IDoc not received by the Webmethods

Dear Abapers,
I have a scenario :
Here the idoc is being created perfectly with all the segments prooperly populated. Also from SAP side, we are getting the message that it has been sent.
However, the receiver ( Webemthods) is saying that it is not receiving the idocs . So, what can be the possible reason ??
Appreciate your reply...
Thanks and Best Regards,
Kunal.

error send questionnaire in srm Ros
Registration - Error after Send / No Questionnaire
ROS Questionnaire link sent by email
ROS Questionaire
Re: Status for the transferred Suppliers is not updated in ROS client!

Similar Messages

Outbound IDOC not received at the receiver system.

Hi,
Im sending an IDOC from sap to a non-sap system. During this process, from sap system it is executing successfully without any erros and the status is also '03' .
The problem is that the other system is unable to receive the IDOC sent from SAP system.
The connection is like TCP/IP and the registered server program is given as 'PROGRID' in RFC destination.
I would like to know what would be the possible cases where this IDOC is not received at the receiver system.
The configuration is perfect as per my knowledge. Just want to confirm one thing 'do i need to include any message type such as "SYNCH".
Awaiting for your solutions.
Thanks
rohith

Hi,
If the IDOC is sent successfully from the sender system then the status of the IDOC will be '03' , no matter whether the receiver has received the IDOC or not.
As per your case,
Check the Partner Profile parameters , whether the basic and extended message types are used properly.
The message type Synchron (Sync) is generally needed in Inbound IDOC side. Check whether you have added SYNCH or not.
Hope this Helps.
Regards,
Abhinab Mishra.
Experience is the name everyone gives to their mistakes.

Orders02 IDOCs not received on the EDI side

Hello SRMer's
System Information:
R/3 4.6 C
Issue related to EDI Purchase orders Pushed from R/3:
We have a situation where the Orders02 IDOCS in R/3 have status Code 3 in WE02 (data passed to port successfully) with a green light, but they are not recieved on the EDI side.
Is there any extra step that needs to be done to push these IDOCS to the EDI side.
Thanks in advance.
Points will be rewarded for answers.
Best Regards,
Bob

go to we09 and send it forcefully...and then check it.

Idoc Not received?

Hi
During data loading , I got one Error that Idoc Not received.
What will be the cause of problem and How to resolve it?
Regards & Thanks
Durai

Hi Robert Negro !
I checked , Dump has been there.
How can I resolve?
what will be other causes apart from the Dump?
Thanks A Lot .
Regards
Durai

Documents I forward are not received under the original document name. How do I solve this?

Documents I forward are not received under the original document name. How do I solve this?

If you're referring to the name of the attatchment showing when viewing the entire email, that's there's no way to change how it's done. The title and body of the actual document is unchanged after it's opened.
Does this naming of the attachment really confuse the recipient? If so, put something in the body of the email to make it clear what's attached.

TS2755 My ipad does not receive messages, the bubble in the green background. My iphone does.

My ipad does not receive messages, the bubble in the green background. My iphone does.
I can use my ipad to send messages, but it only moniltors the ones i send with the ipad. All the other messages I get on my iphone are missing.
Any idea why?

"The bubble in the green background" indicates the message was an SMS (cellular text) message. If the background were blue, it would mean the message was an iMessage.
The difference is important. Your iPad is not a cellular telephone. It cannot send or receive cellular text or MMS messages. It is, however, an Apple device which means it can communicate using Apple's iMessage to/from other Apple devices (typically over WiFi).

Aironet 1600 - A response was not received from the router or access point

Hi,
I'm trying to set up a wireless network with multiple SSID's. The new network only has CISCO products (router, switches). For the moment I'm trying to connect to 1 SSID (Windekind.Gast). the SSID is visible but when connecting devices have te folowing error message in the log:
Connection status summary
Connection started at: 2015-02-17 09:55:49-951
Profile match: Success
Pre-Association: Success
Association: Fail
Security and Authentication: Not started
Root cause:
Wireless association to "Windekind.Gast" failed
A response was not received from the router or access point.
Detailed root cause:
Wireless association to this network failed. Windows did not receive any response from the wireless router or accesspoint.
The signal is perfect (I'm only a few feet away from the AP).
To make sure there is no dhcp problem I tested the swich port in access mode for vlan 30 which supplied an IP correctly. I'm really not seeing the problem and searched the web for days now! Any help would be very much appreciated!
Below the config of the access point (done via de web interface).
! Last configuration change at 05:30:28 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2452
no preamble-short
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end

