IEEE 802.1x Port based Authentication with Restricted VLAN

Hi all,
I have the following configuration:
aaa new-model
aaa authentication dot1x default group radius
aaa authorization exec default local
dot1x system-auth-control
radius-server host 10.10.10.10 key cisco
interface FastEthernet0/1
switchport mode access
authentication event fail retry 1 action authorize vlan 2
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
But it takes quite a while for the user who is not authorized to be switch to vlan 2.
I would like to know what is best practice when using this kind of configuration and if it is possible to optimize on how long it takes to switch the unauthorized user to the restricted VLAN?
Regards,
Laurent

Laurent,
Based on your configuration it looks as if it will take one retry attempt before the client is placed in vlan2. Try to remove the 'retry 1' from command and see if that speeds up the time. Also take the output of the 'show authentication sessions interface '. Please post the output of the 'debug radius authentication' as that will help to see how long it is taking the radius server to respond.
thanks,
Tarik Admani

Similar Messages

IEEE 802.1x port-based authetication

I want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone.
I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.

Hi Claudia,
do you mean that the EAP-TLS authentication fails only on some 2960 switches and it works on other 2960s?
What is the IOS version you're using there?
What is the RADIUS server in use?
What is the exact error message you see on the RADIUS side?
Usually, the reason for the EAP-TLS handshake failure is to be troubleshoot on the supplicant and AAA server, however, there may be something on the switch depending on the certificate size and MTU settings on the switch(es).
What is the server cert size and the MTU configured on the switches?
With the info you provided it's difficult to say what's the reason of this failure.
I would suggest to start looking into the above mentioned topics, else you would need to proceed with deeper debugging and sniffer traces, which may be better/easier to handle through a TAC case.
I hope this helps.
Regards,
Federico
If this answers your question please mark the question as "answered" and rate it, so other users can easily find it.

Help with 4506 802.1x Port Based Authentication (Wired)

Hi all,
I'm trying to configure wired 802.1x security on a Catalyst 4506 IOS 12.1.19(EW), using Microsoft IAS (Microsoft's RADIUS), and Windows 2000 SP4 clients.
I've followed the procedures in the 4506 Software configuration guide and they seem to be straight forward.
I then turn 802.1x Debugging on the switch to monitor the 802.1x traffic, but there is none. If I bring the configured interface down and then back up, I do get some status change, but it seems like the switch is not sending or receiving EAPOL frames.
I then execute the dot1x "initialize" and also tried the "re-authenticate" commands, but I get an error saying that FastEthernet 2/2 is not a valid dot1x interface. The line card model number is WS-X4148-RJ21. Is the card not 802.1x compatible?
The switch does not throw any errors when I configure FastEthernet 2/2 as a 802.1x port by executing
dot1x port-control auto
i've also configured the interface to be a plain L2 access port by executing
switchport mode access
any help will be appreciated!

I am currently trying to get 802.1x port authentication working on a Cat3550 against Win2003 IAS but the IAS log shows a invalid message-authenticator error. The 3550 just shows failed. When I authenticate against Cisco ACS (by simply changing the radius-server) it works perfectly.
However, I am successfully using IAS to authenticate WPA users on AP1210s so RADIUS appears to be OK working OK.
Are there special attributes that need to be configured on the switch or IAS?

802.1X Port Based Authentication - IP Phone- MDA - Port Security Violation

I have configured 802.1X authentication on selected ports of a Cisco Catalyst 2960S with Micorsoft NPS Radius authentication on a test LAN. I have tested the authentication with a windows XP laptop, a windows 7 laptop with 802.1X, eap-tls authentication and a Mitel 5330 IP Phone using EAP-MD5 aithentication. All the above devices work with with the MS NPS server. However in MDA mode when the 802.1x compliant windows 7 laptop is connected to the already authenticated Mitel IP Phone, the port experiences a security violation and the goes into error sdisable mode.
Feb 4 19:16:16.571: %AUTHMGR-5-START: Starting 'dot1x' for client (24b6.fdfa.749b) on Interface Gi1/0/1 AuditSessionID AC10A0FE0000002F000D3CED
Feb 4 19:16:16.645: %DOT1X-5-SUCCESS: Authentication successful for client (24b6.fdfa.749b) on Interface Gi1/0/1 AuditSessionID AC10A0FE0000002F000D3CED
Feb 4 19:16:16.645: %PM-4-ERR_DISABLE: security-violation error detected on Gi1/0/1, putting Gi1/0/1 in err-disable state
Feb 4 19:16:17.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Feb 4 19:16:18.658: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
If the port config is changed to "authentication host-mode multi-auth", and the laptop is connected to the phone the port does not experience the security violation but the 802.1x authentication for the laptop fails.
The ports GI1/0./1 & Gi1/02 are configured thus:
interface GigabitEthernet1/0/1
switchport mode access
switchport voice vlan 20
authentication event fail action authorize vlan 4
authentication event no-response action authorize vlan 4
authentication event server alive action reinitialize
authentication host-mode multi-domain
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
mab
mls qos trust cos
dot1x pae authenticator
spanning-tree portfast
sh ver
Switch Ports Model SW Version SW Image
* 1 52 WS-C2960S-48FPS-L 15.2(1)E1 C2960S-UNIVERSALK9-M
Full config attached. Assistance will be grately appreciated.
Donfrico

I am currently trying to get 802.1x port authentication working on a Cat3550 against Win2003 IAS but the IAS log shows a invalid message-authenticator error. The 3550 just shows failed. When I authenticate against Cisco ACS (by simply changing the radius-server) it works perfectly.
However, I am successfully using IAS to authenticate WPA users on AP1210s so RADIUS appears to be OK working OK.
Are there special attributes that need to be configured on the switch or IAS?

