If using timed access to shut down a device at 11:00 pm, if currently online will it automatically shut down?

The wireless device will not shut down, but it will lose its connection to the wireless network at a fraction of a second before 11:01 PM.
If you have an iPhone or iPad with 4G service, the device will switch over to 4G within a few seconds.

Similar Messages

Using TImed Access mode on Airport Extreme with other routers in bridge mode. Not working as expected.

I am trying to setup timed access mode on my airport extreme in order to limit the times devices can connect to my network, but I am having some trouble.
My setup is as follows Cable Modem ---> Airport Extreme ---> Netgear router
The Airport is running DHCP and the Netgear is in bridge mode. The only purpose of the Netgear is to provide a wireless access point for older b/g wifi devices. The Netgear is connected to the Airport by an ethernet cable from one of its LAN ports. All ip addresses are supplied by the Airport.
When I list a device mac number in the Airport extreme's timed access table it does seem to block the device if the device trys to connect to the airport's wireless service, but the device is still able to obtain service through the Netgear wireless service. I want the device to be blocked on both wireless networks. I thought this would work since all DHCP is on the airport. Why is the Airport allowing the device to connect when it comes in through the Netgear?
In this example the device I am trying to block is 5c:59:48:ba:28:d2.
Looking at the log on the airport I see the following entry when the device (when permitted) connects to the airport wireless
Nov 30 22:43:12
Severity:5
Associated with station 5c:59:48:ba:28:d2
If instead the device connects to the Netgear wireless I see the following log entry on the airport (this connection gets through even if the mac address above is listed as blocked on the airport)
Dec 01 10:46:29
Severity:5
Connection accepted from [fe80::223:12ff:fe29:acfe%bridge0]:54774.
It appears that the Netgear router (while bridging the network) is somehow modifying the mac address format in a way that the airport does not recognise it as the device to block.
What can I do to fix this?
Thanks.

The Netgear wireless server has control over what what devices are allowed to connect.
Unless you tell the Netgear what devices you want to allow to connect, it will allow any wireless device to connect as long as it knows the wireless network password.
IF.... .you were using two AirPort Extremes, and not a Netgear, the two Extremes would communicate to each other....so you would only have to enter Timed Access settings on one router and other AirPort would automatically pick those settings up.
But, even this was not the case until the last year or so when Apple updated firmware. A few years ago, you might have had 2 Apple AirPort Extremes on the network, but you still had to manually set up Timed Access on both devices separately.
Bottom line, you need to setup the equivalent of Timed Access on the Netgear router.

Have just found a hickup on the Lion software 10.7.2 When using a access point that you name with letters that is only in Norwegian æøå you will loose connections and only get time out. So the solution will be to rename the access point.

Any solution beside to rename the wifi access point without the spesial Norwegian letters æøå?

Your points match mine pretty well,though here are some thoughts:
1. I thought about this theory myself this morning (iTunes possibly causing more issues), but I haven't been able to verify it.
2. When I set up a new user it seemed better for a while, but the issue croppped back up. Yesterday I fully wiped the machine and reinstalled from scratch. I did not reimport my user from TimeMachine, but the problem has come back. My thinking was that I might have some really old software or prefs hanging around causing the issue. No dice.
3. This is my current theory of the issue, so my next step will be to pull the RAM from Crucial and see how the system behves. IF that doesn't eliminate the problem, I'll pull the factory installed RAM and replace it with the 3rd party RAM. The odd thing is how many people seem to have similar issues - I know two personally, and have seen several posts on forums. I think the most common point for this happening was the 10.7.2 update, which would point to software as the culprit.
4. That matches my experience.
My hope is that this will be repaired in the forthcoming 10.7.3 release (current production version is 10.7.2), but otuside of what I noted above, I'm at a loss.

