IMac G5 doesn´t start after 10.4.4 upgrade
My Imac G5 20" 1,8 Ghz was fine on 10.3.9. I bought Tiger, upgraded from disk to 10.4.0 - everything seemed fine. Then I did software actualization to 10.4.4 (combo, + Java upgrades etc), now it crashes at startup from the apple-screen into a kernel panic which reads: "PowerMac8,1 driver not found".
I zapped the pram, repaired permissions, tested the harddrive - appeared to be ok.
Any ideas?
Try running the Tiger install and Combo update again, supergolff (or even just the combo to 10.4.4 if you have access to another bootable Tiger external drive)
Cheers
Rod
Similar Messages
-
IMac 24" doesn't start after installing Mavericks.
After installing Mavericks (10.9.2) the machine started having hiccups... rebooting at random times on it's own. After upgrading to 10.9.3, it only got worse. Reboots were more frequent (as little as 1 minute between each reboot). Then it took the final step and went into a state where it remains with black screen, the startup jingle may begin, but is killed within half a second or less... goes into a reboot loop. The DVD sounds, then it tries to reboot again, DVD sounds... sometimes the jingle starts... but is cut off by a reboot. Trying to get ANYTHING done with different key press combinations (option+command+R+P, D, T, Command, Option... pretty much every single combination one can find online for accessing safe boot or recovery or whatever... does not work. The machine seems to have been killed by Mavericks. I have come across a LOT of posts by other people who have experienced the same thing (rebooting after installing Mavericks) going back to October last year, and a few have experienced the same dead computer issue as I am having... all the while there is no fix or explanation from APPLE regarding this issue. I have even opened the machine up and checked all cable connections, tested the HDD on another computer (was ok), cleaned the memory module connectors etc. Before the total crash I had installed a temperature monitoring program with ventilator control, due to the DVD ventilator running at high RPM after installing Maverics. All the temp sensors were reporting modest temps (ranging from 39 - 79 Celsius (only the power supply was above 50 Celsius).
The computer is as useful as a brick by this point. Since it went dead, it has successfully started up 3 times (out of 500+ attempts), but rebooted within a couple of minutes, into it's cycle of dead reboots.
One way of getting it to boot and prepare for re-installation, is to keep the power button pressed until it sounds 3 times long, 3 times short and 3 times long beeps... it would only start making the first beep... then it rebooted in to death again.
Could it be that Mavericks is destroying the firmware, or even killing the hardware? I also have Mavericks on MBA and MBP, where the MBA has no problems, while the MBP freezes up every 2 days or so... requiring a forced reboot.
Anyone with a usable advice on what to do in order to get the machine working again? How many years does it normally take APPLE support staff to fix serious issues like this one? It's already been over 7 months since the first people began experiencing these issues with Mavericks, but nothing has been done about it on APPLE's end ... as far as I can tell.
Looking forward to some solutions.Just wanted to write the conclusion of this issue here, and make things as clear as possible.
I took the iMac to a support center, and they confirmed that several components on the power supply board were fried and other parts had been overheated. It took a few weeks for them to get the needed parts (much cheaper than replacing the entire unit). I brought the iMac back home and started it up, and it did work... but it was getting very hot very quickly. I was thinking that maybe I should install Mountain Lion on it, and get away from Mavericks... just in case.... the computer had been turned on for around 1 hour at that point, and then it rebooted.... and stayed dead for 10 minutes or so... until it could start up again. Was on for a few minutes... then dead again.
Clearly the cause of the problem was still present, and fixing the symptom did not prove to be a lasting solution.
The machine would not stay turned on long enough (when it DID turn on) for even formatting the disk, so I removed the SDD from it, formatted it with my MBA (connected through USB), and inserted it in the iMac again. Starting it up resulted in a few minutes being turned on, overheating and crashing. Having downloaded ML and created a USB installer for it, it was now a case of trying one's patience ... hoping for the machine to stay turned on long enough to make it all the way through the installation process.... it managed to do the first part of the installation after several hours of crashing and overheating.... and it came to a point where I simply turned it off and gave up... thinking that the problem simply was physical in nature, and not caused by Mavericks as I had assumed from the start. Next day I had renewed energy, turned the puter on and it behaved in the same way... turning off, then starting by itself trying to get through the installation.... it would fail again and again... I left the house, with it turned on, hoping that it would at least manage to finish at some point in time... so that I could write off my "BAD Mavericks" suspicion. When I returned several hours later, the installation was complete and the machine was purring quietly and the back of the computer was NOT hot like a steam iron.
Now it has been working for several days without any problems at all.
The final conclusion is this:
Mavericks IS at fault, and will physically DESTROY computers that are "somehow" not compatible with it. I would have thought that Apple had enough capable engineers to prevent the operating system to mess up the hardware in this way, but clearly I was wrong on that account. I can only WARN other people to even attempt installing Mavericks on puters of this type:
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number of Processors: 1
Total Number of Cores: 2
L2 Cache: 4 MB
Memory: 4 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4
Serial Number (system): W8*******X89
Hardware UUID: 00000000-0000-1000-8000-001B639688F7
Anyone claiming that Mavericks is not at fault, is plain and simple WRONG, in DENIAL or LYING. There is absolutely NO doubt in my mind any longer, that the problem was indeed Mavericks getting installed on the machine and messing with the hardware on a level where it should never happen. If someone working at Apple would like to purchase/replace my iMac in order to test it and figure out that this is a REAL problem, they are welcome to do so. I think it is more than guaranteed that the damage caused by this Mavericks nightmare installation will never be recovered, nor will the time and work lost ever be compensated, but I would actually like Apple to acknowledge their responsibility and failure to address this issue in a professional and responsible way.
IF Mavericks was NOT at fault, then someone should explain the logic behind the machine physically burning components shortly after the installation of Mavericks, and even when the SDD had been wiped clean with no OS, it was still overheating and shutting off, until it could finally have ML installed... and at that point it was cured and has worked flawlessly ever since. Not a single hiccup, no over heating, no problems.
My offer to sell/replace the iMac stands if Apple is really interested in looking at this SERIOUS issue with Mavericks. This is NOT a minor issue they should expect simply goes away, or will be ignored by people who experience their machines BURNING to pieces.
On my MBA and MBP Mavericks is not causing any problems, so it is not "all bad", but for the iMac it meant total annihilation.
Anyone who has installed Mavericks on their iMac of similar age as mine, having rebooting and overheating problems: REMOVE the Mavericks installation ASAP and get ML on it before it goes up in flames!
Other Mac's have been reported having the rebooting/overheating problems as well, although I have not noted down which builds those were. The problem is REAL and COSTLY for those who experience it.... both time-wise and in terms of lost time/work.
Hopefully this will help others from getting the same terrible experience as I got, and save some computers from burning up.
<Personal Information Edited by Host> -
Instruments doesn't start after my Mountain Lion upgrade. Please help me.
When I try to start Instruments after my Mountain Lion upgrade I get this popup:
"You can't open the application "Instruments.app" because it may be damaged or incomplete."
Does anyone know how to fix this?When I looked for an link to explain what Instrument is, http://en.wikipedia.org/wiki/Instruments_(application), I found that it's completly integrated in Xcode since Xcode 3.0.