802.1X Port Based Authentication Security Violation

I have configured 802.1X authentication on selected ports of a Cisco Catalyst 2960S with Micorsoft NPS Radius authentication on a test LAN. I have tested the authentication with a windows XP laptop, a windows 7 laptop with 802.1X, eap-tls authentication and a Mitel 5330 IP Phone using EAP-MD5 aithentication. All the above devices work with with the MS NPS server. However in MDA mode when the 802.1x compliant windows 7 laptop is connected to the already authenticated Mitel IP Phone, the port experiences a security violation and the goes into error sdisable mode.
Feb 4 19:16:16.571: %AUTHMGR-5-START: Starting 'dot1x' for client (24b6.fdfa.749b) on Interface Gi1/0/1 AuditSessionID AC10A0FE0000002F000D3CED
Feb 4 19:16:16.645: %DOT1X-5-SUCCESS: Authentication successful for client (24b6.fdfa.749b) on Interface Gi1/0/1 AuditSessionID AC10A0FE0000002F000D3CED
Feb 4 19:16:16.645: %PM-4-ERR_DISABLE: security-violation error detected on Gi1/0/1, putting Gi1/0/1 in err-disable state
Feb 4 19:16:17.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Feb 4 19:16:18.658: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
If the port config is changed to "authentication host-mode multi-auth", and the laptop is connected to the phone the port does not experience the security violation but the 802.1x authentication for the laptop fails.
The ports GI1/0./1 & Gi1/02 are configured thus:
interface GigabitEthernet1/0/1
switchport mode access
switchport voice vlan 20
authentication event fail action authorize vlan 4
authentication event no-response action authorize vlan 4
authentication event server alive action reinitialize
authentication host-mode multi-domain
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
mab
mls qos trust cos
dot1x pae authenticator
spanning-tree portfast
sh ver
Switch Ports Model SW Version SW Image
* 1 52 WS-C2960S-48FPS-L 15.2(1)E1 C2960S-UNIVERSALK9-M
Full config attached. Assistance will be grately appreciated.
Donfrico

I believe , you need to configure re-authentication on this switch port:
! Enable re-authentication
authentication periodic
! Enable re-authentication via RADIUS Session-Timeout
authentication timer reauthenticate server

802.1x mac based authentication

We have Cisco ACS 3.3 is there a way to do authentication based on mac address, instead of username and password? We are looking to stop things such as user purchased access points and what not. Any info would be great.

Yes you are right, I misunderstood you. I was under the impression that you were talking about doing MAC based authentication on your AP's, not the switches. That is why I made mention to port security.
The 2 options would be standard port security or 802.1x port security if you switches support this.
In order to use the 802.1X port security, your switch would need to support it and the clients connecting to the switch would require a supplicant (EAP-TLS, EAP-TTLS, etc) in order for them to work, not by MAC address alone.
You can configure standard port security on the switch which will accomplish your intentions and not even need to use the ACS server.
standard port base security by MAC:
http://www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_guide_chapter09186a008007d3ce.html
802.1x port based security:
http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a00801a6c72.html

Certificate based authentication with sender SOAP adapter. Please help!

Hi Experts,
I have a scenario where first a .Net application makes a webservice call to XI via SOAP Adapter. Then the input from the .Net application is sent to the R/3 system via RFC adapter.
.Net --->SOAP -
>XI -
>RFC -
R/3 System
Now as per client requirement I have to implement certificate based authentication in the sender side for the webservice call. In this case the .Net application is the "client" and XI is the "server". In other words the client has to be authenticated by XI server. In order to accomplish this I have setup the security level in the SOAP sender channel as "HTTPS with client authentication". Additionally I have assigned a .Net userid in the sender agreement under "Assigned users" tab.
I have also installed the SSL certificate in the client side. Then generated the public key and loaded it into the XI server's keystore.
When I test the webservice via SOAPUI tool I am always getting the "401 Unauthorized" error. However if I give the userid/password for XI login in the properties option in the SOAPUI tool then it works fine. But my understanding is that in certificate based authentication, the authentication should happen based on the certificate and hence there is no need for the user to enter userid/password. Is my understanding correct? How to exactly test certificate based authentication?
Am I missing any steps for certificate based authentication?
Please help
Thanks
Gopal
Edited by: gopalkrishna baliga on Feb 5, 2008 10:51 AM

Hi!
Although soapUI is a very goot SOAP testing tool, you can't test certificate based authentication with it. There is no way (since I know) how to import certificat into soapUI.
So, try to find other tool, which can use certificates or tey it directly with the sender system.
Peter

Port-Based Authentication on 877

Hi
I have applied following commands to enable Port-Based Authentication but when I run command sh mac address-table it shows static mac on this port ( xx 0000.xxxx.xxxx STATIC Gi1/0/3) .
authentication control-direction in
authentication event fail retry 1 action authorize vlan xx
authentication event no-response action authorize vlan xx
authentication host-mode multi-domain
authentication order dot1x mab
authentication port-control auto
authentication violation protect
mab
dot1x pae authenticator
dot1x timeout quiet-period 10
dot1x timeout tx-period 10
dot1x timeout supp-timeout 10
As I remove command authentication port-control auto then sh mac address-table command shows me DYNAMIC MAC.
Anyone can please let explain me why it is happing
Regards,

Any input?

802.1x Machine Based Authentication - Password expired

Hi,
I would like to ask 1 question about machine based authentication on 802.1x.
1.We are deploying 802.1x on wired user.
2.Some user are using machine based authentication in order to authenticate their port.
3.However, after the user password expired, the user need to change their password and then the machine are unable to authenticate. The error i got is "External DB user invalid or bad password". Then switch assign the user to Guest Vlan
4.But, once i plug out the cable and plug in back the UTP cable after the user login, the switch will assigned the user to proper VLAN.
5.User wont be able to access their share drive n etc since the guest vlan only have access to the internet.
5.Anyone have any idea what is happening? It seems that the machine is sending the old password during authentication process to the ACS.
Anybody can shed a light to me. Thanks.

This should certainly work with that rev. On your passed (or failed) auth log, you should see the username of the session authenticating. If you see the FQDN of the machine, this is a machine auth. Also, machine-auth typically executes before the GINA is displayed to the user. It sounds like machine-auth is failing and we need to determine why. Has this machine been away from the domain for long?
This also might help:
http://supportwiki.cisco.com/ViewWiki/index.php/802.1x_authentication_with_Cisco_Secure_Access_Control_Server_fails_to_work_for_Microsoft_Windows_XP_PC

802.1x PEAP Machine Authentication with MS Active Directory

802.1x PEAP Machine and User Authentication with MS Active Directory:
I have a simple pilot-text environment, with
- Microsoft XP Client,
- Cisco 2960 Switch,
- ACS Solution Engine (4.1.4)
- MS Active Directory on Win 2003 Server
The Remote Agent (at 4.1.4) is on the same server as the MS AD.
User Authentication works correctly, but Machine Authentication fails.
Failed machine authenticaton is reported in the "Failed Attempts" log of the ACS SE.
The Remote Agent shows an error:
See Attachment.
Without Port-Security the XP workstation is able to log on to the domain.
Many thanks for any indication.
Regards,
Stephan Imhof

Is host/TestClientMan.Test.local the name of the machine? What does the AAA tell for you the reason it fails?

