Im using macbook pro ,my version is mac os x 10.4.11 and i cant update anything. how can i update my mac,plzzzz i need a quick answer.
im using macbook pro ,my version is mac os x 10.4.11 and i cant update anything. how can i update my mac,plzzzz i need a quick answer.
check that your current Mac meets the System Requirements for Snow Leopard...
Snow Leopard Specs:
http://support.apple.com/kb/SP575
If it does... then you need to Purchase the Snow Leopard Disc and Install it.
Mac OS X 10.6 Snow Leopard
Would Also Recommend that you do a Bootable Clone Backup of your current Hard Drive Before attempting any Major Upgrade...
By far the easiest way to make a Backup, is to use something like
SuperDuper http://www.shirt-pocket.com/
or CCC http://www.bombich.com/
Similar Messages
-
I have recently purchased a hybred 750GbHDD as an upgrade for my MAC Book Pro (Intell Version) I have a boot camp partition to the original 500GB HDD. How can I expand both partitions to fit the new drive?
I have tried bootcamp and have had no luck due to the fact that boot camp doesn't see the additional HDD space of 250Gb. What am I not doing?Ouch, well there is a problem.
This is the stack of partitions on your old drive
EFI (hidden)
Lion (50GB say)
Bootcamp (50GB say)
Lion Recovery Partiton (hidden)
This is the same stack on your new drive imaged from the old one.
EFI (hidden)
Lion (50GB say)
Bootcamp (50GB say)
Lion Recovery Partiton (hidden)
Emtpy Space (100GB say)
This is what you want
EFI (hidden)
Lion (100GB say)
Bootcamp (100GB say)
Lion Recovery Partiton (hidden)
EFI has to be at the top of the drive and Lion Recovery has to be at the bottom of the drive.
And you only have four partitions.
You can't move the Lion Recovery Partition or Bootcamp partiton, however you can expand the Lion Partition into empty space below it. (but can't delete or move the Lion Recovery partition)
Your Duplicator duplicated perfectly, too perfectly Likely would work with same sized drives/partitions.
This is what your going to need to do.
You need to move the Bootcamp partition to a blank external drive using WinClone and disconnect. This is so you have two backups of it. (one on your old 500GB drive)
You will need a drive enclousre or IDE/SATA to USB adapter cable for the older 500GB drive and option key boot from it. (some enclosures can't be booted from so check first Other World Computing is good place to ask)
Download the free Carbon Copy Cloner, grab any new files off the new 750GB internal drive to the old 500GB your booted from.
Open Apple's Disk Utility and Erase with Zero option the entire internal 750GB drive and let it rip, this will map off as many bad sectors and improve reliability.
Now use Carbon Copy Cloner to clone the 500GB Lion + Lion Recovery Partitions to the internal 750GB, it will "fix" things and place Lion Recovery at the bottom of the drive where it belongs, give all the extra space to OS X Lion.
Next your going to have to follow WinClones instructions to restore your Bootcamp, likely you will have to recreate the Bootcamp partition first (in Bootcamp) to the size you want and then clone. Likely Winclone may "fix" Windows to recognize it's in a new larger partition now. I don't know you'll have to check as I haven't used it.
When Bootcamp creates the partition it will place it near the bottom next to the Lion Recovery Partition.
As you know you will have to re-validate Windows with Lord Redmond or it expires as you changed the hardware. -
I cannot view folders and files in finder on macbook pro OS version 10.9.5. Why it happens and what should I do about it?
Please post a screenshot that shows what you mean. Be careful not to include any private information.
Start a reply to this message. Drag the image file into the editing window to upload it. You can also include text in the reply. -
My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
on my macbook pro the hard drive icon is not on my desktop and I don't know how to find the hard drive or get the icon back on my desktop
Click on the Desktop. From the Finder menu select Preferences. Check the boxes for what you want on your Desktop. If they are already checked, then try unchecking and rechecking.
-
I have an 1 phoe 3gs and need to download newer version of IOS but when n settings , general - there is no Software Update option - how can i update to a leter version of IOS ?
THANKSUpdate it from iTunes on a computer as described at the bottom of this article; devices running an iOS version prior to 5.0 can't be updated straight from the device. It will be updated to the newest iOS release supported by the device’s hardware.
The maximum iOS version for the fourth generation iPod touch and iPhone 3GS is 6.1.3.
(92514) -
Every time I restart my mac air some applications like calendar and Microsoft word automatically starts, how can I stop such applications from starting when ever I restart my mac?
One thing to check: when shutting down or restarting, there is a checkbox in the shutdown/restart dialog which asks whether you want currently open applications to open at startup.
charlie -
Hi, I already installed photoshop trial version and three weeks later I paid on-line for 300 Baht for buy it but it still ask me to join and pay for it. How can I update it in my log in account. Please help.?
You do not buy Photoshop for 300 baht, you are renting it for that much a month. You set up an account with a valid credit card and to see if it is active, you go here. https://www.adobe.com/account/my-products-services.html Look under my Subscriptions.
If all is good, then with the same Adobe ID/password, select "License this Product" and sign in, or Help > Sign in.
That will license it.
Gene -
I have a new apple MacBook Pro. All my music is on my old computer and my i-pad. What is the easiest way to transfer my music onto my new
computer?apps
If you have an iPod touch or iPhone with iOS 4 or later software, or an iPad, you can use iTunes to transfer files between your computer and an app on your device that supports file sharing.
You might want to do this if, for example, you want to save files you create on your device to your computer, or take files with you so you can use them when you’re away from your computer.