Thank you for being interested. -
[SOLVED] Xorg doesn't start after upgrade to 1.17.1
Archlinux i686
Intel Core 2 Duo 6600
01:00.0 VGA compatible controller: NVIDIA Corporation G71 [GeForce 7900 GT/GTO] (rev a1)
After following upgrades:
[2015-02-26 03:27] [PACMAN] Running 'pacman -S mesa mesa-demos mesa-libgl'
[2015-02-26 03:27] [ALPM] transaction started
[2015-02-26 03:28] [ALPM] upgraded mesa (10.4.2-1 -> 10.4.5-1)
[2015-02-26 03:28] [ALPM] upgraded mesa-libgl (10.4.2-1 -> 10.4.5-1)
[2015-02-26 03:28] [ALPM] upgraded mesa-demos (8.2.0-3 -> 8.2.0-4)
[2015-02-26 03:28] [ALPM] transaction completed
[2015-02-26 03:28] [PACMAN] Running 'pacman -S xorg-server xorg-server-common'
[2015-02-26 03:29] [ALPM] transaction started
[2015-02-26 03:29] [ALPM] removed xf86-video-vesa (2.3.2-5)
[2015-02-26 03:29] [ALPM] removed xf86-video-nouveau (1.0.11-2)
[2015-02-26 03:29] [ALPM] removed xf86-video-modesetting (0.9.0-2)
[2015-02-26 03:29] [ALPM] upgraded xorg-server-common (1.16.3-2 -> 1.17.1-3)
[2015-02-26 03:29] [ALPM] upgraded xorg-server (1.16.3-2 -> 1.17.1-3)
Xorg doesn't start after reboot and I found following kernel message:
kernel: [drm:drm_mmap_locked] *ERROR* Could not find map
and /var/log/Xorg.0.log looks like this:
[ 5.591]
X.Org X Server 1.17.1
Release Date: 2015-02-10
[ 5.591] X Protocol Version 11, Revision 0
[ 5.591] Build Operating System: Linux 3.18.6-1-ARCH i686
[ 5.591] Current Operating System: Linux emeria7 3.18.6-1-ARCH #1 SMP PREEMPT Sat Feb 7 08:59:29 CET 2015 i686
[ 5.591] Kernel command line: root=/dev/disk/by-label/archroot rw
[ 5.591] Build Date: 22 February 2015 12:52:47PM
[ 5.591]
[ 5.592] Current version of pixman: 0.32.6
[ 5.592] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 5.592] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 5.592] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Feb 26 14:58:35 2015
[ 5.597] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 5.597] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 5.598] (==) ServerLayout "ServerLayout0"
[ 5.598] (==) No screen section available. Using defaults.
[ 5.598] (**) |-->Screen "Default Screen Section" (0)
[ 5.598] (**) | |-->Monitor "<default monitor>"
[ 5.599] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 5.599] (**) | |-->Device "Device0"
[ 5.599] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 5.599] (**) Option "BlankTime" "0"
[ 5.599] (**) Option "StandbyTime" "0"
[ 5.599] (**) Option "SuspendTime" "0"
[ 5.599] (**) Option "OffTime" "0"
[ 5.599] (==) Automatically adding devices
[ 5.599] (==) Automatically enabling devices
[ 5.599] (==) Automatically adding GPU devices
[ 5.608] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 5.608] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 5.608] (**) Extension "Composite" is disabled
[ 5.608] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 5.608] (II) Loader magic: 0x829e700
[ 5.608] (II) Module ABI versions:
[ 5.608] X.Org ANSI C Emulation: 0.4
[ 5.608] X.Org Video Driver: 19.0
[ 5.608] X.Org XInput driver : 21.0
[ 5.608] X.Org Server Extension : 9.0
[ 5.611] (EE) systemd-logind: failed to get session: PID 995 does not belong to any known session
[ 5.611] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 5.612] (--) PCI:*(0:1:0:0) 10de:0291:107d:2a62 rev 161, Mem @ 0xfd000000/16777216, 0xc0000000/268435456, 0xfc000000/16777216, I/O @ 0x0000ac00/128, BIOS @ 0x????????/131072
[ 5.612] (II) Open ACPI successful (/var/run/acpid.socket)
[ 5.613] (II) LoadModule: "glx"
[ 5.616] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 5.632] (II) Module glx: vendor="X.Org Foundation"
[ 5.632] compiled for 1.17.1, module version = 1.0.0
[ 5.632] ABI class: X.Org Server Extension, version 9.0
[ 5.632] (==) AIGLX enabled
[ 5.632] (==) Matched nouveau as autoconfigured driver 0
[ 5.632] (==) Matched nv as autoconfigured driver 1
[ 5.632] (==) Matched nouveau as autoconfigured driver 2
[ 5.632] (==) Matched nv as autoconfigured driver 3
[ 5.632] (==) Matched modesetting as autoconfigured driver 4
[ 5.632] (==) Matched fbdev as autoconfigured driver 5
[ 5.632] (==) Matched vesa as autoconfigured driver 6
[ 5.632] (==) Assigned the driver to the xf86ConfigLayout
[ 5.632] (II) LoadModule: "nouveau"
[ 5.632] (WW) Warning, couldn't open module nouveau
[ 5.632] (II) UnloadModule: "nouveau"
[ 5.632] (II) Unloading nouveau
[ 5.632] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 5.633] (II) LoadModule: "nv"
[ 5.633] (WW) Warning, couldn't open module nv
[ 5.633] (II) UnloadModule: "nv"
[ 5.633] (II) Unloading nv
[ 5.633] (EE) Failed to load module "nv" (module does not exist, 0)
[ 5.633] (II) LoadModule: "modesetting"
[ 5.633] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 5.634] (II) Module modesetting: vendor="X.Org Foundation"
[ 5.634] compiled for 1.17.1, module version = 1.17.1
[ 5.634] Module class: X.Org Video Driver
[ 5.634] ABI class: X.Org Video Driver, version 19.0
[ 5.634] (II) LoadModule: "fbdev"
[ 5.634] (WW) Warning, couldn't open module fbdev
[ 5.634] (II) UnloadModule: "fbdev"
[ 5.634] (II) Unloading fbdev
[ 5.634] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 5.634] (II) LoadModule: "vesa"
[ 5.634] (WW) Warning, couldn't open module vesa
[ 5.634] (II) UnloadModule: "vesa"
[ 5.634] (II) Unloading vesa
[ 5.634] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 5.634] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 5.634] (++) using VT number 7
[ 5.635] (II) modeset(0): using drv /dev/dri/card0
[ 5.635] (II) modeset(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 5.636] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[ 5.636] (==) modeset(0): RGB weight 888
[ 5.636] (==) modeset(0): Default visual is TrueColor
[ 5.636] (II) Loading sub module "glamoregl"
[ 5.636] (II) LoadModule: "glamoregl"
[ 5.636] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 5.647] (II) Module glamoregl: vendor="X.Org Foundation"
[ 5.647] compiled for 1.17.1, module version = 1.0.0
[ 5.647] ABI class: X.Org ANSI C Emulation, version 0.4
[ 5.647] (II) glamor: OpenGL accelerated X.org driver based.