Retrieving results for comparison in form based authentication with entitie

Hi,Im developing an application using EJB3.0 and at the moment im working on a module involving user authentication.I work with the sun java system appserver 9.1 and netbeans 5.5.2 using the default toplink as the persistent provider.I have problems performing user based authentication.where am at is at shown below.I used a SLSB facade design pattern and created an entity from an existing database I built solely for the application (table name user_table). This is the code I have currently:
Entity
* UserTable.java
* Created on 31 March 2008, 16:06
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import java.io.Serializable;
import javax.persistence.Column;
import javax.persistence.Entity;
import javax.persistence.Id;
import javax.persistence.Table;
* Entity class UserTable
* @author Ayo
@Entity
@Table(name = "user_table")
public class UserTable implements Serializable {
@Id
@Column(name = "user_id", nullable = false)
private Integer userId;
@Column(name = "username")
private String username;
@Column(name = "password")
private String password;
@Column(name = "user_type")
private String userType;
@Column(name = "access_level")
private String accessLevel;
@Column(name = "staff_id")
private Integer staffId;
@Column(name = "staff_type", nullable = false)
private String staffType;
@Column(name = "time_created")
private String timeCreated;
@Column(name = "time_modified")
private String timeModified;
@Column(name = "time_logged_in")
private String timeLoggedIn;
@Column(name = "time_logged_out")
private String timeLoggedOut;
@Column(name = "created_by")
private String createdBy;
/** Creates a new instance of UserTable */
public UserTable() {
* Creates a new instance of UserTable with the specified values.
* @param userId the userId of the UserTable
public UserTable(Integer userId) {
this.userId = userId;
* Creates a new instance of UserTable with the specified values.
* @param userId the userId of the UserTable
* @param staffType the staffType of the UserTable
public UserTable(Integer userId, String staffType) {
this.userId = userId;
this.staffType = staffType;
* Gets the userId of this UserTable.
* @return the userId
public Integer getUserId() {
return this.userId;
* Sets the userId of this UserTable to the specified value.
* @param userId the new userId
public void setUserId(Integer userId) {
this.userId = userId;
* Gets the username of this UserTable.
* @return the username
public String getUsername() {
return this.username;
* Sets the username of this UserTable to the specified value.
* @param username the new username
public void setUsername(String username) {
this.username=username;
* Gets the password of this UserTable.
* @return the password
public String getPassword() {
return this.password;
* Sets the password of this UserTable to the specified value.
* @param password the new password
public void setPassword(String password) {
this.password=password;
* Gets the userType of this UserTable.
* @return the userType
public String getUserType() {
return this.userType;
* Sets the userType of this UserTable to the specified value.
* @param userType the new userType
public void setUserType(String userType) {
this.userType = userType;
* Gets the accessLevel of this UserTable.
* @return the accessLevel
public String getAccessLevel() {
return this.accessLevel;
* Sets the accessLevel of this UserTable to the specified value.
* @param accessLevel the new accessLevel
public void setAccessLevel(String accessLevel) {
this.accessLevel = accessLevel;
* Gets the staffId of this UserTable.
* @return the staffId
public Integer getStaffId() {
return this.staffId;
* Sets the staffId of this UserTable to the specified value.
* @param staffId the new staffId
public void setStaffId(Integer staffId) {
this.staffId = staffId;
* Gets the staffType of this UserTable.
* @return the staffType
public String getStaffType() {
return this.staffType;
* Sets the staffType of this UserTable to the specified value.
* @param staffType the new staffType
public void setStaffType(String staffType) {
this.staffType = staffType;
* Gets the timeCreated of this UserTable.
* @return the timeCreated
public String getTimeCreated() {
return this.timeCreated;
* Sets the timeCreated of this UserTable to the specified value.
* @param timeCreated the new timeCreated
public void setTimeCreated(String timeCreated) {
this.timeCreated = timeCreated;
* Gets the timeModified of this UserTable.
* @return the timeModified
public String getTimeModified() {
return this.timeModified;
* Sets the timeModified of this UserTable to the specified value.
* @param timeModified the new timeModified
public void setTimeModified(String timeModified) {
this.timeModified = timeModified;
* Gets the timeLoggedIn of this UserTable.
* @return the timeLoggedIn
public String getTimeLoggedIn() {
return this.timeLoggedIn;
* Sets the timeLoggedIn of this UserTable to the specified value.
* @param timeLoggedIn the new timeLoggedIn
public void setTimeLoggedIn(String timeLoggedIn) {
this.timeLoggedIn = timeLoggedIn;
* Gets the timeLoggedOut of this UserTable.
* @return the timeLoggedOut
public String getTimeLoggedOut() {
return this.timeLoggedOut;
* Sets the timeLoggedOut of this UserTable to the specified value.
* @param timeLoggedOut the new timeLoggedOut
public void setTimeLoggedOut(String timeLoggedOut) {
this.timeLoggedOut = timeLoggedOut;
* Gets the createdBy of this UserTable.
* @return the createdBy
public String getCreatedBy() {
return this.createdBy;
* Sets the createdBy of this UserTable to the specified value.
* @param createdBy the new createdBy
public void setCreatedBy(String createdBy) {
this.createdBy = createdBy;
* Returns a hash code value for the object. This implementation computes
* a hash code value based on the id fields in this object.
* @return a hash code value for this object.
@Override
public int hashCode() {
int hash = 0;
hash += (this.userId != null ? this.userId.hashCode() : 0);
return hash;
* Determines whether another object is equal to this UserTable. The result is
* <code>true</code> if and only if the argument is not null and is a UserTable object that
* has the same id field values as this object.
* @param object the reference object with which to compare
* @return <code>true</code> if this object is the same as the argument;
* <code>false</code> otherwise.
@Override
public boolean equals(Object object) {
// TODO: Warning - this method won't work in the case the id fields are not set
if (!(object instanceof UserTable)) {
return false;
UserTable other = (UserTable)object;
if (this.userId != other.userId && (this.userId == null || !this.userId.equals(other.userId))) return false;
return true;
* Returns a string representation of the object. This implementation constructs
* that representation based on the id fields.
* @return a string representation of the object.
@Override
public String toString() {
return "Entities.UserTable[userId=" + userId + "]";
SLSB
* UserTableFacade.java
* Created on 31 March 2008, 16:07
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import java.util.*;
import javax.ejb.Stateless;
import javax.persistence.EntityManager;
import javax.persistence.PersistenceContext;
* @author Ayo
@Stateless
public class UserTableFacade implements UserTableFacadeLocal {
@PersistenceContext
private EntityManager em;
/** Creates a new instance of UserTableFacade */
public UserTableFacade() {
public void create(UserTable userTable) {
em.persist(userTable);
public void edit(UserTable userTable) {
em.merge(userTable);
public void destroy(UserTable userTable) {
em.merge(userTable);
em.remove(userTable);
public List findAll() {
return em.createQuery("select Object(o)from UserTable as o").getResultList();
local interface
* UserTableFacadeLocal.java
* Created on 31 March 2008, 16:07
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import java.util.*;
import javax.ejb.Local;
* @author Ayo
@Local
public interface UserTableFacadeLocal {
void create(UserTable userTable);
void edit(UserTable userTable);
void destroy(UserTable userTable);
List findAll();
controller servlet
* userCheck.java
* Created on 15 March 2008, 22:41
package servlets;
import Entities.UserTable;
import Entities.UserTableFacadeLocal;
import Entities.userValidationBean;
import Entities.userValidationRemote;
import java.io.*;
import java.util.Iterator;
import java.util.List;
import java.util.Collection;
import javax.servlet.*;
import javax.servlet.http.*;
import javax.ejb.*;
* @author Ayo
* @version
public class userCheck extends HttpServlet {
@EJB
private UserTableFacadeLocal userTableFacade;
UserTable u;
String userFellow;
String pass;
String username,password;
/** Processes requests for both HTTP <code>GET</code> and <code>POST</code> methods.
* @param request servlet request
* @param response servlet response
protected void processRequest(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
/*con=null;
ps=null;
rs=null;
s=null;
*/response.setContentType("text/html;charset=UTF-8");
PrintWriter out = response.getWriter();
username=request.getParameter("username");
password=request.getParameter("password");
if(username==""||password=="")
showError("<b><font color=\"red\">Please fill in the required blanks.</font></b>",request,response);
else
List user=userTableFacade.findAll();
for(Iterator it=user.iterator();it.hasNext();)
u=(UserTable)it.next();
userFellow= u.getUsername();
pass=u.getPassword();
//out.println(" <b>"+elem.getTitle()+" </b><br />");
//out.println(elem.getBody()+"<br /> ");
//I used the following two lines to determing if im actually accessing the database and retrieving results, and I get all records in the table(usernames and passwords).
//BUT I NEED A SPECIFIC RECORD TO MATCH THE USERNAME AND PASSWORD FROM THE FORM AND IF IT DOES NOT MATCH,I REDIRECT TO THE ERROR PAGE.THAT'S WHERE IM STUCK.
out.println(userFellow);
out.println(pass);
/* if(username.equals(userFellow)&&password.equals(pass))
RequestDispatcher d=request.getRequestDispatcher("blah.jsp");
d.forward(request,response);
else
showError("<b><font color=\"red\">Invalid Login details!</font></b>",request,response);
private void showError(String errorMsg,HttpServletRequest request,HttpServletResponse response)throws ServletException,IOException
request.setAttribute("error_msg",errorMsg);
RequestDispatcher dispatcher=request.getRequestDispatcher("admin_error.jsp");
dispatcher.forward(request,response);
// <editor-fold defaultstate="collapsed" desc="HttpServlet methods. Click on the + sign on the left to edit the code.">
/** Handles the HTTP <code>GET</code> method.
* @param request servlet request
* @param response servlet response
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Handles the HTTP <code>POST</code> method.
* @param request servlet request
* @param response servlet response
protected void doPost(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Returns a short description of the servlet.
public String getServletInfo() {
return "Short description";
// </editor-fold>
I NEED HELP.ive been on this for 5 days and i cant seem to get a solution. I tried creating a method (private Collection findByUsername()) and(private Collection
findByPassword()) in the local interface that would supposedly return records based on input from the form but I got a null pointer and an ejb exception saying
unknown find method or something, as in ,or an error message that said i cant search records by name or something.I dont know. Or is it the query that is not
specific enough. I didnt seem to get the syntax right when i was trying to search by username and password.Please someone help me.
Ayo.

