Idvd ejects the disk during the "multiplexing and burning" / "writing lead-in" portion. When I check, there's nothing on the disk

idvd ejects the disk during the "multiplexing and burning" / "writing lead-in" portion. When I check, there's nothing on the disk.

What brand and type of disk are you using? What speed are you burning at? Are you able to create a disk image of the project?
Try this basic troubleshooting fix:
1 - delete the IDVD preference file, com.apple.iDVD.plist, that resides in your
User/Home/Library/ Preferences folder.
2 - delete IDVD'S cache file, Cache.db, that is located in your
User/Home/Library/Caches/com.apple.iDVD folder.
3 - launch IDVD and try again.
NOTE: In Lion and Mountain Lion the Home/Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.

Similar Messages

Is there a way to resort an ipod touch to the point before a restore was done on it? It is telling me there is nothing in the icloud and I need to reset it back up.

s there a way to resort an ipod touch to the point before a restore was done on it? It is telling me there is nothing in the icloud and I need to reset it back up. The reset was done before I could backup the icloud and itunes to the computer and it wasn't done with my permission.

You may be able to get some info off the restored iPod by:
via How to perform iPad recovery for photos, videos
Wondershare Dr.Fone for iOS: iPhone Data Recovery - Wondershare Official
http://www.amacsoft.com/ipod-data-recovery.html
iPod recovery software to restore lost music files
http://www.pcrecoverytools.com/ipod-data-recovery.html
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

My iPad mail shows 5 letters in my inbox, but when I check there is nothing that shows new letters. How do I get rid of the "5" showing on my home page? My home computer has no new emails either.

My home page shows "5" new emails but when I go to my mail account there are no new letters. How do I get rid of the "5" on my home screen. My computer and other email accounts show no new ones. Help.

Have you tried deleting the account and re-installing?

IDVD ejects during multiplexing and burning

Hi folks,
I've used iDVD previously (several times) to create DVDs of movies I've created in FCE4. Today, the program goes so far, then ejects the disk during the "multiplexing and burning" / "writing lead-in" portion. When I check, there's nothing on the disk. Anyone every experience this? And, if you know, please advise as to how I might fix the problem.
Thanks very much for your expertise.
Vic

Multiplexing Error
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W

HT1386 I downloaded new version of itunes and now when I connect my ipad to sync there is not sync function and there is nothing on the left side of the screen like before.

I downloaded new version of Itunes to my ipad2 and now I can't find sync button. There is nothing down the left side to pick device, etc. The screen is completely blank. Help

if your using windows, try this.

IDVD ejects disk during multiplexing and burning

Having burnt many DVDs previously, I have suddenly started struggling.
Having edited in FCE HD v3.5.1, I export to Quicktime and then build the dvd as normal in iDVD.
The project has no errors and then I burn it using Verbatim 16x certified 4.7GB/120 min Advanced AZO+ DVD-R disks.
During Multiplexing and burning (with between 1 and 3 mins left, it ejects the disk saying saying done but nothing is burnt.
To try to remedy this, I have set the burn speed to both 2x and 1x. I have also turned the computer off, removed all cables and battery, held down the power button for 10secs then rebuilt and retried. Still nothing.
I saved a disk image but I don't know how to then make that into a burnt dvd. Any advice on that would be appreciated but moreover, I'm sure I shouldn't have to jump through so many hoops to burn a dvd - Mac's should just work shouldn't they.....?!

Here's even more of an update, with no joy....
to refresh, I have a macbook pro 15" - the older one with the silver keys.
I make 3 min movies in FCE then export using quick time conversion and try to burn with iDVD.
The problem: I can burn data CDs but i can't burn a DVD anymore. This seemed to start after the update to 10.5.7. At that point I tried to fix it with no joy so due to deadlines, used another machine! Now a few months later, i come back to it and still no joy.
I have reset the PRAM
I have reset the CMR
I have upgraded to Snow Leopard
I have sprayed compressed air into the drive
I have reduced the burn speed to 1x
But still I can't burn a dvd. When iDVD goes through the stages, everything is OK until it gets to multiplexing and burning, it says it is 'writing lead in' and has 1 min left (or 2 mins when burning at 1x). Then the blue status line suddenly goes all along and the machine spits the dvd out saying done. (although iDVD does not revert to beginning of the process, it kind of freezes).
idvd version 7.04 if I hadn't said before.
Please help, I'm despairing....

When my project is in the multiplexing and burning stage, with 3 minutes left, it will eject the dvd. what do I need to do different of fix?

When my project is in the multiplexing and burning stage, with 3 minutes left, it will eject the dvd. what do I need to do different of fix?
I've tried it a couple different movies and it has done this each time with 3 minutes left. What do I do??

Hi
Where did the original movie come from
• miniDV tape Camera
• other Camera - in what codec if so
• from download - in what codec if so
and
How did You go from this
• via iMovie - how
• via FinalCut - how
• direct into iDVD ?
Did it play OK in iDVD Preview ?
Did You Save as a DiskImage ? Did this work OK ?
DVD - type used
DVD - Brand used
Did You set down burn speed ?
Free space on Start-Up (Mac OS) hard disk - How much ?
You see there are so much more info needed to be able to pin the culprit.
Yours Bengt W

Burning ejects during "multiplexing and burning"

When I burn a dvd it goes the whole way and then with 10 minutes left when it is doing the "multiplexing and burning" part, it ejects before finished and I get a blank DVD. Tried a 1000 times. Has anyone else experienced this?
I've burned dvds before and had no problem.

