IMac and External DAC Interface Issues

I have a Musical Fidelity M1DAC. When I connect it to my iMac via USB I'm getting distortion that sounds like tape hiss. Has anyone had similar problems using the iMac with a DAC?

I should also add that this has been happening over both ethernet and wifi, so I don't think it is a specific connection issue.

Similar Messages

Macbook Pro and external monitor sleep issues.

I recently upgraded to a new 13 inch MacBook Pro to replace my previous one. With the upgrade, I'm now on the latest OS and I have a Thunderbolt instead of Mini-displayport output. I have a Dell U2410 monitor which has worked great up until now, but I now have the following behavior:
When the laptop sleeps (or puts the display to sleep) the monitor begins to turn on and off. It goes to powersave mode and immediately wakes up, realizes there's no signal, and goes back to powersave mode, etc etc etc.
When I wake the computer up from sleep, the monitor's behavior stays the same. The laptop never detects the display and begins sending a signal.
If I unplug and replug the adapter, all is well.
There seem to be two separate issues: whatever signal the computer continues to send down the display cable after sleep seems to confuse my monitor, secondly, the computer never again sends a real video signal down the line after it wakes up.
I'm on the latest 10.8.3. My adapter is the same adapter I have been using for years, an apple mini-display port to DVI adapter. Supposedly this adapter is still compatible with the Thunderbolt port.
I've seen lots of issues online about wake up issues with the latest OS. Is there a workaround for this yet or do I have to uplug my monitor anytime I sleep the computer?

Hi Steve,
I have had the exact same issues after adding a WD Thunderbolt Duo external drive to a Mid 2011 iMac and then daisy chaining the Dell U2410 monitor off that.
My Mini DP to DVI cable ceased working properly - sleeps issues.
After buying one of these adapters of Ebay:
http://www.ebay.com.au/itm/3-in-1-Mini-Displayport-to-HDMI-with-audio-DVI-DP-ada pter-3in1-convertor-Macbook-/110861703462?pt=US_Audio_Cables_Adapters&hash=item1 9cfdf5926
I then tried all the different cables that came originally with the Dell U2410 with that adapter, and none of then would put the U2410 to sleep properly. The backlight would stay on, or "No Displayport Cable" would float around the Dell display with the backlighting still on. Or otherwise the Dell would try to go to sleep and then wake up again and cycle like you found.
Apples Mini DP to VGA adapter was sleep successful with the VGA cable (Analogue) but the output picture was not as sharp as DVI or Displayport, plus there was RF interference with the cable.
After lots of internet searching I have found a near perfect solution:
A HDMI to DVI cable with the HDMI end connected to the Ebay 3 in 1 adapter, which then connects to the Thunderbolt port.
Connect this to DVI-D 1 on the Dell U2410.
On the Dell in Menu - Other Settings, disable DDC/CI
Now in OSX Settings - energy Saver you will have to tick:
"Put Hard Disks to sleep where possible" and select a short time frame for "Computer Sleep"
I have found that the display would go black but the backlighting on the Dell U2410 would stay on, when the display went to sleep on the Mac as per the Energy Saver "Display Sleep" setting.
The backlighting on the Dell would only turn off when the time for 'Computer Sleep" has elapsed and the external Thunderbolt hard disk went to sleep as well.
The Dell U2410 would then wake up correctly as well when my iMac woke, with this setup.
Cheapest solution for you would be to try an Apple or Ebay HDMI to DVI adapter and then use the DVI - DVI cable that came with the Dell.
If that fails get the 3 in one Adapter and use my Mini DP/Thunderbolt to Ebay Adapter to DVI-DVI cable setup.
I'm assuming your new Macbook Pro comes with the HDMI port ?
I believe the Sleep Issues with this monitor are all related to appropriate signal on the cable, and only the HDMI to DVI solution will work correctly on Mac's connected to the Dell U2410.
Good Luck. :-)

20" iMac and external Dell 24" : doesn't work with Mini DVI to DV adapter!

