IMac DV SE 2000 - Screen malfunction, probably analog board failure.

After almost a decade of trouble-free operation, my iMac DV SE is manifesting issues of analog board failure. I can now only start it up properly once in a few tries. By this, I mean that the machine itself starts up, but the screen fails to turn on. What I have noticed is that when the screen does not turn on, the machine does not make the "electrical discharge" sound that all CRT computer monitors make when you turn them on. On the occasion that the screen does turn on, the sound is audible. I am not sure (not being an engineer) whether this is a noise from capacitor discharge or what, but I suspect that some component is failing inside. If that is the case, any recommendations other than "check eBay" as to where to find parts, and what part is most likely responsible?

I'm no fan of eBay either. This outfit is in Eugene Oregon, and one of their techs is a frequent contributor to these hallow halls:
http://www.synaptech.com/catalog/index.php?mainpage=index&cPath=16_18
PAV boards are not cheap. No one is making new ones and, as the older G3's eat their origianl boards, the supply of workable used boards declines.
Our 400 DV is also suffering. Ours tend to do thermal shutdowns after a few minutes of running.

Similar Messages

IMac Screen Malfunction

I have a 24" iMac which I bought in late 2008 and tonight the screen malfunctioned... has anyone seen this before and is there a solution?

amybish wrote:
I'm in Sacramento... also, I adusted the screen calibration about a week or so ago - do you think that might have contributed to this?
Doubtful. Well in the Sacramento area you have 2 Apple Stores available and several AASPs to choose from. Get your quote, then you can decide what to do from there.

My imac has a gray screen and spinning wheel and will not start up

my imac has a gray screen with a spinning wheel but will not start what does this mean?

Probably a damaged or failed HD. Please read Gray screen appears during startup on how to troubleshoot and what to do.

My iMac has a black screen when I turn it on.

When I tune on my mac it goes straight to a black screen. What do I do to fix this?

You are posting this in a server/enterprise message board. You might have better lucking posting it somewhere else.
You can try hooking up an external display to your iMac to see if it's a problem with the iMac screen or the logic board. If you get an external display picture, then you probably have a display problem in your iMac (bad lcd, bad back light, bad power to display, etc).
Also, try unplugging your computer from the electricity, holding down the power button for 15 seconds, and then plugging it in again. This resets the power management system, just in case something got buggy.
Good luck!

Just bought a new iMac, I am in screen saver mode and have forgotten the password ?

Just bought a new iMac, I am in screen saver mode and have forgotten the password ?

This link will tell you exactly how to reset your password
http://support.apple.com/kb/HT1274
In OS X Lion or later, you can reset your user password with your Apple ID.
In Mac OS X v10.6.8 or earlier, follow these steps to reset a password when there is only one administrator account on the computer, or if the original administrator account needs a password reset. "Original" administrator account refers to the one that was created immediately after installing Mac OS X. If the original administrator password is known, that administrator account may be used to reset the passwords of other administrator accounts using the steps described above. These steps require an optical drive; if your Mac does not have an optical drive and you have a Mac OS X v10.6 Install disc, see below.
Start up from a Mac OS X Install disc (one whose version is closest to the version of Mac OS X installed). Usually, you can start from the disc by putting it in your computer, restarting, and holding the C key. Or, put it in the computer and click the Install or Restore icon you see in the disc's main window (after which the computer will start from the disc without you needing to hold C). Or, you can use Startup Manager or the Startup Disk preference pane to select the Install disc.
Choose a language, click the arrow button to continue,
Mac OS X v10.6 or later: Choose Password Reset from the Utilities menu.
Mac OS X v10.5 or v10.4: Choose Reset Password from the Utilities menu.
Mac OS X v10.3: Choose Reset Password from the Installer menu.
Tip: If you don't see this menu or menu choice, you're probably not started from the disc yet.
Note: The default keyboard layout is U.S. English while started from the installation disc. If you use a keyboard layout other than U.S English, use the Input menu (the flag icon on the right side of the menu bar) to select the desired layout before typing a new password.
Select your Mac OS X hard disk volume.
Select the user name of your original administrator account.
Important: Do not select "System Administrator (root)". This is actually the root user. You should not confuse it with a normal administrator account.
Enter a new password.
Click Save.
Click the red button in the upper left corner to quit the application.
Choose Quit Mac OS X Installer... from the Mac OS X Installer menu.
Click Restart.
After following these steps, you'll want to also follow the steps in this article.
Mac OS X v10.6: Resetting the original administrator account password on a Mac that has no optical drive
These steps require a second computer that has an optical drive.Note: If the second computer is a Mac, make sure Mac OS X v10.5.3 or later is installed. If the second computer is a PC, make sure the DVD or CD Sharing Update 1.0 for Windows is installed.
Open "Remote Install Mac OS X" from the Utilities folder.
Follow the onscreen instructions.
For more information, see Sharing DVDs or CDs with Remote Disc.