Hi Rasika
thanks for the reply! 10.0.0.81 belongs to vlan 1. I changed the config as suggested but no luck.. (same problems are logged in the event viewer). the ap is connected to a switchport in trunk mode and vlan 1 is the native lan (untagged). the port also is joined to vlan 30 (and others).
Below the new config. Hope you can see an error..
! Last configuration change at 22:56:10 UTC Thu Apr 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Default vlan 1
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
   vlan 50
   band-select
   authentication open
   mobility network-id 50
dot11 ssid Windekind.Gast
   vlan 30
   band-select
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   mobility network-id 30
   wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
   vlan 40
   band-select
   mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
no preamble-short
channel 2452
station-role root
payload-encapsulation dot1h
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
t

Idoc not found in the receiving system

Hi Experts,
In the sending system idoc status is 03 (Data passed to port OK), but in the receiving system the idoc is not there. How to rectify this error?
Thanks & Regards,
Soumya.

Hi Soumya,
Check the RFC connections, becoz in the sending system once the IDOC is sent the status becomes 03 it does not check whether the IDOC has sent to the received system, if there are any errors before sending the IDOC it will not send and the status will be 01, so check the RFC connections at sending and receiving systems.......
Reward points if this helps............
Regards,
Ravi G

SAP ERP - SAP ME - iDOCS - Not received

Dear Experts,
We are trying to send data ( MATMAS iDOC) from ERP to ME.
We used the below transaction in SAP.
1. using BD10 transaction in SAP ( Send material) Idoc was sent
Checks :
We checked in WE05 in SAP and found that Idocs sent is successful
Opened MII ( Queue Monitor) and Found that Idoc was received successfully with ID but Message ( "" sucessfully Queued) Status : Queued
Problem : We are not able to see the material in ME system
No errors found in NWA logs.
Kindly suggest any solution.
Regards
Shankar

Make sure you have the plant id in the idoc. Here are the few place in the idoc that you need to add the PlantID. We're using TN01 as our plant.
<MATMAS03>/ <IDOC>/ <E1MARCM>/ <WERKS>TN01</WERKS>
<MATMAS03>/ <IDOC>/ <E1MBEWM>/ <BWKEY>TN01</BWKEY>
<MATMAS03>/ <IDOC>/ <E1MVKEM>/ <DWERK>TN01</DWERK>

IDOC not receiving in XI

Hi -
Using PI 7.0 and checked all the configurations and read all the related blogs but i don't see the IDOC coming into XI.
Checked the SM58 on R3 and does not show any errors.
I checked the WE02 on XI system and shows a status of 60 and 56. Status 60 says "Basic Type MATMAS05 does not exist" which is true because it does not exist on the XI system but exists on the r3 system.
All the ports on xi and r3 system seem to be fine. i pushed the idoc and shows a status '03' on the r3 side.
Any tips/ideas to solve the issue are greatly appreciated.
Thanks,
Tirumal

Hi,
Go to SMQ2 and try to check the Queue Status .
Did you check this SAP note I referred earlier- 940313
Also -http://help.sap.com/saphelp_nw04/helpdata/en/6a/e6194119d8f323e10000000a155106/content.htm
GO thru each step ..because it will help you to resolve the problem.
Hints-
1) check WE02 and check the status of Idoc in the R/3 system. Is it sent to XI box/port correctly ?check its control record info , in WE19
2) Did you check Partner Profiles - for outbound parameters -check out this
3) Check the SM59 entry in SAP system - pointing to XI box.
4) Check IDX5 transaction in XI box, if eevrything is success in R/3 system
5) check the Business system in XI - is it pointing to correct R/3 system.
Hope this helps,
Regards,
Moorthy

Mail not received by the receiver but successfully sent out

hello sir
i m new to java mail and i have installed one free server from in internet ........i have connected to that server through my programme ..........
i have send mail through my programme .....
from : [email protected]
to : [email protected]
it send it out successfully and showing in the server but it will not been received by the receiver..................can u plz tell me why and what i should do to come out of with this problem so that it will be delivered to the receiver...
thank you
gaurav

I sent like 6 msgs today and all day could not get one freaken message delivered. I have now permenetly turned off iMessage. The service in my opinon is horrible, not reliable and annoying. This is not the first time I couldnt get messages through.
In general iOS5 has caused me more problems then solutions.

