Imac g4 dropped off home network, other still good

airport (snow) network with g3 ibook, intel imac and g4 imac. g4 was tuned off for couple days and will now not see home wireless network. airport symbol appears gray and it shows up in system profile, so i think it is functioning. in addition, the other computers, as well as this problematic g4 imac have always picked up 3 or 4 other neighborhood networks. but now this g4 imac will not see any of these other networks when the other 2 computers do.
i have tried the airport admin utilities and network assistant in preferences with not luck. the fact this computer is not seeing any of the networks that the other 2 are picking up makes me think this is a hardware problem ( card, wire). before i take it appart, are there any recommendations. thanks.

airport (snow) network with g3 ibook, intel imac and
g4 imac. g4 was tuned off for couple days and will
now not see home wireless network. airport symbol
appears gray and it shows up in system profile, so i
think it is functioning. in addition, the other
computers, as well as this problematic g4 imac have
always picked up 3 or 4 other neighborhood networks.
but now this g4 imac will not see any of these other
networks when the other 2 computers do.
i have tried the airport admin utilities and network
assistant in preferences with not luck. the fact
this computer is not seeing any of the networks that
the other 2 are picking up makes me think this is a
hardware problem ( card, wire). before i take it
appart, are there any recommendations. thanks.
I also have an airport (snow) network with G3 iBook, intel iMac and G4 iMac. I also have been able to pick up 3 or 4 neighborhood networks with all three computers. After a recent power outage, my G4 was no longer able to see any of the networks (my intel imac and ibook G3) automatically reconnected to my home network. My G4 cannot seem to see the airport. I have run airport admin utilities and network assistant (diagnostics and assist me) with no luck. Can anyone help us?
Thanks.

Similar Messages

  • Officejet 4620 drops off the network after the first operation

    HP 4620 drops off the network soon after one operation is performed. I have to turn it off and on again to bring it on line and then it repeats. The message is " unable to communicate with printer".  I have run all the diognostics and they say your printer is operating normally.  I have down loaded the latest drivers. Running Win 7 (64 bit). My only clue is that I have a new router, Netgear.

    Hi LennieZup
    I understand you can print over the network one time and then you have to turn the printer off and on again to continue to print.
    I will be happy to assist you with this.
    It may not be the printer, it may be your router's inability to wake the printer.
    Disconnect the power cable on the router for 10 seconds, then reconnect the power cable again. You might need to check to see how many devices can be setup on the router at the same time. Depending on each router.
    I would recommend updating the printers firmware. HP Officejet Firmware.
    I have included a document for Printer Does Not Maintain Wireless Connection. Try Step six: Assign your HP product a static IP address.
    If you need more assistance just let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • IMac G4 dropped off network

    Hello,
    I have a home business network set-up where I do my creative work on an iMac G4 and Mac Book and use a cheap box PC as a print server for my wide format and large colour laser printer. The PC, iMac and laser printer are connected to a Lynksys WRT54GS by ethernet and the MacBook to the router via wireless g.
    Everything has been going great with all machines able to see, print and fileshare with each other. The other day, having done nothing special to the machine or new programs loaded, the iMAc convinced itself it is off the network.
    In the Status tab of Network prefs, I am told that an ethernet cable is not connected, yet the MacBook can still mount the User/Computer volume ofthe iMac (but can not see the hard drive as a sharable volume). So the ethernet connection has not failed. Running diagnostics bangs into the "your ethernet cable is not plugged in".
    From the PC side - it can see the MacBook and vice versa but tells me I do not have sufficient permissions or password (whatever) to mount the iMac drive.
    Investigating the entire Network prefs pane, it seems that all settings are normal - IP addresses, etc.
    When I tried to print to the ethernet printer, I was told by the iMac that "Appletalk is not enabled" (it is).
    Any thoughts on this one?
    TIA
    Brian H
    iMac G4 800Mhz and Mac Book 2.0Ghz   Mac OS X (10.4.6)   Lynksys wireless router, Airport Express

    airport (snow) network with g3 ibook, intel imac and
    g4 imac. g4 was tuned off for couple days and will
    now not see home wireless network. airport symbol
    appears gray and it shows up in system profile, so i
    think it is functioning. in addition, the other
    computers, as well as this problematic g4 imac have
    always picked up 3 or 4 other neighborhood networks.
    but now this g4 imac will not see any of these other
    networks when the other 2 computers do.
    i have tried the airport admin utilities and network
    assistant in preferences with not luck. the fact
    this computer is not seeing any of the networks that
    the other 2 are picking up makes me think this is a
    hardware problem ( card, wire). before i take it
    appart, are there any recommendations. thanks.
    I also have an airport (snow) network with G3 iBook, intel iMac and G4 iMac. I also have been able to pick up 3 or 4 neighborhood networks with all three computers. After a recent power outage, my G4 was no longer able to see any of the networks (my intel imac and ibook G3) automatically reconnected to my home network. My G4 cannot seem to see the airport. I have run airport admin utilities and network assistant (diagnostics and assist me) with no luck. Can anyone help us?
    Thanks.