Hey everyone,
Is the question I posted that hard?
I even tried to just load a HTML <img src="picture.jpg"/> tag
on the login.jsp and even this won't show.
I'm thinking that the container, with the security mechanism, is blocking
styles and images???
Anyone...please help.
-Yuri

X.509 certificate based authentication with load balancer

I've been asked to implement certificate-based authentication (CBA)
on a weblogic cluster serving up web services. I've read through
Chapter 10 (security) and understand the "Identity Assertion" concept.
Environment:
Weblogic 8.1 cluster fronted by a load-balancer that handles SSL and
uses sticky-sessions.
Question:
If the load balancer is used to handle SSL, do I still need to turn
on SSL on the weblogic cluster in order to use CBA? Is there another
way to request the client's certificate?
If the above is yes, what is the minnimal level of SSL? Does it have
to be two-way?
If SSL has to be turned on is there any reason to use the load
balancer's SSL? Is there still a performance benefit?

Hi George,
If you want the client's cert, the server has to ask for it and this
implies two-way SSL. Normal one-way SSL the server provides the cert to
the client and the client decides if it wants to continue the handshake.
If the client is OK with the server certs and two-way SSL is configured
on the server, then the server will request the client send it's certs.
If the client certs are OK, then the pipe is established.
Concerning the load balancer I'm assuming it is simply providing a
tunnel, but I don't have the experience to comment and it is something I
would suggest that you that you seek guidance from our outstanding
support team [1] or drop a note in the security newsgroup [2] for the
experts to review.
Regards,
Bruce
[1]
http://support.bea.com
[email protected]
[2]
http://newsgroups.bea.com/cgi-bin/dnewsweb?cmd=xover&group=weblogic.developer.interest.security
George Coller wrote:
>
I've been asked to implement certificate-based authentication (CBA)
on a weblogic cluster serving up web services. I've read through
Chapter 10 (security) and understand the "Identity Assertion" concept.
Environment:
Weblogic 8.1 cluster fronted by a load-balancer that handles SSL and
uses sticky-sessions.
Question:
If the load balancer is used to handle SSL, do I still need to turn
on SSL on the weblogic cluster in order to use CBA? Is there another
way to request the client's certificate?
If the above is yes, what is the minnimal level of SSL? Does it have
to be two-way?
If SSL has to be turned on is there any reason to use the load
balancer's SSL? Is there still a performance benefit?