Help! My lovely Dell HP LP2475w 24" Monitor can't be used as an external monitor. The native screen resolution is 1900x1200 60Hz. The Apple site claims the iMac is capable of being able to output this resolution.
When the HP is plugged in via the apple mini to dvi adapter a (tested) DVI lead, it recognises the monitor, but can't bring it to life. Just an occasional flash. In the resolution listing for the HP, the native resolution 1900x1200 isn't listed.
Plugging a cruddy old 20" Samsung with the same DVI leads works with no problems.
I NEED to use the HP for my Photo editing, and phone calls to Apples support have proved fruitless.
Does anyone have a 20" Intel iMac and an HP LP2475w set up that works?
Many thanks for any help.

I'm glad you got it working!
So do you have it working at full 1900x1200? I've noticed a few more oddities about my iMac on this monitor. First off is that initially I could only go as high as 1680x1050, which I think is the native resolution of the iMac. Now I actually see two more options, one of which being 1920x1200. This surprises me since you couldn't get it to a full 1920. Both resolutions produce the same size image on the HP, but the 1680x1050 is fuzzier. It's odd to me, same dimensions just a little less clear. I can stretch that using the HP's settings to full screen, but I cannot adjust the 1920/1200 image even though there is a black border around it.
Can you tell me what color settings you have on the HP? I have really struggled to find something I like. I actually like how things look in my iMac, and my MBP. I can't get things to look the same on the HP. I also feel like text is just a hair fuzzier on the HP than on either the iMac or MBP. I'm tempted to try a used 23" Apple Cinema Display, but I'm not sure I'll have any better luck with that. I mostly concerned about the image quality when I use my laptop, and for some reason I'm not getting great results with the HP or Dell externals that I've tried.

Transferring files from original imac AND external CD for old imac

I have an original iMac that has tons of files on it I would like to save. I created a LOT of materials when I was teaching and they are all on the old iMac. It also has two games I bought on floppy discs that I would really like to keep. I tried to load files on a Passport, but the iMac won't recognize it. I have two other old iMacs (not quite originals) as well, but they won't take the Passport either. They will both take a flash drive. I can take word processing files (I can't even remember the application at the moment) off the older one and convert them to Apple Works on the other one, then take the converted files to our iMac 9.1 and convert them to Pages. Then I put them on the Passport. It is a pain, but at least it works. I can also save the documents as pdfs and put them directly on the newer iMac and copy and paste in a Pages document.
The original iMac does not lend itself to any of this. What is the best way to transfer files? It seems like a very long time ago I tried to connect it to my newer iMac with an Ethernet cable but it wouldn't accept the cable. If I am remembering correctly I called Apple Support and they said it lacked something that would allow it to connect. I do not remember if I have tried a flash drive on it or not. I believe I did and it would not recognize it.
Also, does anyone know how I can manage to save a copy of the games? Since I bought them on floppies I can't reinstall them if something happens, but I believe it is within the law to make a backup copy. Someone please correct me if I am wrong. I do have an external floppy reader for the original iMac, but it only works on user created floppies, not commercial ones. If I can manage to hook up to a flash drive or another computer and I simply save the game application, will that be enough? Or is it not possible to know until I try? Will saving the application get all the necessary files?
My second question concerns the newer (but still really old) iMacs. My daughter would love to play some of the games she used to play on them, but the CD drives do not work. Does anyone know where I can get an external CD drive that we can attach to these old iMacs so she can enjoy her games? The computers work fine; she just can't insert the CDs, because it's next to impossible to get them out again.
I believe on the "newer" two we are running OS 9, at least on one of them. I do not recall the OS on the original, but it is whatever it came with. OS 8, perhaps? It has been probably half a year since we fired it up.
I appreciate any advice and help anyone can give me. We really like these old iMacs, which is why we still have three of them. If we can save the files off the original iMac, we would still keep it so we could play our two old games from time to time. :-) I would part with one of the other old iMacs, but I really need to get the files first, and since it won't take a Passport I'm wondering if I'm stuck putting files a few at a time on a flash drive. Do you think it would take an ethernet cable? It seems like I tried to connect to my newer iMac but I couldn't get the computers to recognize each other. I followed all the steps for sharing, but I still couldn't get it to work.
Thank you so much.

