Ideatab a3000 dead after error during firmware upgrade using flash tool

i was upgrading to firmware version 4.2.2 with call option then i got an error message and the tablet is dead
any so;utions

Dear uliwooly,
I have tried in different PC, different version of flastool and different .tft file but all are failed!
One thing i should share:
My phone can connect to flash-mode without pressing volume down key!
Plz reply....

Similar Messages

Error during Asset Scrapping using ABAVN - plz advise

Dear all,
Facing an error during asset scrapping using ABAVN for a Korean company code.
Net value of asset is not zero. Transaction type = Disposal/abandonment of prev. year acquisition.
Error occurs on Simulation - Transaction in area 40 contradicts the net book value rule
NBV in area 01 Book Dep - 108,612,225 KRW
NBV in area 40 u2013 Tax Dep u2013 108,612,192 KRW
Negative vals allowed NOT checked in asset master.
SAP says:
The document cannot be posted, as it is contrary to the net book value rule which is checked in area 40.
This error usually occurs when you enter proportional values. The proportional values exceed the amount posted, for example, post capitalization of 100 but proportional depreciation to the amount 110. Check your entries and correct them if necessary.
How do we correct this issue and scrap the asset? Is this specific to Korea? How can we make NBV in area 01 = area 40?
Any clues? Greatful for all answers
Cheers
RK

Kindly read the forum rules and then post.
SMS Language is strictly not allowed.

Errored during request submission using request see APIs

Hi guys, this error is giving me when i call a concurrent program and do a request sumission and the request status is red(error) with the next error:
"Errored during request submission using request see APIs "
Im using forms 6i and EBS

Hi,
I am getting the exact same error.
It appears when we run request sets!
We have made a trigger that sends an email to our sysadmins every time a concurrent request fails. This trigger fires on insert or update of applsys.fnd_concurrent_requests when new.status_code = 'E' /*Error*/ and new.phase_code ; = 'C' /*Complete*/.
In other words we should only get a message when the request has the status Error and is Complete.
However for request sets we get an email saying that it has failed with the following message "Errored during request submission using request see APIs". BUT, when we query the request in the Application, it has the status Normal! This applies to several different request sets.
So, my question is: Does anyone know if, or why, the standard request submission of request sets updates the status to Error for a short time, and then updates it to Normal afterwards?
Thanks
Roy

Mac mini won't boot after accidental loss of power during firmware upgrade

i accidentally hit the power switch on the wall during an upgrade (might even have been a firmware upgrade, I didn't really look at what was going on). Anyway, now it hangs on the silver Apple logo screen with a spinny wheel on reboot. It's only 3 months old, it's the $599 model.
What to do? I see that you can download firmware restoration disks but they appear to be limited to earlier versions of the Mac mini.

I took it to the Mac store today and they fixed it for free by booting from an external drive and finishing the half-baked system update. Now that I know how to do that, I can fix it myself next time.
Thanks to Alan at the Salem, NH store!!

Error during the upgrade phase "start_shdi_first"

