Idoc ROUTING_CREATE01 and rate routing

Hello,
Is it possible to create rate routing with idoc ROUTING_CREATE01, so far I can create only simple routing.
Thanks for your answer.

Hi,
For rate routing:
use this BAPI: 'BAPI_ROUTING_CREATE' for creating Rate Routing
Regards,
Kumar(Reward if helpful).

Similar Messages

Standard routing and rate routing

Hi All,
Can someone tell me what tables I should use to get the standard routing and rate routing for the query?
Thanks
Edward.

Dear,
Yes you are right.
The main difference between routing and rate routing is you can not create parallel sequence in rate routing CA21 only nothing else.
There are lot of different opinion on this topic but there is no too much difference in them only we use rate routing in REM and normal in Discrete manufacturing.
Also check this thread ,
Difference between routing and rate routing
Hope clear to you.
Regards,
R.Brahmankar

Routing and rate routing

Hi Gurus,
Please explain me the difference between Routing and rate routing in details
Thanks in advance
Rupesh

Hi,
Functionality of Routing and rate routing is similar.
Routing: It defines the sequence of operations that should be carried at a work center to make up a product.
Routing is one of task list in PP module to carry out the production of finished and semi finished parts. it consists operation sequence which requires for manufacture finsihed and semi finished parts like operation 10. 20, 30...
It is mostly used in Discrete Manufacturing
Rate Routing: A routing for whose operations the production quantity and a fixed duration has been defined. Thus the production rate is also defined.
Rate routings are used when you plan on a quantity basis, for example in repetitive manufacturing.
With regards
Ram Kumar

What's the difference between routing and rate routing

As we all know that routing normally used in discrete manufacture, and rate routing used in REM, one of my client, the just use routing for REM instead of rate routing, are there any gurus can tell me some detail information about them?
Thanks!
Eric

Hi,
对于routing和rate routing来说，区别并不是很明显，但从流程的角度来说，routing适用于所有的离散型制造业，而rate routing适用于重复制造业！
如果非要找出差别的话，就是routing可以定义并行序和可选序，而且rate routing只能定义并行序！
具体的使用差别可以参考如下链接：
http://help.sap.com/saphelp_45b/helpdata/en/03/bb1d0ca6e811d189010000e8323492/frameset.htm

Difference between routing and rate routing

frndz,
Pls tell me the difference routing and rate routing.
regards,
Srini

Dear ,
[Rate Routing:]
1.A routing for whose operations the production quantity and a fixed duration has been defined. Thus the production rate is also defined.
2.Rate routings are used when you plan on a quantity basis, for example in repetitive manufacturing.
3.A rate routing has the same structure as a routing. You can assign a rate routing to a material to be produced. It can have prallel sequences.
[Routing]
1.Routings are used directly in production orders for a material.
2.A routing can be used without restrictions. Some functions from other task list types such as rate routings and inspection plans are also available in routings.
3.As well as a standard sequence a routing can also have parallel and alternative sequences. You can assign a routing to a material to be produced.

Differences between rate routing and reference rate routings?

Hello PP members:
I would like to differences between rate routing and reference rate routings
Thanks for your time,
Thanks Again,
Suren R

Hi Mr.Suren,
As explained by other friends Routing is used in Discrete manufacturing and Rate routing is used for REM-Repetitive manufacturing.
In addional to these types SAP has given 2 more types
1.Reference operation set -Used in Discrete manufacturing.
2.Reference rate routing - Used in REM.
If similar rate routing is been used for producing many materials,then instead of entering(these steps) in rate routing of each material you create a refrence rate routing and you enter the work centres used and the other details.After saving you get a group counter number showing reference rate routing is saved with group XXXXXXXXX.
When you are creating rate routing for a material say A ,after giving the name and plant details in the top you will be able to see an icon "copy from" and you can select the radio button for reference rate routing and give the group counter number. or else without giving it here you have got an option to select the reference rate routing after entering into the operation screen also.
In that particular page in operation overview screen,there will be an icon copy,there you can click that icon and you can give the reference rate routing group counter number and very easily you can create rate routing for N number of material.
Likewise you can use reference operation set while creating routing for a material in Discrete manufacturing.This basically reduces the time in creating routing or rate routing for materials in Discrete & REM respectively
CA01,CA02,CA03-Create,Change,display (routing) respectively.
CA11,CA12,CA13-Create,Change,Display reference operation set Respectively.
CA21,CA22,CA23-Create,Change,Display rate routing respectively.
CA31,CA32,CA33-create,change,display reference rate routing resp.
I hope this will help you.
If useful reward your points.
Thanks & regards
Karthik.

