IDOC Serialization & Synchronous Scenarios with AAE

Hi Folks,
I have queries reg Advanced Adapter Engine (AAE):
1) Can we do the Synchronous scenarios through AAE.
2) How can i do the IDOC serialization. How AAE helps in that.
Am using PI 7.3 ...Can you please mention the possibilites for the above queries.
Thank you!!
Regards,
Sekhar

MDM Learn wrote:
Hi Folks,
>
> I have queries reg Advanced Adapter Engine (AAE):
>
> 1) Can we do the Synchronous scenarios through AAE.
Already supported as part of 7.1 / 7.11 so dont see any problem here
>
> 2) How can i do the IDOC serialization. How AAE helps in that.
>
> Am using PI 7.3 ...Can you please mention the possibilites for the above queries.
>
> Thank you!!
>
> Regards,
> Sekhar
the above should be very much supported if you are using the Java IDoc adapter. For serialization use qRFC in SAP partner profile

Similar Messages

IDoc-to-File scenario with external Partner ... PCK necessary?

Hi all,
I have a question concerning to a IDoc-to-File Scenario with an external Partner. Here is a short Description of the Scenario:
The SAP ERP System creates an IDoc which should be send to the SAP Integration Server. The Integration Server respectively the IDoc-Adapter transform the IDoc in IDoc-XML. The Integration Server executes a Mapping and so on. In the final step the Integration Server should send the XML-File to a FTP Server in New York (external Partner) with the File/FTP-Adapter.
Have I to install the Partner Connectivity Kit at a Server in New York or is it working without the PCK? Which are my possibilities?
Thanks for your help
with kind regards
Christopher

Hello,
If the FTP server has connectivity to XI and if the
port is open XI can directly do the FTP using File
Adapter.
Thanks,
Himadri
Hi,
thanks for your quick answer.
What means "connectivity to XI"? Our SAP-Environment is in Germany and the FTP-Server is in New York. Is it enough to open the port in the firewall?
Thanks for your answer
Christopher Kühn

IDOC to FILE scenario With Screen shots

CAN YOU PLEASE SEND US THE DETAILS OF IDOC to FILE scenario With Screen shots and do the needful for me

Hi Surya,
I thought i will just share a few basic thoughts that you need to take care while doing an IDOC to File Scenario. Just see if it helps you in anyways.
While doing an IDOC -> XI -> File scenario, The Points to noted are:
1. You dont need a DT, MT or a message interface for the IDOC as it itself acts as the Message Interface.
2. You import the IDOC and use the same in your mapping.
3. In this configuration note that you dont have a sender agreement as you dont have a sender IDOC adapter.
If it is that you wanted to send an IDOC from XI (File to IDOC) , then in this case:
points 1 and 2 will remain, but the 3 will not. You will need a sender agreement for the file and a receiver agreement for the IDOC.
IDOC -> File scenario ref:
<a href="/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters scenario</a>
File -> IDOC ref:
<a href="/people/anish.abraham2/blog/2005/12/22/file-to-multiple-idocs-xslt-mapping to IDOC</a>
To be able to trigger your IDOC from the SAP ISU system, you will have to set the partner profile in we20. Select your Business System (mostly under Logical system) and then create Outbound entries for whichever IDOC you want to trigger.
You define your basic type also in your partner profile settings, Please go thru the following links to get a better idea about partner profile:
http://help.sap.com/saphelp_nw04/helpdata/en/dc/6b833243d711d1893e0000e8323c4f/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/dc/6b7cd343d711d1893e0000e8323c4f/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/32/692037b1f10709e10000009b38f839/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/5e/b8f8bf356dc84096e4fedc2cd71426/frameset.htm
Also, I would suggest that you go through this blog by michal if any issue arises,
/people/michal.krawczyk2/blog/2005/03/29/xi-error--unable-to-convert-the-sender-service-to-an-ale-logical-system
/people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions
Also have a look at these forum threads...
IDOC TO FILE SCENARIO
idoc to file scenario
I hope this helps.
Regards,
Abhy Thomas

IDoc to soap synchronous scenario with BPM

Hi,
I am working on IDoc to soap synchronous scenario using BPM. Here i am facing lot of soap exceptions in my production system. I handled the exceptions. The data getting excuted for the first time, the same data(just changed the description)is giving exceptions for the second time. Please let me know why the exceptions are getting, and different type of exceptions and solutions for the same.(Blog also is fine)
Thanks & Regards,
Pragathi.