Have you formatted the Western Digital Passport drive as a Mac OS Extended (HFS+) volume, or is it factory-formatted for PCs? If the oldest iMac is only running OS 8, it can't recognize HFS+ volumes. It was OS 8.1 that introduced that feature. Additionally, the version of the USB support files (which is somewhat OS-dependent) on the iMacs hard drives affects what will or will not be recognized by those older computers. With each successive release of the USB Adapter Support, the database of supported devices was broadened. The easiest way to transfer the contents of the iMac's hard drive is to physically remove it from the computer and connect a USB-to-IDE adapter directly to it. These adapters come with an external power supply to provide the 12 & 5 volts needed to power the drive. The data connection block is designed to fit either a 3.5" hard drive or the smaller 2.5" laptop drive, as well as newer drives that connect via SATA. It has an included USB cable that connects to a standard USB port, enabling direct reading/writing/file transfers from the hard drive to the computer to which it's connected. These adapters are not Mac-specific in terms of design, so you can buy one at a PC store and use it. For the purpose of identifying such an adapter, here's one that's often recommended in these Forums, carried by Other World Computing. As I mentioned, this adapter is not platform-specific, so you can buy/use a less expensive one sold by PCs stores. I bought one for $15 from Micro Center (PC store), and it has worked with Macs and PCs. As for removing the hard drive from the old iMac - and I assume that it's one of the original models with a tray-loading optical drive (as opposed to the slightly newer ones that have a slot-loading optical drive), you can find directions for accomplishing that if you do a web search. The link that I had for one site (that was good for years) is no longer valid. The iMacs that have a problem ejecting disks are undoubtedly slot-loading models. There are two wide rubber rollers inside those optical drives that grip the disk to pull it in or feed it out. Over time, the rubber dries out, causing the rollers to lose their natural gripping capabilities. If those iMacs have a FireWire port on the side, I'd suggest an external FireWire optical drive. Today, the only type you'll find is a DVD±RW drive, which is more than you need for your intended purpose. A basic CD-ROM drive isn't manufactured/sold anymore. Other World Computing has a few FireWire optical drives, but their least expensive model sells for about $100. Obviously, that costs more than the value of the entire iMac at this point, but the drive will also have USB connectivity as well. You may find other uses for it with your other computers (Macs & PCs), especially if they don't have a CD-R, CD-RW, DVD-ROM, or DVD±RW drive. As for transferring a program itself, there could be other associated files. You'd want to check the Extensions and Control Panels folders for any that are named to likely indicate being a part of the program's installed files. The Preferences folder will probably have a file that has saved game settings, but a new one would be created when you run the program in another supported computer. Depending on the age of the program - and you indicated that it was on floppy disks - its compatibility with newer, pre-OS X releases might be limited. The external USB floppy drive that you use with the older iMac should read commercial floppy disks, but it will not recognize the older 800K (Double-Density) Mac-formatted floppy disks. They're disks that typically format as 720K floppies in a PC, but the variable-speed FDD in older Power Macs was able to fit an extra 80K of data onto those disks. A standard 720K "PC" floppy disk should be read by that drive, but it can't recognize an 800K "Mac" disk. A 720K/800K Double-Density floppy disk only has the slide-lock hole at one corner, while a High-Density (1.44 MB) floppy disk has an additional hole at the opposite corner to differentiate it from the older type.

24" iMac and 3GB RAM limit issues

I have a legitimate concern with the 24" iMac and wanted to know if anyone else thinks it's an issue. Read Apple's tech note on late model 2006 iMacs including the new 24" model.
http://developer.apple.com/documentation/HardwareDrivers/Conceptual/HWTechRAM/Articles/RAM_implementation.html#//apple_ref/doc/uid/TP40003899-DontLinkElem entID5
In order to use RAM in an interleaved fashion it states you must use matched pairs. Meaning same size and type. SO.....if the new iMacs will take a 2GB SO-DIMM then why won't it register 4GB total? You can configure your new iMac with 3GB of RAM but it won't be interleaved. On top of that 2GB SO-DIMMs are super expensive in the +$700 range. More then MacPro's FB-DIMMs.
I don't see anyone talking about this but it seems to be a legitimate concern.

