IE11 slow to load after installing EMET 5.1

After installing EMET 5.1 IE11 is taking 5-20 seconds to load. Basically the page stays blank for several seconds and the behavior varies depending on the hardware in use. Older machines take longer to load. If we remove the msthml.dll from EAF+ performance
almost back to normal?

Thanks Razmee
I did reset network settings but problem is still there.
iPhone does not remember the password.
I did a network reset and also a hard reboot holding upper and lower buttons.
So I have to reset the modem/router every time i want to connect the iPhone to WIFI
Never had a problem until installing iOS 5.1

Similar Messages

IMovie slow to load after installing SSD

Hi everyone, I have just installed an SSD in the spare optical drive bay of my Mac Pro and added RAM.
(Specs below.) I did a clean install of SL.
Before I did this I was booting from the 320GB drive that came with the computer and I have all my photos and video on a 2 drive RAID 0.
Before iMovie would launch in 11 seconds for the first launch and 6 seconds thereafter. That included loading projects and events.
Now it takes about 1 second to launch but 40 seconds to load the projects and events every time.
I have ditched pref files and retried but no good.
Any suggestions?

Yes, but the test is based on a 128k file, written many many times. That's fine with that, but video files imported into iMovie's cache area are not 128k large; they are much much larger especially when you're working with HD footage! You can also do another test and that is to completely wipe out your SSD drive and start over. After install, run iMovie 11 again and see. If it loads fast with the events, then you know that's the best that drive can do under your typical usage. However, if the drive still behaves exactly the same before and after a clean install, then something is wrong with the drive.
I don't believe there's any issues with your optical bay since it supports a SATA connection. You can check under system profile to see what link mode it is in now. For your Sandforce SSD, ideally it should be negotiating at 3Gbps rather than 1.5.
Personally, I have the same drives RAIDed in RAID 0 on my PC and while it is fast, it does slow down when I did too many big video writes despite what they claim as being trouble TRIM free. But with the slight slowdown, it is still much better and faster than a physical RAID 0 hard drive.

PE 9 will not load after installing Elements 10

Installed Elements 10 on Vista 64-bit. Did not uninstall Elements 9. Now PE 9 will not load; get window Adobe Premiere Elements.exe - No Disk. There is no disk in the drive. Please insert a disk into drive\Harddisk2\DR2. Tried disk 2 of 3 from package, nothing happens.

Tried twice, PE9 still locked up both times - I think the intent is to have me try PE10, because that did work!!!
From: Steve Grisetti
Sent: Monday, January 02, 2012 7:09 PM
To: cptiger
Subject: PE 9 will not load after installing Elements 10
Re: PE 9 will not load after installing Elements 10
created by Steve Grisetti in Premiere Elements - View the full discussion

Any idea how to get Yahoo to load after installing Mountain Lion??? Some sites load, but Yahoo wont at all...

Any idea how to get Yahoo to load after installing Mountain Lion??

http://www.koingosw.com/support/wiki/index.php/General_FAQ#Uninstalling_and_Pref erence_File_Locations

