Im getting tree bings on a grey screen after the latest update

is any one else having this problem?

Hi, not quite sure what tree bings is?
Do you mean 3 beeps?
Can you count the beeps or flashes?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.

Similar Messages

Why won't the window show on the screen after the latest update?

When I try to open Firefox, it shows that it has a window open in the taskbar, but it will not show up on my screen.
== This happened ==
Every time Firefox opened
== I installed the newest update ==
== User Agent ==
Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_6_2; en-us) AppleWebKit/531.21.8 (KHTML, like Gecko) Version/4.0.4 Safari/531.21.10

Hello J. M.
Hopefully this support article is what you need:
https://support.mozilla.com/en-US/kb/Firefox+will+not+start

After the latest updat to Mavericks 10.9.3, my imac continues to loop back to the login screen...Suggestions??? THANK YOU VERY MUCH!

After the latest updat to Mavericks 10.9.3, my imac continues to loop back to the login screen...Suggestions??? THANK YOU VERY MUCH!

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the request of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[45]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}')printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ s/ *:$//;x;s/\n//;/Apple|Capacity:|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;};/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;} ' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/:/;END { if(NR<100)print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}')print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR==2'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' ' s/^.{52}//;s/ .+//p ' ' /Launch[AD].+\.plist$/;END{if(NR<100)print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/;END{if(NR<100)print "/System/"};' '/^\/usr\/lib\/.+dylib$/p' '/\/etc\/(auto_m|hosts[^.]|peri)/s/^\.\/[^/]+//p' ' /\/(Contents\/.+\/Contents|Frameworks)\//d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' /lR/ { if($2<='${p[25]}')print $2;} ' ' BEGIN { FS=":";} $3~/(sh|ng|ic)$/ { n=split($3,a,".");sub(/_2[01].+/,"",$3);b=b"\n"$2" "$3" "a[n]" "$1;c=c$1;} END { d="sort|tail -n'${p[38]}'";print b|d;close(d);if(c)print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(A.+ E.+ text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' /:/{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status "-F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL'" '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/*/*.{BS,Bas,Es,OSXU,Rem}*.bom' '{/,}L*/Lo*/Diag* -type f \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;' '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto_master,{cron,fs}tab,hosts,{launchd,sysctl}.conf} /usr/local/etc/periodic/*/* .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP RSSI Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear;};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ test "$v"&&echo "$_";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;A0;{ A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D22 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D23 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;D22 32 31 43 38;D23 20 42 32 41;D23 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

After the latest update when I try to turn on my computer I get this error: panic(cpu 1 caller 0xffffff80039bd555)

Here is a picture I took of the screen. It happened right after the latest update. Anyone have any idea why or what I can do?

Try a Safe Boot OS X: What is Safe Boot, Safe Mode? - Apple Support be patient as it may take awhile. If you can get started in Safe Mode copy and paste the panic report in this thread Mac OS X: How to log a kernel panic - Apple Support

My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError P1 : c000009c P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError P1 : c000009c P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

After the latest update, all my apple products reverted to an old icloud account. As it no longer exists, I cannot get into it to delete it and add the correct id. How can I change this, especially on my Macbook pro?

After the latest update, all my apple products reverted to an old icloud account. As it no longer exists, I cannot get into it to delete it and add the correct id. How can I change this, especially on my Macbook pro? There is no p/w related to it and even though I tried to reset "password" it won't allow as the id does not exist, neither does the email associated with the old id. How do I switch it to a newer id?

It's all rather odd because the old account cannot 'no longer exist' - if you don't have the correct password you won't be able to get into it, but you can't actually delete an iCloud account from the server.
I'm afraid you will need the services of iCloud Support. If you currently happen to have AppleCare, either because you recently bought Apple hardware or have paid to extend the inititial period, you can contact them here:
http://www.apple.com/support/icloud/contact/
You will need the serial number of the covered hardware.
If you are not covered by AppleCare, then - in common with other free email services - there is no free support and you may be asked to pay a fee.

After the latest update printing off the web has moved from readable to font size 6. How to I get back to font size 10 or 12? hp psc 2210 all-in-one?