Hello,
We are having issue with upgrading r/3 4.7 enterprise extension set to ECC 6.0
Here the error message goes....
starting system failed rc=0
to analyse the error during start of shadow instance
view files 'Startsfi.log' and 'devtrace.log'
in directory usr\..put
repeat phase until shadow instance is started
and u can logon instance no '01'"
We have changed the DDIC password during upgrade.after that we ran the initphase to update the password.
I think sapup is referring the old password which was entered initially during the upgrade and we dont remember the old password also.
Appreciate your response
Startsfi.log
1 ETQ201XEntering upgrade-phase "START_SHDI_FIRST" ("20080218175653")
2 ETQ366 Connect variables are set for shadow instance access
4 ETQ399 System-nr = '01', GwService = 'sapgw01'
4 ETQ399 Environment variables:
4 ETQ399   dbs_mss_schema=de4
4 ETQ399   auth_shadow_upgrade=1
4 ETQ399 Set environment for shadow connect:
4 ETQ399 ENV: dbs_mss_schema=de4
4 ETQ399 ENV: auth_shadow_upgrade=1
4 ETQ399 Set RFC variables for shadow connect:
4 ETQ399 System-nr = '01', GwService = 'sapgw01'
4 ETQ399 Set tool parameters for shadow connect:
4 ETQ380 computing toolpath for request "TP_SHADOW_CONNECT"
4 ETQ381 request "TP_SHADOW_CONNECT" means "tp needs to connect to shadow system"
4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
4 ETQ383 translates to path "exe"
4 ETQ383 translates to path "exe"
4 ETQ399   default TPPARAM: SHADOW.TPP
4 ETQ380 computing toolpath for request "TP_ALWAYS_NEW"
4 ETQ381 request "TP_ALWAYS_NEW" means "always tp from DIR_PUT/exe, for phase KX_SWITCH"
4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
4 ETQ383 translates to path "exe"
4 ETQ383 translates to path "exe"
2 ETQ399 Starting shadow instance
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2 ETQ353 Starting system
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2 ETQ370 starting test RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
4 ETQ232 RFC Login succeeded
2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
4 ETQ239 Logging off from SAP system
2WETQ372 test RFC failed, rc="-3"
2EETQ399 Starting shadow instance failed
2EETQ399 Test RFC failed finally
2EETQ399 Dialogue: ERROR
2EETQ399 Starting system failed, rc=0
DEVTRACE:
trc file: "dev_disp", trc level: 1, release: "700"
sysno      01
sid        DE4
systemid   560 (PC with Windows NT)
relno      7000
patchlevel 0
patchno    111
intno      20050900
make:      multithreaded, ASCII, optimized
pid        2272
Mon Feb 18 16:08:40 2008
kernel runs with dp version 229(ext=109) (@(#) DPLIB-INT-VERSION-229)
length of sys_adm_ext is 364 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (01 2272) [dpxxdisp.c   1239]
     shared lib "dw_xml.dll" version 111 successfully loaded
     shared lib "dw_xtc.dll" version 111 successfully loaded
     shared lib "dw_stl.dll" version 111 successfully loaded
     shared lib "dw_gui.dll" version 111 successfully loaded
     shared lib "dw_mdm.dll" version 111 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
Mon Feb 18 16:08:52 2008
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0065.qqq.nxst) took 12 seconds
Mon Feb 18 16:09:10 2008
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 18 seconds
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5361]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >MTW02SDEC01_DE4_01                      <
DpShMCreate: sizeof(wp_adm)          19976     (908)
DpShMCreate: sizeof(tm_adm)          3605136     (17936)
DpShMCreate: sizeof(wp_ca_adm)          18000     (60)
DpShMCreate: sizeof(appc_ca_adm)     6000     (60)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528040/528048
DpShMCreate: sizeof(comm_adm)          528048     (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm)          0     (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm)          0     (72)
DpShMCreate: sizeof(vmc_adm)          0     (1296)
DpShMCreate: sizeof(wall_adm)          (22440/34344/56/100)
DpShMCreate: sizeof(gw_adm)     48
DpShMCreate: SHM_DP_ADM_KEY          (addr: 065C0040, size: 4241064)
DpShMCreate: allocated sys_adm at 065C0040
DpShMCreate: allocated wp_adm at 065C1B30