My iMac is very slow to boot after installing Yosemite

Hi
My iMac is very slow after installing Yosemite. Can any one help? Here is my Etrecheck below
EtreCheck version: 2.1.5 (108)
Report generated 20 December 2014 9:38:19 pm AWST
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
iMac (21.5-inch, Mid 2011) (Verified)
iMac - model: iMac12,1
1 2.8 GHz Intel Core i7 CPU: 4-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
BANK 0/DIMM1
empty empty empty empty
BANK 1/DIMM1
empty empty empty empty
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
AMD Radeon HD 6770M - VRAM: 512 MB
iMac 1920 x 1080
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:5:38
Disk Information: ℹ️
WDC WD1001FALS-403AA0 disk0 : (1 TB)
EFI (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 999.35 GB (680.79 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
HL-DT-STDVDRW GA32N
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
HP Photosmart 5520 series
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Apple Internal Memory Card Reader
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Applications/Splashtop Streamer.app
[not loaded] com.splashtop.driver.SRXDisplayCard (1.6 - SDK 10.7) [Support]
[not loaded] com.splashtop.driver.SRXFrameBufferConnector (1.6 - SDK 10.7) [Support]
/Library/Application Support/Avast/components/fileshield/unsigned
[loaded] com.avast.AvastFileShield (2.1.0 - SDK 10.9) [Support]
/Library/Application Support/Avast/components/proxy/unsigned
[loaded] com.avast.PacketForwarder (2.0 - SDK 10.9) [Support]
/System/Library/Extensions
[loaded] com.Cycling74.driver.Soundflower (1.6.6 - SDK 10.6) [Support]
Launch Agents: ℹ️
[loaded] com.avast.userinit.plist [Support]
[not loaded] com.splashtop.streamer-for-root.plist [Support]
[running] com.splashtop.streamer-for-user.plist [Support]
[running] com.teamviewer.teamviewer.plist [Support]
[running] com.teamviewer.teamviewer_desktop.plist [Support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
[loaded] com.avast.init.plist [Support]
[loaded] com.avast.uninstall.plist [Support]
[loaded] com.avast.update.plist [Support]
[not loaded] com.macpaw.CleanMyMac2.Agent.plist [Support]
[loaded] com.microsoft.office.licensing.helper.plist [Support]
[running] com.splashtop.streamer-daemon.plist [Support]
[loaded] com.splashtop.streamer-srioframebuffer.plist [Support]
[loaded] com.teamviewer.Helper.plist [Support]
[running] com.teamviewer.teamviewer_service.plist [Support]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Support]
[invalid?] com.avast.home.userinit.plist [Support]
[not loaded] com.google.keystone.agent.plist [Support]
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist [Support]
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist [Support]
[running] com.spotify.webhelper.plist [Support]
User Login Items: ℹ️
AdobeResourceSynchronizer ApplicationHidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
Dropbox Application (/Applications/Dropbox.app)
VLCStreamer Application (/Applications/VLCStreamer.app)
Internet Plug-ins: ℹ️
Flip4Mac WMV Plugin: Version: 3.0.0.126   - SDK 10.8 [Support]
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
Default Browser: Version: 600 - SDK 10.10
AdobePDFViewerNPAPI: Version: 10.1.13 [Support]
AdobePDFViewer: Version: 10.1.13 [Support]
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 [Support]
Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Support]
JavaAppletPlugin: Version: 15.0.0 - SDK 10.10 Check version
Safari Extensions: ℹ️
wrc [Installed]
3rd Party Preference Panes: ℹ️
Flash Player [Support]
Flip4Mac WMV [Support]
Time Machine: ℹ️
Skip System Files: NO
Mobile backups: OFF
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 999.35 GB Disk used: 318.55 GB
Destinations:
Data [Network]
Total size: 3.00 TB
Total number of backups: 84
Oldest backup: 2013-09-21 09:42:27 +0000
Last backup: 2014-12-20 11:26:14 +0000
Size of backup disk: Excellent
Backup size 3.00 TB > (Disk size 999.35 GB X 3)
Top Processes by CPU: ℹ️
      3% com.apple.WebKit.WebContent
      1% WindowServer
      1% Safari
      1% TeamViewer_Service
      0% com.avast.daemon
Top Processes by Memory: ℹ️
219 MB com.apple.WebKit.WebContent
133 MB com.avast.daemon
90 MB ocspd
77 MB mds_stores
73 MB Dropbox
Virtual Memory Information: ℹ️
82 MB Free RAM
1.70 GB Active RAM
1.67 GB Inactive RAM
829 MB Wired RAM
2.20 GB Page-ins
111 KB Page-outs
Diagnostics Information: ℹ️
Dec 20, 2014, 09:35:40 PM /Library/Logs/DiagnosticReports/com.avast.daemon_2014-12-20-213540_[redacted].c pu_resource.diag [Details]
Dec 20, 2014, 09:33:21 PM Self test - passed
Dec 20, 2014, 09:11:53 PM /Users/[redacted]/Library/Logs/DiagnosticReports/Finder_2014-12-20-211153_[reda cted].crash

