ARE BLINKING WHAT SHOULD I DO?

Hi,
All the lights of my router are all blinking and the light of the ethernet on my modem is dead everytime i plug in my router but if i directly connect my dsl modem to my computer its working. any help on this thanks.

Reset the router to defaults. If that doesn't work, try this procedure.

I do have a Deskjet 5740 with all lights fast blinking. Unplug and plugin again does not help.

I do have a Deskjet 5740 with all lights fast blinking. Unplug and plugin again does not help. That's already it. I would like to know if anybody can tell me if the means the machine is completely broken. Or if this is a seldom failure situation that can be solved somehow. Please don't overlook that it's f a s t blinking.

I wanted this question one more day on the first site.

My apple tv is not working, the front light its blinking

my apple tv is not working the front light its blinking the only image on my tv is the apple picture

You need to restore
Restore your Apple TV (2nd and 3rd generation) - Apple Support

Is there a fix to touch not working? All updates are done. Intermittent problem

Is there a fix to touch not working? All updates are done. Intermittent problem

Do a reboot by holding both the power and home buttons until the apple logo appears, ignore the red slider if that appears.
If that does not help, take it to an Apple store genius bar and have the techs check it out to make sure there is not a hardware issue.

TS4079 Siri is not responding. All settings are the same as my wifes I4s. Her Siri works and my I5 does not.

Siri is not responding. All settings are the same as my wifes I4s. Her Siri works and my I5 does not. Any suggestions?

I just cycled my phone completely off (30 sec) then back on again. It seamed to help, it's working now!!!

Deskjet 6127 -- All the lights are blinking; can't turn it off. Cartridges are stuck.

Has anyone had this problem? I have a Deskjet 6127, all the lights are blinking. I can't turn it off. If I unplug it and plug it back in, (which is what it says to do on the troubleshooting site) the lights continue to blink. The ink cartridges won't slide out. Any suggestions on saving this printer from impending doom?

Hi there,
This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

My Cannon MP830 stopped scanning and faxing. Printing is fine, all lights are on.What do I do?

My Cannon MP830 stopped scanning faxing. Printing is fine, all lights are on. What do I do?

Hi Cburns!
Welcome to the Canon Forums and thanks for posting!
So that the Community can help you better, we will need to know about any error messages you're seeing (either on your computer or your printer), and the Computer Operating System you're using (Windows XP/Vista/7/8 or Mac 10.x), as well as the way you connect to your printer (USB or networked via WiFi or Ethernet).
Any other details you'd like to give will only help the Community better understand your issue!
If this is an urgent support need, please CLICK HERE to reach our friendly Technical Support Team by phone or email.
Thanks and have a great day!

SPA2100 lights are blinking in row - How to recover it ?

Hi,
My SPA-2100 lights are blinking in a row. Actually i was trying to upgrade it but i suddenly lost access during upgrade.
Since then the lights are blinking a row and I can not access it via IVR or LAn or WAN
I have downloaded recovery tool from support forums but its failing to find the device on network.
any clue?
thanks
naveed

My suggestion is check for warranty and ask for an RMA.
Regards.

Xserve will not boot up, all lights flash rapidly

Just bought a lightly used Intel Xserve. This unit was in a business that failed, and was set up, but never used. Was powered off and unplugged for approximately 18 months. When we tried to plug it up to check it out & configure it, we noticed the following:
System will not post and won't boot
Hard drives do not appear to spin
CD Drive appears to have no power - will not grab disk
All fans do work, and run on high RPM
All lights on back of server and front of server, as well as next to SDRAM slots, and on back of main board flash / flicker (regular quick flashes, no pattern evident). The only light that does NOT come on at all is the light next to the power button.
Anyone heard of a similar condition? Is this server toast?
Thanks,
Rob Hogan