How do I use an external Monitor to access files on my iMac with a broken screen?

I have an 20 inch desktop iMac with a broken screen. It is the files on the computer that I wish to recover, after that, I can be on my merry way. Unfortunately, VileVault was on (Not my choice), and for some reason, when I target the disc image of the broken mac with a new one, ONE of the accounts "appears" to be completely empty. All of the accouts were running FileVault, but only one (mine) failed to be transferred because it is "empty". I refuse to believe that my files are actually all gone, because theoretically there should be nothing wrong with the CPU itself, just the screen.
Thus my goal is to use a monitor on my broken screen iMac and simply log in and access my files normally, and perhaps pull them out with a USB or something. I have a DELL monitor, and a DVI (The big hairy plug with screws I think) converter that works with my old iMac, along with the male/male DVI cord. However, when I hook it up, nothing happens. I have tried booting the old CPU while holding F7, and option as I read on a forum, and neither produced results.
Does anyone have any ideas on how to 1. Get the monitor to simply show what's going on on the mac? or 2. Pull out my files through some other means?
Thank you.

If you have a second Mac computer, you may want to try to copy over as many files you can. One way is to use target disk mode.
http://support.apple.com/kb/HT1661
http://lowendmac.com/misc/06/0710.html
You need to follow this procedure to recovering a filevault id. Mac OS X 10.3, 10.4: FileVault - How to verify or repair a home directory image ... http://support.apple.com/kb/HT2631?viewlocale=en_US
Robert

I have an iMac G5 isight (20" screen) Leopard OS 10.5.8 I do not have an intel chip. I am unable to open movie links on facebook using Adobe flash player. I called Adobe Systems and they said Adobe no longer supported computers that did not have intel chi

I have an iMac G5 (20 inch screen) i sight (no intel chip).Leopard OS 10.5.8. Recently I went on Facebook and tried to open a movie site someone had sent me on Facebook andwhen I tried to open the video on Facebook, I was told I had to upgrade my Adobe Flash Player. i tried to do this, but turns out that Facebook is requiring folks to have an intel chip in order to view movies...this is outrageous! Just think of all the folks in the world who have great running pre intel chip Apple computers. I called the Adobe Help line and was told that I really needed to buy a new computer....no thanks. How do I find a way to get a new version of Adobe for Facebook and youtube. I wish Apple could develop a way to have intel chips installed in the older computers. If you have any suggestions on this please let me know.
Thanks, Sarah

Either get a screen cleaning cloth, or carefully us a slightly damp lint-free cloth and dry off with a dry link-=free cloth.
As to Flash Videos: I am in a similar same boat. I cannot watch flash videos on the BBC website or on BBC iPlayer, although all other flash videos (YouTube and FaceBook for example) are fine.
For reasons that passeth all understanding, they work with the PPC version of Firefox, called TenFourFoxG5.app, once you have anabled plug-ins, as it does not natively support Flash.
You can download TenFourFoxG5 from here:
http://www.floodgap.com/software/tenfourfox/
Now for the intersting bit: TenFourFox, like Firefox, does not support most plug-ins. Unless you are prone to headaches (in which case don't) you can read about that here:
http://code.google.com/p/tenfourfox/wiki/PluginsNoLongerSupported
But there is a workaround!
Open TenFourFox and type in the address bar: about:config (no spaces) and click return. This gives you a warning that it might harm the application. Ignore that and click on 'I'll be careful, I promise' and you get the config file that you can edit - with great care.
Look/search (scroll down) for: tenfourfox.plugins.enabled
Set it to true. (Double click it to toggle it)
Now close TenFourFox, open it again, and Flash will now work, as it now uses the plug-ins that Safari has stored.
I am using Flash 10.1.102.64 in TenFourFox and it works just fine.

My Imac is showing gray screen with red line when booting and restarts again

My Imac is showing gray screen with red line when booting and restart again, I can load it in windows 7 safe mode with red lines across the display, pls help

The graphic card is damaged. You can't do anything more than taking your computer to an Apple Store or reseller and getting your graphic card replaced.
Sometimes, when the graphic card is damaged, operating systems can't start. That's caused because the drivers that make the graphic card work detect an error, telling the operating system that the graphic card is unusable, so the operating system can't start and it restarts. However, you can start in safe mode because operating systems use a basic driver in this startup mode

My iMac has a blank screen with an icon showing a flashing question mark. I have rebooted and still nothing but that on the screen.