Uninstall Avast and CleanMyMac2.
Avast Un-install
You do not need to use cleaning programs. They can destroy your computer operation as they may already have done.
CleanMyMac - Uninstall
CleanMyMac2 Un-install
After un-installing, run this program to make sure you got all the pieces.
EasyFind – Spotlight Replacement
Activity Monitor - Mavericks also Yosemite
Activity Monitor in Mavericks has significant changes
Performance Guide
Why is my computer slow
Why your Mac runs slower than it should
Slow Mac After Mavericks
Things you can do to resolve slowdowns see post by Kappy

Safari slow to load after upgrading to 10.10.2

Ever since upgrading my brand new Mac to 10.10.2, Safari has been exceedingly slow to load -- sometimes refusing to load, altogether. Any help with this?

Please answer as many of the following questions as you can. You may already have answered some of them. In that case, there's no need to repeat the answers.
Back up all data before making any changes.
Have you restarted your router and your broadband device (if they're separate) since you first noticed the problem? If not, do that now and see whether there's any change.
If your browser is Safari, then from the Safari menu bar, select
Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data
and confirm. If the Downloads button (with the icon of a downward-pointing arrow) is showing in the toolbar, click it and then click Clear in the box that appears. The download history will be removed. Any change?
If you're running OS X 10.9 or later, select the Advanced tab in the Preferences window and uncheck the box marked
Stop plug-ins to save power
Any change?
Quit and relaunch the browser. Any change?
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Are any other web browsers installed, and are they the same? What about other Internet applications, such as iTunes and the App Store?
If other browsers and Internet applications are also affected, follow these instructions and test. Any change?
If Parental Controls is active for any user, please turn it off and test. Any change?
If only Safari is affected, launch the Activity Monitor application and enter "web" (without the quotes) in the search box. If a process named "Safari Web Content" is shown in red or is using more than about 5% of a CPU, select it and force it to quit by clicking the X or Quit Process button in the toolbar of the window. There may be more than one such process. Any improvement?
Follow the instructions in this support article. Any change?
Open the iCloud preference pane and uncheck the boxes marked Safari and Photos, if they're checked. Any change?
Are there any other devices on the same network that can browse the Web, and are they affected?
If you can test Safari on another network, is it the same there?
If you connect to your router with Wi-Fi and you can also connect with Ethernet, do that and turn off Wi-Fi. Any difference?

IPHOTO NO LONGER LOADS AFTER INSTALLING 10.4.10 on G4

After installing 10.4.10 on a G4 desktop, iPhoto no longer loads. When I try to rebuild library, the applications quits at the last instant. Any suggestions on how to fix or how to uninstall and get back to earlier system?

Hello young:
Hopefully you had a backup of your system prior to updating. Going "back" will probably not help as it it unlikely that OS X 10.4.10 caused the problem (it has been ouut for awhile, and no similar problems have been noted, as far as I know).
I suggest that you do several things:
Run repair disk from your software install DVD.
Run repair permissions from your internal HD.
If those do not help, download the combo OS X 10.4.10 and reinstall it.
Barry

MacBook Pro 13 " going slower in performance after Installing LION OSX

Hey Guys ,
I had noticed some problems in my MacBook Pro 13" which I bought in the MID of 2011 ( i5 processor ) , I had purchased and installed LION OSX and observed after installing that my Backlite ( Keyboard ) dont get on when I start up at the LOG IN , which used to work in SNOW LEOPARD .
Booting takes SO SO SO long as when comapared with the previous OS .
Heating Problem is also a must to mention .
If you guys know how to reduce these problems please help me out !
Thank You .