[ 5.772] (II) glamor: EGL version 1.4 (DRI2):
[ 5.786] (II) modeset(0): glamor initialized
[ 5.786] (II) Loading sub module "dri2"
[ 5.786] (II) LoadModule: "dri2"
[ 5.786] (II) Module "dri2" already built-in
[ 5.843] (II) modeset(0): Output DVI-0 has no monitor section
[ 5.896] (II) modeset(0): Output DVI-1 has no monitor section
[ 5.950] (II) modeset(0): Output TV-0 has no monitor section
[ 6.006] (II) modeset(0): EDID for output DVI-0
[ 6.006] (II) modeset(0): Manufacturer: SAM Model: 76f Serial#: 1110590261
[ 6.006] (II) modeset(0): Year: 2011 Week: 8
[ 6.006] (II) modeset(0): EDID Version: 1.3
[ 6.006] (II) modeset(0): Digital Display Input
[ 6.006] (II) modeset(0): Max Image Size [cm]: horiz.: 51 vert.: 29
[ 6.006] (II) modeset(0): Gamma: 2.20
[ 6.006] (II) modeset(0): DPMS capabilities: Off
[ 6.006] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 6.006] (II) modeset(0): First detailed timing is preferred mode
[ 6.006] (II) modeset(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
[ 6.006] (II) modeset(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
[ 6.006] (II) modeset(0): Supported established timings:
[ 6.006] (II) modeset(0): 720x400@70Hz
[ 6.006] (II) modeset(0): 640x480@60Hz
[ 6.006] (II) modeset(0): 640x480@67Hz
[ 6.006] (II) modeset(0): 640x480@72Hz
[ 6.006] (II) modeset(0): 640x480@75Hz
[ 6.006] (II) modeset(0): 800x600@56Hz
[ 6.006] (II) modeset(0): 800x600@60Hz
[ 6.006] (II) modeset(0): 800x600@72Hz
[ 6.006] (II) modeset(0): 800x600@75Hz
[ 6.006] (II) modeset(0): 832x624@75Hz
[ 6.006] (II) modeset(0): 1024x768@60Hz
[ 6.006] (II) modeset(0): 1024x768@70Hz
[ 6.006] (II) modeset(0): 1024x768@75Hz
[ 6.006] (II) modeset(0): 1280x1024@75Hz
[ 6.006] (II) modeset(0): 1152x864@75Hz
[ 6.006] (II) modeset(0): Manufacturer's mask: 0
[ 6.006] (II) modeset(0): Supported standard timings:
[ 6.006] (II) modeset(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 6.006] (II) modeset(0): #1: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 6.006] (II) modeset(0): #2: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 6.006] (II) modeset(0): #3: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 6.006] (II) modeset(0): #4: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 6.006] (II) modeset(0): #5: hsize: 1440 vsize 900 refresh: 75 vid: 3989
[ 6.007] (II) modeset(0): #6: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 6.007] (II) modeset(0): #7: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 148.5 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 6.007] (II) modeset(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 74.2 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 6.007] (II) modeset(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 6.007] (II) modeset(0): Ranges: V min: 50 V max: 75 Hz, H min: 31 H max: 81 kHz, PixClock max 175 MHz
[ 6.007] (II) modeset(0): Monitor name: SMBX2331
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 74.2 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 6.007] (II) modeset(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 74.2 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 6.007] (II) modeset(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 74.2 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 6.007] (II) modeset(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 27.0 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 6.007] (II) modeset(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 6.007] (II) modeset(0): Supported detailed timing:
[ 6.007] (II) modeset(0): clock: 27.0 MHz Image Size: 509 x 286 mm
[ 6.007] (II) modeset(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 6.007] (II) modeset(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 6.007] (II) modeset(0): Number of EDID sections to follow: 1
[ 6.007] (II) modeset(0): EDID (in hex):
[ 6.007] (II) modeset(0): 00ffffffffffff004c2d6f0735433242
[ 6.007] (II) modeset(0): 0815010380331d782aee91a3544c9926
[ 6.007] (II) modeset(0): 0f5054bfef80714f8100814081809500
[ 6.007] (II) modeset(0): 950fa940b300023a801871382d40582c
[ 6.007] (II) modeset(0): 4500fd1e1100001e011d007251d01e20
[ 6.007] (II) modeset(0): 6e285500fd1e1100001e000000fd0032
[ 6.007] (II) modeset(0): 4b1f5111000a202020202020000000fc
[ 6.007] (II) modeset(0): 00534d4258323333310a2020202001ee
[ 6.007] (II) modeset(0): 02031cf14890041f0514131203230907
[ 6.007] (II) modeset(0): 078301000066030c00100080011d80d0
[ 6.007] (II) modeset(0): 721c1620102c2580fd1e1100009e011d
[ 6.007] (II) modeset(0): 8018711c1620582c2500fd1e1100009e
[ 6.007] (II) modeset(0): 011d00bc52d01e20b8285540fd1e1100
[ 6.007] (II) modeset(0): 001e8c0ad090204031200c405500fd1e
[ 6.007] (II) modeset(0): 110000188c0ad08a20e02d10103e9600
[ 6.007] (II) modeset(0): fd1e110000180000000000000000004c
[ 6.007] (II) modeset(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
[ 6.007] (II) modeset(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
[ 6.007] (II) modeset(0): Printing probed modes for output DVI-0
[ 6.007] (II) modeset(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 6.007] (II) modeset(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 6.007] (II) modeset(0): Modeline "1920x1080"x59.9 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.4 kHz e)
[ 6.007] (II) modeset(0): Modeline "1600x1200"x65.0 175.50 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (81.2 kHz d)
[ 6.007] (II) modeset(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1680x1050"x59.9 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[ 6.007] (II) modeset(0): Modeline "1400x1050"x74.8 155.80 1400 1464 1784 1912 1050 1052 1064 1090 +hsync +vsync (81.5 kHz d)
[ 6.007] (II) modeset(0): Modeline "1400x1050"x60.0 122.00 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)
[ 6.007] (II) modeset(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 6.007] (II) modeset(0): Modeline "1440x900"x59.9 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x800"x59.9 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 6.007] (II) modeset(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 6.007] (II) modeset(0): Modeline "1280x720"x59.9 74.18 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 6.007] (II) modeset(0): Modeline "1024x768"x75.0 170.24 1024 1108 1220 1416 768 768 770 801 doublescan -hsync +vsync (120.2 kHz d)
[ 6.007] (II) modeset(0): Modeline "1024x768"x60.0 133.47 1024 1100 1212 1400 768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)
[ 6.007] (II) modeset(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 6.007] (II) modeset(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz d)
[ 6.007] (II) modeset(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 6.007] (II) modeset(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 6.008] (II) modeset(0): Modeline "960x720"x75.0 148.50 960 1032 1144 1320 720 720 722 750 doublescan -hsync +vsync (112.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "960x720"x60.0 117.00 960 1024 1128 1300 720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "928x696"x75.0 144.00 928 992 1104 1280 696 696 698 750 doublescan -hsync +vsync (112.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "928x696"x60.1 109.15 928 976 1088 1264 696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)
[ 6.008] (II) modeset(0): Modeline "896x672"x75.0 130.50 896 944 1052 1228 672 672 674 708 doublescan -hsync +vsync (106.3 kHz d)
[ 6.008] (II) modeset(0): Modeline "896x672"x60.0 102.40 896 960 1060 1224 672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)