Raouting, Rate Routing and Cost run Problem

We have changed the our process from routing to rate routing.
But while doing the cost run - CK40N, the sytem is considering the routing in stead of rate routing.
Please advice.
Regards
Pranav

Dear Pranav,
1.Check what selection ID has been assigned in the quantity structure control tab(for the costing variant that is used for costing in
CK40N) for routing selection,If it's 01 means,then check with selection ID 02 where the first priority is assigned for routing type R.
(In standard SAP selection ID 01 by default has first priority to routing - N and then further prirority to rate routing - type - R).So
assuming selection ID 01 is assigned and a product has both routing(task list type - N) and rate routing(task list type - R),now at
the time of costing the system picks up the routing by default as the first priority is set for routing.
2.Also check whether the task list type and the corresponding group and group counter has been changed in the production
version for inhouse manufactured product either in MM02-->MRP4 view or else in C223.
Check and revert back with your further queries.
Regards
Mangalraj.S

Sequence selection in Rate Routing

hi,
In Normal Routing in sequence overview - extras - new entries we can find the option of creating a Parallel or Alt sequence, but in Rate routing there is no way to select the type of Sequence. It by default shows Parallel sequence.
Pl. let me know the step by step proceduer to create a Alternate sequence in Rate routing.
regards

Dear Rishi,
We cant create any alternative sequence for a rate routing.This is one of the difference between routing and rate routing.
Rate routing supports only standard and parallel sequence.
If alternative sequence is present in a routing,then at the time of order creation the system gives a pop to select for alternative
sequence or to skip it and proceed.
For this under OPL8,for plant order type combination the field sequence exchange should be having value 2 - manual selection.
Creating production version or sequence in my understanding depends on the business requirement.
Check and revert
Regards
S Mangalraj

Difference between Routing & Rate Routing

Hi All,
can anyone tell me difference between Routing & Rate Routing? can we use routing for REM? if no, then what will be the effect?
Thanks,
Rinky

Hi Rinky ,
Routing and rate routing are task list in broad manner .
standard task list: Describes the worksteps necessary to produce a material or perform an activity without reference to an order.( that means they are created without reference to order )
Essential objects of a task list are header, operations, material component allocations, production resources/tools and inspection characteristics.
Together with specific dates and quantities, task list data forms an important part of the order.
The following task list types exist in the R/3 System:
routing
reference operation set
rate routing
reference rate routing
inspection plan
maintenance task list
standard network
master recipe
Routing is created with ca01 and rate routing by ca21 .
Routing is used in discrete manufacuting and rate routing in repetitive .
Rate routing generally has only one operation and prod line instead of work centers and operations in routings .
Both routings can be used for scheduling , cosing and capacity planning .
Hope this was helpful answer !
Neal
Edited by: Neal Gibson on Jun 30, 2008 11:46 AM

Routing & rate routing

hello everyone,
myself rekha bamgude,i want to know difference between routing & rate routing?

Hi rekha to get a quick (or any) response, create your new discussion in a space related to your query. This way it will be visible to topic experts who will then see and reply to it.
Please move this thread to the relevant forum Enterprise Resource Planning (SAP ERP)
as you mention
i want to know difference between routing & rate routing?
Many times we told this word (Search before you post ).
please see this thread for more details.
Difference between routing and rate routing
poorna

EDI - 753Routing Request and 754 Routing Instructions transactions- what SAP ECC6 EDI output type, msg type, msg code, basis idoc is best practice to generate the idoc?

One of our Trading Partner wishes to implement the 753 Routing Request and 754 Routing Instructions. Can anyone give me best practice answer the following Questions? We are on SAP ECC6 R3
What Application? i.e. V2, V7?
What output condition to use? i..e. LALE, LAT2, SEDI????
What Message type? i.e SHPADV?
What Basic Idoc Type? i.e SHPMNT05?
What Message Code? i.e. SHPM?
What Process Code? i.e. SHPM??
What Function Module? i.e. IDOC_OUTPUT_SHPMNT??
Does the SAP Transpotation Module have to be configured for this to be implemented?
Your comments are greatly appreciated, we have until Nov 1 to be compliant?

Good Morning,
While I did not get any responses from my question, yes, I was able to determine what needed to be configured. I hope the below will help you: This is for SAP ECC6
The output application for the 753 Routing Request is "V7"
The output type is "SEDI"
Transmission medium is "6"
The Basic Idoc type is "Shipmnt05"
when setting up your Partner Profile (WE20) add:Message Partner Role "SP" with Message type "SHPADV', Message coed "753", Basic Type "SHPMNT05", Message Control add Application "V7", Message type "SEDI", Process Code "SHPM".
also http://scn.sap.com/thread/698368 pages 14 and 15 were helpful.
I have not configured the Inbound 754. For now the inbound 754 Routing Instructions will be emailed to our traffic department.
Thank you,
Have a great day,
jane

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

Problem in automatic rate routing selection

Dear all,
I am using REM and according to that I have maintained REM profile in Material Master, rate routing, line hierarchy, production version, but the time of scheduling of planned order, system is saying " The automatic selection of routing is not possible".
I suppose I am missing some configuration.
As also, I have already done the same scenario in other server.
If u have any suggestion then pl. forward me.
Thanx,
Das