That IS the point, what person paying $2000 for a computer would be willing to pay another $1500 for a 4GB RAM upgrade? I just think right now it's hurting Apple's sales of the 24". The 24" encroaches on the prosumer market and at this point in time an affordable 2GB of RAM may seem adequate now but most likely not in 6 years. Which is how long I had my Digital Audio Power Mac. So I think anyone in the prosumer market NOW, like myself, looking for a machine that will last a few years may look away from the 24" and steer toward the Mac Pros. My needs fall squarely in between the 24" iMac and Mac Pros but unfortunately my budget does not. I could live with the 24" even with the expensive cost of the 2GB SODIMMs. I would in fact wait until the prices fell. What I can't live with is the fact that the iMac will only ever be able to use an uninterleaved 3GB when the possibility of an interleaved 4GB seems to be there. I was only able to keep the Digital Audio because I squeezed every ounce of life I could out of it because of various periodic upgrades.
Reluctantly I'm going with the Mac Pro but I REALLY wanted to get the 24" iMac. Thats all.

IMac and Macbook Pro Networking Issue

Just recently both of my Macs have developed a wierd networking issue. I am sharing folders on my Windows server (WHS), now this odd slow issue appeared when using a file from the server. It acts like my network is really slow when opening a file, but my windows machines work fine on it.
I have not made any changes to the server, I am running a Gigabit Cisco network (not linksys) in my home and this thing has got me stumped. I installed an anti-virus on the iMac and it found nothing. Either wired or Wireless I see the same results but only related to the Mac's..... does anyone have an idea what might be doing this? I am kinda a Mac noob in most aspects so I am looking for any help here.

It very well could be the antivirus app, most are intrusive and debilitate rather than enhance performance and should be removed using the developers instructions. You haven't really told us anything useful such as any settting you may have changed. However if you began working backwards resetting any changes and uninstalling the apps added since the performance issue started then you probably will find your issue.

Airport Time Capsule and external hard drive issue

I have an external hard drive connected to my 3TB airport time capsule. It no longer shows up in the finder sidebar on my iMac, which is connected via ethernet. It does appear on my Macbook Pro, connected via Wi Fi. It worked normally when first set up. I no longer have a way to drag files from my iMack to the hard drive so I can share them with my MacBook Pro. I am running Mavericks.

This is crude but if you need a work around, just plug the USB drive directly into the iMac.. copy the files to it.. then plug it into the TC.
You also do not need to use the TC as an intermediary between your iMac and MBP.. just turn on sharing in the computer.. so you can directly copy files from one to the other.. Macs have public access directory preconfigured for each user account.
As far as mounting the TC..
In finder use Go, Connect to server.. and type.
AFP://TCname or TCipaddress
Where TCname is the actual name of the TC.. I strongly recommend you follow SMB network rules.. ie if your TC has a name like
Fred Blog's Time Capsule 2445566.
It is too long.. it has spaces and it has non-alphanumeric characters.
Shorten it to FredTC
No spaces no characters that are NOT alphanumeric.
TCIPaddress is simply the standard IP.
You can also use CIFS://TCname which according to the article forces the connection back to SMB1 rather than SMB2 which as usual is broken.
But I would definitely use AFP if possible. I cannot understand the decision to move to SMB as standard.

I have installed mackeeper on my iMac and ia show 1945 issues, is subscibing to mackeeper the only way to get rid of these issues

I have installed Mackeeper on my iMac an it shows 1945 issues, and they have used 700+ GB of hard drive space, is subscribing to Mackeeper the only way to get rid of these issues?

Those are not real issues. I tested the MacKeeper trial on a freshly-installed OS X 10.8.2 system, with absolutely nothing added to it, and it identified almost as many "junk files." They're not really junk, you're being scammed to convince you to pay the money to buy the program so you can "fix" the "problem." There have been many reports that allowing MacKeeper to "clean up" your system can actually destroy it, requiring reinstallation.
MacKeeper is to be avoided at all cost. For more information, see Beware MacKeeper. Remove it according to the instructions here:
http://applehelpwriter.com/2011/09/21/how-to-uninstall-mackeeper-malware/