Certificate based authentication with iOS Client

Hello experts,
I have a question regarding the certificate based authentication in SAP Mobile Documents. With the Android Client it is "easy" possible to use certificate based authentication by just sending the user certificate to the Android device (using mail, MDM or whatever).
For the iOS App it is written that the user has to sync the certificate to the device using iTunes sync. Is this really the only possibility to bring the certificate to the iOS device so that the App can use it? I have successfully tested by adding the certificate using iTunes, but I cannot make it working using MDM to push the certificate to the device. SAP Mobile Documents just cant see the installed certificate.
Am I doing something wrong here?
Thanks for your help.
Ernst

Hi, I don't think this is supported on iOS right now. Something for future ....

DPS attempting certificate based authentication with Directory Servers

I'm running DPS 6.3 and DS 6.3.
I have DPS configured to always connect to the directory servers over SSL. This is working, however, all of the Direectory server error logs are showing certificate based bind attempts originating from the DPS. This results in err=32, since the certificate isn't stored in the ldap server. Anyone else seeing this type of behavior?
I checked the DPS Security config, and under the "Certificate to use with Data Sources" I have it set to 'None'.
Thanks.

Hello,
Certificate-based authentication cannot be proxied (it was designed to prevent man-in-the-middle attacks).
When the proxy receives a certificate-based bind (SASL EXTERNAL authentication method), it first validates the client certificate (signature, validity,trust etc), and map the certificate identity (subject) onto a LDAP identity. This is done by doing some LDAP lookups against the directory server. Then, that LDAP identity is used for subsequent LDAP requests to the directory servers. As the password is not available, the proxy must be configured to contact the directory server using proxied authorization method or using fixed credentials (used in conjunction with acis set on the proxy)
DPS 6.3 never uses the SASL/EXTERNAL (certificate-based) authentication method when it contacts directory servers.
When SSL is used between the proxy and the server, the proxy may present its own certificate to the directory server (controlled by the DPS security property you mentioned). It is possible to check if DPS stashes its own certificate when it establish a SSL channel to the directory server by using the ssltap tool [http://www.mozilla.org/projects/security/pki/nss/tools/ssltap.html] . If a certificate is passed, the No-Such-Object error you see might be generated during certificate validation by the directory server.
Hope this helps
-Sylvain