DpShMCreate: allocated tm_adm_list at 065C6938
DpShMCreate: allocated tm_adm at 065C6968
DpShMCreate: allocated wp_ca_adm at 06936BF8
DpShMCreate: allocated appc_ca_adm at 0693B248
DpShMCreate: allocated comm_adm at 0693C9B8
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 069BD868
DpShMCreate: allocated gw_adm at 069BD8A8
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 069BD8D8
DpShMCreate: allocated wall_adm at 069BD8E0
MBUF state OFF
DpCommInitTable: init table for 500 entries
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation view
<EsNT> Using memory model view.
<EsNT> Memory Reset disabled as NT default
<ES> 2046 blocks reserved for free list.
ES initialized.
WARNING => System running without ICM - check rdisp/start_icman [dpxxdisp.c   12437]
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG Q0K=> DpMsAttach, mscon ( MTW02SDEC01) [dpxxdisp.c   11753]
DpStartStopMsg: send start message (myname is >MTW02SDEC01_DE4_01                      <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c   1050]
DpMsgAdmin: Set patchno for this platform to 111
Release check o.K.
Mon Feb 18 16:09:13 2008
MBUF state ACTIVE
DpModState: change server state from STARTING to ACTIVE
trc file: "dev_ms", trc level: 1, release: "700"
[Thr 4724] Mon Feb 18 16:08:40 2008
[Thr 4724] MsSSetTrcLog: trc logging active, max size = 20971520 bytes
systemid   560 (PC with Windows NT)
relno      7000
patchlevel 0
patchno    110
intno      20050900
make:      multithreaded, ASCII, optimized
pid        5420
[Thr 4724] ***LOG Q01=> MsSInit, MSStart (Msg Server 1 5420) [msxxserv.c   1824]
[Thr 4724] MsInitAclInfo: acl file D:\usr\sap\put\DE4\SYS\global\ms_acl_info.DAT not found, unrestricted access
[Thr 4724] MsGetOwnIpAddr: my host addresses are :
[Thr 4724]   1 : [172.20.28.159] MTW02SDEC01.mindsap.com (HOSTNAME)
[Thr 4724]   2 : [127.0.0.1] MTW02SDEC01.mindsap.com (LOCALHOST)
[Thr 4724] MsHttpInit: full qualified hostname = MTW02SDEC01.mindsap.com
[Thr 4724] HTTP logging is switch off
[Thr 4724] MsHttpOwnDomain: own domain[1] = mindsap.com
[Thr 4724] ms/icf_info_server : deleted
[Thr 4724] *** I listen to port sapmsSHDDE4 (3601) ***
[Thr 4724] CUSTOMER KEY: >J1537289841<
trc file: "dev_rd", trc level: 1, release: "700"
Mon Feb 18 16:09:10 2008
***LOG S00=> GwInitReader, gateway started ( 2344) [gwxxrd.c     1694]
systemid   560 (PC with Windows NT)
relno      7000
patchlevel 0
patchno    110
intno      20050900
make:      multithreaded, ASCII, optimized
pid        2344
gateway runs with dp version 229(ext=109) (@(#) DPLIB-INT-VERSION-229)
gw/local_addr : 0.0.0.0
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 40000000 for monitoring segment.
Bind service sapgw01 (socket) to port 3301
GwPrintMyHostAddr: my host addresses are :
1 : [172.20.28.159] MTW02SDEC01.mindsap.com (HOSTNAME)
2 : [127.0.0.1] MTW02SDEC01.mindsap.com (LOCALHOST)
DpSysAdmExtCreate: ABAP is active
DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
DpShMCreate: sizeof(wp_adm)          19976     (908)
DpShMCreate: sizeof(tm_adm)          3605136     (17936)
DpShMCreate: sizeof(wp_ca_adm)          18000     (60)
DpShMCreate: sizeof(appc_ca_adm)     6000     (60)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528040/528048
DpShMCreate: sizeof(comm_adm)          528048     (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm)          0     (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm)          0     (72)
DpShMCreate: sizeof(vmc_adm)          0     (1296)
DpShMCreate: sizeof(wall_adm)          (22440/34344/56/100)
DpShMCreate: sizeof(gw_adm)     48
DpShMCreate: SHM_DP_ADM_KEY          (addr: 06110040, size: 4241064)
DpShMCreate: allocated sys_adm at 06110040
DpShMCreate: allocated wp_adm at 06111B30
DpShMCreate: allocated tm_adm_list at 06116938
DpShMCreate: allocated tm_adm at 06116968
DpShMCreate: allocated appc_ca_adm at 0648B248
DpShMCreate: allocated comm_adm at 0648C9B8
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 0650D868
DpShMCreate: allocated gw_adm at 0650D8A8
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 0650D8D8
MtxInit: -2 0 0
Mon Feb 18 16:09:14 2008
GwDpInit: attached to gw_adm at 0650D8A8
Thanks,
Vadi