Please Help - Time Capsule and External hard drive Issues

Recently, I switched from Comcast to AT&T uverse as my internet provider and I started experiencing problems.
(1) I have a 4th generation Apple Time Capsule which I am using as my router.
(2) Connected to the Apple Time Capsule - USB - is an external hard drive (not for backup with Time Machine.)
(3) I have a 2011 Macbook pro which I use to access my file on my time capsule and external hard drive.
(4) I had been using my AT&T portable Hotspot from my cell phone to get internet access on my MacBook pro from remote locations to gain access to my external hard drive which is attached to the time capsule.
(5) On August 2, 2014, I switched from Comcast to AT&T and had the AT&T turn off the router function. (I have been using the router from my apple time capsule)
(6) Under Network I switched to bridge mode.
(7) And since August 2, 2014 my time capsule has not been backup.
THE PROBLEM - I need to be able to use the hotspot function from my cell phone to gain access on the external hard drive using my MacBook Pro which I was able to do before. Now it is showing time capsule under finder but unable to connect.
Do I need to reset my Time Capsule since I have a new service provider. Everything else works fine - meaning able to get internet signal but unable to access my external hard drive and backup my time capsule. Please HELP.

(5) On August 2, 2014, I switched from Comcast to AT&T and had the AT&T turn off the router function. (I have been using the router from my apple time capsule)
(6) Under Network I switched to bridge mode.
(7) And since August 2, 2014 my time capsule has not been backup.
If you got ATT to turn off router function in their modem..
Then 6. is wrong.. You cannot have the Network switched to bridge mode..
You must have it set to dhcp and nat.
That is also why you cannot backup.. the TC is off the network.
Please change back to router mode in the TC.
Ensure the internet tab shows dhcp and you create a wireless network.
Then power down the TC... power down the ATT modem.. wait about 20min (you can try 5min.. but it might not be long enough).
Power up the ATT modem.. wait 2min for things to flash lights in de right blinkin order.. then start the TC.
Open the airport utility and make sure your TC captured the public IP and is now working as the router.
That should fix that end of it.. the hotspot end??
Tell us what happens.

Imac and external webcam

Hi all,
I have a G5 with an external isight.
I'm getting a new iMac soon.
My questions is...in my business the external cam is handy in that I can move it
anywhere. If I need to show a client a tool I'm working on I can do so.
With an iMac I have to move the whole computer around.
Soo for those times I need the flexibility of an external....
1. Is it possible?
2. How would I go about doing it if it is
3. Since this external iSight is starting to work when it wants to...
whats a good 3rd party web cam to use? I know there are none close to an iSight but...
Thanks in advance

Plenty of folks report using the FireWire external iSights with no real issues. Some have had issues with the microphone, but there is a fix for that, I think in the Mac mini Apple Discussions.
I have also seen folks recommend this one; http://ecamm.com/mac/imagewebcam/
Sometimes with USB webcams on iMacs with built in iSight cams, you have to fool the Mac to use the external cam. The Mac defaults to the internal, so you have to occupy the internal with another app, then open the app you want to use and the external should be available to choose. After choosing you shut down the other app.
Dah•veed

Imac and external hdd

im trying to boot from external hdd and efi bios does not even see the external hard drive!!!!
i work at the educational facility and i just got 40 imacs that have to be cloned!!!
doing every one of those by hand would be a nightmare.
does apple actually provide any tools except netboot and netinstall that would help me with the quest?
any tricks i have to do on the mack to recognize external drive as a boot drive?

