IMac and M-Audio firewire solo

Hi everyone!
I've recently bought an M-Audio firewire solo interface, installed the last certificated driver, shut down the system as recommended, plug in the interface and turn on again the system. Unfotunately Mac OSX doesn't recognize the interface.. I've tried it on my mac book pro and it does work perfectly, and the firewire 800 port on my iMac seems to work, cause I take my iMac to the assistance and they try a firewire hard disk that worked without problem.
Now my question is: how can i fixed this problem? does anyone suggest me to fotmat and reinstalling the OS or maybe try to install an update of the firmware? the iMac is new, bought on March of this year..
Thanks for your help, and sorry for my english!!
---Marco

The easiest way would probably be to put a pair of 6 pin to 4 pin adaptors (of opposite "genders") into the cable run, or to use a 6 pin to 4 pin cable with a single 4 to 6 pin adaptor on the end of it, vivajam. THis should cut the power supply from the Mac to the device.
http://www.granitedigital.com/catalog/pg20_firewiregenderadapters.htm seem to have the sort of thying you would need.
Cheers
Rod

Similar Messages

Gb2 and m-audio firewire solo...rec. volume very low.

Dear all,
i'm using an m-audio fwire solo device with shure sm-58 mic.
Still, I see that record levels are always very low in gb regardless of how close i can get the mic to the amp or else.
Im pretty shure it has something to do with gb..
all settings are fine
any help?

Garageband defaults to the built-in mic. Make sure that the built-in is not actually being used. Open Garageband preferences, click on the Audio tab and select your device.
In addition, I have noticed that devices work better if they are connected before turning on your computer.
kurt

Help with recording guitar on GarageBand using M-Audio Firewire Solo

Hello everyone. I hope someone can help me. I recently bought a new mac mini and M-Audio Firewire Solo to record music. I'm new at recording so I have no idea what to do.
The problem is when I record playing the guitar, the sound is so low, I can barely hear the guitar playing when I play it back. I turned the gain to maximum level and I still can barely hear the guitar record. I know it's recording because I can hear the guitar when I play the record back, but the sound is way too low.
The weird thing is that the microphone works fine and when I record vocals, I can hear the playback fine.
Did I miss anything? Is there a good setting for recording guitars using M-Audio Firewire Solo? Is it because M-Audio Firewire Solo is not compatible with the latest Mac Mini system?
Please help! Thank you!

I connect the guitar to the guitar input that is in front of M-Audio firewire solo using this cable: http://www.livewire-usa.com/products/products.cfm?sBrand=adv . Then I turn gain up to the maximum level.
When I play the guitar, you know the bar that goes green on garageband (not sure what it's called)? Even if I strum really hard, the green never goes up past 1/4 of the bar. When I'm using the mic and speak a bit loudly, I can see that bar turning red. So it seems like it's not reading the input properly, but really I'm not sure, so hopefully you'll be able to help me
I'm actually using the mac mini's speaker to hear the sound, so I'm not sure if it's only coming from one speaker or not.
Sorry if I miss any important detail. I'm a newbie. And as always, I appreciate you taking the time to answer my questions!

"Line 6 TonePort UX2" vs "M-Audio FireWire Solo" vs "FIREPOD" with GB3

Hello Folks,
I just purchased GarageBand 3 and I want to get some hardware to be able to play and record my songs with good recording quality. I will be using my voice, a guitar, GaragaBand 3, and a music keyboard.
Has any of the PRO's here tried the "Line 6 TonePort UX2" and "M-Audio FireWire Solo"? They cost about the same.
I am also looking at the PreSonus FIREPOD.
1. What are the pros and cons of each with GB3?
2. Which one will allow me to make good quality recording of my voice and instruments?
Any comments and/or recommendations?
Thank you in advance for your time.
Cheers!