Dear All,
The issue has been resolved by changing the DDIC password to what it was when we have started the upgrade.The password was "welcome" when we have started with upgrade after that it has been changed to
"basis05" during upgrade.we changed it back to welcome and it started working fine.
Here it took long time to find out what was the password when we have starte upgrade.Resetting to standard ddic password also ddint help out in our case.
Thanks for all your replies.

Connection reset during firmware upgrade

I have a Linksys WRT54GS (v5) router. I noticed that my firmware was outdated and tried to upgrade it tonight. During the upgrade progress, the browser reset the connection and now cannot access my router configuration pages.
I did a hard reset. Then I did the 30-30-30 reset.
The reset worked but no matter what I do, I cannot navigate to any readable page within the router. I get the log in box and successfully log into the router. However, the configuration page(s) are all jumbled and devoid of useful information. It almost looks like a web page that needs flash to be enabled. Lots of colors and boxes but no text or links to other configuration pages
I know it's an old router but it has served me well. I would love to reinstall the old firmware (or new!) and copy my saved configuration file back to the router.
Is this a hopeless situation?
Is there a way to access the configuration via a command line interface?
Please, any help would be greatly appreciated.
Solved!
Go to Solution.

Actually, thanks for your answer but I posted too soon. I just found a solution to my problem.
Rather than try to rewrite the original persons instructions, I will copy and paste them below.
I found this fix on the following site:
http://en.kioskea.net/forum/affich-87540-can-t-view-linksys-router-web-page-wrt54g
Scroll down to the Comments section and find the one by "elmo21". The find the reply by "Lynn". I hope this helps someone.
It worked like a charm for me:
Lynn - Dec 12, 2009 2:59pm GMT
Hey guys,
I was faced with similar problem, that the page 192.168.1.1 can't seems to load properly. After surfing the net in search for solution, i finally got the answer! Now i can access the page without problem.
The problem is likely due to router firmware issue. This is what you can do.
1) Go to http://www.linksysbycisco.com/APAC/en/support to search for your router model, and download the latest firmware
2) Go to http://www.idealinternet.co.uk/restore-linksys-firmware.tpl and download the linksys-tftp.exe available on that page
3) Run the linksys-tftp.exe program. Key in the details as below:
Server : 192.168.1.1
Password : admin
File : <look for the firmware file that you had download earlier>
4) Click Upgrade
5) You should be able to see the progress bar that shows upgrading in process and eventually, it will show a message that firmware had been upgraded
6) After that, try going to the page 192.168.1.1 . Leave the username blank and key password as admin
7) The page should load nicely after the firmware had been upgraded successfully!!
Hope the above works for you guys!!

Lenovo A536 stuck during firmware upgrade

My Lenovo A 536 is not starting, it gives the error No Command at start.
I was upgrading its firmware but is stopped automatically and rebooted.
On start it is not booting completely.
please help me anyone. Or please give me stock ROW Rom so that I can flash it to original state or someone please give me update.zip so that I can install from recovery... please

1. You need to have adb drivers installed (google for that).2. You need mt65xx usb vcom drivers.Click Here To DownloadIf you feel any problem to install vcom driver, watch this video on YouTube click here3. Flash Stock Rom using Smart Phone Flash Tool
Step 1: all drivers installed
Step 2: Power Off your Android Smartphone and remove the Battery (if it is removable).Don not connect your phone to PC now.Step 3: Download the Stock Rom form here extract it on your Computer.Step 4: Extract Smart Phone Flash Tool on Your Computer.Step 5: Run Flash_tool.exe located in folder SP_Flash_Tool_v5.1352.01Step 6: Once Smart Phone Flash Tool is launched, Click on the ScatterLoading Button from the Right. Select Scatter file located in Target_bin folder MT6582_Android_scatter.txtStep 7: Now, Click on the Download Button to begin the Flashing Process.Step 8: After that only connect your Smartphone to the Computer using USB Cable (without battery if it is removable). After connecting the device to the computer it will start downloading , will take 10 mins to download fully.

N96 crash during firmware upgrade & unrecoverable

Finally Nokia sent me a text to say that a firmware upgrade - from 10 to 11 was available. I've tried to install it after first backing up the phone. During upgrade where the upgrade software continually referred to connection problems (while the Nokia PC Suit showed the connection to be in place) with about 5 minutes of remaining installation time the installer gave up. It asked me to turn off the phone and reconnect which I did. The installer could not recover the installation. I now have a phone that will turn on but just has a blank screen and PC Suit won't recognise it so I can't restore from the backup.
Any ideas? Does my second N96 have to be sent back to Nokia?
This is all becoming rather silly...