A good source for how to do netinstalls is www.bombich.com.
You fail to tell us anything about this external drive, how it's formatted, what's installed on it, etc. The general rundown is:
You need to partition the external drive using the GUID partition scheme. If the external drive has never been formatted before then format the drive Mac OS Extended (Journaled.) This should be done using the OS X Installer Disk One that came with the computers. If the computers are all the exact same model then you only need use one of the installer discs. However, if you have different hardware, then each different model has a different build of OS X. You will need two different external drives or you will have to update the system on the external drive to one that will be common for all the models you have (this would be 10.4.8 (Intel).
Here's the procedure:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. Then select Disk Utility from the Installer menu (Utilities menu for Tiger.)
2. After DU loads select your external drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Click on the Option button and select the GUID partition map and click on OK. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
After formatting is completed quit DU and return to the installer. Now quit the installer. The computer will reboot. After reboot clone the system on the iMac to the external drive:
How to Clone Using Restore Option of Disk Utility
1. Open Disk Utility from the Utilities folder.
2. Select the backup or destination volume from the left side list.
3. Click on the Erase tab in the DU main window. Set the format type to Mac OS Extended (journaled, if available) and click on the Erase button. This step can be skipped if the destination has already been freshly erased.
4. Click on the Restore tab in the DU main window.
5. Select the backup or destination volume from the left side list and drag it to the Destination entry field.
6. Select the startup or source volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
8. Select the destination drive on the Desktop and press COMMAND-I to open the Get Info window. At the bottom in the Ownership and Permissions section be sure the box labeled "Ignore Permissions on this Volume" is unchecked. Verify the settings for Ownership and Permissions as follows: Owner=system with read/write; Group=admin with read/write; Other with read-only. If they are not correct then reset them.
For added precaution you can boot into safe mode before doing the clone.
Why reward points?(Quoted from Discussions Terms of Use.)
The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

24" Core Duo iMacs and external Firewire disks

Hi guys,
I'm having a bit of an issue with the new iMac that I picked up yesterday. There seems to be an issue with mounting disk devices connected to the Firewire 400 port. Disk devices mount fine off the Firewire 800 port. The bizarre thing is that I plugged an old iSight camera into the Firewire 400 port and it works fine. This seems to eliminate both the possibility that the Firewire controller is faulty and that the FW 400 port is dead.
Just to remove the possibility that it could be a crappy driver, I installed XP via bootcamp but I get exactly the same issue. (although windows is a little more specific. It actually detects the name of the disk device but says it cannot be started)
I've zapped the PRAM and left the machine dormant and unplugged for 30 mins to no avail. Could someone plug a disk device into their FW400 port and see if they get the same issue i.e. nothing happens? (card reader, laptop in FW target mode, external HDD)
I'll take the machine back if I have to but I really loathe the though of lugging this thing back to the Apple store.
Thanks.
Danny

I also am having trouble.
I cannot mount my eMac in target disk mode. The only way I could get the eMac drive to mount was if I put a firewire disk in line with the eMac. i.e. a firewire cable from the eMac to the disk and another cable from the disk to the iMac. (Same model 24" 2.4GHz aluminum).
I thought the issue was with my eMac, but when I went to connect my Canon CanoScan 9950F scanner the iMac would not see it unless I also went through the firewire drive.
I have since learned that the drive does not have to be on and spun up, but it has to bridge the connection. The drive I'm using is model PHR-100AF Macally 3.5" enclosure.
I have been able to mount this drive without having to chain it through anything else. I've also been able to mount a Macally PHR-250CC 2.5" enclusure and a el cheapo 3.5" enclosure that uses the Prolific PL-3507 chip. Also, my 3rd generation iPod mounts just fine.
I don't have anything for the FW800 port so all my experiences are with the FW400 port.
My question is:
Is there something wrong with my iMac that it cannot mount my eMac in target disk mode without being chained to another external drive?
Is there something wrong with my beautiful, new 24" aluminum 2.4GHz Intel Core 2 Duo imac that it cannot connect to my Canon CanoScan 9950F scanned?
I expect more from Apple. I expect that it should at least work with their own hardware (the eMac).
Should I go back to the Apple Store and complain?
Thanks,
Chris
p.s. I guess I should ask my own question huh?
Message was edited by: ctopher

IMac and External Monitor

I have an early 2006 iMac 20" core duo 2.0ghz 2GB Ram.
I already have an external 17" monitor plugged in with the mini dvi adapter.
I have recently purchased a 32" Samsung TV, which has PC Input. This will be arriving shortly.
Is there any way for me to connect both the TV and the external monitor to the iMac? I would rather mirror the display to the TV and extend the desktop onto the 17" monitor.
If there is a way to output to both, but by a different way - i.e. not mirroring and displaying - this would be great.
I didn't know whether it was possible for me to use some sort of splitter. So a mini dvi to 2 vga's. Then vga to tv and monitor.
Thanks for the help.