Your FireWire drive didn't stop working because of an OS upgrade. It may have died, but the OS change didn't "Stop supporting it" (I have 8 FireWire drives online, all the time, 2 of which are from about 6 years ago)
Everyone's needs are different, so only you can make the final decision, but like Schneb said, those are probably all good choices.
From my readings here I shy away from M-Audio because their driver updates have lagged behind OS updates. They DO update them, but sometimes people have been stuck because they updated their System without checking if there were new drivers yet, and then found they weren't available yet.
My opinion (IOW, if I were buying right now) would be one of the PreSonus products, neither of which require drivers (though the Inspire does have a software control panel, this is not necessary for the operation of the interface itself)
Once that decision was made, it would be a time to figure out future needs. If you think you might like to be able to record 8 tracks at a time, hands down, the FirePod would be my choice. If not, then the Inspire would be a fine choice.

M-audio firewire solo and it's unresponsive friend Garageband3

I recently purchased the m-audio firewire solo so I could do multitrack recording. Here is the problem I am trying to troubleshoot: I have gotten the SOLO to work input & output, I just can't get GB3 to respond/record. These are the steps I've taken to get around this problem: downloaded updated driver/installed driver, change preferences I/O, turned computer off then back on. Any insight?? Someone please help. Thanks

Alright so I am back in the forum. So the firewire solo work briefly a week ago. I tried to do some recording tonight and my macbook did not recognize the unit. I uninstalled all the M-audio software/drivers, then reinstalled all software and drivers (including the most recent driver). Still nothing. Check everything in the GB3 preferences and the system preferences....
Is anyone else experiencing this? I have only been able to find a handful of forum/troubleshooting posts all outside of the apple supported sites that make a brief mention that this product might not work with the recent Mac drivers and M-audio is dragging their feet.
Anybody got any thoughts? I am trying to make a decision about returning this product and finding something else... so whoever replies if there is something else comparable either USB or firewire in the $200 range, please let me know. I appreciate all the input.

M-Audio Firewire Solo+Leopard = problems?

After 6 months of a battling with my iMac, different systems and different drivers. The final replay from M-Audio is this:
This is a known issue with all FW800 Macs (apart from the 1st two G4 tower
systems) when using firewire audio or video devices as Apple has placed the
FW800 and FW400 connections on the same fierwire bus.
In order to run these together you would need to add a PCI, PCMCIA or
Expresscard interface depending on your Mac which will add an extra firewire
bus and allow these devices to function well together.
Regards
Richard
UK Tech Support
M Audio UK
www.m-audio.com
The problem I get is that every time I tried to use my M-Audio Firewire Solo, the screen goes grey and the power logo comes in the middle with a message asking to switch off the computer from the power bottom
And at that is the only thing to do because is completely frizzed at this time.
I got me a Protools MP to run it with the sound card.I was so happy then, but here I am still wondering.
I have as well an iBook G4 that i had used with Panther and M-Audio FW Solo, and all was fine then. When I upgraded the system to Tiger, is when all the problems started. Now with Leopard it will do the same as in the iMac, won't have it.
Does anyone have the same problem or a little bit of advice?
Thank you
Thank you

hey, firstly, your not the only one going through this, since the last 10.4.10 update, heaps of us musicians have notice fatal errors with the update, mainly, the mac not recognising our devices that were once working fine, but now with the update that are not being recognised by the mac.. check out the other threads and make a complaint to apple:
http://discussions.apple.com/message.jspa?messageID=4967716#4967716
http://discussions.apple.com/thread.jspa?messageID=4884775&#4884775

Getting Soundtrack Pro to record with M-Audio Firewire Solo?