I'm curious if you ever found a solution for this issue. I recently purchased the SanDisk Extreme II 480GB, replacing my OWC Extreme Pro 240GB. The OWC never experienced the "slow to wake" issue whereas the SanDisk drive does, consistently. To make sure I'm having the same symptoms, this is what happens to me: Put the mac to sleep (either manually or letting it do it on its own, waiting for the led to pulse showing that it is asleep), then wake it up (press a key on the keyboard), the logon screen shows almost immediately but as soon as I try to type the pinwheel/beach ball shows up, I wait between 20 and 30 seconds and then I'm able to type and all is well.
I contataced SanDisk and their support was horrible. They simply told me "contact MAC for this issue" (no joke, not "contact Apple" but "contact MAC", in all caps). I explained that it works fine with the OWC drive just not the SanDisk. They replied with another article showing that all macs have trouble waking from sleep (not true). I replied again indicating that I've never had this issue with any of my 3rd party drives, only this SanDisk. Then the replied simply stating that all mac's have issues with 3rd party hard drives when waking from sleep. At this point I threw a fit and yelled at my screen, even though it wasn't my screens fault.
In any case, their support has not been willing to do any actual troubleshooting. I'd love to return it and I might have to - but as you stated, it's annoying to have this issue but the performance is fine the rest of the time.
Thanks for any input you have.
Bryan

Slow Booting time after installing MacBook Pro EFI Firmware Update 2.0 on 13 Inches Mac 2010 model

I'm experiencing a slow boot time after my computer installed a MacBook Pro EFI Firmware Update 2.0 itself on 13 Inches 2010 model, how to downgrade or fix it?
My computer is starting 2 times slower then it should be, why Apple done this to me?
Please help who really know somthing about Macs.

I have the same problem, especially when I open my laptop from sleep. It takes at least 2 minutes for the computer Internet connection to work.
Never had that problem prior to the last firmware update 2.7.
Is there a way to revert back to 2.6?

Loop when loading after installing leopard

After installing leopard, my computer is not loading properly.
I can log in, the dock opens but then a window pops up saying "None of your preferred networks are available", displaying other networks; however the spinning coloured wheel appears and I am unable to advance from here.
The dock however works OK, and I can open dashboard (but cant use widgets). Finder is also not yet open, but if I click on it on the dock its light turns on (it "opens") and the top bar opens up, showing standard menu options and the spotlight icon. However after this it also freezes (spinning wheel again).
I suspect there is a problem (loop?) loading AirPort, which is blocking other apps and Finder. The computer gets stuck. I already tried "fix permissions" and "fix disc" using utilities, and I tried logging in safe mode, but it freezes immediately after the dock shows, not even showing the top bar, even before the point it freezes in normal mode.
Does anyone know how I can get around this?
(I can also access my HD using networking if I am connected by cable).

I am having the exact same issue on my G5. It's been sitting there hung up on "none of your preferred networks are available" for 30 minutes now. I repaired permissions before installing, and I'm able to boot from the CD and re-check them - everything's OK. Anyone have any suggestions?

Can't get lightroom cc to load after install

can't get lightroom cc to load after install

Have you tried logging out of your CC desktop app, then logging back in again? Quit/Restart won't work, but logging out and back in should. See here: https://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

All application slow to molasse after Installing Security-Update 2010_007

After installing security update, ALL applications, all commands in X11 had response times ALL key strokes of the order of seconds to minutes with >93% of system CPU idle. Console displays the message below ever 60-70 seconds.
11/11/10 4:25:36 PM updatedyld_sharedcache[12] for arch=i386 failed: read failure copying dylib errno=5 for /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libLAPACK.dylib while copying /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libLAPACK.dylib to shared cache
The solution is a modification of this link
http://www.macosxhints.ch/forums/showthread.php?t=15517
Basically, the offending file /System/.../LibLAPACK.dylib is moved from the system directory to a current directory, e.g.,
sudo mv /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libLAPACK.dylib .
and then back to the original directory, e.g.,
sudo mv libLAPACK.dylib /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libLAPACK.dylib
Problem solved without reboot as system immediately returns to normal. Why would a security update from Apple cause this?