Hey Stephen
You might want to check out [DisplayLink|http://www.displaylink.com>
This Google Search: [multiple displays with intel imac|http://www.google.com/custom?q=multiple+displays%20with%20intel%20imac&sa= Search&client=pub-6263300333013957&forid=1&ie=ISO-8859-1&oe=ISO-8859-1&cof=GALT: %23008000;GL:1;DIV:%23336699;VLC:663399;AH:center;BGC:FFFFFF;LBGC:336699;ALC:000 0FF;LC:0000FF;T:000000;GFNT:0000FF;GIMP:0000FF;FORID:1;&hl=en]
And these from [MacWorld|http://www.macworld.co.uk/mac/news/index.cfm?newsid=20862] and [Cambridge|http://www.cambridgenetwork.co.uk/news/article/default.aspx?objid=43 026]
Dennis

ITunes 6 and External Hard Drive issue. Please Help!!

Hi Gang!
I'm having problems when using iTunes 6 to work with my external HD as my iTunes Music library vault.
Under iTunes Advanced section I have set my Preference to change my music library from my iMac G5 to my external HD. Everything works fine, but everytime I restart my computer, iTunes automaticaly sets the Preferences back to the Music Library folder in the iMac G5 instead of the the external HD. I never had this problem before with other versions of iTunes.
Am I missing something or is there an extra step I should take to having iTunes accept the external HD as my permanent iTunes Music Library holder?
Thanks for any input.
Alex

Hi TP2GO!!!
Thanks for your reply!! You mention that this problem is being caused due to the fact that my external HD is not available at start up. But the driver is always available, since it is always hooked up to my iMac at all times. I've noticed, though, that iTunes starts up at login and maybe system is running it before it runs my external HD (if I follow your logic), possibly causing iTunes to set the iTunes library back to default since it cannot find the external driver where the new library should rest. So, my new question is: how do I disable iTunes from running at start up to try and see if this is what's causing my problem?
Thanks very much indeed for your input!!!!
Alex

1st Gen Time Capsule and External Hard Drive Issues

I have a 1st generation Time Capsule and have never had any luck connecting an external hard drive (both Western Digital MyBook and Seagate FreeAgent Pro) via an USB hub for an extended period. They will connect for a few hours or up to a day or two before they lose the connection and look up the wi-fi connection (although the internet and connected printer don't seem affected). Thought it might be an issue with the powered hub, but have same issue with both (Belkin and APC). I have read that others have had similar issues.
For laughs, I connected a dinky personal drive (WD My Passpoert 750gb) to the USB hub and it came up instantly and had no issues for the 12+ hours it was connected. Question #1: can I run a portable drive for an extended period of time (weeks, months, years) via USB hub without killing it?
Also, I would like to house my large iTunes and iPhoto libraries to be accessed by 3 different MacBooks. Question #2: is a NAS drive connected directly via ethernet to the TC is the best answer?
I am spoiled by the simplicity of the plug-and-play connectivity of Apple products. Is there a mysterious sequence of procedures that I need to follow to get the Time Capsule to play well with the USB connected HDs?
Thanks in advance for your help.

To answer the general question, a drive that is constantly spinning is both more likely to be damaged and less likely to give issues of access to the USB.. the one fights the other. Feel the small passport drive and see if it is continually spinning.. if so that could account for it maintaining connection.. although according to your testing 12hrs is not long enough to know for sure. Feel the other drives. If they spin down and then when you try to access them, do they spin up? Or is it the spin down time that dictates the time they are available on the network. It may simply be a case of usb connected to a router is not getting the correct spin up info.
IMHO a NAS is the right way to do this.. especially if you have multiple computers accessing it. USB is not a fast connection. Especially hanging off the TC series 1, were not renowned for speed. A NAS is not that expensive now and using a mirrored raid you at least have some protection. Remember to always have the source files in mulitple locations. A NAS can also work as an itunes server, which the TC cannot. And the connection from gigabit ethernet to sata is not made via usb.
As a secondary option.. open your series 1 TC and put in a 2TB hdd.. this is well documented.. larger sizes give trouble but the series one can easily be updated to 2TB.. remember also the power supply in a series one can go at any moment. Get ready for it, plan for it.. one day it will happen.

IMac and External DAC Interface Issues

Similar Messages

Maybe you are looking for