I'm having trouble trying to record 'live' into Soundtrack Pro. I've got a mic into analog mixer into M-Audio Firewire Solo audio interface into ibook set up.
In STP, I can select firewire channels 1 to 2 (under "Recording" tab) for the input device but nothing is recording when I hit the record button. the mic>mixer bit is working fine. I'm quite certain the mixer>audio bit is working so I think its a problem with compatibility between the M-Audio Firewire Solo device and Soundtrack Pro software....although it shows up as an option in the select audio input/output settings in STP... I've also got the latest Tiger driver for the Firewire Solo device and the latest update for STP.
I CAN record from the in-built mic on the ibook so that bit works...
Currently, I've been recording individual tracks into Audacity then exporting them all as separate tracks into Soundtrack Pro for post production as AIFF files (drag and drop them into STP in the order I require). I'm doing this as a temporary measure until I can find out how to get M-Audio Firewire Solo talking to Soundtrack Pro.
Anyone got any ideas?

Well, I got it working with Soundtrack Pro and Audio Hijack Pro in the end. It seems that only the front side of M-Audio FireWire Solo recording interface actually seems to work and only the right channel (mono). Its a little bit annoying but it works...not sure why the back ones did not work (s/pdif, balanced and unbalanced phone jacks plugs), perhaps its something to do with the fact that the front has gain level knobs and the back doesn't....hmm...maybe not enough power to drive the back connectors?
Anyway, if any of you happen to use M-Audio FireWire audio interfaces (analog to digital converter) and you face a similar problem, then its probably going to be a similar thing...

Is M-Audio FireWire Solo ok for Logic 9 ?

Is M-Audio FireWire Solo ok for Logic 9 ?

Yes. All M Audio interfaces work very well with Macs running Lion and Logic Pro 9. It all just depends on what specs you're looking for in an interface. Assuming the FireWire solo meeting your demands in terms of sample rate, bit depth, and ins and outs, go for it!!
Cheers,
Electrik

M-Audio FireWire Solo - appropriate for what I need? Compatible with FCP?

Hey all:
I'm shooting a video short next week with a DVX100. Eventually I'll need to do some voice over work in my... "studio." I have mics but need a preamp. The M-Audio Firewire Solo fits the budget comfortably. My minimum requirements are one XLR input and Phantom Power, which it has.
I'm just wondering if anyone has advice against the decision. I have very little experience with audio interfaces. Anything I should be watching out for? Any other suggestions? My budget tops out at $400US or so, but I don't want to overdo it, either. I'm not looking for something that will perform things I may need in the future, I just need a quality, compatible, reliable preamp.
Thanks in advance, everyone.
Michael

I teach in a school that uses Tapco Mix60 mixers (http://www.tapcoworld.com, approx $60) with FCP with great success. So much so, I bought one for use at home with my rig.
True, the whole path is analog. But using the speaker/microphone jacks on the back of a G5 work well. So far with about 30 students using the systems we have had no problems. Just buy some Hosa cables (Mini to 1/4” Phone Stereo Breakout) from your favorite supplier to connect the Mac to the mixer. Add a microphone and you are all set.
As a side note, I generally use Soundtrack Pro to record voice overs. It seems a little easier and I have access tools to make me, or talent, sound better.

Suggestions between m-audio firewire solo versus tascam us-122?

I'm new to audio recording and garageband, and am looking to get into it for messing around to make decent sounding voice-overs and home studio music to integrate into my final cut projects.
Any suggestions between the two of these interfaces?
m-audio firewire solo
tascam us-122
(maybe even the m-audio fasttrack or mobile pre...although I don't mind spending a bit more for the above models instead)
I'll probably be buying either the mxl v67 condenser mic or the m-audio Nova to go along with it...mainly for vocals.
Thanks guys!

I think all of these are good audio interfaces, judging from what people tell about it. To throw in another alternative: If you're fine with two inputs, the Presonus Inspire is a good bargain at around 200 dollars.