Performing form based authentication with entities

Hey everyone,
Im in a major dilemma.Im trying to perform form-based authentication using entities.I have created the entity class from the database,and I used a SLSB to access the bean method via JNDI(when I tried using dependency injection,there was an exception).I also cannot use hibernate as a persistent provider.I used toplink since it is the default in netbeans 5.5.1 and it did not raise any issues.But then,I noticed that toplink is most compatible with the oracle application server,and I use sun java system application server 9.1.I have not been able to successfully perform the authentication.
here's the code:note,there are still bugs as ive been going back and forth trying to find a solution and also because Ive been working with preexisting code.
model:
SLSB
* userValidationBean.java
* Created on 26 March 2008, 18:25
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import javax.ejb.Stateless;
import javax.ejb.Remote;
import java.util.List;
import javax.persistence.PersistenceContext;
import javax.persistence.EntityManager;
import javax.persistence.Query;
import Entities.UserTable;
import javax.transaction.UserTransaction;
import javax.annotation.Resource;
//the reason for the many comments is that im still debugging and there are still some bugs.Ive also been trying to go back and forth just
//to get a solution.
//the other accompanying classes had preexisting code i wrote earlier.
* @author Ayo
@Stateless
@Remote(userValidationRemote.class)
public class userValidationBean implements Entities.userValidationRemote {
@PersistenceContext private EntityManager manager;
@Resource private javax.transaction.UserTransaction tran;
/** Creates a new instance of userValidationBean */
public userValidationBean() {
//"SELECT u.username,u.password FROM UserTable u WHERE u.username =?1 and u.password=?2"
public boolean checkUser()
try
tran.begin();
UserTable user=new UserTable();
Query query=manager.createQuery("select u.username,u.password from u.user_table where u.username=:username and u.password=:password");
/*query.set("username",user.getUsername());
query.setParameter("password",user.getPassword());*/
query.setParameter("username",user.getUsername());
query.setParameter("password",user.getPassword());
userValidationBean ubean=(userValidationBean)query.getSingleResult();
boolean result=ubean==null?true:false;
tran.commit();
catch(Exception e)
System.out.println("Error:"+e);
// boolean result=ubean==null?true:false;
return result;
remote interface
package Entities;
import javax.ejb.Remote;
import Entities.UserTable;
* This is the business interface for userValidation enterprise bean.
@Remote
public interface userValidationRemote {
public boolean checkUser();
controller:servlet
* userCheck.java
* Created on 15 March 2008, 22:41
package servlets;
import Entities.UserTable;
import Entities.userValidationBean;
import javax.annotation.*;
import Entities.userValidationRemote;
import java.io.*;
import java.net.*;
import java.sql.*;
import javax.servlet.*;
import javax.servlet.http.*;
import javax.ejb.*;
import javax.naming.*;
import javax.persistence.*;
* @author Ayo
* @version
public class userCheck extends HttpServlet {
//@EJB userValidationRemote userRemote;
boolean checkUser;
String username,password;
/** Processes requests for both HTTP <code>GET</code> and <code>POST</code> methods.
* @param request servlet request
* @param response servlet response
protected void processRequest(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
/*con=null;
ps=null;
rs=null;
s=null;
*/response.setContentType("text/html;charset=UTF-8");
PrintWriter out = response.getWriter();
username=request.getParameter("username");
password=request.getParameter("password");
if(username==""||password=="")
//RequestDispatcher de=request.getRequestDispatcher("admin_error.jsp");
//de.forward(request,response);
//showError("<b><font color=\"red\">Invalid Login details!</font></b>",request,response);
showError("<b><font color=\"red\">Please fill in the required blanks.</font></b>",request,response);
else
try
Context ctx=new InitialContext();
userValidationRemote userRemote=(userValidationRemote)ctx.lookup("Entities.userValidationRemote");
checkUser= userRemote.checkUser();
//checkUser= userRemote.checkUser();
//return;
//checkUser(UserTable user);
catch(Exception e)
out.println("Error:"+e);
//userValidation.checkUser(UserTable user);
if(checkUser==true)
RequestDispatcher d=request.getRequestDispatcher("blah.jsp");
d.forward(request,response);
else if(checkUser==false)
// RequestDispatcher d=request.getRequestDispatcher("admin_error.jsp");
//d.forward(request,response);
showError("<b><font color=\"red\">Invalid Login details!</font></b>",request,response);
//call bean(stateless or stateful)which access method on entity that validates.
// checkUser(request,response);
/* TODO output your page here
out.println("<html>");
out.println("<head>");
out.println("<title>Servlet userCheck</title>");
out.println("</head>");
out.println("<body>");
out.println("<h1>Servlet userCheck at " + request.getContextPath () + "</h1>");
out.println("</body>");
out.println("</html>");
//out.close();
/* public synchronized void checkUser(HttpServletRequest request,HttpServletResponse response)throws ServletException,IOException
if(username==""&&password=="")
showError("<b><font color=\"red\">Please fill in the required blanks.</font></b>",request,response);
else
try
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select username,password from user_table where username=?and password=?");
ps.setString(1,username);
ps.setString(2,password);
rs=ps.executeQuery();
if(rs.next())
user=rs.getString(1);
pass=rs.getString(2);
//check user type,wether super admin,user or the other subadmins or a regular user.
checkType(request,response);
else
//redirect to admin error page,then close the connection.
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
con.close();
catch(Exception e)
private synchronized void checkType(HttpServletRequest request,HttpServletResponse response)throws ServletException,IOException
try
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select user_type,user_id,access_level from user_table where username=? and password=?");
ps.setString(1,user);
ps.setString(2,pass);
rs=ps.executeQuery();
if(rs.next())
user_type=rs.getString(1);
user_id=""+rs.getInt(2);
access_level=rs.getString(3);
if(user_type.equals("super")&&(access_level.equals("all")))
//create admin user session,add to the username and the user_id.
//redirect to super admin page,with access rights to create
//health admin,insurance admin and HMO admin.
//pretty cool stuff!
HttpSession session=request.getSession(true);
session.setAttribute("user",user);
session.setAttribute("user_id",user_id);
RequestDispatcher dispatcher=request.getRequestDispatcher("admin_user_page.jsp");
dispatcher.forward(request,response);
//session.setAttribute(user_id);
//remember to create a hidden field if you need to pass this information
//to another page and retrieve the super admin id to track his activities.
else if(user_type.equals("health administrator")&&(access_level.equals("Health")))
HttpSession session=request.getSession(true);
session.setAttribute("user",user);
session.setAttribute("user_id",user_id);
RequestDispatcher des=request.getRequestDispatcher("health_admin_user_page.jsp");
des.forward(request,response);
//check for other user types,health admin,hmo admin and insurance admin.
else if(user_type.equals("hmo administrator")&&(access_level.equals("HMO")))
HttpSession session=request.getSession(true);
session.setAttribute("user",user);
session.setAttribute("user_id",user_id);
RequestDispatcher d=request.getRequestDispatcher("hmo_admin_user_page.jsp");
d.forward(request,response);
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
else if(user_type.equals("insurance administrator")&&(access_level.equals("insurance")))
HttpSession session=request.getSession(true);
session.setAttribute("user",user);
session.setAttribute("user_id",user_id);
RequestDispatcher de=request.getRequestDispatcher("insurance_admin_user_page.jsp");
de.forward(request,response);
else if(user_type.equals("user")&&(access_level.equals("health")))
try
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql:http://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select staff_id from user_table where username=?and password=?");
ps.setString(1,username);
ps.setString(2,password);
rs=ps.executeQuery();
if(rs.next())
String staff_id=""+rs.getInt(1);
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select * from health_staff_table where staff_id=?");
ps.setString(1,staff_id);
rs=ps.executeQuery();
if(rs.next())
//retrieve the values from health staff and store them in variables.
//store important variables in user sessions e.g.staff_id,username,place of work for display in the web page.
//redirect to required page.
String first_name=rs.getString("first_name");
String last_name=rs.getString("last_name");
String work_place=rs.getString("place_of_work");
HttpSession session=request.getSession(true);
session.setAttribute("first_name",first_name);
session.setAttribute("last_name",last_name);
session.setAttribute("work_place",work_place);
session.setAttribute("staff_id",staff_id);
//redirect to user page.
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
catch(Exception e)
//catch exception and redirect to page.
else if(user_type.equals("user")&&(access_level.equals("HMO")))
try
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql:http://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select staff_id from user_table where username=?and password=?");
ps.setString(1,username);
ps.setString(2,password);
rs=ps.executeQuery();
if(rs.next())
String staff_id=""+rs.getInt(1);
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select * from hmo_staff_table where staff_id=?");
ps.setString(1,staff_id);
rs=ps.executeQuery();
if(rs.next())
//retrieve the values from HMO staff and store them in variables.
//store important variables in user sessions e.g.staff_id,username,place of work for display in the web page.
//redirect to required page.
String first_name=rs.getString("first_name");
String last_name=rs.getString("last_name");
String work_place=rs.getString("place_of_work");
HttpSession session=request.getSession(true);
session.setAttribute("first_name",first_name);
session.setAttribute("last_name",last_name);
session.setAttribute("work_place",work_place);
session.setAttribute("staff_id",staff_id);
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
catch(Exception e)
//catch exception and redirect to page.
else if(user_type.equals("user")&&(access_level.equals("insurance")))
try
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql:http://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select staff_id from user_table where username=?and password=?");
ps.setString(1,username);
ps.setString(2,password);
rs=ps.executeQuery();
if(rs.next())
String staff_id=""+rs.getInt(1);
Class.forName("com.mysql.jdbc.Driver");
con=DriverManager.getConnection("jdbc:mysql://localhost:3306/Health_Management_System","root","");
ps=con.prepareStatement("select * from insurance_staff_table where staff_id=?");
ps.setString(1,staff_id);
rs=ps.executeQuery();
if(rs.next())
//retrieve the values from insurance staff and store them in variables.
//store important variables in user sessions e.g.staff_id,username,place of work for display in the web page.
//redirect to required page.
String first_name=rs.getString("first_name");
String last_name=rs.getString("last_name");
String work_place=rs.getString("place_of_work");
HttpSession session=request.getSession(true);
session.setAttribute("first_name",first_name);
session.setAttribute("last_name",last_name);
session.setAttribute("work_place",work_place);
session.setAttribute("staff_id",staff_id);
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
else
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
catch(Exception e)
//catch exception and redirect to page.
else
//invalid login details.After all else fails.
showError("<b><font color=\"red\">Invalid Login details.</font></b>",request,response);
catch(Exception e)
private void showError(String errorMsg,HttpServletRequest request,HttpServletResponse response)throws ServletException,IOException
request.setAttribute("error_msg",errorMsg);
RequestDispatcher dispatcher=request.getRequestDispatcher("admin_error.jsp");
dispatcher.forward(request,response);
// <editor-fold defaultstate="collapsed" desc="HttpServlet methods. Click on the + sign on the left to edit the code.">
/** Handles the HTTP <code>GET</code> method.
* @param request servlet request
* @param response servlet response
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Handles the HTTP <code>POST</code> method.
* @param request servlet request
* @param response servlet response
protected void doPost(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Returns a short description of the servlet.
public String getServletInfo() {
return "Short description";
// </editor-fold>
view
<%@ page contentType="text/html; charset=utf-8" language="java" import="java.sql.*" errorPage="" %>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>Login</title>
<style type="text/css">