The data getting excuted for the first time, the same data(just changed the description)is giving exceptions for the second
time.
Ideally you should not get an exception for the same data....can you tell is the description and where are you getting the exception...is it a part of the SOAP message or some object?
An exception might have occured because the description would be something unacceptable by the target application.
and different type of exceptions and solutions for the same
there would be many blogs....your thread would be spammed...better make a search on SDN with exception text that you are getting.
Regards,
Abhishek.

Message flow in SAP PI 7.31 JAVA only for ABAP Proxy synchronous scenario with Oracle DB

Dear Experts,
I am working on a synchronous scenario Sender ABAP Proxy <===> SAP PI 7.31 JAVA only <===> Oracle Database.I have successfully
configured all the proxy configurations as well both Sender SOAP and JDBC receiver channels are showing no error when pinged from
Cc monitoring in NWA.
1.During testing at Tx SPROXY , I am triggering a message and after 5 minutes I receive an PARSING error message with 2 messages in ECC
local IE i.e. Tx SXMB_MONI.
Note : In NWA , I can see only 1 message that too in cancelled status.
2.Seeing the trace of the messages I assume that the messages have not moved from sender ECC system. I am still confused with flow of message
from the Message Audit log. Audit log of error messages.Could any one share the full Audit log of a successful message generated in SAP PI 7.31 JAVA only.
3.I observed that the QIN Scheduler status in ECC is in INACTIVE status. There is no queue id for 2 messages generated in ECC. Does
it should in ACTIVE status in Tx SMQR..
Regards
Rebecca

Hi Thomas,
Valuable inputs..
1. Since I don't have any audit log for successful message, would you be able to share referring to the
below screenshot whether the message was put into receiver JDBC adapter and JDBC adapter tried to retrieve the Select response from Oracle Database.
2.I have done some setting in Advance mode of the receiver JDBC to increase the time out and other parameters as per SAP note but still the issue is same. If you perhaps have some experience in such scenarios, please share some input so that I can ask the Oracle Database administrator exactly what is required from our side.
3.Regarding the slow response from Oracle , there was some suggestion that the datatype of the request and response should match the column name of the Oracle database. I did that.. Do you have any more suggestion that may be hampering the generation of the response message from the Oracle like SAP note or document.
Regards
Rebecca

Idoc to proxy scenario with an acknowledgment

Hi ;
I have to implement a IDoc to abapProxy scenario but an application acknowledgment must be return so IDOC status will be set.
How can i understand whether an application error exists while abapProxy is executing or not in status of IDOC?
Do I need to create and sent back new IDOC to the sender system in abapProxy code?
Thanks.

Hi,
See if you just want the ack for your IDOC coming from r/3 to XI, then you can use ALEAUD01 IDOC and you can configure it by running report IDX_NOALE in XI system..........
But if you want status change for appl error occuring in ABAP proxy system, then i think you will have to use a BPM for it.........you will have a recive step for getting your IDOC, then a transforamtion step for IDOC to proxy mapping, then a synch send step for sending proxy req and getting proxy response, then a transformaton step for mapping the proxy response to SYSTAT01 IDOC in r/3 for changing the IDOC status depending on success or error for your proxy response, then a send step to send this IDOC to r/3 system...............keep teh IDOC number in proxy req and proxy response so that you can use it in SYSTAT01 IDOC for sending it to r/3 and changing your IDOC status.
Regards,
Rajeev Gupta

Character Encoding for IDOC to JMS scenario with foreign characters

Dear Experts,
The scenario is desribed as follows:
Issue Description:
There is an IDOC which is created after extracting data from different countries (but only one country at a time). So, for instance first time the data is picked in Greek and Latin and corresponding IDOC is created and sent to PI, the next time plain English and sent to PI and next Chinese and so on. As of now every time this IDOC reaches PI ,it comes with UTF-8 character encoding as seen in the IDOC XML.
I am converting this IDOC XML into single string flat file (currently taking the default encoding UTF-8) and sending it to receiver JMS Queue (MQ Series). Now when this data is picked up from the end recepient from the corresponding queue in MQ Series, they see ? wherever there is a Greek/latin characters (may be because that should be having a different encoding like ISO-8859_7). This is causing issues at their end.
My Understanding
SAP system should trigger the IDOC with the right code page i.e if the IDOC is sent with Greek/Latin code page should be ISO-8859_7, if this same IDOC is sent with Chinese characters the corresponding code page else UTF-8 or default code page.
Once this is sent correctly from SAP, Java Mapping should have to use the correct code page when righting the bytes to outputstream and then we would also need to set the right code page as JMS Header before putting the message in the JMS queue so that receiver can interpret it.
Queries:
1. Is my approach for the scenario correct, if not please guide me to the right approach.
2. Does SAP support different code page being picked for the same IDOC based on different data set. If so how is it achieved.
3. What is the JMS Header property to set the right code page. I think there should be some JMS Header defined by MQ Series for Character Encoding which I should be setting correctly) I find that there is a property to set the CCSID in JMS Receiver Adapter but that only refers to Non-ASCII names and doesn't refer to the payload content.
I would appreciate if anybody can give me pointers on how to resolve this issue.
Thanks,
Pratik

