If I turn off AirPort Extreme will it loose it's settings?

I am a bit worried about the issue of radio signals and cancer. I want to turn it off during the night, but will it lose it's settings?

THe AirPort Extreme will not lose its network settings if you turn it off at night.
As far as potential issues, you are picking up far more radiation from cordless phones, cell phone towers, radio and television signals, aircraft, police and emergency signals, overhead electrical wires, the AC wiring in your home, and countless other sources.
WiFi would be the least of your worries compared to other sources of constant daily RF radiation.

Similar Messages

Turn off airport extreme

How can I turn off airport extreme during certain times of the day so my kids can't use wifi?

You might want to take a look at the Timed Access settings in AirPort Utility, which will allow you specify the times each day that everyone will be allowed to connect to the network.
Or, you can individualize this, and the set up individual "rules" for each of the kids' devices that allow them to connect using certain times each day....while your devices have unlimited access.

Turn off Airport Extreme without unplugging?

Is there a way to turn off the wireless siganl coming from the Airport Extreme (without unplugging it from the wall) at certain times? I.E. turn it off after bedtime to prevent kids from wirelessly gaming into the wee hours of the night or surfing the net at all hours?

Your other option is to use the Access Control option (within the AirPort Utility) to set specific times that their computers can connect to the AirPort. This way you won't have to enable/disable the wireless radios at all.

Turning off airport extreme

I am a brand new mac os user. I just switched from a pc.
How do you turn off the airport extreme? Could it harm it to leave it on all the time? Are you supposed to leave it on all the time?

I assume by "airport extreme" you mean one of Apple's AirPort Extreme base station (AEBS).
How do you turn off the airport extreme?
Unplug it.
Could it harm it to leave it on all the time?
Yes
Are you supposed to leave it on all the time?
It is designed to be on all the time.

My new AirPort Extreme will not turn on anymore, no lights when plugged in.

My new AirPort Extreme will not turn on anymore, no lights when plugged in. I just bought it a few days ago. It has been working fine. I left the house for most the day and when returning home it would turn back on. I have tried to plug it into other outlets...nothing, I've tried the reset button...Nothing.

That is reported here a few times.. just take it straight back to apple or place of purchase for immediate exchange.

Turn Off / Airport / Menu Item

Hello,
I try to make an applescript to turn off Airport by menu items
I've try this (see below) but it doesn't work on Leopard (french version).
I've already turn off "Enable Access for assistive devices" in Universal Access.
Thanks in advance for your help,
Regards,
Grégoire
*tell application "System Events"*
*click menu bar item 1 of menu bar 1 of application process "SystemUIServer"*
*click menu item "Désactiver AirPort" of menu 1 of menu bar item 1 of menu bar 1 of application process "SystemUIServer"*
*end tell*

The menu position isn't set so you can't assume a numerical index, but you can go through the menu items looking for the one you want. There was an earlier topic about scripting the Airport menu, so I just looked up some keys in the French localized strings. The "Enable Access for assistive devices" will need to be turned on, but the following script should do it:
<pre style="
font-family: Monaco, 'Courier New', Courier, monospace;
font-size: 10px;
margin: 0px;
padding: 5px;
border: 1px solid #000000;
width: 720px;
color: #000000;
background-color: #FFDDFF;
overflow: auto;"
title="this text can be pasted into the Script Editor">
tell application "System Events" to tell process "SystemUIServer"
tell menu bar 1
set menu_extras to value of attribute "AXDescription" of menu bar items
repeat with the_menu from 1 to the count of menu_extras
if item the_menu of menu_extras is "Menu supplémentaire AirPort" then tell menu bar item the_menu
click
delay 0.5
click menu item "Activer AirPort" of front menu
-- click menu item "Désactiver AirPort" of front menu
delay 0.5
end tell
end repeat
end tell -- menu bar 1
end tell
</pre>

Cannot turn off airport on Imac and PowerBook

I cannot turn off airport on iMac 17" intel (late 2006) and G4 powerbook. One common thing is:
I got rid off .plist files (airport related) on both machines prior to putting new AE in to mix. I set up AE and not only I cannot establish wireless on both machines I cannot turn airport on both as well. Old G4 iMac (3rd machine that was not altered) works.
What did I get rid off?
iMac gives me this:
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x14E4, 0x87)
Wireless Card Locale: USA
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.46.9)
Current Wireless Network: AirPort is currently turned off
While Network pref. and icon in menus says airport is on. (Same with powerbook)
Any suggestions?
Just to ad to confusion. This is replacement AE. First one after firmware upgrade (7.3.2) started to misbehave (very weak signal, mostly). I did downgrade to 7.3.1 but after couple of days I went for factory one (firmware that is), and here I am.

…after waking both computers from sleep situation is reversed. Airport is off and I cannot turn it on. After restart I am back to Airport on (not able to connect, while showing networks to join) and not able to turn off.

How do i turn off airport express bridge

How do i turn off airport express bridge?

Only exception was that it went into bridge mode and I cannot configure an IP camera that was working prior.
Bridge Mode is the correct setting for the AirPort Express since your "upgraded" Xfinity device is a modem/router or gateway device.
So, you already have a router set up on the network. Bridge mode must be used on the AirPort Express to avoid having two devices both trying to act as routers on the network.
That would create IP address conflicts and other problems like Double NAT.
Since the Xfinity device is now your network router, you must configure the port settings for your camera on the Xfinity modem/router. The AirPort Express will simply pass through those settings since it is in Bridge Mode.
You may need to check with Xfinity support on how to set up port forwarding if the owners guide does not cover that topic.