You don’t need to sync your device to transfer files, but your device needs to be connected to your computer.
For information about supported apps, see the documentation for your apps.
Hide
To transfer files from your iPod touch, iPhone, or iPad to your computer:
Connect your iPod touch, iPhone, or iPad to your computer.
In iTunes, select your device (below Devices), and click the Apps button.
Below File Sharing, from the list on the left, select the app on your device that you want to transfer a file from.
From the list on the right, select the file you want to transfer, and click “Save to.”
In the window that appears, select the destination where you want to save the file, and click Choose.
The file is saved to the selected destination on your computer.
SImport music and video already on your computer
If you have audio or video files on your computer, you can import them into iTunes so that they appear in your iTunes library.
Hide
Here are ways to add items from your computer to your iTunes library:
Drag a file or folder from the Finder to the iTunes window.
If you add a folder, all the files it contains are added to your library.
In iTunes, choose File > “Add to Library,” locate a file or folder, and then click Choose.
By default, iTunes places a copy of each audio file in the iTunes folder (Home/Music); the original file remains in the current location. For information about adding an alias to the file (instead of creating a copy), see Add items to your library without copying them to your iTunes folder. -
I am unable to update my I Phone 4s through I-Tunes. I believe its due to my antiquated 10.4 operating system on my 2005 I Mac. How can I perform the software update. Currently even the phone function will not work . I'm a novice with this device.
Whatever version of Leopard you purchase, I suggest updating it to 10.5.8 which should have everything you require. To update Leopard download and install Mac OS X 10.5.8 Combo Update. Alternatively, open Software Update and install all the recommended updates. That will include the above updater.
To update your phone:
Upgrading iOS
1. How to update your iPhone, iPad, or iPod Touch
2. iPhone Support
3. iPod Touch Support
4. iPad Support
a. Updating Your iOS to Version 6.0.x from iOS 5
Tap Settings > General > Software Update
If an update is available there will be an active Update button. If you are current,
then you will see a gray screen with a message saying your are up to date.
b. If you are still using iOS 4 — Updating your device to iOS 5 or later.
c. Resolving update problems
1. iOS - Unable to update or restore
2. iOS- Resolving update and restore alert messages -
when i plug my phone into the mac i can see all of my mobile apps on an immitation of my iphone screen, how can i keep these apps in my itunes libraby on my mac as only a few are showing?
Ensure that you computer is authorized for all Apple IDs used to purchase the apps i(n iTunes Store>Authorize This Computer), then connect your phone to your computer, open iTunes and go to File>Devices>Transfer Purchases.
-
"Software update failed", how can I update to ios8 without using itunes?
I've received and error message, "software update failed". How do I update my iphone 5s to ios8 without using itunes?
Wait until later when the servers are quite so busy.
-
looking to connect macbook to television. used to connect easily until i presented PPT for class. now "arrangement" tab no longer displayed, and macbook display does not show on TV
Use Finder and search for 'Microsoft Word'. If it shows up, launch it from Finder and when it appears in Dock, right click the icon and select Options > Keep in dock.
If finder does not find Word it has somehow been deleted. -
What do I do when I power up the computer and get a grey screen with a folder icon and a question mark?
vickyfromosseo wrote:
What do I do when I power up the computer and get a grey screen with a folder icon and a question mark?
Read this: A flashing question mark or globe appears when you start your Mac -
I have an Imac G5 power PC MAC OS X 10.5.8 and want to install firefox, how can I do it?
'''
'''Firefox 3.6.x is the last available from Mozilla for PPC Macs. <br />
http://www.mozilla.com/en-US/firefox/all-older.html
https://support.mozilla.com/en-US/kb/Installing+Firefox+on+Mac
For older Macs that aren't supported in Firefox 4+ versions, try TenFourFox for PowerPC's running Mac 10.4.11 & 10.5.8 . <br />
http://www.floodgap.com/software/tenfourfox/<br />
http://tenfourfox.blogspot.com/ <br />
https://code.google.com/p/tenfourfox/wiki/PluginsNoLongerSupported
Maybe you are looking for
-
Problem with date and timezone
Hello, I am encountering a problem with the command new java.util.date() on a hpux 11 machine. The "date" from command line returns: Tue Oct 26 18:02:02 MEST 2004 And the date from java returns: Tue Oct 26 17:02:02 GMT+01:00 2004 It is as if the JVM
-
How can I read the executed processes std out into my program?
In MyProgram.c I am doing CreateProcess("GetData.exe" ....);. GetData when run on a command line prints about 100 lines of data to stdout. When I run my MyPragrame.exe I want that data not going to stdout instead I want it to be saved say in a buff
-
How do I burn a CD in iTunes 11?
I just downloaded iTunes 11 on my Windows 7 PC and am a little frustrated. I can't figure out how to burn my iTunes music to CD's! I need CD's because my car only has a CD player and doesn't have a 3.5mm cable connection or USB connection for my iP
-
File Sharing from 10.3 to 10.4
Word is on the BigBox running 10.4. On the OldBox running 10.3 system are Word documents. Now there are two problems 1) minor, 2) aggravating. 1) Is that on OldBox pulling down the Go menu; Connect to Server.... the BigBox is listed, but selecting it
-
Trying to sync Ipad with iphone
hey guys, just purchased the new ipad and trying to sync my iphone4S, have used icloud to do this, but missing from the content on the ipad are the messages and photos and cannot seem to transfer them from my iphone...any suggestions?...be good to he