[ 6.008] (II) modeset(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 6.008] (II) modeset(0): Modeline "800x600"x75.0 101.25 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (93.8 kHz d)
[ 6.008] (II) modeset(0): Modeline "800x600"x70.0 94.50 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (87.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "800x600"x65.0 87.75 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (81.2 kHz d)
[ 6.008] (II) modeset(0): Modeline "800x600"x60.0 81.00 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 6.008] (II) modeset(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 6.008] (II) modeset(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 6.008] (II) modeset(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 6.008] (II) modeset(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 6.008] (II) modeset(0): Modeline "700x525"x74.8 77.90 700 732 892 956 525 526 532 545 doublescan +hsync +vsync (81.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "700x525"x60.0 61.00 700 744 820 940 525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)
[ 6.008] (II) modeset(0): Modeline "720x480"x60.0 27.03 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "640x512"x75.0 67.50 640 648 720 844 512 512 514 533 doublescan +hsync +vsync (80.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "640x512"x60.0 54.00 640 664 720 844 512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "640x480"x60.0 54.00 640 688 744 900 480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 6.008] (II) modeset(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz d)
[ 6.008] (II) modeset(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 6.008] (II) modeset(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 6.008] (II) modeset(0): Modeline "576x432"x75.0 54.00 576 608 672 800 432 432 434 450 doublescan +hsync +vsync (67.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "512x384"x75.0 39.38 512 520 568 656 384 384 386 400 doublescan +hsync +vsync (60.0 kHz d)
[ 6.008] (II) modeset(0): Modeline "512x384"x70.1 37.50 512 524 592 664 384 385 388 403 doublescan -hsync -vsync (56.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "512x384"x60.0 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)
[ 6.008] (II) modeset(0): Modeline "416x312"x74.7 28.64 416 432 464 576 312 312 314 333 doublescan -hsync -vsync (49.7 kHz d)
[ 6.008] (II) modeset(0): Modeline "400x300"x72.2 25.00 400 428 488 520 300 318 321 333 doublescan +hsync +vsync (48.1 kHz d)
[ 6.008] (II) modeset(0): Modeline "400x300"x75.1 24.75 400 408 448 528 300 300 302 312 doublescan +hsync +vsync (46.9 kHz d)
[ 6.008] (II) modeset(0): Modeline "400x300"x60.3 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)
[ 6.008] (II) modeset(0): Modeline "400x300"x56.3 18.00 400 412 448 512 300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)
[ 6.008] (II) modeset(0): Modeline "320x240"x72.8 15.75 320 332 352 416 240 244 246 260 doublescan -hsync -vsync (37.9 kHz d)
[ 6.008] (II) modeset(0): Modeline "320x240"x75.0 15.75 320 328 360 420 240 240 242 250 doublescan -hsync -vsync (37.5 kHz d)
[ 6.008] (II) modeset(0): Modeline "320x240"x60.1 12.59 320 328 376 400 240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)
[ 6.063] (II) modeset(0): EDID for output DVI-1
[ 6.116] (II) modeset(0): EDID for output TV-0
[ 6.116] (II) modeset(0): Output DVI-0 connected
[ 6.116] (II) modeset(0): Output DVI-1 disconnected
[ 6.116] (II) modeset(0): Output TV-0 disconnected
[ 6.116] (II) modeset(0): Using exact sizes for initial modes
[ 6.116] (II) modeset(0): Output DVI-0 using initial mode 1920x1080
[ 6.116] (II) modeset(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 6.116] (==) modeset(0): DPI set to (96, 96)
[ 6.116] (II) Loading sub module "fb"
[ 6.116] (II) LoadModule: "fb"
[ 6.117] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 6.118] (II) Module fb: vendor="X.Org Foundation"
[ 6.118] compiled for 1.17.1, module version = 1.0.0
[ 6.118] ABI class: X.Org ANSI C Emulation, version 0.4
[ 6.118] (==) Depth 24 pixmap format is 32 bpp
[ 6.462] (==) modeset(0): Backing store disabled
[ 6.462] (==) modeset(0): Silken mouse enabled
[ 6.464] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6.535] (==) modeset(0): DPMS enabled
[ 6.535] (WW) modeset(0): Option "EXANoComposite" is not used
[ 6.535] (II) modeset(0): [DRI2] Setup complete
[ 6.535] (II) modeset(0): [DRI2] DRI driver: nouveau
[ 6.535] (II) modeset(0): [DRI2] VDPAU driver: nouveau
[ 6.535] (--) RandR disabled
[ 6.551] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 6.551] (II) AIGLX: enabled GLX_ARB_create_context
[ 6.551] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 6.551] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 6.551] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 6.551] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 6.551] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 6.551] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 6.551] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 6.552] (II) AIGLX: Loaded and initialized nouveau
[ 6.552] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 6.559] (II) modeset(0): Setting screen physical size to 507 x 285
[ 6.741] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 6.741] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 6.741] (**) Power Button: Applying InputClass "Keyboard Defaults"
[ 6.741] (II) LoadModule: "evdev"
[ 6.741] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 6.744] (II) Module evdev: vendor="X.Org Foundation"
[ 6.744] compiled for 1.16.2, module version = 2.9.1
[ 6.744] Module class: X.Org XInput Driver
[ 6.744] ABI class: X.Org XInput driver, version 21.0
[ 6.744] (II) Using input driver 'evdev' for 'Power Button'
[ 6.744] (**) Power Button: always reports core events
[ 6.744] (**) evdev: Power Button: Device: "/dev/input/event3"
[ 6.744] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 6.744] (--) evdev: Power Button: Found keys
[ 6.744] (II) evdev: Power Button: Configuring as keyboard
[ 6.744] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[ 6.744] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 6.744] (**) Option "xkb_rules" "evdev"
[ 6.744] (**) Option "xkb_model" "pc104"
[ 6.744] (**) Option "xkb_layout" "us"
[ 6.744] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 6.780] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 6.780] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 6.780] (**) Power Button: Applying InputClass "Keyboard Defaults"
[ 6.780] (II) Using input driver 'evdev' for 'Power Button'
[ 6.780] (**) Power Button: always reports core events
[ 6.780] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 6.780] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 6.780] (--) evdev: Power Button: Found keys
[ 6.780] (II) evdev: Power Button: Configuring as keyboard
[ 6.780] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2/event2"
[ 6.780] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 6.780] (**) Option "xkb_rules" "evdev"
[ 6.780] (**) Option "xkb_model" "pc104"
[ 6.780] (**) Option "xkb_layout" "us"
[ 6.780] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 6.781] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event4)
[ 6.781] (II) No input driver specified, ignoring this device.
[ 6.781] (II) This device may have been added with another device file.