  • My fix for the AE dropping off the network in client mode

    Turn off any encryption.
    I have the linksys/vonage/wireless G router, which supports WPA. The AE will sometimes join the network with WPA but it takes anywhere from 1-5 minutes for it to do so. When finally on the network it shows up on the Airport manager list and in iTunes. The most playtime I could get out of it was 15 mins, before it would drop from the network. The light on the AE would be solid green, but I couldn't ping it. The only solution was to power cycle the AE. Note this is dropping w/out running the microwave, cordless phone, verifying my network channel is different from my neighbors, etc.
    I tried fiddling with WEP but the only way I could get that working was to specify the full key in hex, appearantly Apple and Linksys don't agree on the way to take a passphrase and turn it into a key.
    So I dropped to the unencrypted network, disabled the SSID broadcast and restricted wireless access to my machines. Works great now. :/ If I run the microwave and the cordless phone at the same time I can get Airtunes to drop, but it comes right back when the microwaving is done.
    Very frustrating, and the part that is the most irritatating is that my mac laptop and iMac can get on the network just fine.
    Still deciding if I want to keep it this way or say nevermind and return the AE.

    I found the solution after many many many attemps.
    It's not a MBP problem, it's your wireless router.
    1- Set your BEACON between 20 and 50. D-LINK router for example use 100 has default value. It's too long.
    2- Change your channel. D-link default is 6. Use whatever channel. I use 10.
    Hope you enjoy!

  • Internet constantly dropping off Home Hub 3

    Hi All
    Hoping that someone can assist me as I am about to give up on BT and move to Virgin due to having unuseable Broadband.
    I have had issues for some weeks now and spoke to BT who said there was an issue on the line and then arranged after a long wait of over a week for them to test the line, come out and then fix the issue.  The home hub was dropping off and the orange light would come on .  SInce they have fixed this issue the blue lights are on the home hub but i still have issue with internet constantly cutting out.
    I am using Windows 8 and have my home hub near the TV.
    Basically the itnernet keeps dropping out and when i look the Home Hub connection on windows 8 will show either no connection at all or limited connection.  I then have to reset it or disconnect it and the sign in again and it works again but only for a few minutes.  It can drop off every few minutes so is in effect totally unuseable.
    Any suggestions as to what this may be.
    ADSL settings below: -
    ADSL Line Status
    Connection information
    Line state:
    Connected
    Connection time:
    8 days, 22:37:45
    Downstream:
    1,600 Kbps
    Upstream:
    448 Kbps
      ADSL settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.1 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    10.0 dB / 12.0 dB
    Line attenuation (Down/Up):
    63.0 dB / 31.5 dB
    Output power (Down/Up):
    16.3 dBm / 12.7 dBm
    FEC Events (Down/Up):
    249631 / 1235
    CRC Events (Down/Up):
    5743 / 523
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    Loss of Link (Remote):
    0
    HEC Errors (Down/Up):
    15551 / 461
    Error Seconds (Local/Remote):
    0 / 0

    further away the better but preferably 3 or 4m
    as it is probably your wifi that is dropping and not your internet you can try downloading inssider3 (istumbler if MAC) and then run it. This will show the broadcasting networks round about you and their channels including your own. If you then enter your router and change your wireless channel to a free or less congested channel.
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Why does Apple TV drop off my network and have to be restarted to reappear?

    My Apple TV constantly drops off my Airplay menus on both iMacs, two iPads, and two iPhones.  It will reappear when I restart it, but it will diaper after being activated.  Also, I can't access my home-sharing-enabled computers from the Apple TV menu unless I restart it.  This happens every time I try to use it either to use it for AirPlay or Home Sharing.

    The Apple TV is connected to my network on ethernet. After the Apple TV has restarted it will work for a while until it is either unselected from AirPlay or until after the movie is finished and I have disconnected it from home sharing.  It's just inconvenient to have to restart it every time you want to use it.

  • Is there a better way to share your music library outside your home network other than using an i-Pod classic?