I'm sorry to say I don't have a solution, but I can commiserate.
I have a G5 and two G4's, and so far within a few days / couple of weeks of getting them home and getting them up and running, they seem to fail.
Usually spectacularily.
The G5 operates very much as yours in that power on, fans rev high, and no post or other activity; I don't get any system light status action however other than flashing. I've replaced CPU's and logic board on this.
The single CPU G4's does much the same, but this I've had up and running and then it went down when I upgraded the memory to max (very careful to make sure it was within Apple spec's), and despite swappinbg the original memory back in,nothing.
My latest, a dual core G4, was bought in working order, and I upgraded this from 10.4 to 10.5. Running nicely as a internet gateway. Went away for weekend so put it into sleep mode. Came back, power button on front panel stopped working, and one of the raid slices on the system drive failed.
Tried to repair this and system now no longer boots, but freezes on loading OS (spinning disc stops in mid spin) and it will not boot from installation disc via firewire or internal DVD drive (swapped in a replacement to ensure it works). The installation disc stops at the apple splash screen, but goes no further.
I can, helpfully, get into Open Firmware mode, so something is working on some level. Sadly, I can't seem to find a copy of the Apple Hardware Test for this machine (see my post on this) to check it out.
I can tell you that I'm getting very adept at working with Xserve hardware, if not very effectively.
My working hypothesis on this is that there is some issue with these units being used 27/7x365 for however long, and then being left 'off' for a prolonged period.
Thinking that whilst they are designed to operate reliably as constantly on and working under load, so facet of being 'off' breaks 'something'.
If really pushed to go out on a limb, I'd theorise that under load the electronics/IC's settle into position, but then when switched off things cool down, contract, and causes weaknesses in electrical connections to occur. When next used, these then start to fail, giving a pattern of initial operability followed by delayed failure with a cascade of increasingly servere symptoms until terminal failure is reached.
But that is wild, uneducated, conjecture.
So, no help, but I comiserate.
XD Andy
btw, is anyone has some useful advice for me on where to find the AHT 2.0.1 for Xserve or even just the part number ... ... ...

I have a hp f380 all in one printer all 3 lights are blinking

I followed all the instructions on hp.com nothing has worked. I just bought new cartridges for the printer it has aligned 3 times already but won't copy or scan because the ink cartridge light, paper jam and power lights are all blinking at the same time what can i do? I have windows vista all the software for the printer is already installed and I use it for my compaq presario laptop. The usb cord was disconnected for 60 seconds. I also powered it off removed and re-inserted the ink cartridges and even the paper the lights still blink. And checked for paperjams
Message Edited by Nesh on 02-11-2009 11:02 PM

Try working through this support document. it walks through resetting the power module and testing it. It also includes a video which is very helpful.
The HP Product Won't Turn On or Respond
If this does not resolve your issue post back so we can get it fixed for you.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

What causes an hp c5550 all in one to turn on properly then all lights start blinking?

I Have an HP c5550 all in one printer which I think goes into oscillation and all lights on it begins blinking and the power button will not turn it off. I have to unplug it to stop it. When I reconnect it, it will work for a few minutes and starts blinking all over again. I have had it on an XP machine but just recently put it on a windows 7 ultimate machine with the exact same results. Also the last time I got it to print instead of turning off and starting blinking it just kept repeatedly printing the same page which was supposed to pring one copy. Besides jacking it up and running a new one under it, what could be the matter with it?

Hi there,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

MBox - All lights are on, no one is home

Hi, I'm Ryan. I have been using the original MBox with Logic Pro 8 for some time now, no problems whatsoever. Today I go out and by some expensive new monitors for my home studio I'm building, and of course of all days the Mbox is not working. I have tried reinstalling the Core Audio Manager, Reset the Permissions of the disk, tried two different USB cables, and tried 3 different computers. All of the lights are lit up on the Mbox, but I am getting nothing on the computers end.
Please help! I have a vocalist coming over to record in a few hours, and am excited to hear these new speakers! Thanks
What I have:
Macbook Pro running 10.5.6
Logic Pro 8
MBox (Original)
Thanks

Hi,
Check to see if the cable is a cross over ethernet or badly wired.
To check if its cross over:
Hold the cable ends side by side with the tabs away and copper contacts top
If the green and orange pairs are reversed then its a cross over cable
In the USA the standard is 568B in Canada 568A (its just a coloring standard the wiring is the same in ether case)
If your cable doesn't match either 568B or 568A its a bad cable and only working accidentally.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Ideapad u310 is not powering up - all lights are blinking

Similar Messages

Maybe you are looking for