IDoc not received in MII

Hi All,
I am using SAP MII 12.1.5 Build 87.
I am facing problem with iDoc Listner we have configured iDoc Listner properly in SAP ERP, SAP NW and in SAP MII.
We are able to send iDoc from SAP but we are not able to receive same in MII.
Port and iDoc Server is giving status connected previously it was working fine in SAP MII 12.1.5 Build 83.
Following are the log details for SAP MII Logger as well as SAP NW Log.
SAP NW Log:
Error processing JRA IDOC message
SAP MII Log:
Error processing JRA IDOC message
Error processing JRA IDOC message [server=xxx, client=xxx]
[EXCEPTION]
java.lang.NullPointerException
at com.sap.xmii.ejb.JRAListenerBean.onMessage(JRAListenerBean.java:130)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at com.sap.engine.services.ejb3.runtime.impl.RequestInvocationContext.proceedFinal(RequestInvocationContext.java:46)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:166)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_StatesTransition.invoke(Interceptors_StatesTransition.java:19)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_Resource.invoke(Interceptors_Resource.java:71)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_MessageListenerType.invoke(Interceptors_MessageListenerType.java:110)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:189)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_StatelessInstanceGetter.invoke(Interceptors_StatelessInstanceGetter.java:16)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_SecurityCheck.invoke(Interceptors_SecurityCheck.java:21)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_ExceptionTracer.invoke(Interceptors_ExceptionTracer.java:16)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.Interceptors_Lock.invoke(Interceptors_Lock.java:21)
at com.sap.engine.services.ejb3.runtime.impl.AbstractInvocationContext.proceed(AbstractInvocationContext.java:177)
at com.sap.engine.services.ejb3.runtime.impl.DefaultInvocationChainsManager.startChain(DefaultInvocationChainsManager.java:133)
at com.sap.engine.services.ejb3.runtime.impl.DefaultEJBProxyInvocationHandler.invoke(DefaultEJBProxyInvocationHandler.java:164)
at com.sap.engine.services.ejb3.runtime.impl.MDBProxyInvocationHandler.invoke(MDBProxyInvocationHandler.java:77)
at $Proxy943.onMessage(Unknown Source)
at com.sap.mw.jco.jra.idoc.JRAIDocExtension$IDocMessageHandler.onMessage(JRAIDocExtension.java:72)
at com.sap.mw.jco.jra.JRA$ReaderThread.sendDirectToMdb(JRA.java:6641)
at com.sap.mw.jco.jra.JRA$ReaderThread.sendAsynchRequest(JRA.java:6601)
at com.sap.mw.jco.jra.JRA$ReaderThread.handleRequest(JRA.java:6771)
at com.sap.conn.jco.rt.DefaultServerWorker$RequestDispatcher.handleRequest(DefaultServerWorker.java:989)
at com.sap.conn.jco.rt.DefaultServerWorker$RequestDispatcher.handleRequest(DefaultServerWorker.java:967)
at com.sap.conn.jco.rt.DefaultServerWorker.dispatchRequest(DefaultServerWorker.java:142)
at com.sap.conn.jco.rt.MiddlewareJavaRfc$JavaRfcServer.dispatchRequest(MiddlewareJavaRfc.java:2927)
at com.sap.conn.jco.rt.MiddlewareJavaRfc$JavaRfcServer.executePlayback(MiddlewareJavaRfc.java:2659)
at com.sap.conn.jco.rt.MiddlewareJavaRfc$JavaRfcServer.playbackTRfc(MiddlewareJavaRfc.java:2478)
at com.sap.conn.jco.rt.MiddlewareJavaRfc$JavaRfcServer.handletRfcRequest(MiddlewareJavaRfc.java:2362)
at com.sap.conn.jco.rt.MiddlewareJavaRfc$JavaRfcServer.listen(MiddlewareJavaRfc.java:2207)
at com.sap.conn.jco.rt.DefaultServerWorker.dispatch(DefaultServerWorker.java:259)
at com.sap.conn.jco.rt.DefaultServerWorker.loop(DefaultServerWorker.java:322)
at com.sap.conn.jco.rt.DefaultServerWorker.run(DefaultServerWorker.java:220)
at com.sap.mw.jco.jra.JRA$ReaderThread.run(JRA.java:7260)
at com.sap.engine.services.connector.jca15.work.TaskImpl.run(TaskImpl.java:255)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:115)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:96)
at com.sap.engine.core.thread.execution.CentralExecutor$SingleThread.run(CentralExecutor.java:314)
Please help me out on this issue.
Regards,
Manoj Bilthare
Edited by: Manoj Bilthare on May 19, 2010 12:57 PM

Hi Manoj,
Once you have configured your Listener have you checked pressing the update button and i dont want to ask you which version of NW SP you have installed as you said it was working for you with Build 83, but nevertheless NW SP Level should not be not less than SP3.
If this doesn't help you,please try restarting your server again.
How about the credential editor have you configured this as well?
Regards,
Sudhir Kumar
Edited by: Sudhir Kumar Shambana on May 19, 2010 10:46 AM