Timed Access controlling Main and Guest Network

I have a Time Capusle 4G running software v7.5.2. I am running a Guest Network as well as a closed network.
In the Timed Access window i have default set to "no access". Then, all the computers that are allowed access to the main network are on the list. My guest network is broadcasting but when a user tries to connect to it, they get an "Unable to connect" message. If I change the default access in Timed Access to "Everyday", users are then able to connect to the Guest network again.
Obviously, this is a bug/missing feature and has been for several software revisions. I don't want people accessing the main network that aren't on the timed access list. However, I still want guest users to access the Guest Network, without using MAC address filtering on the Guest Network.
It looks to me that the Timed Access window is controlling the restriction of the Guest and Main network. Which renders the Guest Network feature pretty much useless.
Hopefully this will be addressed in the near future. If other people are experiencing this problem, Please let me know.
-Ghost

It looks to me that the Timed Access window is controlling the restriction of the Guest and Main network.
Your observation is correct. Access control using Timed Access is an ALL or NOTHING feature for both the Main and Guest networks. The Guest network is basically a VLAN function.

Using MS Access 2010 on Windows via Bootcamp

Using MS Access 2010 on Windows via Bootcamp
I am wanting to do an online course which uses MS Access 2010. I am using an Apple Mac and thought I could use Bootcamp to set up a Windows partition to use the software.
My query is once I have created a database with MS Access 2010 in Windows on my mac, is the database essentially useless for my future mac work?
Hope someone can help
Daisy

daisyvflower wrote:
Thanks for the email.
I do think converting will end up being complicating. Do you know what Office for Mac is like, is it similar to MS Access? If so, I could do the course using MS Access and then buy Office for Mac and teach myself how to create databases using office.
As I mentioned there is no Access for Mac. Microsoft never made one. Office for Mac includes Word, Excel, Powerpoint (and Outlook for the Business edition.) And even these are missing some features of their Windows versions. (e.g.: Excel macros often don't work on the Mac version of Excel.)
You can bring over your general knowlege of database programming (e.g.: relationships, joins, normalizing,) to any database product such as MSSQL, MySQL, Oracle Database, Filemaker, Alpha5, OpenOffice, etc. But none of those other database products will open a database file made in Access. (Or rather, may have very limited ability to open very simple databases, but you'll probably lose the relationship links.) So your Access training won't be a total loss, but you'll need to learn the specifics of whatever database product you eventually use.

When I choose a photo to share on face book a drop down box appears with the message, Face book didn't recognise the information you entered for the account this is my Face book login information I use to access my face book page how can I overcome the b

when I choose a photo to share on face book a drop down box appears with the message, Face book didn't recognise the information you entered for the account this is my Face book login information I use to access my face book page how can I overcome this.

Delete abd re-enter your Facebook account information jnder the accounts tab in the iPhoto preferences
You may also want to take a look at the user tip for Facebook problems
LN

HT201270 I have an iPad 3rd gen. A carrier settings update notification has appeared on my screen, and it doesn't do anything when I press either 'update' or 'not now' . Because the notification is still there, I am unable to use any apps or shut it down.

I have an iPad 3rd gen. A carrier settings update notification has appeared on my screen, and it doesn't do anything when I press either 'update' or 'not now' . Because the notification is still there, I am unable to use any apps or shut it down. What should I do?

Have you tried a reset by pressing and holding the sleep/wake button and the home button for 20 seconds (maybe longer) until the Apple logo appears, ignore the red slider. Then turn back on. You won't lose any data doing the reset.

2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior. No system changes.

2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior. No system changes.

2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior. No system changes.

Not working right-will not let me type a new emall, pull contacts, also will not let me use wireless printer-kept shutting down windows.

firefox will not let me type in yahoo mail as new email. will not pull up contacts. also, when I use wireless printer-it shuts down windows.