[ 6.782] (II) config/udev: Adding input device HDA Intel Line Out Side (/dev/input/event10)
[ 6.782] (II) No input driver specified, ignoring this device.
[ 6.782] (II) This device may have been added with another device file.
[ 6.782] (II) config/udev: Adding input device HDA Intel Rear Mic (/dev/input/event5)
[ 6.782] (II) No input driver specified, ignoring this device.
[ 6.782] (II) This device may have been added with another device file.
[ 6.782] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event6)
[ 6.782] (II) No input driver specified, ignoring this device.
[ 6.782] (II) This device may have been added with another device file.
[ 6.783] (II) config/udev: Adding input device HDA Intel Line Out Front (/dev/input/event7)
[ 6.783] (II) No input driver specified, ignoring this device.
[ 6.783] (II) This device may have been added with another device file.
[ 6.783] (II) config/udev: Adding input device HDA Intel Line Out Surround (/dev/input/event8)
[ 6.783] (II) No input driver specified, ignoring this device.
[ 6.783] (II) This device may have been added with another device file.
[ 6.783] (II) config/udev: Adding input device HDA Intel Line Out CLFE (/dev/input/event9)
[ 6.783] (II) No input driver specified, ignoring this device.
[ 6.783] (II) This device may have been added with another device file.
[ 6.784] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/event1)
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 6.784] (II) Using input driver 'evdev' for 'Logitech USB-PS/2 Optical Mouse'
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: always reports core events
[ 6.784] (**) evdev: Logitech USB-PS/2 Optical Mouse: Device: "/dev/input/event1"
[ 6.784] (--) evdev: Logitech USB-PS/2 Optical Mouse: Vendor 0x46d Product 0xc050
[ 6.784] (--) evdev: Logitech USB-PS/2 Optical Mouse: Found 12 mouse buttons
[ 6.784] (--) evdev: Logitech USB-PS/2 Optical Mouse: Found scroll wheel(s)
[ 6.784] (--) evdev: Logitech USB-PS/2 Optical Mouse: Found relative axes
[ 6.784] (--) evdev: Logitech USB-PS/2 Optical Mouse: Found x and y relative axes
[ 6.784] (II) evdev: Logitech USB-PS/2 Optical Mouse: Configuring as mouse
[ 6.784] (II) evdev: Logitech USB-PS/2 Optical Mouse: Adding scrollwheel support
[ 6.784] (**) evdev: Logitech USB-PS/2 Optical Mouse: YAxisMapping: buttons 4 and 5
[ 6.784] (**) evdev: Logitech USB-PS/2 Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 6.784] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-1/6-1:1.0/0003:046D:C050.0001/input/input1/event1"
[ 6.784] (II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE, id 8)
[ 6.784] (II) evdev: Logitech USB-PS/2 Optical Mouse: initialized for relative axes.
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: (accel) keeping acceleration scheme 1
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration profile 0
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration factor: 2.000
[ 6.784] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration threshold: 4
[ 6.785] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/mouse0)
[ 6.785] (II) No input driver specified, ignoring this device.
[ 6.785] (II) This device may have been added with another device file.
[ 6.785] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 6.785] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 6.785] (**) AT Translated Set 2 keyboard: Applying InputClass "Keyboard Defaults"
[ 6.785] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 6.785] (**) AT Translated Set 2 keyboard: always reports core events
[ 6.785] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 6.785] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 6.785] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 6.785] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 6.785] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 6.785] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 6.785] (**) Option "xkb_rules" "evdev"
[ 6.785] (**) Option "xkb_model" "pc104"
[ 6.785] (**) Option "xkb_layout" "us"
[ 6.785] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 6.803] (EE)
[ 6.803] (EE) Backtrace:
[ 6.803] (EE) 0: /usr/lib/xorg-server/Xorg (OsLookupColor+0x132) [0x81df9e2]
[ 6.804] (EE) 1: ? (?+0x132) [0xb7787cc5]
[ 6.804] (EE) 2: /usr/lib/xorg/modules/drivers/modesetting_drv.so (_init+0x4cd7) [0xb6e2a1c7]
[ 6.806] (EE) 3: /usr/lib/xorg-server/Xorg (xf86_show_cursors+0x688) [0x80f9008]
[ 6.806] (EE) 4: /usr/lib/xorg-server/Xorg (xf86DestroyCursorInfoRec+0xcf8) [0x8103fc8]
[ 6.806] (EE) 5: /usr/lib/xorg-server/Xorg (RamDacHandleColormaps+0x67b) [0x810218b]
[ 6.807] (EE) 6: /usr/lib/xorg-server/Xorg (miPointerUpdateSprite+0x25d) [0x81c648d]
[ 6.808] (EE) 7: /usr/lib/xorg-server/Xorg (miPointerUpdateSprite+0x4c1) [0x81c6b31]
[ 6.808] (EE) 8: /usr/lib/xorg-server/Xorg (CompositeRegisterImplicitRedirectionException+0x4199) [0x8114399]
[ 6.809] (EE) 9: /usr/lib/xorg-server/Xorg (PanoramiXRenderReset+0x72a) [0x815915a]
[ 6.810] (EE) 10: /usr/lib/xorg-server/Xorg (ConfineToShape+0x9f1) [0x80843b1]
[ 6.810] (EE) 11: /usr/lib/xorg-server/Xorg (WindowHasNewCursor+0x3b) [0x8084f2b]
[ 6.810] (EE) 12: /usr/lib/xorg-server/Xorg (ChangeWindowAttributes+0xb7c) [0x80aa9ec]
[ 6.811] (EE) 13: /usr/lib/xorg-server/Xorg (ProcBadRequest+0x209) [0x8074a49]
[ 6.811] (EE) 14: /usr/lib/xorg-server/Xorg (SendErrorToClient+0x3a6) [0x807abf6]
[ 6.811] (EE) 15: /usr/lib/xorg-server/Xorg (remove_fs_handlers+0x42f) [0x807edaf]
[ 6.811] (EE) 16: /usr/lib/xorg-server/Xorg (miPolyFillRect+0x27f) [0x8068ddf]
[ 6.814] (EE) 17: /usr/lib/libc.so.6 (__libc_start_main+0xde) [0xb72d864e]
[ 6.814] (EE) 18: /usr/lib/xorg-server/Xorg (_start+0x21) [0x8068bd9]
[ 6.814] (EE)
[ 6.814] (EE) Segmentation fault at address 0x0
[ 6.814] (EE)
Fatal server error:
[ 6.814] (EE) Caught signal 11 (Segmentation fault). Server aborting
[ 6.814] (EE)
[ 6.814] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 6.814] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 6.814] (EE)
[ 6.815] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 6.817] (EE) Server terminated with error (1). Closing log file.
Note the segfault in modesetting_drv.so!
Any help?
I tried to reinstall dependencies of xorg-server and mesa. And then I even went through with the whole system update which I postponed for a few weeks because of the KDE changes. Sadly even the whole system update didn't help.
Is it possible that any old config files can cause this?
EDIT:
I tried kernel parameter "nouveau.modeset=0" but it didn't help.