Hi Pratik,
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/502991a2-45d9-2910-d99f-8aba5d79fb42?quicklink=index&overridelayout=true
This link might help.
regards
Anupam

SOAP to RFC synchronous scenario with File without BPM

Hi Folks,
I have a requirement that has to be done with out BPM!!!
Requirement:
Soap will trigger the request to SAP(RFC) and SAP sends the response to a file and then after SOAP has to recieve the ACK from PI.
1) Can we do this by without using BPM
2)Can we use without BPM module entries for SOAP Sender
Please suggest and help me out in this
Thanks in advance,
Regards
vivek

Hi Vivek,
Why not have the SOAP interface defined as synchronous?
You can avoid using BPM that way.
Best Regards,
Ravi

IDOC to File scenario with multiple directories on same FTP.

The scenario is IDOC -- to FTP (Receiver file adapter). Based on the condition in the sender IDOC say if EIDKA01-BSART = Y than the directory path on FTP server is 'A' ELSE 'B'.
There is only one reciever service defined for the FTP server in the Integration Directory. Its not multiple receiver scenario.
How do we do this?
Thanks

Hi !
Just create an UDF in graphical mapping and put this code inside:
DynamicConfiguration conf = (DynamicConfiguration) container.getTransformationParameters().get(StreamTransformationConstants.DYNAMIC_CONFIGURATION);
//get Key of Directory
DynamicConfigurationKey keyD = DynamicConfigurationKey.create( URLFile, "Directory");
//Replace value of Directory
conf.put(keyD,dir);
where "dir" contains the destination path depending on the EIDKA01-BSART value. When this code executes, if the receiver file adapter has the adapter-specific attributes (directory) checked, then it will set the "directory" value to the one specified in the "dir" variable.
Regards,
Matias

How can we do the Testing in Idoc to File Scenario( With out using We19)

Hi All,
As all we know we can generate the Idocs from SAP R/3 to XI using the change Pointers,this we will apply in Production time.
But as of now in the Test system we can'd do it daily.
So we have already created materials in the SAP R/3 system.
I want to send the Idoc to XI by selecting some n number of materials.means i want to generate the Idoc for materials.this is like i have to do repeatedly for testing purpose.
Is there any T-code
How can we do this
Regards

Hi Vamsi,
   For the Message Type ORDERS you can configure Output Type (txn NACE) for IDoc generations and then you can trigger the IDoc using transaction WE15.
Selection Parameter will be as follows
Output application: This will be from Output Type
Object key          : Order Number
Output type         : Output Type name, that you configured
Transmission medium : A
Check the checkbox "Send Again".
Thanks,
Punit

SOAP to RFC synchronous scenario with File

Hi,
My scenario is
Java application is sending SOAP message to PI and PI should route that message (after converting SOAP message to XI message) to RFC.
2) After receiving the response from RFC PI should send the response to java application. Now here comes the little tweak, we need to map RFC response to File as well apart from sending SOAP response message (which is generated after mapping RFC response message to Java application response structure) back to Java application.
Is it possible without BPM?

Without BPM you can try below approach, but i would recommend you to use BPM.
Develop SOAP---->PI(rfc look up) -
> SOAP/JAVA application
map RFC loop up response to SOAP receiver and JAVA application/.
Regards,
Raj

Doubt in idoc 2 file scenario

Hi,
I want to create idoc 2 file scenario with out any Transformation.
In that case how/what to create Data type for receiver.
I want to receive the same idoc in the receiver folder/Directory (like XML file) with out any transformation.
Thanks
Ruban

Hi,
For this scenario you need to create the Data type structures as similar to IDOC type and just have to transfer to file without FCC.
It will transfer the IDOC data as it is in XML format
refer
/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters - IDoc to File
/people/venugopalarao.immadisetty/blog/2007/01/24/troubleshooting-file-to-idoc-scenario-in-xi
https://www.sdn.sap.com/irj/sdn/wiki?path=/display/xi/error%2bhandling%2bin%2bfile-idoc%2bscenario
(Just avoid using FCC conversions on receiver file adapter in above scenarios)
Thanks
Swarup
Edited by: Swarup Sawant on Mar 24, 2008 6:15 PM

Real time idoc to file scenario - URGENT!