Recording mono tracks with m-audio firewire solo

I am having a devil of a time recording tracks (both xlr mic and 1/4" guitar input) to right and left channel...when I unclick stereo setting on track recording I don't get a level.
After I have recorded a voice or instrument in one channel I can't copy the track and bounce it to the other channel using the pan...what can I do? Is it the firewire solo that is messing this up or am I missing a setting?
I just want to be able to record mono voiceovers and guitar tracks in left and right channels in with soundtrack loops using a firewire audio interface.
Thanks...
middle school video teacher going crazy in dc...
Mac OS X (10.4.8)

My problem is pretty much the same except that I can get it to work with my microphone (which is channel 1).
(M-Audio Firewire solo)
From the recording tab I select firewire solo multichannel as the input) and i UN click stereo.
When using the microphone (channel 1) it works - I get a mono recording on a given track.
When I use the guitar (channel 2) it does not work.
(Note that, if I select stereo and play the guitar it works, but only records in one stereo channel and I want it to just record mono).
(Also note that I can get it to work in garage band where, for inputs you have the options of 1/2 stereo, 3/4 stereo, 1 mono, 2 mono, 3 mono, or 4 mono - all I have to do is select 2 mono and I can record from the guitar using mono).
So the problem is that I can get sound track pro to record from channel 1 mono, but not channel 2 since I can't find any setting, similar to garage band, where I can specify which channel to get the mono signal from and, I guess, by default it does it from channel 2.
I've been struggling with this and combing the web for ever and can't seem to find an answer for how to change this simple setting.
Help!

Very Faint Signal from Mic Running thru M-Audio Firewire Solo

I get a very faint signal running a condenser mic thru M-Audio Firewire Solo to GB. 1/4 guitar input in Solo records fine. Solo is selected as input in system preferences. All gain and recording levels are maxed. Any ideas?

It's a tube mic so it has its own power source/brick. I've tested the mic with just its power source and its working great.

M Audio firewire solo with yosemite - 'The previously selected audio interface is not available'.

Hi, I recently bought a new mac mini with yosemite OS. I plugged in my M-audio firewire solo and (after a bit of trouble) finally managed to see it appear in GB. then moments later a dialogue box appears with 'The previously selected audio interface is not available'.
There doesn't appear to be any update drivers from M-Audio and the CD that came with the interface also does not work?
I can't find any information with this problem. Can any one help?

Oops. . . A loose lead connection may have been the problem, although still not receiving a signal?

M-Audio Firewire Solo - Electric Guitar

I am connecting via the M-Audio FireWire Solo, but I can't get garageband to recognize my electric guitar to use the amp modeling and effects. The only way I can get my guitar to be recognized is by adding a real instrument track(not electric guitar), but this limits the sounds i can produce.
With the real instrument track I get options of the input(1/2 stero, 1-4 Mono, etc.) I don't get that option via the electric guitar track.
Any suggestions on how i can utilize the electric guitar amp modeling and effects in garage band and use the m-audio device?

In a electric guitar track double click on the amp or click the edit button it will spin around and you can select the input channel.

Anyone using M-Audio FireWire Solo for iChat audio output?

Audio output for iChat works perfectly through my G5 internal speaker but does not work through my FireWire Solo. It yields 100% digital distortion everytime the person on the other end speaks. Everything else in my setup works beautifully with my M-Audio device (Logic, Pro Tools, Reason, iTunes and all other applications).

You have landed in iSight Discussions. You may find better help in the Expanding your Power Mac G5 Discussions or iChat AV 3 Discussions area.
I do not use M-Audio or any of the other things you post about except iChat AV, and iChat AV does NOT work through my DP G5's internal speaker.
I offer the following possibilities for your consideration if you cannot find better help:
(0) When using iSight or iChat AV, you may be experiencing Possible hardware or software conflicts. This link gives tips for investigating that possibility.
(1) You may be trying to use M-Audio FireWire Solo for other than its intended purpose. The web site states, in part: The FireWire Solo is designed from the ground up as an easy-to-use, high-quality interface for songwriters to record guitars, vocals and more on the computer.Perhaps your M-Audio's documentation or the "Support" information linked on the web site can help you determine whether your device is compatible with iChat AV and your other AV equipment.

IMac and M-Audio firewire solo

Similar Messages

Maybe you are looking for