</style>
</head>
<body>
<table width="564" border="0" align="center">
<tr>
<td width="558" bgcolor="#CCCCCC" class="style1"><div align="center">
<p> </p>
<h1 class="style7">Welcome to HealthPort</h1>
<p>HealthPort Login</p>
<p><span class="style8">Today's date is:<%= new java.util.Date() %></span></p>
<form id="form1" name="form1" method="post" action="userCheck">
<p align="right" class="style3">Username
<label></label>
<input type="text" name="username" id="username" />
</p>
<p align="right" class="style3">Password
<input type="password" name="password" id="password" />
</p>
<p align="right" class="style3">
<span class="style6">
<label></label>
<label></label>
</span>
<span class="style5">
<label></label>
</span>
<label>
<input type="submit" name="button" id="button" value="Login" />
</label>
</p>
<div align="right">
</div></form>
<div align="right"><div align="left"><p align="right"> </p>
</div></div></div></td>
</tr>
<tr>
<td bgcolor="#CCCCCC" class="style1"> </td>
</tr>
</table>
</body>
</html>
so,that's about it.I'd appreciate it.I know this is a lot.I'm grateful
Ayo.

Hi.Im still having issues trying to perform form based authenticatin with entities.I tried this method but im getting errors on the marked lines.
controller servlet
* userCheck.java
* Created on 15 March 2008, 22:41
package servlets;
import Entities.UserTable;
import Entities.userValidationBean;
import javax.annotation.*;
import Entities.userValidationRemote;
import java.io.*;
import java.net.*;
import java.sql.*;
import javax.servlet.*;
import javax.servlet.http.*;
import javax.ejb.*;
import javax.naming.*;
import javax.persistence.*;
* @author Ayo
* @version
public class userCheck extends HttpServlet {
//@EJB userValidationRemote userRemote;
boolean checkUser;
String username,password;
/** Processes requests for both HTTP <code>GET</code> and <code>POST</code> methods.
* @param request servlet request
* @param response servlet response
protected void processRequest(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
/*con=null;
ps=null;
rs=null;
s=null;
*/response.setContentType("text/html;charset=UTF-8");
PrintWriter out = response.getWriter();
username=request.getParameter("username");
password=request.getParameter("password");
if(username==""||password=="")
showError("<b><font color=\"red\">Please fill in the required blanks.</font></b>",request,response);
else
try
Context ctx=new InitialContext();
userValidationRemote userRemote=(userValidationRemote)ctx.lookup("Entities.userValidationRemote");
(error on this line-saying ')' expected and no matter if i add ) there is still erro)userRemote.authenticate(String p_user,String p_password);
catch(Exception e)
out.println("Error:"+e);
if(checkUser==true)
RequestDispatcher d=request.getRequestDispatcher("blah.jsp");
d.forward(request,response);
else if(checkUser==false)
showError("<b><font color=\"red\">Invalid Login details!</font></b>",request,response);
private void showError(String errorMsg,HttpServletRequest request,HttpServletResponse response)throws ServletException,IOException
request.setAttribute("error_msg",errorMsg);
RequestDispatcher dispatcher=request.getRequestDispatcher("admin_error.jsp");
dispatcher.forward(request,response);
// <editor-fold defaultstate="collapsed" desc="HttpServlet methods. Click on the + sign on the left to edit the code.">
/** Handles the HTTP <code>GET</code> method.
* @param request servlet request
* @param response servlet response
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Handles the HTTP <code>POST</code> method.
* @param request servlet request
* @param response servlet response
protected void doPost(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Returns a short description of the servlet.
public String getServletInfo() {
return "Short description";
// </editor-fold>
view
<%@ page contentType="text/html; charset=utf-8" language="java" import="java.sql.*" errorPage="" %>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>Login</title>
<style type="text/css">