My iMac has a blank screen showing an icon with a blinking question mark. I have rebooted and still the same. Any ideas?

Mac OS X: Gray screen appears during startup BTW, iOS info is useless, post machine and OS version specifics.
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2

Apples update didn't work for me: Boot Camp: iMac displays a black screen during installation of Windows 7

Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
I have followed each of the steps listed in the link above with no success.
Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
Any feedback would be greatly appreciated.
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
</unattend>
iMac (27-inch, Late 2009)
2.66 GHz Intel Core i5
16 GB 1067 MHz DDR3
ATI Radeon HD 4850 512 MB

Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

Using iMac (Intel) as second screen.

Is it possible to easily use an older iMac as a second screen to a new MacBook Pro?
This would obviously save the cost of purchasing a new monitor.
Thanks for any advice/instructions/rulings.

Short answer is no. You need a late 2009 or later iMac to use Target Display Mode Target Display Mode: Frequently Asked Questions (FAQ)
There are software work arounds but they may or may not meet your expectations http://www.screenrecycler.com/ScreenRecycler.html

My Kids we on my 24 in iMac. Now the screen is "Zoomed in" and I can get it to go back to nomal for an application/desktop etc. The monitor is set at correct resolution. Help!

My Kids were on my 24 in iMac. Now the screen is "Zoomed in" and I can't get it to go back to normal. Tried resetting resolution, rebooting in safe mode.
Help!
Thanks.

Tap the top of the mouse with two fingers.
To turn off this feature, Un check the "smart Zoom" box

I've stuck with Entourage way too long. Now I don't dare install the Mavericks OS because all my Entourage files will go away. And my iMac won't open Mac Mail (probably because I've never opened it in the 5 - 6 years I've owned the Mac.) Any suggestions?

I've stuck with Entourage way too long. Now I don't dare install the Mavericks OS because all my Entourage files will go away. And my iMac won't open Mac Mail (probably because I've never opened it in the 5 - 6 years I've owned the Mac.) Any suggestions?

If you are wondering why you are not getting any responses, it is because you have vented a complaint without any details that make any sense or give anyone something to work on.
If you want help, I suggest actually detailing what has happened, with versions of software etc. Anything that would let us assist.
As a start I am guessing that you have not really got the hang of "How it all works". Firstly download the Pages09_UserGuide.pdf from under the Help menu. Read that and view the Video Tutorials in the same place. A good addition would be the iWork 09 Missing manual book and something to help you learn how to use your Mac.
If there are specific tasks you need help with:
http://www.freeforum101.com/iworktipsntrick/index.php?mforum=iworktipsntrick
Is a good resource.
Peter

2007 intel based iMac has the white screen of death with the mouse visible?? WHATSUP

My 2007 Intel based IMAC has the white screen of death with the mouse cursor as the only visible item. What is up with this? Is this the equivalent of the windows blue screen of death?
Doug

Read the "More Like This" thread links located at the bottom left of this page.

IMac Freezes Periodically During Screen Saver Only

I own a late-2006 Intel-based iMac. Over the last few months, I've noticed that the iMac freezes when the screen saver is running. This doesn't happen all the time, and it doesn't matter what screen saver I use. (None of the screen savers is a third-party.) The iMac doesn't freeze at any other time.
Any ideas?
- Keith
P.S. I'm running Snow Leopard right now, and it happens even with Snow Leopard, just as it did with plain ol' Leopard.

Your iMac has a dedicated Graphic's chip (GPU), while some of the Late 2006 17" iMacs had a GMA 950 graphics processor with 64MB of DDR2 SDRAM that shared with the main memory. To check which Graphic's chip you have go to: Apple > About This Mac > More Info and in the Hardware section select Graphics/Display.
If you would like to monitor the temperature of your GPU, CPU, HD and Memory check out the iStat Pro widget > http://www.islayer.com/apps/istatpro/
The main reason I suspect the lack of RAM over an overheating GPU is because you only reported a problem with the Screen Saver and not with other intense graphic's like movies, videos or games.
Please let us know how you make out with the RAM upgrade.
Dennis

IMac DV SE 2000 - Screen malfunction, probably analog board failure.

Similar Messages

Maybe you are looking for