Couple of points...
DJ_Jynxx wrote:
The thing is, this MUST be an Audition CC issue for two reasons. One, everything worked fine in CS6, which I was using right before I upgraded to CC. I even did a clean install of it by removing CS6 completely.
All versions of Audition can co-exist on the same machine quite happily - there is no interaction between them at all, and the system was designed to be like this. So there's nothing to stop you keeping CS5.5, CS6, CC and even Audition3 on the same machine.
The other thing I'm wondering about is Windows 8. There have been a considerable number of complaints about this doing weird things, including with Audition. I have a system that in many ways is very similar to yours, except that I don't overclock the mobo, and use a professional sound device (or two) with it (RME). The major difference though is that I use Windows 7 pro 64-bit, and I haven't had any of these problems at all. Yes I use it for a living, as well, but I don't bother with multiple DAWs - don't have time for all that these days. But I do use iZotope's RX software in its standalone mode without any difficulty.
I'm not claiming that Audition CC is trouble-free - any number of Mac users will confirm that - but people running it on W7 certainly seem to have far fewer problems with it. It may also be worth trying an uninstall-reinstall of CC - you never know. But differences in preview quality certainly point towards audio drivers, I'm afraid...

I don't have access to iTunes store. Everytime I try to access iTunes shuts down

I there.
I don't have access to the iTunes Store. Every time i try to access iTunes shuts down.
Thanks

Thank you. I did exactly what you suggested... I called Apple directly and they walked me through the entire process and I could. It have been more pleased with the service they provided!!!!

After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.

After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.
I have a Time Capsule and an Airport express and when I change access control parameters on whatever one of those
two devices through Airport Utility its duplicating the same setup on the other device !
What a mess !
I had to choose "Not Enabled" in the Access Control stup window.
Has anyone experienced same problem ?
Jean.

I did downgraded firmware to 7.5.2 ...
and the Acess Control Setting from Airport Utility is back to normal behaviour.
Jean.

I turned off Internet access, using airport timed access control. Now, I can't turn it back on. The base station can't be found. Please help.

I turned off Internet access, using airport timed access control. Now, I can't turn it back on. The base station can't be found. Please help.

Can you take a look at this one and offer your opinion please?
https://discussions.apple.com/message/21889032#21889032

After closing Firefox, at times I have to use task manger to shut down firefox.exe*32 at times,

As my title says, after closing Firefox, at times I have to use task manger to shut down firefox.exe*32 at times. I've left it running for up to 5 minutes to see if it shuts down/closes and it doesn't. I've also reloaded Firefox. My system is a Lenovo H210 with 3 gig of Ram and no added video card, the OS is Windows 7 Ultimate 64 bit SP1. I realize the memory is on the small side. I did try to update VLC player this morning to V 2.1.2 but it fails to run after instal due to file errors.
Bill

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you.

How do I set timed access for specific mac addresses?

My daughter tends to stay up late on social media long after we've asked her to go to bed, so I'd like to use the AirPort Utility to just shut off her internet access during set hours. It looks fairly straightforward to set up, however, I don't know how to find her MAC address for her iPod. Can anyone enlighten me?

iPods, IPhones, and iPads do not have a MAC Address.
On the iPod home screen, tap Settings
Scroll down and tap General
Tap About
Scroll down to locate the Wi-Fi Address
Use the WiFi Address of an iPod, iPhone, or iPad in place of the MAC Address when you are setting up rules in Timed Access.

How to configure OraMTS to allow WCF using MSDTC access OracleDB On unix?