Dear SAP PP,
1.Check whether have you included the check box for REM allowed indicator in the production version.
2.Also ensure you have assigned the rate routing option for detailed planning and the correct group and
group counter in the production version.
3.Check the valdiity dates of the rate routing,try to create a planned order in some advanced future date
so that your rate routing is valid for the planned order start date.
4.Check the status and the usage of the rate routing.
Regards
Mangalraj.S

Receiver determination(or Interface determination) and conditional routing

I have a flat file to flat file scenario. Based on the input file content, I want to route data to the receiver.
My source flat file contains several IDOC details. Assume two fields FIELD1 and FIELD2 in different segments of the IDOC. My requirement is if FIELD1 of an IDOC = "US" and FIELD2 of the same IDOC = "CA", then that IDOC's details needs to be passed to the receiver.
I have implemented the above condition at interface determination.
But the problem is:
Assume there are 3 idocs in the input file.
FIELD1 of IDOC[1] = 'US' and FIELD2 of IDOC[1] = 'GL'
FIELD1 of IDOC[2] = 'UK' and FIELD2 of IDOC[2] = 'EN'
FIELD1 of IDOC[3] = 'BR' and FIELD2 of IDOC[3] = 'CA' .
Now none of the IDOCs in the input satisfy my requirement and hence the message mapping should not be called at all. But in my case its failing because FIELD1 of IDOC[1] and FIELD2 of IDOC[3] together are satisfying the condition and hence the message mapping is called.
But I need to check this condition IDOCwise. Both the conditions to be satisfies in the same IDOC.
I am thinking that contexts are not being taken care.. It just see the whole file together and not IDOCwise.
Can someone help me on the same. Please let me know if more information is required.
Thanks,
Shobha

>
Shobha HB wrote:
> I have a flat file to flat file scenario. Based on the input file content, I want to route data to the receiver.
>
> My source flat file contains several IDOC details. Assume two fields FIELD1 and FIELD2 in different segments of the IDOC. My requirement is if FIELD1 of an IDOC = "US" and FIELD2 of the same IDOC = "CA", then that IDOC's details needs to be passed to the receiver.
>
> I have implemented the above condition at interface determination.
>
> But the problem is:
> Assume there are 3 idocs in the input file.
> FIELD1 of IDOC[1] = 'US' and FIELD2 of IDOC[1] = 'GL'
> FIELD1 of IDOC[2] = 'UK' and FIELD2 of IDOC[2] = 'EN'
> FIELD1 of IDOC[3] = 'BR' and FIELD2 of IDOC[3] = 'CA' .
>
> Now none of the IDOCs in the input satisfy my requirement and hence the message mapping should not be called at all. But in my case its failing because FIELD1 of IDOC[1] and FIELD2 of IDOC[3] together are satisfying the condition and hence the message mapping is called.
>
> But I need to check this condition IDOCwise. Both the conditions to be satisfies in the same IDOC.
>
> I am thinking that contexts are not being taken care.. It just see the whole file together and not IDOCwise.
>
> Can someone help me on the same. Please let me know if more information is required.
>
> Thanks,
> Shobha
The ideal solution to your scenario is to redesign the interface as below;
1. Receive the file.
2. Do a 1: N mapping (this should split your message into multiple Messages)
3. On this message you can do the required check. Now only the required field for the particular IDoc will be part of the check and it will not mix with other Idocs.
Will this do? Else please provide more details

EDI ANSI X12 and relavent IDOC types and messages...

Hi ,
    Is there any place where we can get the relevant Idoc types and messages for EDI Transacitons below:
210 -Motor Carrier Freight Details and Invoice
240 -Motor Carrier Package Status
753 -Request for Routing Instructions
754 -Routing Instructions
816-ORGANIZATIONAL RELATIONSHIPS
828-Debit Authorization
846- Inventory Inquiry/Advice
870-Order Status Report
Could you please help me?
Thanks and regards,
gowri

EDI ANSI X12 and relavent IDOC types and messages...
Posted: May 25, 2006 8:44 PM        Reply      E-mail this post
Hi Ravi,
     Thanks a lot for the reply. I have already checked this. In the ittoolbox.com is having some info about 214 but not about 210 and 240. I have already gone through the sapgenie.com but could able to get the relevant info on below transactions.I am basically looking for relevant idoc types and messages in SAP for the below ansix12 transactions .
Is there any place where we can get the relevant Idoc types and messages for EDI Transacitons below:
210 -Motor Carrier Freight Details and Invoice
240 -Motor Carrier Package Status
753 -Request for Routing Instructions
754 -Routing Instructions
816-ORGANIZATIONAL RELATIONSHIPS
828-Debit Authorization
846- Inventory Inquiry/Advice
870-Order Status Report

Idoc ROUTING_CREATE01 and rate routing

Similar Messages

Maybe you are looking for