</style>
</head>
<body>
<table width="564" border="0" align="center">
<tr>
<td width="558" bgcolor="#9DACBF" class="style1"><div align="center">
<p> </p>
<h1 class="style7">Welcome to HealthPort</h1>
<p>HealthPort Login</p>
<p><span class="style8">Today's date is:<%= new java.util.Date() %></span></p>
<form id="form1" name="form1" method="post" action="userCheck">
<p align="right" class="style3">Username
<label></label>
<input type="text" name="username" id="username" />
</p>
<p align="right" class="style3">Password
<input type="password" name="password" id="password" />
</p>
<p align="right" class="style3">
<span class="style6">
<label></label>
<label></label>
</span>
<span class="style5">
<label></label>
</span>
<label>
<input type="submit" name="button" id="button" value="Login" />
</label>
</p>
<div align="right">
</div></form>
<div align="right"><div align="left"><p align="right"> </p>
</div></div></div></td>
</tr>
<tr>
<td bgcolor="#CCCCCC" class="style1"> </td>
</tr>
</table>
</body>
</html>
SLSB (implements userValidationRemote)
* userValidationBean.java
* Created on 26 March 2008, 18:25
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import javax.ejb.Stateless;
import javax.ejb.Remote;
import javax.persistence.PersistenceContext;
import javax.persistence.EntityManager;
import javax.persistence.Query;
import Entities.UserTable;
import javax.annotation.*;
//import javax.transaction.UserTransaction;
* @author Ayo
@Stateless(mappedName="ejb/facade/userValidationBean")
@Remote(userValidationRemote.class)
(error on this line saying can't find class TransactionManagement)@TransactionManagement(value=TransactionManagementType.CONTAINER)
public class userValidationBean implements Entities.userValidationRemote {
@PersistenceContext(unitName="HealthInsuranceApp-ejbPU") private EntityManager manager;
/** Creates a new instance of userValidationBean */
public userValidationBean() {
//"SELECT u.username,u.password FROM UserTable u WHERE u.username =?1 and u.password=?2"
public boolean authenticate(String p_user,String p_password)
UserTable m_user=manager.find(UserTable.class,p_user);
if(m_user!=null)
return m_user.getPassword().equals(p_password);
return false;
Entity
* UserTable.java
* Created on 29 March 2008, 13:24
* To change this template, choose Tools | Template Manager
* and open the template in the editor.
package Entities;
import java.io.Serializable;
import javax.persistence.Column;
import javax.persistence.Entity;
import javax.persistence.Id;
import javax.persistence.Table;
* Entity class UserTable
* @author Ayo
@Entity(name="qs_UserPwd")
@Table(name = "user_table")
public class UserTable implements Serializable {
@Id
@Column(name = "user_id", nullable = false)
private Integer userId;
@Column(name = "username")
private String username;
@Column(name = "password")
private String password;
@Column(name = "user_type")
private String userType;
@Column(name = "access_level")
private String accessLevel;
@Column(name = "staff_id")
private Integer staffId;
@Column(name = "staff_type", nullable = false)
private String staffType;
@Column(name = "time_created")
private String timeCreated;
@Column(name = "time_modified")
private String timeModified;
@Column(name = "time_logged_in")
private String timeLoggedIn;
@Column(name = "time_logged_out")
private String timeLoggedOut;
@Column(name = "created_by")
private String createdBy;
/** Creates a new instance of UserTable */
public UserTable() {
* Creates a new instance of UserTable with the specified values.
* @param userId the userId of the UserTable
public UserTable(Integer userId) {
this.userId = userId;
* Creates a new instance of UserTable with the specified values.
* @param userId the userId of the UserTable
* @param staffType the staffType of the UserTable
public UserTable(Integer userId, String staffType) {
this.userId = userId;
this.staffType = staffType;
public UserTable(String p_user,String p_password)
setUsername(p_user);
setPassword(p_password);
* Gets the userId of this UserTable.
* @return the userId
public Integer getUserId() {
return this.userId;
* Sets the userId of this UserTable to the specified value.
* @param userId the new userId
public void setUserId(Integer userId) {
this.userId = userId;
* Gets the username of this UserTable.
* @return the username
public String getUsername() {
return this.username;
* Sets the username of this UserTable to the specified value.
* @param username the new username
public void setUsername(String p_user) {
p_user = username;
* Gets the password of this UserTable.
* @return the password
public String getPassword() {
return this.password;
* Sets the password of this UserTable to the specified value.
* @param password the new password
public void setPassword(String p_password) {
p_password=password;
* Gets the userType of this UserTable.
* @return the userType
public String getUserType() {
return this.userType;
* Sets the userType of this UserTable to the specified value.
* @param userType the new userType
public void setUserType(String userType) {
this.userType = userType;
* Gets the accessLevel of this UserTable.
* @return the accessLevel
public String getAccessLevel() {
return this.accessLevel;
* Sets the accessLevel of this UserTable to the specified value.
* @param accessLevel the new accessLevel
public void setAccessLevel(String accessLevel) {
this.accessLevel = accessLevel;
* Gets the staffId of this UserTable.
* @return the staffId
public Integer getStaffId() {
return this.staffId;
* Sets the staffId of this UserTable to the specified value.
* @param staffId the new staffId
public void setStaffId(Integer staffId) {
this.staffId = staffId;
* Gets the staffType of this UserTable.
* @return the staffType
public String getStaffType() {
return this.staffType;
* Sets the staffType of this UserTable to the specified value.
* @param staffType the new staffType
public void setStaffType(String staffType) {
this.staffType = staffType;
* Gets the timeCreated of this UserTable.
* @return the timeCreated
public String getTimeCreated() {
return this.timeCreated;
* Sets the timeCreated of this UserTable to the specified value.
* @param timeCreated the new timeCreated
public void setTimeCreated(String timeCreated) {
this.timeCreated = timeCreated;
* Gets the timeModified of this UserTable.
* @return the timeModified
public String getTimeModified() {
return this.timeModified;
* Sets the timeModified of this UserTable to the specified value.
* @param timeModified the new timeModified
public void setTimeModified(String timeModified) {
this.timeModified = timeModified;
* Gets the timeLoggedIn of this UserTable.
* @return the timeLoggedIn
public String getTimeLoggedIn() {
return this.timeLoggedIn;
* Sets the timeLoggedIn of this UserTable to the specified value.
* @param timeLoggedIn the new timeLoggedIn
public void setTimeLoggedIn(String timeLoggedIn) {
this.timeLoggedIn = timeLoggedIn;
* Gets the timeLoggedOut of this UserTable.
* @return the timeLoggedOut
public String getTimeLoggedOut() {
return this.timeLoggedOut;
* Sets the timeLoggedOut of this UserTable to the specified value.
* @param timeLoggedOut the new timeLoggedOut
public void setTimeLoggedOut(String timeLoggedOut) {
this.timeLoggedOut = timeLoggedOut;
* Gets the createdBy of this UserTable.
* @return the createdBy
public String getCreatedBy() {
return this.createdBy;
* Sets the createdBy of this UserTable to the specified value.
* @param createdBy the new createdBy
public void setCreatedBy(String createdBy) {
this.createdBy = createdBy;
* Returns a hash code value for the object. This implementation computes
* a hash code value based on the id fields in this object.
* @return a hash code value for this object.
@Override
public int hashCode() {
int hash = 0;
hash += (this.userId != null ? this.userId.hashCode() : 0);
return hash;
* Determines whether another object is equal to this UserTable. The result is
* <code>true</code> if and only if the argument is not null and is a UserTable object that
* has the same id field values as this object.
* @param object the reference object with which to compare
* @return <code>true</code> if this object is the same as the argument;
* <code>false</code> otherwise.
@Override
public boolean equals(Object object) {
// TODO: Warning - this method won't work in the case the id fields are not set
if (!(object instanceof UserTable)) {
return false;
UserTable other = (UserTable)object;
if (this.userId != other.userId && (this.userId == null || !this.userId.equals(other.userId))) return false;
return true;
* Returns a string representation of the object. This implementation constructs
* that representation based on the id fields.
* @return a string representation of the object.
@Override
public String toString() {
return "Entities.UserTable[userId=" + userId + "]";
please what do I do? or is there a better way? seems like my appserver(sun java system app server 9.1)doesnt support dependency injection as
there's always an exception in the server log when i try it.i use the default transaction provider toplink because use of any of the others raises an exception and my application index page never shows. please i need help? I want to be able to succesfully perform this authentication as its the only way i can move to the next level
Ayo.

IEEE 802.1x Port based Authentication with Restricted VLAN

Similar Messages

Maybe you are looking for