Hi
My list on this
*Multiplexing Error*
PART One.
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else coverted to this .aff 48KHz)
*Chapters !*
A. *Using strange letters* in video project name eg +,/; etc. keep to a-z and 0-9 strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. *Location of Chapters*
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutly needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the uneditited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
*One user more writes*
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous trys, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no mulitplex error
As a final experiment, I moved "bad" chapter mark about 5-10 secs beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplexer Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Yours Bengt W

When I check my boot SSD drive using Disk Utility under Mavericks, I often get "Incorrect number of extended attributes" errors. But if I boot off an external drive and check the same SSD, no errors are reported. Is this a bug in Mavericks?

When I check my boot SSD drive using Disk Utility under Mavericks, I often get "Incorrect number of extended attributes" errors. But if I boot off an external drive and check the same SSD, no errors are reported.
This happens not just with the SSD in my Mac Mini, but with another SSD in my MacBook (both now running Mavericks). So far as I know, all of the kit I am using is in good order (despite the file corruption reports). So I am beginning to wonder if it could be due to a bug in Mavericks? Both SSD drives have been formatted to MacOS Extended (journaled) format. Should I have used a different format, I wonder?
Has anyone else encountered this issue?
Does anyone have a solution?
Or an explanation that might help my investigation of the issue?
Thanks guys,

I understand that the Corsair Force 3 is not one of the SSD drives that are supported on Apple Macs.
I did try downloading and using Trim Enabler, but the error message came up both when it was off and when it was on.
I understand that not everyone thinks Trim Enabler is a good program, though there is a new version out now, so I may give it another try.

IDVD stuck at multiplexing and Burn ("about one minute left" for hours)

Hello,
Well my problem is pretty simple, I am trying to create a simple DVD in iDVD with a *.mov file and a *.m4v file.
Everything goes well and pretty quick untill the last step (multiplexing and burning). One one line of the sceen it says "done" one line below that it says "about one minute left" and it stays there, the burn never finishes.
It counts down very good for the last 5 minutes left, and than it stops at "about one minute left".
Does anyone have an idea what can solve this ?
Thnx.

May be You find help in my collection on Multiplex Error
*Multiplexing Error*
*PART One.*
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else coverted to this .aff 48KHz)
Using strange letters in video project name eg +,/; etc. keep to a-z and 0-9
strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
*PART Two.*
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
*PART Three.*
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in:". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutly needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From: Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the uneditited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
Yours Bengt W

I've recently formatted my 10.7.4 mountain lion MacBook from 2007. The hard drive is wiped and I think it deleted to OS too. How do I put the OS back on it?

I've recently formatted my 10.7.4 mountain lion MacBook from 2007. The hard drive is wiped and I think it deleted to OS too. How do I put the OS back on it?

Wiping the drive does indeed delete the OS. Try this -
Boot to the Lion (10.7.4 is Lion not Mountain Lion) recovery partition by restarting the computer and holding down the command and R keys during startup.
If this works, reinstall from here. You must be connected to the Internet to do this.
If this does not work, possibly because you reformatted the recovery partition as well, you will need to reinstall from your original disks (assuming it came with 10.6 or earlier.) Boot to the disk by holding down the C key during startup and run the installer.
Best of luck.

I have bought a docking station and my iphone works fine but my ipod mini seems to fit on the connection but only works intermittently. Is it a different connection or is there a problem with the ipod?

I have bought a docking station and my iphone works fine but my ipod mini seems to fit on the connection but only works intermittently. Is it a different connection or is there a problem with the ipod?

I think that is happening is that the microphone is on during this recording. If you play the music through the iPhone speakers, it will record this sound, albeit at very poor quality. If you say anything (or laugh uproariously as I did while watching the app in action, then that, too, get recorded.
I am still looking for the solution we all want, which is to save the audio in reasonable quality.
Anyone out there with some ideas?
Cheers,
Rob

I inserted a cd that a friend of mine made me, it says there is nothing on the CD but now I can't figure out how to eject it

I inserted a CD that a friend made me, it says there is nothing on the CD but now I can't figure out how to eject it.....any help would be very appreciated.

Restart while holding the trackpad or mouse button down.
If that does not work, find Terminal in your Utilities folder and launch it.
At the prompt type
drutil eject
and press Return.

I have a MacBook using Snow Leopard 10.6.8 and iTunes 11.0.1. When I tether my new iPod Nano, the icon shows on my desktop, but the device does not show up on iTunes.

I have a MacBook with Snow Leopard 10.6.8 and iTunes 11.0.1. When I tether my new iPod Nano, the icon shows up on my desktop, but does not show up under devices in iTunes. The Nano says it is connected and synching, but I cannot download music if it doesn't show up under devices.

Hi,
Have you managed to solve this problem? if yes, please highlight how you solved it...i'm facing same problem with my new Iphone 5S but udner Windows, thanks.

HT1212 My daughter's iPod touch is stuck on a blank screen with the loading circle just going around and around. I tried to restore it, but it says I have to enter the passcode. I have the passcode, but as I said, there's nothing on the screen. How do I f

My daughter's iPod Touch is stuck on a blank screen with that loading circle thing just going around and around. She said she was trying to duplicate an app or something, and all the the apps started shaking like when you delete them. I turned the iPod off, but it never turned back on completely. I tried to restore it, but it's saying that I have to enter the passcode. But, as I said, there's nothing on the sceen excect the circle thing. Please help!!!!!

Start at # 3
1- iOS: Not responding or does not turn on
2 Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
3 If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
4 Try on another computer
5 If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Idvd ejects the disk during the "multiplexing and burning" / "writing lead-in" portion. When I check, there's nothing on the disk

Similar Messages

Maybe you are looking for