Last edited by cro (2015-02-26 16:33:19)Ok, I guess I solved it by reinstalling xf86-video-nouveau.
Funny business! Why did the upgrade to xorg-server 1.17.1 force me to remove it when it is still needed??
And why does that lead to mysterious error messages and segfault??
I discovered it accidentally when I stumbled upon the fact that the package was still installed on my newer x86-64 Arch installation despite being on xorg-server 1.17.1. -
DBConsole Service doesn't start after Install OAS F&R-Services Win 10g
Windows DBConsole Service doesn't start after Install OAS F&R-Services
Hello,
we have installed:
WINDOWS Server 2003 with SP 2
Oracle 10.2.0.1
OAS F&R Services 10.1.2.0.2
after Install DBR2 EM / DBConsole did work
after Install OAS F&R-Service
the windows-service for DBConsole
doesn't start, return with an Error Code 2
see below
the file named emdbconsole.nohup from output log
is not to find
the ias_console does work fine
OAS F_R-Services do work too
whats may be wrong ?
regards
Norbert
OracleDBConsoleorclsrvc.log :
EMDROOT=D:\oracle\product\10.2.0\db_1
ORACLE_HOME=D:\oracle\product\10.2.0\db_1
EMDSTATE=D:\oracle\product\10.2.0\db_1\kfin_orcl
CONSOLE_CFG=dbconsole
TRACE_LEVEL=16
TIMEOUT=15
12/14/09 13:13:08 Start pending...
12/14/09 13:13:08 Verifying dbconsole is not started already. Command line "D:\oracle\product\10.2.0\db_1\bin\emctl.bat" istatus dbconsole
12/14/09 13:13:09 dbconsole launch commandline is "D:\oracle\product\10.2.0\db_1\bin\emctl.bat" istart dbconsole
12/14/09 13:13:09 Tracking process launch...
12/14/09 13:13:39 dbconsole exited with retCode 2.
12/14/09 13:13:39 Check D:\oracle\product\10.2.0\db_1\kfin_orcl\sysman\log\emdbconsole.nohup for details
Edited by: astramare on Dec 15, 2009 8:43 AMHi,
1. Stop the DBConsole. (set ORACLE_SID first & ORACLE_HOME)
cd %ORACLE_HOME%\bin
emctl stop dbconsole
2. Update the <ORACLE_HOME>/<hostname_sid>/sysman/config/emd.properties file.
Change line from:
tracelevel.main=WARN
To
tracelevel.main=DEBUG
Decomment this line, so that the line becomes :
EMAGENT_PERL_TRACE_LEVEL=DEBUG
3. Update the <ORACLE__HOME>/<hostname_sid>/sysman/config/emomslogging.properties
Change line from:
log4j.rootCategory=WARN, emlogAppender, emtrcAppender
To
log4j.rootCategory=DEBUG, emlogAppender, emtrcAppender
4. Remove/backup all log files from ORACLE_HOME/<hostname_sid>/sysman/log
5. Start the dbconsole and upload the output of each command
- start the dbconsole: "emctl start dbconsole"
- issue "emctl clearstate"
- status the dbconsole: "emctl status dbconsole"
- check the status of the agent until it comes up: "emctl status agent"
- force an upload: emctl upload
6. Check If you are able to view the dbconsole Page & login
check below logs may be you can see the close error messages to solve the issue.
<ORACLE_HOME>/<hostname_sid>/sysman/log directory
<ORACLE_HOME>/<hostname_sid>/sysman/config/emoms.properties
Otherwise re-create the DBconsole using the metalink doc 278100.1 : How To Drop, Create And Recreate DB Control In A 10g Database. (Please check the steps from Recreate/ReConfig DB Control, if you want to re-create)
Thanks. -
FF doesn't start after update to version 27.0.1
FF doesn't start after update to version 27.0.1
Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214Firefox 27.0.1 is too new for me to know what unique issues it might have. I will message you a link to download the installer for Firefox 27.0 to see whether that reverses the problem.
-
Teamviewer doesn't start after resume from hibernation
Teamviewer doesn't start after resume from hibernation, what can I do to make it work?
I issued command "teamviewer --daemon start" but no success.Quote from: BOSSKILLER on 07-July-08, 00:03:29
That's probably BIOS bug, have a ask MSI here: http://ocss.msi.com.tw/ They can send you a new BIOS to try.
I supposed that this issue is caused by BIOS bug, and this speculation was confirmed. MSI Support has sent to me link with BIOS version 132, which solves the problem
Under this link you can find this BIOS: http://rapidshare.com/files/127845890/a7395ims.132.zip.html
Regards. -
The browser doesn't start after turning off and turning on the computer
The browser doesn't start after turning off and turning on the computer. I tried to delete the program entirely (along with personal preferences), create a new account, install a different browser versions. All this did not help. (I have Windows 7.) Help, please! Every day I have to reinstall Firefox!
Hello Nastena, try a clean re-install, certain Firefox problems can be solved by performing a ''Clean reinstall''. This means you '''remove Firefox program files''' and then reinstall Firefox. Please follow these steps:
'''Note:''' You might want to print these steps or view them in another browser.
#Download the latest Desktop version of Firefox from http://www.mozilla.org and save the setup file to your computer.
#After the download finishes, close all Firefox windows (click Exit from the Firefox or File menu).
#Delete the Firefox installation folder, which is located in one of these locations, by default:
#*'''Windows:'''
#**C:\Program Files\Mozilla Firefox
#**C:\Program Files (x86)\Mozilla Firefox
#*'''Mac:''' Delete Firefox from the Applications folder.
#*'''Linux:''' If you installed Firefox with the distro-based package manager, you should use the same way to uninstall it - see [[Installing Firefox on Linux]]. If you downloaded and installed the binary package from the [http://www.mozilla.org/firefox#desktop Firefox download page], simply remove the folder ''firefox'' in your home directory.
#Now, go ahead and reinstall Firefox:
##Double-click the downloaded installation file and go through the steps of the installation wizard.
##Once the wizard is finished, choose to directly open Firefox after clicking the Finish button.
Please report back to see if this helped you!
* check also if your antivirus or other security software(firewall, antispyware etc) blocks firefox access.
thank you -
My macbook air doesn't start after being for 2 months off? What can i do?
Plug it in and leave it on the charger for about 5 minutes then try to turn it on. If that doesnt work, contact apple and have it sent out for repair or take it to your local apple store. they will probably cover it for free if no physical damage has been done.
-
IMac - Display doesn´t work after restart
My iMac 21 Display doesn´t work after restart. If I turn it off and 1 hour later I want use it again the iMac shows the white screen with the mac logo and then the display goes off. I connected an external display to check if the iMac was ON and with the external display I can login and do everything but the iMac Display doesn´t work .
If I turn it off and wait 3 or 4 hours and then turn it back on the display works OK.
This is very strange behavior I have spent hours and hours trying to fine the solution or a similar issue but nothing so I am looking help here at apple.com
BTW When I bougth the iMac 21 there were some spots over the display so the display was replaced by the provider. The warranty has expired by now.To tell you the truth, I don't know if they have to repalce the LCD panel or what they do for a bad backlight. In this reality of block or assembly replacement it probably involves repalcing the panel and not the backlight component. Don't know what it would cost. You'd have to ask that of a service center.