How to configure OraMTS to allow WCF using distributed transactions to access the ORACLE database On Linux/Unix ?
Env:
1. DB-tier node , ORACLE database (version: 11.2.0.1.0) on Redhat Linux server ;
2. middle-tier node ,Both the client, the MS DTC and Oracle MTS run on the same computer , Win7 x64 OS , installed .Netframework 4.0, ODP.net (ODAC112030), and configure the component services in a distributed transaction;
Has done the configuration:
1. ORACLE database on a Linux server (version: 11.2.0.1.0) has execute oramtsadmin.sql script;
2.ORACLE database on a Linux server (version: 11.2.0.1.0) has execute the following script, Creating an Access Control List (ACL);
BEGIN
-- Create the new ACL, naming it "OraMTSadmin.xml", with a description.
-- This provides the OraMTS administrative user e.g. MTSADMIN user FOO
-- the privilege to connect
DBMS_NETWORK_ACL_ADMIN.CREATE_ACL('OraMTSadmin.xml',
'Allow usage to the UTL network packages',
'ORAMTS', TRUE, 'connect');
-- Now grant privilege to resolve DNS names to the OraMTS administrative user
DBMS_NETWORK_ACL_ADMIN.ADD_PRIVILEGE('OraMTSadmin.xml' ,
'ORAMTS', TRUE,'resolve');
-- Specify which hosts this ACL applies to, in this case we are allowing
-- access to all hosts. if one knew the list of all Windows middle-tier,
-- these could be added one by one.
DBMS_NETWORK_ACL_ADMIN.ASSIGN_ACL('OraMTSadmin.xml','*');
END;
3. ORACLE database on a Linux server has set JOB_QUEUE_PROCESSES = 1000;
4. restart Oralce;
5.Test code as follows :
using System;
using System.Collections.Generic;
using System.Linq;
using System.Text;
using JetSun.Infrastructure;
using Microsoft.VisualStudio.TestTools.UnitTesting;
using JetSun.Infrastructure.ServiceModel;
using JetSun.DataModel.Cis;
using JetSun.TestFramework;
using System.IO;
using System.Data.EntityClient;
using System.Data.Objects;
using ConsoleApplicationTest;
using System.Transactions;
namespace Core.Tests
[TestClass]
public class EfOracleTest
public TestContext TestContext { get; set; }
[TestMethod]
public void GetEntities()
//string cn = "DATA SOURCE=HIS30;DBA PRIVILEGE=SYSDBA;PASSWORD=jetsun;PERSIST SECURITY INFO=True;USER ID=SYS;enlist=true";
string cn = "DATA SOURCE=HIS30;DBA PRIVILEGE=SYSDBA;PASSWORD=mtssys;PERSIST SECURITY INFO=True;USER ID=mtssys;enlist=true";
DbsSetting s = new DbsSetting(Dbs.IP, DbsProvider.Oracle, cn);
Runtime.SetDeploymentDir(TestContext.TestDeploymentDir);
File.Copy("E:\\VSTS\\MedicalHealth\\bin\\Debug\\DataModel.Cis.Oracle.dll", Path.Combine(TestContext.TestDeploymentDir, "DataModel.Cis.Oracle.dll"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.csdl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.csdl"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.ssdl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.ssdl"));
//File.Copy(@"E:\VSTS\MedicalHealth\DataModel\Oracle\DataModel.Cis\EdmDiagnose.msl", Path.Combine(TestContext.TestDeploymentDir, "EdmDiagnose.msl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.csdl", Path.Combine(TestContext.TestDeploymentDir, "Model1.csdl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.ssdl", Path.Combine(TestContext.TestDeploymentDir, "Model1.ssdl"));
File.Copy(@"D:\vsts_test\ConsoleApplicationTest\ConsoleApplicationTest\bin\Debug\Model1.msl", Path.Combine(TestContext.TestDeploymentDir, "Model1.msl"));
string connectionString = s.ToEdmConnectionString(typeof(EdmEncounter), false);
//// Initialize the EntityConnectionStringBuilder.
//EntityConnectionStringBuilder entityBuilder =
// new EntityConnectionStringBuilder();
////Set the provider name.
//entityBuilder.Provider = s.Provider.Provider;
//// Set the provider-specific connection string.
//entityBuilder.ProviderConnectionString = cn;
//// Set the Metadata location.
//entityBuilder.Metadata = string.Format(@"res://{0}/EdmDiagnose.csdl|res://{0}/EdmDiagnose.ssdl|res://{0}/EdmDiagnose.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//entityBuilder.Metadata = string.Format(@".\Model1.csdl|.\Model1.ssdl|.\Model1.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//connectionString = entityBuilder.ToString();
////using (Entities edm = new Entities(connectionString))
//// foreach (var item in edm.ENCOUNTERs.Take(10))
//// Console.WriteLine("{0}\t{1}", item.ENCOUNTERID, item.DISPLAYNAME);
//entityBuilder.Metadata = string.Format(@"res://*/EdmDiagnose.csdl|.\EdmDiagnose.ssdl|.\EdmDiagnose.msl", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
//entityBuilder.Metadata = string.Format(@"res://{0}/", "DataModel.Cis.Oracle, Version=3.0.0.0, Culture=neutral, PublicKeyToken=null");
connectionString = s.ToEdmConnectionString(typeof(EdmFeeInfo), false);
try
//using (TransactionScope tx = new TransactionScope())
using (TransactionScope scope = new TransactionScope(TransactionScopeOption.Required, new TimeSpan(0, 0, 30)))
//using (var dbcn = s.Provider.CreateConnect(connectionString))
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
//edm.Connection.CheckOpen();
//using (edm.Connection.BeginTransaction())
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
item.Amount = item.Amount * -1;
edm.SaveChanges();
// using (EdmFeeInfo edm2 = new EdmFeeInfo(connectionString))
// edm2.Connection.CheckOpen();
// edm2.Connection.EnlistTransaction(Transaction.Current);
// foreach (var item in edm2.FeeInfos.Take(100))
// item.Amount = item.Amount * -1;
// edm2.SaveChanges();
// throw new NotImplementedException();
TestContext.WriteLine("-----------1---------------");
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
throw new NotImplementedException();
catch (Exception ex)
TestContext.WriteLine((ex.InnerException ?? ex).Message);
TestContext.WriteLine("-------------2-------------");
using (EdmFeeInfo edm = new EdmFeeInfo(connectionString))
foreach (var item in edm.FeeInfos.Take(100))
TestContext.WriteLine("{0}\t{1}", item.EncounterId, item.Amount);
6. the test results are as follows:
4 125
4 835.45
4 3458
4 2350
4 200
4 100
4 300
4 123
4 234
无法列入分布式事务处理（Could not be included in the Distributed Transaction）
-------------2-------------
4 125
4 835.45
4 3458
4 2350
4 200
4 100
4 300
4 123
The main error message:无法列入分布式事务处理（Could not be included in the Distributed Transaction） , not use distributed transaction everything is normal.
My test environment MS DTC and Oracle MTS Recovery Service run on the same computer, but OracleMTSRecoveryService registry values under£º HKEY_LOCAL_MACHINE \ SOFTWARE \ Wow6432Node \ ORACLE \ OracleMTSRecoveryService ,not under HKEY_LOCAL_MACHINE \ SOFTWARE \ ORACLE,I do not know that there is no relationship.
Is not configured incorrectly?Who can help me, thank you very much!