Hi all,
I have a real time idoc to file scenario with the idoc structure as below:
WP_PLU03
   IDOC
     Begin
     EDI_DC40
     E1WPA01
        E1WPA02
Now as can be seen, EDI_DC40 is the header record common for the eniter idoc. But the segment E1WPA01 will repeat for each item sent from R/3. E1WPA01 in turn has many segments within it whcih corresponds to that one item.
Now the problem i am facing is, I did the mapping for all required fields from E1WPA01 to my file structure and it works fine if i send one 1 instance of E1WPA01. But when i send multiple instance of E1WPA01 for each item, my result in teh file should be 1 line of record for each E1WPA01. But this doesnt happen. It takes allE1WPA01 as 1 and gives only one record in the file.
How can this be overcome? this is a very common requirments? did i miss anything in the configuration?
Thnaks,
Yash

Hi Matias,
I have two instances (may be much more than 2) of the same segment in the idoc (E1WPA01) and each instance should create a new root in the target message structure as in the link below
Link: [http://img299.imageshack.us/my.php?image=image3ct6.png]
I have mapped the segment E1WPA01 with the root like this:
Link: [http://img176.imageshack.us/my.php?image=image2of6.png]
Hence it creates 1 root for each segment. But for complex mappings such as:
Link: [http://img337.imageshack.us/my.php?image=image1yu1.png]
the 2 input parameter to the UDF - KONDART and KONDWERT - the queue can be seen. the problem which i m facing here is in this queue, values from both the instnace of the segment E1WPA01 is taken together where each instance should be processed seperately. The first 4 values in the top queue(till VKP0) belongs to the filed KONDART of the 1st isntance of the segment and the 1st 4 values of the below queue (till 17) belongs to the field KONDWERT. Similarly the remaining belogns to the other segment. My logic in UDF is built taking only one instance at a time. Is there anyway i can distinguish between the two instance within my UDF?
I hope u understand my problem here.
Thanks,
Yash

Jdbc-rfc synchronous scenario

Hi...All,
we r plaing to do JDBC-RFC Synchronous Scenario with out BPM,please tell me any settings are required for this scenario.any body is having any links regarding this type of scenario pls share with me...that is helpfull for me...
thanks in advance,
Pasi.

Hello Pasi,
JDBC-RFC Synchronous Scenario with out BPM,
Go through this links...
JDBC Sync - RFC Sync Scenario without BPM
File - RFC - File without a BPM - Possible from SP 19.
JDBC-RFC-File
Re: jdbc-rfc synchronous
/people/yining.mao/blog/2006/09/13/tips-and-tutorial-for-sender-jdbc-adapter
/people/siva.maranani/blog/2005/09/16/xi-how-to-on-jdbc-receiver-response
/people/jin.shin/blog/2006/02/07/multi-mapping-without-bpm--yes-it146s-possible
http://help.sap.com/saphelp_nw04s/helpdata/en/22/b4d13b633f7748b4d34f3191529946/frameset.htm
http://help.sap.com/saphelp_nw2004s/helpdata/en/22/b4d13b633f7748b4d34f3191529946/content.htm
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3867a582-0401-0010-6cbf-9644e49f1a10
JDBC-RFC Scnario mapping problem
Thanks,
Satya Kumar
JDBC---RFC will Support Sync?????????

IDOC to SOAP synchronous scenario

Hi All,
We have an IDOC to SOAP synchronous scenario in which IDOCs are sent to SOAP by calling a service and then SOAP sends a response back to XI . The response is not sent to SAP- R3. Please suggest on this
Thanks

Hello Rajesh,
Thanks for your good justification.
Here I have also replicated same kind of scenario and having same kind of issue.
One thing just wanted to confirm - Even though SOAP adapter expects HTTP 200 response back from webservice, still SOAP channel is getting into red with following , and as we have Alert configured ...Alert mail also receiving as part of Error only. So How can we avoid that response ? Is there have any parameter to handle or suppress the response back?
Thanks!
Goutam

IDOC Serialization & Synchronous Scenarios with AAE

Similar Messages

Maybe you are looking for