B4 you update I found this improves the way it works
before you connect phone by USB
Plug in charger and leave in (make sure its turned on at the wall socket)
1st switch to line 1 if you have 2 lines
set profile on genral
turn off password on boot
turn OFF pincode request
turn OFF fixed dial
IF you have Lights ON installed uninstall it (you can put it back after)
if You have any other prog that RUNS all the time Like Lights ON unistall that too. (eg rotate me on N95)
TURN OFF PHONE
remove SD card
TURN ON PHONE to get a clean boot with nothing running in background
now make sure you connect in PC suite mode when you plug in USB
run P C suite click on Spanner TOOLS
go down to software update
NOW WAIT if it says there is a new version or it loads new drivers
there are 5 or 6 cable drivers that it MUST load before it starts it only does that once the 1st time
Now all will go well
most of the crashes are caused by either a prog running on the phone or the pin or password being set and the phone cant reboot or a flat battery
Message Edited by ivor_bigun on 11-Nov-2008 05:27 PM
Nokia user / modder since Nokia Orange and Mobira user too before that

SCM5 - SCM7 Upgrade Error during LiveCache upgrade Step C4

We are in the process of upgrading our SCM5 system to SCM7 release level. During livecache upgrade step C4 to load transaction data, we are getting error CONNE_IMPORT_WRONG_COMP_TYPE. The dump says that "when importing the object 'OT_ORDERS", the component no. 5 in the dataset has a different type from the corresponding component of the target object in the program "/SAPAPO/SAPLOM_UPGR_PARALLEL". The data type is "P" in the dataset, but "C in the program".
Our source livecache version is 7.6.03.12 and target livecache version we are upgrading to is 7.7.04.29. We used BS 7 SR1 liveCache 7.7.04 DVD from service marketplace. We did not use the update DVD since the guide mentioned that customers on SCM5.1 or higher need to run livecache upgrade from update DVD.
All steps in A, B have already been completed.
More details from the ST22 dump -
Error analysis | | An exception occurred that is explained in detail below. | | The exception, which is assigned to class 'CX_SY_IMPORT_MISMATCH_ERROR', was | | not caught in | | procedure "GET_DB" "(METHOD)", nor was it propagated by a RAISING clause. | | Since the caller of the procedure could not have anticipated that the | | exception would occur, the current program is terminated. | | The reason for the exception is: | | When importing the object "OT_ORDERS", the component no. 5 in the | | dataset has a different type from the corresponding component | | of the target object in the program "/SAPAPO/SAPLOM_UPGR_PARALLEL". | | | | The data type is "P" in the dataset, but "C" in the program. Information on where terminated | | Termination occurred in the ABAP program "/SAPAPO/SAPLOM_UPGR_PARALLEL" - in | | "GET_DB". | | The main program was "SAPMSSY1 ". | | | | In the source code you have the termination point in line 3222 | | of the (Include) program "/SAPAPO/OM_UPG_CLASS_IMPCLUT". | | The termination is caused because exception "CX_SY_IMPORT_MISMATCH_ERROR" | | occurred in | | procedure "GET_DB" "(METHOD)", but it was neither handled locally nor declared | | in the RAISING clause of its signature. | | | | The procedure is in program "/SAPAPO/SAPLOM_UPGR_PARALLEL "; its source code | | begins in line | | 3221 of the (Include program "/SAPAPO/OM_UPG_CLASS_IMPCLUT ".
We are running AIX5.3 and Oracle 10.2.0.2.0.
Any help here will be greatly appreciated.

This is exactly the same with OSS 305147 2010. It will be answered in BC-DB-LCA area.

WRV54G - error loading firmware upgrade (v2.392)

I went to upgrade the firmware on my WRV54G -
Downloaded the latest firmware -- v2.392 (5MB file - name WRV54G_R2_39_2_02082006)
In the router - I go to the Administration / Config Mgmt page - and tried to load the firmware upgrade and I get a blank browser screen with the following error message
'413 Request Entity Too Large'
'The length is too large'
Has someone also found this? Is there a simple fix?

Hi… I think there was some error while downloading this file. Try downloading it again. Reset this router for 1 min and try to upgrade the firmware again. Let me know if you can upgrade it.

Zen Micro constantly FREEZES during FIRMWARE UPGRADE - totally bricked!