Do you really have a requirement to push data from Oracle to Access rather than pulling data from Oracle to Access? It would be exceptionally unusual to push data from Oracle to Access.
Pushing from Oracle to Access would means that you want some Oracle process running that is updating Access. But you said that your Access database was on your "local desktop" which implies that it is not running on a server where it is always available. So that means that the Oracle process is going to regularly encounter (and report) errors because the Access database is not available. In turn, that's going to mean that your push process is either going to cause the underlying transaction to fail or it's going to mean that the push process is going to have to implement a fair amount of code to queue data to be pushed at a later date (and track all those changes) which is no small task. None of that seems particularly pleasant.
On the other hand, Access is designed to pull data from real relational databases like Oracle. That's the far more normal approach architecturally. It doesn't require an Oracle process, it doesn't generate errors on the Oracle database when the local desktop is down, etc.
And, of course, I'm assuming that introducing Access is even architecturally reasonable. Most organizations would be extremely hesitant to allow data from an Oracle database to get moved into Access because that quickly means that they lose control of the data from a security standpoint, that there are now multiple copies of the data floating around when changes & corrections are made, etc. That causes all sorts of headaches normally above and beyond the headaches that pushing from Oracle to Access would create.
Justin

If using timed access to shut down a device at 11:00 pm, if currently online will it automatically shut down?

Similar Messages

Maybe you are looking for