2013 MBP 2.5 i5 4Gig 500MBHDD boots slow. It finishes post in the same time as an identical MBP, and then hangs for 30 seconds on one of the ethernet adapters, before finishing the boot. Once booted it is normal.   Turning off airport changes nothig.

2013 MBP 2.5 i5 4Gig 500MBHDD boots slow. It finishes post in the same time as an identical MBP, and then hangs for 30 seconds on one of the ethernet adapters, before finishing the boot. Once booted it is normal.   Turning off airport changes nothing. Hardline adapter is not plugged in. Thunderbolt adapter is not used. Bluetooth is off. Did this out of box. Identical MBP boots to login screen in 36 seconds. Disk repair, permission repair, and safe mode boot have
already been done, no change. Boot time is consistent. Hangs at the same place each time. Right after post. Bad adapter?
Comments, solutions please.

... and so ... now a few days later, success.   I ran
your software but it told me nothing I hadn 't seen
in verbose boot.
Consistently, following good post, the boot hung
for 30 seconds on the adapters, (cards, chips, NICs.
Ethernet cards, whatever you prefer to call them)
either the airport card or the hard line. It would then
proceed at normal pace to the login screen.
Since it came out of the box that way, software
conflict was not a go. I guessed glitched driver or
fetch instruction. I zapped the PRAM (cleared
NVRAM) and reloaded the OS, updates, Garage Band,
iPhoto (one of Apple's true dogs in an otherwise
rare arena) iMovie, Photoshop, Lightroom, their
updates, and my files.   MBP pro now boots to login
in 31 seconds. Note I have turned off as much gee
whiz, rubber band scroll, global swiping and other
hubcaps and hood ornaments as befits how like
things ... and turned off all the Asian and other fonts
I will. ever use.
Best guess ... corrupt driver or corrupt fetch script ...
bad server squirt at factory load.
Thanks for your help, Cheers!

Airport Extreme will not show USB drive installed Solved!

Airport Extreme will not show USB drive installed Solved... At least for me!
Here's what I had to do to make it work with the newest 7.3.1 firmware.
Ready for this? No Joke Really!
1. Connect your USB drive to the Airport Extreme.
2. Turn it on.
3. Open the Airport Utility.
4. Go to Manual Setup.
5. Choose Disks and File Sharing.
Yep, we are going to set file sharing before we even see the disk we want to share!
You (I) had to set File Sharing on and Share Disks over Ethernet checked as well as set the Work Group (In my case). THEN restart the Airport Extreme.
After it re-started... My USB Drive was now present and ready for use.
I also dis-allowed Guest access. I re-started ALL computers in my network, both Windows and MAC. The USB drive held and works GREAT!
I know... Most of you thought this was a joke, It's not!
I tried everything to get the USB drive to work and failed every time just like most other people. Doing it this way worked like a charm.
Go Figure huh!
Hope this helps someone with this issue.
Message was edited by: DonaldH

How was the usb hard drive formatted? Was it NTFS, FAT32, or HFS+?

Can I turn my airport extreme when not in use?

can I turn my airport extreme when not in use?

Why?
The power saving will be negligible, and it may take time to re-establish a connection to your ISP's Network.

My airport extreme will not connect to the Internet

My airport extreme will not connect to my toshiba router. I connected it to my office internet this morning but when I hooked it up at home it simply will not connect. I have tried resetting all the settings and have had no luck. It did work once upon a time. I currently have my airport express hooked up so I know there is connectivity.

I could never figure it out after trying everything I could and going to the genius bar I ended up just purchasing another extreme. The really funny thing is that I can set up a network between the two and it works fine. I am using it at work now with out any problems so I guess there is really no loss :-?

External hard drive connected to my airport extreme will no longer open, when navigating to it in Finder, the Finder window quits and reopens, cannot access hard drive, it is visible in airport utility, since the problem began I have updated firmware

External hard drive connected to my airport extreme will no longer open, when navigating to it in Finder, the Finder window quits and reopens, cannot access hard drive, it is visible in airport utility, since the problem began I have updated firmware on Extreme as well as both of my Airport Expresses. Hard drive is USB connected to Extreme.

Reboot the USB drive.. assuming it is powered.. or unplug and replug a self-powered drive.. (you should not use self-powered drives on AE before the latest model.. always use a powered hub).
Does the drive now appear in finder..
If not reboot both drive and the AE.. it should now appear.
If it doesn't work with direct connection try a powered hub.. that can help.

My Airport Extreme will no longer let new user connect

The Airport Extreme will not allow new users to connect to via wifi. The users that are currently on the wifi are able to continue using the wifi, but new users cannot connect. I have tried resetting to the factory settings. But the problem has returned. I have a model A1408.

Reboot the USB drive.. assuming it is powered.. or unplug and replug a self-powered drive.. (you should not use self-powered drives on AE before the latest model.. always use a powered hub).
Does the drive now appear in finder..
If not reboot both drive and the AE.. it should now appear.
If it doesn't work with direct connection try a powered hub.. that can help.

I was on the phone last night and my phone randomly turned off. It will not come back on even when I have tried to hold the home button and the power button together while being plugged into the computer. What do I do?

I was on the phone last night and my phone randomly turned off. It will not come back on even when I have tried to hold the home button and the power button at the same time, while being plugged into the computer? What do I do?

Plug it into power for at least 15 minutes. If it doesn't automatically come on, try a reset... press the home and sleep (on/off) buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.

If I turn off AirPort Extreme will it loose it's settings?

Similar Messages

Maybe you are looking for