Hey,
It's just like it says. My Zen Micro currently has no firmware besides the recovery OS because I chose "reload firmware."? I try to upgrade to both versions of the Zen Micro firmware (.x and 2.x) and as soon as my computer gets started and the Zen Micro has the little "data exchange" icon on there, the computer and Zen Micro hang. The progress bar gets nowhere and it's the Micro that's frozen, not the computer or the firmware upgrade program (I'm a software engineer, I know if it's the program freezing, and it is NOT).
How in blazes is this happening? How can I stop my Micro from freezing? It's all so confusing!
By the way, stats about the PC used:
OS: Windows XP Sp2
Windows Media Player 0 installed
USB 2.0 ports

I have exactly the same issue. Just tried to run the v.x to v2.x firmware upgrade and its been in recovery mode ever since. I tried to run the clean up / format / reload firmware option but it didn't work it just keeps coming back to the recovery mode. Anyone know how to fix this ? I was due to be getting on a 20 hour flight with this one as my company in half a days time so anyone with any good suggestions feel free to tell me ASAP!
ThanksSteve

Error during Java SPS Update (LM-TOOLS)

Hello,
I am currently upgrading SAP EHP 1 for SAP NetWeaver 7.0 from SPS06 to SPS14 and I get an error during LM-TOOLS component update.
Here is the error log:
14/03/17 14:24:31 - ***********************************************************
14/03/17 14:24:31 - Start updating EAR file...
14/03/17 14:24:31 - start-up mode is lazy
14/03/17 14:24:31 - EAR file updated successfully for 33ms.
14/03/17 14:24:31 - Start updating...
14/03/17 14:24:32 - EAR file uploaded to server for 42ms.
14/03/17 14:24:32 - ERROR: Not updated. Deploy Service returned ERROR:
                     java.rmi.RemoteException: Cannot deploy application sap.com/tc~sec~auth~spnego~wizard..
                     Reason: Clusterwide exception: Failed to deploy application sap.com/tc~sec~auth~spnego~wizard. Check causing exception for details (trace file). Hint: Are all referenced components deployed and available on the engine?; nested exception is:
                      com.sap.engine.services.deploy.container.DeploymentException: Clusterwide exception: Failed to deploy application sap.com/tc~sec~auth~spnego~wizard. Check causing exception for details (trace file). Hint: Are all referenced components deployed and available on the engine?
                      at com.sap.engine.services.deploy.server.DeployServiceImpl.update(DeployServiceImpl.java:689)
                      at com.sap.engine.services.deploy.server.DeployServiceImplp4_Skel.dispatch(DeployServiceImplp4_Skel.java:1278)
                      at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:336)
                      at com.sap.engine.services.rmi_p4.DispatchImpl._run(DispatchImpl.java:201)
                      at com.sap.engine.services.rmi_p4.server.P4SessionProcessor.request(P4SessionProcessor.java:137)
                      at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
                      at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
                      at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
                      at java.security.AccessController.doPrivileged(Native Method)
                      at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)
                      at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)
                     Caused by: com.sap.engine.services.deploy.container.DeploymentException: Clusterwide exception: Failed to deploy application sap.com/tc~sec~auth~spnego~wizard. Check causing exception for details (trace file). Hint: Are all referenced components deployed and available on the engine?
                      at com.sap.engine.services.webdynpro.WebDynproContainer.deploy(WebDynproContainer.java:1052)
                      at com.sap.engine.services.webdynpro.WebDynproContainer.makeUpdate(WebDynproContainer.java:1283)
                      at com.sap.engine.services.deploy.server.application.UpdateTransaction.makeComponents(UpdateTransaction.java:402)
                      at com.sap.engine.services.deploy.server.application.DeployUtilTransaction.commonBegin(DeployUtilTransaction.java:325)
                      at com.sap.engine.services.deploy.server.application.UpdateTransaction.begin(UpdateTransaction.java:166)
                      at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhasesOnOneServer(ApplicationTransaction.java:292)
                      at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhases(ApplicationTransaction.java:326)
                      at com.sap.engine.services.deploy.server.DeployServiceImpl.makeGlobalTransaction(DeployServiceImpl.java:3241)
                      at com.sap.engine.services.deploy.server.DeployServiceImpl.update(DeployServiceImpl.java:677)
                      ... 10 more
                     For detailed information see the log file of the Deploy Service.
14/03/17 14:24:32 - ***********************************************************
Mar 17, 2014 2:24:32 PM Info: End of log messages of the target system.
Mar 17, 2014 2:24:32 PM Info: ***** End of SAP J2EE Engine Deployment (J2EE Application) *****
Mar 17, 2014 2:24:32 PM Error: Aborted: development component 'tc/sec/auth/spnego/wizard'/'sap.com'/'MAIN_NW701P13_C'/'4487597'/'0', grouped by software component 'LM-TOOLS'/'sap.com'/'MAIN_NW701P14_C'/'1000.7.01.14.0.20130801094512''/'0':
Caught exception during application deployment from SAP J2EE Engine's deploy service:
java.rmi.RemoteException: Cannot deploy application sap.com/tc~sec~auth~spnego~wizard..
Reason: Clusterwide exception: Failed to deploy application sap.com/tc~sec~auth~spnego~wizard. Check causing exception for details (trace file). Hint: Are all referenced components deployed and available on the engine?; nested exception is:
com.sap.engine.services.deploy.container.DeploymentException: Clusterwide exception: Failed to deploy application sap.com/tc~sec~auth~spnego~wizard. Check causing exception for details (trace file). Hint: Are all referenced components deployed and available on the engine?
(message ID: com.sap.sdm.serverext.servertype.inqmy.extern.EngineApplOnlineDeployerImpl.performAction(DeploymentActionTypes).REMEXC)
Mar 17, 2014 2:24:32 PM Info: Starting to save the repository
Mar 17, 2014 2:24:32 PM Info: Finished saving the repository for 193 ms.
Mar 17, 2014 2:24:32 PM Info: Starting: Update: Selected software component 'LM-TOOLS'/'sap.com'/'MAIN_NW701P14_C'/'1000.7.01.14.0.20130801094512''/'0' updates currently deployed software component 'LM-TOOLS'/'sap.com'/'MAIN_NW701P06_C'/'1000.7.01.6.0.20100108201135''/'0'.
Mar 17, 2014 2:24:32 PM Error: Aborted: software component 'LM-TOOLS'/'sap.com'/'MAIN_NW701P14_C'/'1000.7.01.14.0.20130801094512''/'0':
Failed deployment of SDAs:
development component 'tc/sec/auth/spnego/wizard'/'sap.com'/'MAIN_NW701P13_C'/'4487597'/'0' : aborted
Please, look at error logs above for more information!
Mar 17, 2014 2:24:32 PM Info: Starting to save the repository
Mar 17, 2014 2:24:33 PM Info: Finished saving the repository for 193 ms.
Mar 17, 2014 2:24:33 PM Info: J2EE Engine is in same state (online/offline) as it has been before this deployment process.
Mar 17, 2014 2:24:33 PM Error: ---------------- At least one of the Deployments failed ---------------
Any help will be really appreciated.