When I print coupons or e-mail from my hp psc 2210 all-in-one the font has changed to 6 where before it was size 10 or 12. I have made no changes in my printer settings nor any other changes that I am aware of. This happened after the latest update of Firefox.

I have a carriage jam on my HP Officejet 5510 which I cannot correct.. I have tried everything I know to do. There are two black pieces that will not spring down when the cartridges travel across. I th en get a carriage jam message.
Do these pieces need lubricated?
How can I get t hem to go down when the carriage goes across?
Thanks for any information or help options
Karol

I think there is a very annoying bug after the latest update of firefox, can I talk to someone, or chat with someone so I can get rid of it

Since the latest auto update of my firefox browser I am experiencing strange issues. Every evening when I stop working, I close my browser (closing all the tabs that I am working on and in the morning, I restore the session) . For many years everything worked just fine ... untill after the last auto update of the firefox browser .. all of a sudden a got 302 errors ( a blank page with the description 302 and I believe "page moved here" or something to that extend ... i try to click the link and get nowhere.
I first noticed it on a few wordpress pages (backend ) that I was working on and which were restored from the previous day ...
thinking it was a server error, since we have several vps and dedicated servers .. i contacted the company who hosts our servers ..
they looked into it and apparently .. there were no issues on the server side and neither on that particular computer ... but our server hosts told us .. that it is probably browser related and seemed to have something to with a bug with the cache of the browser
we didn't know what to do .. it was very annoying .. but at that point it only happened once on a hew pages .. so we decided to see what happened the next time
Next time we did not restore a session with wordpress pages .. but with the google search engine open and on a few other tabs logged into social media .... and as was saidn by our server hosts it was indeed not related to work that we did on pages on our servers ... since that time even the google search engine homepage ... showed us ... moved here
Can you pease look into it and fix this .. we are doing the same thing as many years on the same computer also a few years .. so it is not anything we do wrong either .. it is most definitely browser related
so can you please fix it asap .. since when we work on wordpress .. that is not the only thing that goes wrong .. we also have difficulty uploading updates ... when updating sometimes after the update of any particular change on a wordpress page is done ... we are also redirected to a blank page .. so the updated page does not want to load ... in that case we have use our back button ...
which sends us back to the right page ... but with the old data on it ... then we have to refresh that page .. and only then we see the page updated ... so it seems that there is an issue in both direction with the caching of the browser after the last update
Kind regards,
Robert

uninstalled firefox ....deleted all files still remaining under mozilla firefox directory in program files ... to avoid having to reprogram all my settings, reisntall all addons as well .. I did not remove anything from mozilla firefox that is stored in either appdata or under the windows users directory (if any)
... the as suggested reinstalled the latest version of the firefox browser using the link you provided in the email ..; tested and several issues still remain present and unresolved ....
so please this is urgent or I will have to jump browsers and start using chrome .. because we work 14 hours a day 6 (sometimes 7) days a week, to get ready for the launch of our newest venture and we cannot lose that much days on browser related issues ... so please instead of putting me through week long step process .. of do this .. do that .. can you please actually look into the issue from your end .. I use firefox for so many, many years thta I deserve this kind of support .. thnx Robert

After the latest update I can no longer see my iPhone listed on the left column - how do you get to where you can pick

After the latest itunes update I can no longer see my iPhone listed on the left column. How can I get to the section where I can pick & choose apps etc to be synced?
Also I had to get a new iPhone & so I backed up the night before to the cloud & my computer. When I tried to restore from back up with the new phone my back up wasn't there - shouldn't it be automatic via wifi from the cloud?
What am I doing wrong?

Your iphone is shown at the top of the page.
You can also simply click View>Show Sidebar and it will look about the same as it did before.

Iphone4 having problems syncing music after the latest update. only half of my music has been synced. during the syncing process the system stalls and i get an error stating itunes cannot locate the file.

My IPhone 4 is experiencing an issue since the latest update. Itunes will not allow the library to sync my entire library. Itunes get stalled and the error message reads ITunes can't find the file for a certain song.

I had the same issue and was told it was because I was using Windows XP. Not sure if the same issue or not, but check that first.

HT201272 some of my apps are not on my home screen after the ios6 update... how do I get them back?

so i had a number of apps on my homescreen and after the update they disappered. So I go to the app store to re-download them but all it gives me is the option to open them. can someone help me get my apps back, without having to go through 8 processes to access them. thanks

go to settings>general>reset>reset home screen layout and see if they appear.