Andreas, do you have this info in english? I'm having a similar problem, and I want to see if I can solve it; or could you tell me what you did to solve it?
Here's the message I'm getting every minute from the console:
updatedyld_sharedcache[1461] for arch=i386 failed: read failure copying dylib errno=5 for /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Frameworks/ CoreGraphics.framework/Versions/A/CoreGraphics while copying /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Frameworks/ CoreGraphics.framework/Versions/A/CoreGraphics to shared cache

Slow wake up after installing lion (Macbook Pro 2010)

Hi there,
After installing Lion, my Macbook Pro 15" takes a lot longer to wake up from sleep than before (taking 10 or more seconds, instead of 2 seconds in Snow Leopard).
Am I the only one seeing this? I did a normal install (upgrade from SL) from the Mac App store. RAM is 8 GB.
Thanks!
FR.

I seem to have fixed this issue. I ran Disk Utility and it showed error in the file structure. I rebooted into to Lion Recovery partition and ran Disk Utility, did a repair, and now (for the time being) it wakes as expected without all the whiring fans and falling back off to sleepland.
One gotcha with the recovery partition boot is that it doesn't recognise Magic Mouse, and I had to dig out my USB mouse.
Hope this info is of some help.

Apps don't load after installing iOS4

Hi all,
I installed OS4 and had to install it as I couldn't update any apps without upgrading the OS, well that was the error message from the Apps Store, of which I was tired and eventually upgraded my phone. Now I am having a problem where none of the apps load, the initial load screen comes and the app then quits. All the apps loaded before the upgrade as well as the new apps after the apps behave this way. Any help will be greatly appreciated.
Thanks.

If you still have the problem after restoring to factory settings/new iPod that indicates a hardware problem.