    APPLE-Here's a complement and a question.  Why has the i-Pod Classic fallen from grace compared to other i-Pods?    Please know that while I can share my music using home sharing within my home network with a different i-Tune account, it seems to me that the best benefit of having an i-Pod Classic is that you can give your dedicated music library and device to a friend or housemate to use outside your wireless network (and not on the internet) to use while traveling.   Am I wrong?   Is there a benefit to sharing the cloud usage with a friend.   Add that to the click wheel and I think I'm going to be a fan of the i-Pod Classic far longer than it is in production.  I hope Apple NEVER stops production of this device.   Are you listening Apple?

    Fightthegoodfightnow wrote:
    I also lend books I read and CDs I own and that isn't stealing either. 
    Yes it is, and it's precisely what the music industry has been fighting about for years.
    Interpreting the law to suit yourself does not render law ineffective. Apple's Terms of Use mention this:
    Keep within the Law
    No material may be submitted that is intended to promote or commit an illegal act.
    Do not submit software or descriptions of processes that break or otherwise 'work around' digital rights management software or hardware. This includes conversations about 'ripping' DVDs or working around FairPlay software used on the iTunes Store.
    ...which is why my original response was framed as it was. Nothing to do with "attack mode". (You're the one with an "attack style" user name.)
    Fightthegoodfightnow wrote:
    Heck, as I understand it, I can legally burn up to five copies of a bought song for noncommercial, personal use....so copying in and of itself is also not illegal.
    As I recall, the music industry has acknowledged that making a copy of a CD (that you own, and still have in your possession) is regarded as "Fair Use" - and is therefore tolerated. But until that point was established just a few years ago, then technically, it was illegal to rip a CD into iTunes and onto an iPod. Slightly different to your interpretation. That same music industry (and the musicians) regard the following as unacceptable:
    keeping a copy of a CD but disposing of that CD to someone else
    lending the CD to friends, so that they can make a copy
    making copies and giving them or selling them to someone else
    But what is okay is:
    Home sharing
    use of the CD by someone in your family, living under the same roof
    At this time, if a couple wish to combine their two iTunes accounts of purchased digital music once they get married, they cannot. Perhaps that's where Home Sharing comes in.

  • IPADs and IPhones dropping off wireless network

    I have a site with a number of iphones and ipads that are attaching to a Wireless network managed by a lan controller ( cisco 2504 )
    but they seem to drop off every 16 minutes .... and can then get back on a few minutes later.
    Any ideas appreciated.
    Thanks

    Right now I have it in the setting; "(OFF) Bridge mode". Do you know if the airport extreme if the internet bottle necks will crash?

  • Continually knocked off home network while cable modem looks normal

    I have a cable modem connected to an Airport Extreme base station (circa 2005, so it's the 802.11b/g). Almost every day I get knocked off my home network and the name of the network that shows up is "linksys" for some reason. The cable modem lights continue to flash in their normal sequence. I live in a private house, not an apartment building.
    What I then do is follow a protocol that I discovered on this site (I don't remember if it was this forum) a couple of years ago -- I shut down all the computers, unplug the modem and Airport, wait five minutes, and then plug everything back in sequence.
    Last night after I got through yelling at my cable company, they ran some tests remotely and suggested that the problem was with the Airport base station. How can I check for the connectivity of that? What in the System Preferences or Airport Setup can I look at? Thanks.

    Change the wireless channel on your AirPort Extreme to try to avoid the interference that you are picking up from the Linksys router in your vicinity.
    Open AirPort Utility - click Manual Setup
    Click the Wireless tab/label located just below the row of icons
    Start with Channel 11
    Update to save your changes
    Keep trying different channels working your way down until you find a clear channel, or you run out of channels

  • IMac always falling off the network

    I have my iMac always on, serving up our big ITunes library to our wireless network around the house. It seems to fall off the network fairly regularly, every few days or so. I have the newer Airport extreme and several Airport expresses (not the latest ones) connected to stereos in different rooms of the houses.
    But this has always happened, for a year or so. Anyone know what it might be? thanks!

    I have exactly the same problem and called tech support (not helpful at all, they need to work on their listening skills) and have no idea what is going on. I have found a temporary solution and that is to reset the basestation and not use any security or hardware access and it seems to work fine for a long time with no problems. my problem (not sure if this is the same problem as you but...) whenever I put any kind os security or hardware acccess on the network my mac either can seem to find the thing or does and randomly cuts out. I of course check my signal strength and it always says it is full.
    any help please

  • IPad Mini connected to home network but still not connecting to internet.