Idoc not received in receiver , sender shows successful in WE02

Hello,
I am sending Vendor from Production to Quality , sender system shows in WE02, idoc status as sucessful. I have checked all ALE settings and they are perfectly fine.
But in receving system I am not able to receive it. In sender , transaction SM58 is showing error:
No authorization to send IDocs with message type CREMAS
Can any one suggest what is the soultion for this scenario?
Thanks,
Madhura

Hello,
Solution for above problem:
After executing transcation SM58, screen will show Function Module as IDOC_INBOUND_ASYNCHRONOUS , put cursor on FM IDOC_INBOUND_ASYNCHRONOUS
, go to EDIT->Execute LUW.
This will solve the problem of authorization.
Thanks,
Madhura

Idoc not received in xi

Hi,
i using idoc to file scenario . idoc are getting posted from sap sucefully i.e status 03 & no entries are found in sm58 .
I am unable to trace the idoc in xi i.e idx5 , sxmb_moni .
I have create port in idx1 for r3 also.
I am unable trace message in RWB .
Plz help me to solve this thread
Thanks,
Sridhar

Hi,
This are the ALE settings,
These will be the Configurations needed in your R3,
1. SM 59 - Create an RFC destination for your XI .
2. We21 -- Create a port for XI
3. We 20 -- Create a partner profile entry for the Outbound IDOCs for XI.
Configuration on XI
1. IDX2 - Import IDOC metadata.
For eg : Lets assume the R/3 system and Xi system are QZA and X7A.
In XI :
Step 1 : In SALE Tcode :
a)Create Logical systems for R/3 and XI.
EG : (QZACLNT100) and (X7ACLNT100).
b) Assign the logical system of XI to Client.(X7ACLNT100)
Both the above options u can find in SALE transaction under SENDING and RECEIVING SYSTEMS tab
Step 2 : In SM59 create RFC destination in XI pointing to R/3(i.e IP address of R/3) (This RFC Destination name shd be same as the Sender LS name)=> QZACLNT100 is my RFC destination.
Step 3: Create the PORT in XI for the Sender system and assign the RFC destination.
In R/3 :
Step 1:
In SALE Tcode :
a) Create Logical systems for R/3 and XI for
b) Assign the logical system of R/3 to Client.(QZACLNT100)
Step 2 : In SM59 create RFC destination in R/3 pointing to XI(i.e IP address of XI) (This RFC Destination name shd be same as the Receiver LS name)=> X7ACLNT100 is my RFC destination.
Step 3: In SALE Tcode under Modelling and Implementing Bussiness Processes-> maintain Disribution Model and Distribute Views.
a)Click on that ,it shall take to Tcode BD64 ,where u can create a Distribution Model.
b)Once you create that ADD MESSAGE type(You have the button at the top), there it shall ask for Receiver and Sender LS and Message type.
c)In Menu Bar EDIT->Generate Partner Profile.
Click on that and press Execute .
This shall create 2 partner profile X7ACLNT100 and QZACLNT100 ,X7ACLNT100(this is the partner number for QZA system) shall have the outbound parameter as CREMAS, and QZACLNT100 is created with no parameters ,you need not worry .
d) Click EDIT->MODEL VIEW->Distribute.
This shall distribute the model and you can see the distribution mode aslo getting created in XI system.
This configuration shall surely help u out as it worked out for me.
Configurations required for IDocs in R/3
In your XI system, you need to do the following.
1. Create a RFC destination to your R/3 system
2. Create a port in IDX1 of your XI system and use the RFC destination in step1.
3. Try importing a idoc metadata thru idx2 transaction to check whether the configuration is correct.
4. In your SLD configure the technical system and business system. The technical system should hold the logical system name you have in your R/3 system client.
5. Import the business system and you can use it in your configuration scenario.
Please also refer below links for details.
Go thru this-
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/877c0d53-0801-0010-3bb0-e38d5ecd352c
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/877c0d53-0801-0010-3bb0-e38d5ecd352c
SAP R3 ->Legacy system including master data using XI
Regards,
Phani

Idoc Not received on MII Message Listener

Hi All,
I am trying to post Idoc from R/3 to MII Server , but some how I am not getting it
I have configured Destination, Parter, Partner Profile on the R/3 and Message Listener on MII.
When I am trying to send Idoc from R/3 using BD10 transaction (Idoc type MATMAS), Idoc Status as 03 in WE02 transaction , but I the MII server does not show up for this.
Even the Failed Messages is showing no results.
Am I missing some thing here.
Any help is appreciated.
Kind Regards

I got the issue,
The problem was Partner was wrongly selected.
Thanks

IDoc not received by the Webmethods

Similar Messages

Maybe you are looking for