-
Xorg doesn't start after update
After updating this day (my system was last updated at the beginning of July
this year) I have some problem with Xorg. The server just doesn't start, and
the screen is black. I can get back to the console with Alt-F1.
Here's my Xorg.0.log:
X.Org X Server 1.4.2
Release Date: 11 June 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.25-ARCH i686
Current Operating System: Linux Data 2.6.25-ARCH #1 SMP PREEMPT Mon Jul 14 15:25:51 UTC 2008 i686
Build Date: 21 June 2008 05:47:59PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Aug 5 18:54:03 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "LCD Display"
(**) | |-->Device "SiS"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) Including the default font path /usr/share/fonts/misc,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled,/usr/share/fonts/TTF,/usr/share/fonts/Type1.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(==) RgbPath set to "/usr/share/X11/rgb"
(==) ModulePath set to "/usr/lib/xorg/modules"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81e0a60
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 2.0
X.Org XInput driver : 2.0
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(--) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1039,0630 card 0000,0000 rev 31 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 1039,5513 card 1039,5513 rev d0 class 01,01,80 hdr 80
(II) PCI: 00:01:0: chip 1039,0018 card 0000,0000 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:01:1: chip 1039,0900 card 1043,1455 rev 82 class 02,00,00 hdr 00
(II) PCI: 00:01:2: chip 1039,7001 card 1039,7001 rev 07 class 0c,03,10 hdr 00
(II) PCI: 00:01:3: chip 1039,7001 card 1039,7000 rev 07 class 0c,03,10 hdr 00
(II) PCI: 00:01:4: chip 1039,7018 card 1039,7018 rev 02 class 04,01,00 hdr 00
(II) PCI: 00:01:6: chip 1039,7013 card 1043,1456 rev a0 class 07,03,00 hdr 00
(II) PCI: 00:02:0: chip 1039,0001 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:0a:0: chip 1180,0476 card 1000,0000 rev 80 class 06,07,00 hdr 82
(II) PCI: 00:0a:1: chip 1180,0476 card 1800,0000 rev 80 class 06,07,00 hdr 82
(II) PCI: 01:00:0: chip 1039,6300 card 1043,1452 rev 31 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,6), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:2:0), (0,1,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000a000 - 0x0000afff (0x1000) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xd1800000 - 0xd1ffffff (0x800000) MX[b]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd8000000 - 0xe7efffff (0xff00000) MX[b]
(II) PCI-to-CardBus bridge:
(II) Bus 2: bridge is at (0:10:0), (0,2,5), BCTRL: 0x0580 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[1] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0x24000000 - 0x27ffffff (0x4000000) MX[b]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0x20000000 - 0x23ffffff (0x4000000) MX[b]
(II) PCI-to-CardBus bridge:
(II) Bus 6: bridge is at (0:10:1), (0,6,9), BCTRL: 0x0580 (VGA_EN is cleared)
(II) Bus 6 I/O range:
[0] -1 0 0x00001800 - 0x000018ff (0x100) IX[b]
[1] -1 0 0x00001c00 - 0x00001cff (0x100) IX[b]
(II) Bus 6 non-prefetchable memory range:
[0] -1 0 0x2c000000 - 0x2fffffff (0x4000000) MX[b]
(II) Bus 6 prefetchable memory range:
[0] -1 0 0x28000000 - 0x2bffffff (0x4000000) MX[b]
(--) PCI:*(1:0:0) Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter rev 49, Mem @ 0xd8000000/27, 0xd1800000/17, I/O @ 0xa800/7
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI Memory resource overlap reduced 0xd4000000 from 0xd7ffffff to 0xd3ffffff
(II) Active PCI resource ranges:
[0] -1 0 0xd2000000 - 0xd2000fff (0x1000) MX[b]
[1] -1 0 0xd2800000 - 0xd2800fff (0x1000) MX[b]
[2] -1 0 0xd3000000 - 0xd3000fff (0x1000) MX[b]
[3] -1 0 0xd3800000 - 0xd3800fff (0x1000) MX[b]
[4] -1 0 0xd4000000 - 0xd3ffffff (0x0) MX[b]O
[5] -1 0 0xd1800000 - 0xd181ffff (0x20000) MX[b](B)
[6] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[b](B)
[7] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[8] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[9] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[10] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[b]
[11] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
[12] -1 0 0x0000a800 - 0x0000a87f (0x80) IX[b](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xd2000000 - 0xd2000fff (0x1000) MX[b]
[1] -1 0 0xd2800000 - 0xd2800fff (0x1000) MX[b]
[2] -1 0 0xd3000000 - 0xd3000fff (0x1000) MX[b]
[3] -1 0 0xd3800000 - 0xd3800fff (0x1000) MX[b]
[4] -1 0 0xd4000000 - 0xd3ffffff (0x0) MX[b]O
[5] -1 0 0xd1800000 - 0xd181ffff (0x20000) MX[b](B)
[6] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[b](B)
[7] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[8] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[9] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[10] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[b]
[11] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
[12] -1 0 0x0000a800 - 0x0000a87f (0x80) IX[b](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xd2000000 - 0xd2000fff (0x1000) MX[b]
[5] -1 0 0xd2800000 - 0xd2800fff (0x1000) MX[b]
[6] -1 0 0xd3000000 - 0xd3000fff (0x1000) MX[b]
[7] -1 0 0xd3800000 - 0xd3800fff (0x1000) MX[b]
[8] -1 0 0xd4000000 - 0xd3ffffff (0x0) MX[b]O
[9] -1 0 0xd1800000 - 0xd181ffff (0x20000) MX[b](B)
[10] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[b](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[13] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[14] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[15] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[16] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[b]
[17] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
[18] -1 0 0x0000a800 - 0x0000a87f (0x80) IX[b](B)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded by default.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.4.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "sis"
(II) Loading /usr/lib/xorg/modules/drivers//sis_drv.so
(II) Module sis: vendor="X.Org Foundation"
compiled for 1.4.0.90, module version = 0.9.4
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
Backtrace:
And here's what the server writes out:
Backtrace:
Inconsistency detected by ld.so: dl-open.c: 260: dl_open_worker: \
Assertion `_dl_debug_initialize (0, args->nsid)->r_state == RT_CONSISTENT' failed!
waiting for X server to begin accepting connections
giving up.
xinit: Connection reset by peer (errno 104): unable to connect to X server
xinit: No such process (errno 3): Server error.
Any ideas? Because I have no idea, what is happening.
Edit (08.08.2008): All right, don't bother answering this question anymore. The problem is no longer important. This topic can be closed, since it won't be solved.
(I think it was caused by some error during copying files while updating my system.)
Last edited by TPJ (2008-08-08 08:42:13)sand_man wrote:Is /tmp full?
Damn you're right. The pacman cache filled the disk...
Problem solved - thanks!
Only question left is:What are the correct permissions for /tmp since I'd like to set them back to default.