CS4 After Effects no longer loading after installing Office 08

During the christmas break I installed Office 08 and its seamed to have mucked something up in CS4 After effects because it won't load anymore, the program starts loading the libraries and all that stuff at the splash screen and crashes when loading User interface
After effects worked fine before I installed office 08. Does anyone know what has happened and how to fix it? The strange thing is, it works on a couple of macs but the majority of the lab is having this problem.
I have tried heaps of things:
- Totally uninstalled office 08 and its preferences
- Uninstall CS4 and manually remove all the preference files
- Locate the fonts folders and comparing the fonts with that of a working mac
- Creating a new login account
- Updated to After effects 9.0.2
After spending hours and hours and hours doing this, I have had no luck solving the issue. Help will be greatly appreciated... I will backup all the data and re-install Leopard next week if no-one knows how to fix this.
Here is part of the error message that i have reported to adobe and haven't had a reply
Process:         After Effects [139]
Path:            /Applications/Adobe After Effects CS4/Adobe After Effects CS4.app/Contents/MacOS/After Effects
Identifier:      com.adobe.AfterEffects
Version:         9.0 (9.0)
Code Type:       X86 (Native)
Parent Process: launchd [93]
Interval Since Last Report:          204 sec
Crashes Since Last Report:           1
Per-App Interval Since Last Report: 148 sec
Per-App Crashes Since Last Report:   1
Date/Time:       2010-03-17 11:13:10.239 +1100
OS Version:      Mac OS X 10.5.8 (9L31a)
Report Version: 6
Anonymous UUID: 93AB0F34-3CF9-41AE-A9E5-21738DB3269F
Exception Type: EXC_BAD_ACCESS (SIGABRT)
Exception Codes: KERN_PROTECTION_FAILURE at 0x0000000000000008
Crashed Thread: 0
Thread 0 Crashed:
0   libSystem.B.dylib             0x91ccce42 __kill + 10
1   libSystem.B.dylib             0x91d3f23a raise + 26
2   libSystem.B.dylib             0x91d4b679 abort + 73
3   U.dylib                       0x029a529f U_LoadFrameworkBundle + 671
4   libSystem.B.dylib             0x91ccb2bb _sigtramp + 43
5   com.macromedia.FLVExporter    0x2ba2ded5 FLVCore::Initialize(__CFBundle*) + 657
6   com.macromedia.FLVExporter    0x2ba45c32 FLVExporter::FLVExporter(ComponentInstanceRecord*) + 130
7   com.macromedia.FLVExporter    0x2ba46005 FLVExportOpen + 37
8   com.macromedia.FLVExporter    0x2ba468ca FLVExportComponentDispatch + 130
9   ...ple.CoreServices.CarbonCore 0x957b2935 CallComponentDispatch + 29
10 ...ple.CoreServices.CarbonCore 0x957b2915 CallComponentOpen + 43
11 ...ple.CoreServices.CarbonCore 0x957b0fb1 OpenAComponent + 449
12 ...ple.CoreServices.CarbonCore 0x957b0dea OpenComponent + 24
13 ...dobe.AfterEffects.framework 0x00fe574c FEE_GetMotionTrackCmdAttrs(long, bool, bool, long, char*, bool*) + 512746
14 ...dobe.AfterEffects.framework 0x00fe58fb FEE_GetMotionTrackCmdAttrs(long, bool, bool, long, char*, bool*) + 513177
15 ...dobe.AfterEffects.framework 0x00fe7d5c FEE_GetMotionTrackCmdAttrs(long, bool, bool, long, char*, bool*) + 522490
16 ...dobe.AfterEffects.framework 0x00ce44db CEggApp::IEggApp(bool, bool, boost::function0<void, std::allocator<boost::function_base> >) + 17347
17 ...dobe.AfterEffects.framework 0x00ce7e4d CEggApp::CEggApp(bool, bool, boost::function0<void, std::allocator<boost::function_base> >, long) + 919
18 ...dobe.AfterEffects.framework 0x00ceb825 egg::dvainit::DVAConsoleEnabled() + 1809
19 ...dobe.AfterEffects.framework 0x00cebc37 EggMain(bool, bool, bool, bool, bool, char*, bool, long) + 97
20 com.adobe.AfterEffects        0x00005bc6 main + 1574
21 com.adobe.AfterEffects        0x00004f62 _start + 216
22 com.adobe.AfterEffects        0x00004e89 start + 41
Thread 1:
0   libSystem.B.dylib             0x91c8f9c6 kevent + 10
1   libSystem.B.dylib             0x91c90155 _pthread_start + 321
2   libSystem.B.dylib             0x91c90012 thread_start + 34
Thread 2:
0   libSystem.B.dylib             0x91c5f2ce semaphore_wait_signal_trap + 10
1   libSystem.B.dylib             0x91c912c6 _pthread_cond_wait + 1267
2   libSystem.B.dylib             0x91cd6539 pthread_cond_wait + 48
3   com.adobe.amt.services        0x1f44e294 AMTConditionLock::LockWhenCondition(int) + 52
4   com.adobe.amt.services        0x1f448bfa _AMTThreadedPCDService::PCDThreadWorker(_AMTThreadedPCDService*) + 130
5   com.adobe.amt.services        0x1f44e379 AMTThread::Worker(void*) + 29
6   libSystem.B.dylib             0x91c90155 _pthread_start + 321
7   libSystem.B.dylib             0x91c90012 thread_start + 34

The failure appears to be in the FLV QuickTime component, which is an FLV exporter for QuickTime that Adobe Flash (or older Macromedia releases) installs into your [root]/Library/QuickTime folder. After Effects loads any such component that QuickTime makes available (they appear under the File > Export menu).
First, try deleting the com.macromedia.FLVExporter in your [username]/Library/Preferences folder, if present. Failing that, pull out the FLV QuickTime component I described above.
It is also theoretically possible that the failure is in the next component in the QuickTime components folder, not the FLV component. You might could just pull out the entire contents of that folder and see what happens.
-=TimK
-=After Effects QE

IE11 slow to load after installing EMET 5.1

Similar Messages

Maybe you are looking for