    Hi. I have a friend staying and she has an iPad mini. while all other Mac devises are connected to our home internet, her one will not. I have set the network details on her mini using the static ip option and get the blue tick beside our network name. However, we are still not connected to the wifi network. All our Mac devises are connected and her husband's iPad and iPhone are working fine. Help

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
    http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are drooping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    iPad: Issues connecting to Wi-Fi networks
    http://support.apple.com/kb/ts3304
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How to Change Your iPhone’s (iPad’s) DNS Servers
    http://www.macinstruct.com/node/558
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Is there a way to shut off 3g network and still have the WiFi working?

    My Dads going overseas and wants to use his Wifi but dosen't want to be charged using the 3G network.

    Because Airplane Mode turns off ALL iPhone radios...ALL. That way, there is no way to accidentally use cellular data. We get posts from users all the time that fail to use Airplane Mode & come home to bills from their carriers in the thousands. Do not rely on that data roaming switch.

  • Slow authentication when off home network

    Hi,
    I use my G4 in the office, at home, and on the road. My network guys at work set me up with a "mobile account". When I log in at work, it takes less than 15 seconds after hitting the "login" button before the standard OS X screen starts assembling itself, which is great. Logins are similarly rapid when I'm somewhere without network access, like on a plane. My problem only kicks in where my Airport can detect a wireless network, e.g. at home or in the airport. When my computer can sense a network but I'm not at work, logging in takes an inordinately long time (at least five minutes).
    I am not a net jock, but I know enough to suspect that this delay has something to do with an attempt to authenticate. Any suggestions on how to change my settings such that authentication is only attempted on my office network, and just use cached data elsewhere?
    Thanks,
    Chris

    You probably need a local firewall to block outbound kerberos traffic (port 88 udp/tcp) when you are off your home net. See:
    http://eportg.cgc.maricopa.edu/published/t/ss/tss-unix/wiki/1/index.shtml?Macx/K erberosTimeout
    iBook G4 12"   Mac OS X (10.4.6)   white

  • Apple Devices Dropping Off Wireless Network

    Hello, I have recently deployed a wireless network using a WLC 2504 with 21 Light APs. All seems fine except that
    Apple Devices drop their connections every 15 minutes or so. A couple of minutes later they can reconnect but
    obviously something is wrong.
    Many Thanks

    Only Apple device exhibit this kind of behaviour?
    What kind of Apple devices?  Mac laptops?  iPad, iTouch, iPhone?
    Have you seen this behaviour from, say, non-Apple devices?  Android?  Windows laptops?
    What are the signal strengths when this happens?
    Do you have Aironet IE enabled?
    How far are the clients from the WAP(s)?

  • Name of my iMac suddenly changed on home network

    I received a prompt saying the name of my iMac was being changed on the because there is another computer with the same name on my network. I have no idea why this happened. As far as I can tell, my iMac is the only one with that original name. Can anyone tell me why this happened. I have virus barrier 6 installed, and there is no indication of outside mischief.

    There are several potential causes for this, among them is having mounted an additional volume containing OS X.
    williamfromsaddlebrooke wrote:
    ... I have virus barrier 6 installed, and there is no indication of outside mischief.
    Intego Virus Barrier is self-infliced mischief. Get rid of it. It will do nothing but cause problems for you.
    Be sure to follow Intego's uninstallation instructions with care, and verify its complete eradication.
    Do not install such junk on a Mac.

Maybe you are looking for

  • XI: Sender JDBC Communication Channel is not getting picked the records

    Hi All, Here I 'm facing an Issue with my sender JDBC communication Channel. Previously it was working fine but It is not Picking the records from the JDBC table. Communication Channel is in active mode only. I have checked in RWB communication Chann

  • Attachments in Apple Mail scrambled

    When I try to look at attachments (PDFs and Word docs) in Apple Mail they sometimes (but not always) get converted into scrambled text that is embedded at the bottom of the email. Like this.... ----NEXT_BM_AB726E6E67FB42CBAC2285AF00AF803D Content-Typ

  • Looking for the best MBPR case.

    I was looking at going for a sleeve case and a backpack for my retina macbook pro. The sleeve I was looking at is the Thule 15" Sleeve however I am worried about the zips and the excess room. Backpack would be the Incase Compact Backpack with the mac

  • Rfc code to call  any sap tcode  in excel macro

    Hi all,          We are trying call sap tcode in excel macro programm using RFC.          Can any one  send me sample code for this?          This is urgent.points will be rewarded. regards, Shyam

  • Implementing Adobe Document Services (ADS) in portal with MSS scenario

    Hi, Has anyone implemented the new MSS scenario (ECC 6.0) on NW 2004S yet? We're trying to implement ADS to show us the trip and travelforms in PDF and have hence followed the ADS config guide for this. We used Basic Authentication and I thought this