MacBook hanging on grey screen after SMC Firmware Update

Hi, I'd be very grateful if someone could offer some help with my current problem.
I have a black macBook to which this morning, I applied the SMC update. After restart, I heard a chime and the grey screen came up - all good so far......
.....except 20 minutes later, the grey Apple screen (with rotating progress thing) is still there, awaiting the lovely blue screen which just doesn't want to appear for whatever reason.
Tried resetting PMU, zapping PRAM with no joy.
Any help gratefully received.
iMac 20inch Rev. B and Black MacBook Mac OS X (10.4.7)

I had the same thing happen to me while updating my girlfriends macbook last night..
I started off by booting my 17" mbp via firewire from her machine, and repairing disk / permissions.. didnt work, I tried booting her HD from my MBP and it spun forever too. did the PMU reset and Pram too ( 3 times ), no change..
Solution: Archive and Install and then re-patched everything...
the macbook works now and the SMC firmware installed perfectly this time.

I am using a mac book pro with Leopard OS. when I switch my laptop on it flashes a grey folder with a question mark on a grey screen, after the chime. I have tried all the things mentioned in another discussion. none of those have helped. HELP! im scared.

what must i do? im a student and dont have backup for my work. Im in desperate need of a solution where i wont lose my work from my desktop.

You need to purchase Leopard if you don't have the DVD and reinstall OS X:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

The top of my iPod touch screen is darker than the rest of my screen after the newest update?

So today I turned on my iPod touch (5th generation) and it said there was a software update available. I updated it with no problem, but after the update I noticed almost half of my screen was darker than the rest at the top. (Posting screenshots below) I don't know if it's supposed to be like that because of the update or not. Also, I have a little blue dot (assuming it's a 'dead' or 'stuck' pixel) on my screen that was there when I bought the ipod BRAND NEW on February 13th of this year and I'd like to know if that may be affecting it? Any help would be appreciated!
The darker top screen:
Using apps and Safari the screen is normal:

Hi iBridgetx3,
You can try several things:
1. Go to Settings>Wallpapers & Brightness, and turn the Brightness up or down
2. Go to Settings>General>Accessibility>Increase Contrast, and play with the three options available there - I turned off Reduce Transparency, and turned on Darken Colors and Reduce White Point, because I like the color gradation on the wallpaper on my Home screen. But if you don't like it, then make sure Darken Colors is off, and try that with Reduce White Point both off and on to see what you like best
There are a lot of new settings specifically designed to address the variety of problems that people were having with the initial iOS 7 "look". Play around with them. You will probably find a combination that will suit you.
Cheers,
GB

MBP 15" boots to grey screen after today's update

I have a 2-year-old MBP 15" running Mac OS X 10.7. It's been running without issue, though it gets heavy use so I do routine maintenance on it (every couple of weeks, I boot into recovery and run disk/permission repair, as well as running the rebuild function in TechTool Pro). The main partition is encrypted with FileVault 2.
Today, midway through routine activities, the keyboard and trackpad stopped responding. I forced a shutdown and rebooted. Now, the computer will boot to the FileVault password screen and accept the password, but after that the screen will stay a solid grey with a mouse cursor. The cursor can move around the screen without any hiccups, but of course there's nothing to click on. If I press any keys on the keyboard, nothing happens for the first 4-5 keypresses, but for additional keys the computer gives an error beep with each press.
I can force a shutdown and boot from another partition without trouble, and have run disk/permission repairs multiple times on the main partition, to no avail. I also reset the NVRAM and SMC multiple times.
The only OS/software changes made recently were updates from Apple itself, via Software Update, for iTunes and SSL and one other thing (I can't recall right now).
Any thoughts?

Indeed, restoring from backup was the only workable solution. I had hoped to avoid that, as it is a long, overnight process, but I couldn't find any files or caches or any other trigger that the Finder was tripping on.
I am practically religious about backups, as I have had serious data losses in the distant past. I'm very thankful for Time Machine in situations like this.

Im getting tree bings on a grey screen after the latest update

Similar Messages

Maybe you are looking for