Hi Johnny,
You need to undeploy the sap.com~spnego.cfg.wd component using SDM
Then retry the patching of LM-TOOL patching
Also follow the SAP Note
1643003 - Deployment of LM-TOOLS fails. Due to SPNego
With Regards
Ashutosh Chaturvedi

Befw11s4 v2 firmware upgrade using mac os x?

How might I upgrade the firmware on a linksys befw11s4 v2 wireless router using mac os x?
Thanks,
Harry

Thiis an old thread, but maybe the next person will see this:
It is not necesary to extract the .bin file on a Mac to upgrade your firmware. Just browse to the .bin file where you downloaded it to begin the firmware upgrade.
See gv's thread here: http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&message.id=19173#M1...
Message Edited by kamikyo on 01-20-2009 09:49 AM

Applications won't open after error in a update using a Apple G4

Apple G4 wont open applications, it says application switcher error or error type 3, everthing used to work until when updating the mac a error accured it restarted, now it won't open an application without saying error type 3, or when it boots a bomb sign with the following message saying application switcher error please restart. does anyone know what i can do or whats happened? i have a boot disk which isn't the offical apple cd as i cannot find it or find a place where i could get one from if anyone knows where i could get one from that would be most helpful!!
Thanks.

haydn,
It sounds like you are talking about Application Switcher from system 6, twenty five years ago. If you are using system 9 and you happened to have other systems on your hard drive, the computer could get confused with what to do becausse it sees older software that the processor can not handle.
I looked at a map of England and did not recognize any cities that would have a Mac user group. If you google and find a user group near you, the best thing to do would be to find a Boot CD, put it in, restart while holding down the C key and see if you can clean up your drive.
Otherwise, ebay has boot CDs listed from time to time. This may look tempting:
http://cgi.ebay.co.uk/iBook-G3-Install-cds-x7-10-2-Jaguar-OS-9-2-2-OS-8-/2207859 53727?pt=UK_Computing_Apple_Mac_Accessories&hash=item3367de4bbf
But, here is the catch. The disks look like they are grey and not the universal install CDs. If one of the CDs is not for your exact model of computer, be sure and look for a CD that is white with an orange 9 on it.
Jim

CE71: error during applying SP with CEUPDATE tool

Hi Experts ,
Iam getting following error while updating SP through CEUPDATE tool .
The execution of a command has failed
Error message: Unable to start JSPM. $(0) Remote connection was closed.
The request could not be processed.
SOLUTION: Check the file UpdateSystem.log for more information on how to solve the problem.
Progress of TASK_DEPLOY
Status         : ERROR
Total Units    : 100
Current Units : 5
Progress       : 5
Status Details :
   com.sap.sdt.jspm.c42.exceptions.StartException: Unable to start JSPM. $(0)
Remote connection was closed. The request could not be processed.
Exception      : com.sap.sdt.jspm.c42.exceptions.StartException: Unable to start JSPM. $(0)
Remote connection was closed. The request could not be processed.
TaskResult     : null
Exception in thread "C42JSPMAdapter_Deploy" java.lang.NullPointerException:
        at com.sap.sdt.jspm.c42.workers.DeployWorker.run(DeployWorker.java:192)
        at java.lang.Thread.run(Thread.java:725)
com.sap.lm.jspmadapter.standalone.adapter.CallJSPMAdapter-INFO: JSPM finished with an error rc: 3
com.sap.sdt.jspm.c42.exceptions.StartException: Unable to start JSPM. $(0)
Remote connection was closed. The request could not be processed.
        at com.sap.sdt.jspm.c42.workers.JspmConnectWorker.startJSPM(JspmConnectWorker.java:153)
        at com.sap.sdt.jspm.c42.workers.DeployWorker.deploy(DeployWorker.java:115)
        at com.sap.sdt.jspm.c42.workers.DeployWorker.run(DeployWorker.java:176)
        at java.lang.Thread.run(Thread.java:725)
Caused by: com.sap.sdt.jspm.rapi.connector.JSPMConnectorException: Remote connection was closed. The request could not be processed.
        at com.sap.sdt.jspm.rapi.connector.JSPMConnector.waitForToolReady(JSPMConnector.java:177)
        at com.sap.sdt.jspm.rapi.connector.JSPMConnector.startJSPM(JSPMConnector.java:128)
        at com.sap.sdt.jspm.c42.workers.JspmConnectWorker.startJSPM(JspmConnectWorker.java:149)
        ... 3 more
com.sap.sdt.jspm.rapi.connector.JSPMConnectorException: Remote connection was closed. The request could not be processed.
        at com.sap.sdt.jspm.rapi.connector.JSPMConnector.waitForToolReady(JSPMConnector.java:177)
        at com.sap.sdt.jspm.rapi.connector.JSPMConnector.startJSPM(JSPMConnector.java:128)
        at com.sap.sdt.jspm.c42.workers.JspmConnectWorker.startJSPM(JspmConnectWorker.java:149)
        at com.sap.sdt.jspm.c42.workers.DeployWorker.deploy(DeployWorker.java:115)
        at com.sap.sdt.jspm.c42.workers.DeployWorker.run(DeployWorker.java:176)
        at java.lang.Thread.run(Thread.java:725)
UPDATEXE ends with 1
java.io.FileNotFoundException: class_prefetch.lst (Permission denied)
        at java.io.FileOutputStream.open(Native Method)
        at java.io.FileOutputStream.<init>(FileOutputStream.java:179)
        at java.io.FileOutputStream.<init>(FileOutputStream.java:70)
        at com.sap.engine.offline.FileClassLoader.close(FileClassLoader.java:1553)
        at com.sap.engine.offline.FileClassLoader$1InternalHook.run(FileClassLoader.java:375)
Please advise
Thanks & regards ,
Jayakrishna

Jeremy,
I am really interested in your valuable pint of view. As you may guess I am running into the same problem.
My CE is running inside a VM.
I noticed that the "normal" update process has successfully updated the JSPM, and that's fine.
How do you "update JVM as a single component"? Using JSPM? I have tried all the 4 initial JSPM options, but it looks like it's not recongizing any SCA/SAR inside my inbox. (it sees the installed version of each component but not the target one...)
Any clue?
Thanks in advance.
Alex

Ideatab a3000 dead after error during firmware upgrade using flash tool

Similar Messages

Maybe you are looking for