Last edited by Isildur (2009-08-16 14:22:23) -
Windows 8.1 doesn't start after update. BLACK SCREEN AFTER LOGIN
Before all, sorry my english, I'm brazilian and don't found the solution on the brazilian version of HP website.
After I did the updates, the system ask to restart the notebook, so I did it. And now, when I do the login, after the password page, the Windows doesn't starts. Just a Black Screen appears.
I can't open the right side window to acces the configurations, and this laptop doesn't have a battery to take out and put in again.
I had already restore the system.
So, I use my laptop to work, and it has only 4 days of use.
I need help! Thanks!Hi,
Run through the following procedure.
Boot the computer normally and log-in.
At the black screen, hold down the ctrl and alt keys and press delete.
Select Task Manager.
Click on File and select Run new task.
Type cmd.exe - also enter a tick in the box for 'Create this task with administrative privileges' - and click Ok.
Type in the following command ( including spaces ) and hit enter.
Dism /Online /Cleanup-Image /RestoreHealth
This will take a while to complete, but when it’s finished, restart the notebook.
If the screen is still black after you log-in, once again, hold down the ctrl and alt keys and press delete.
Select Task Manager.
Click on File and select Run new task.
Type cmd.exe - also enter a tick in the box for 'Create this task with administrative privileges' - and click Ok.
Type in the following command ( there's a space between sfc and the / ) and hit enter.
Sfc /scannow
When the scan has finished, check that the result is ‘No integrity violations’, then type exit and hit enter.
Restart the notebook again.
Any change?
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Mac OS X 10.4.8 doesn't start after upgrade to 10.4.10
Hi everybody!
I've upgraded my Mac OS X 10.4.8 to 10.4.10 and after restart it doesn't start anymore I also have BootCamp installed and Windows boots now even if I choose to start Mac OS. I've tried boot it in safe and verbose mode but computer boots Windows instead (
How could I run Mac OS? Maybe it's possible to return to the "before update" state?
Thanks in advance!To return to the before state you need to boot from your Tiger installer disk. Run Disk Utilities and Repair Disk. Then choose to do an Archive & Install.
-
VMWare doesn't start after kernel update
Hello,
I've just updated my kernel to 3.10.0-997-generic. After that VMWare Player doesn't start anymore.
I've tried to run patches and different solutions I found in google, but it didn't worked yet.
This is the log of my last attempt.
Thanks in advance
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Log for VMware Workstation pid=14806 version=9.0.2 build=build-1031769 option=Release
2013-06-14T21:42:29.306-03:00| vthread-3| I120: The process is 64-bit.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Host codepage=UTF-8 encoding=UTF-8
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Host is Linux 3.10.0-997-generic Ubuntu 12.10
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Msg_Reset:
2013-06-14T21:42:29.306-03:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/usr/lib/vmware/settings": No such file or directory.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: ----------------------------------------
2013-06-14T21:42:29.306-03:00| vthread-3| I120: PREF Optional preferences file not found at /usr/lib/vmware/settings. Using default values.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Msg_Reset:
2013-06-14T21:42:29.306-03:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/config": No such file or directory.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: ----------------------------------------
2013-06-14T21:42:29.306-03:00| vthread-3| I120: PREF Optional preferences file not found at /root/.vmware/config. Using default values.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: Msg_Reset:
2013-06-14T21:42:29.306-03:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/preferences": No such file or directory.
2013-06-14T21:42:29.306-03:00| vthread-3| I120: ----------------------------------------
2013-06-14T21:42:29.306-03:00| vthread-3| I120: PREF Failed to load user preferences.
2013-06-14T21:42:29.306-03:00| vthread-3| W110: Logging to /tmp/vmware-root/vmware-modconfig-14806.log
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Reading in info for the vmmon module.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Reading in info for the vmnet module.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Reading in info for the vmblock module.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Reading in info for the vmci module.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Reading in info for the vsock module.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Setting vsock to depend on vmci.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Created new pathsHash.
2013-06-14T21:42:29.318-03:00| vthread-3| I120: Invoking modinfo on "vmmon".
2013-06-14T21:42:29.320-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 0.
2013-06-14T21:42:29.320-03:00| vthread-3| I120: Invoking modinfo on "vmnet".
2013-06-14T21:42:29.322-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:29.322-03:00| vthread-3| I120: Invoking modinfo on "vmblock".
2013-06-14T21:42:29.324-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:29.324-03:00| vthread-3| I120: Invoking modinfo on "vmci".
2013-06-14T21:42:29.326-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:29.326-03:00| vthread-3| I120: Invoking modinfo on "vsock".
2013-06-14T21:42:29.328-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 0.
2013-06-14T21:42:29.345-03:00| vthread-3| I120: Obtaining info using the running kernel.
2013-06-14T21:42:29.345-03:00| vthread-3| I120: Setting header path for 3.10.0-997-generic to "/lib/modules/3.10.0-997-generic/build/include".
2013-06-14T21:42:29.345-03:00| vthread-3| I120: Validating path "/lib/modules/3.10.0-997-generic/build/include" for kernel release "3.10.0-997-generic".
2013-06-14T21:42:29.351-03:00| vthread-3| I120: Preprocessed UTS_RELEASE, got value "3.10.0-997-generic".
2013-06-14T21:42:29.351-03:00| vthread-3| I120: The header path "/lib/modules/3.10.0-997-generic/build/include" for the kernel "3.10.0-997-generic" is valid. Whoohoo!
2013-06-14T21:42:29.517-03:00| vthread-3| I120: Kernel header path retrieved from FileEntry: /lib/modules/3.10.0-997-generic/build/include
2013-06-14T21:42:29.517-03:00| vthread-3| I120: Update kernel header path to /lib/modules/3.10.0-997-generic/build/include
2013-06-14T21:42:29.517-03:00| vthread-3| I120: Validating path "/lib/modules/3.10.0-997-generic/build/include" for kernel release "3.10.0-997-generic".
2013-06-14T21:42:29.523-03:00| vthread-3| I120: Preprocessed UTS_RELEASE, got value "3.10.0-997-generic".
2013-06-14T21:42:29.523-03:00| vthread-3| I120: The header path "/lib/modules/3.10.0-997-generic/build/include" for the kernel "3.10.0-997-generic" is valid. Whoohoo!
2013-06-14T21:42:29.524-03:00| vthread-3| I120: Found compiler at "/usr/bin/gcc"
2013-06-14T21:42:29.526-03:00| vthread-3| I120: Got gcc version "4.7".
2013-06-14T21:42:29.526-03:00| vthread-3| I120: GCC minor version 4 does not match Kernel GCC minor version 4. But that is ok.
2013-06-14T21:42:29.526-03:00| vthread-3| I120: Using user supplied compiler "/usr/bin/gcc".
2013-06-14T21:42:29.528-03:00| vthread-3| I120: Got gcc version "4.7".
2013-06-14T21:42:29.528-03:00| vthread-3| I120: GCC minor version 4 does not match Kernel GCC minor version 4. But that is ok.
2013-06-14T21:42:29.532-03:00| vthread-3| I120: Trying to find a suitable PBM set for kernel "3.10.0-997-generic".
2013-06-14T21:42:29.532-03:00| vthread-3| I120: No matching PBM set was found for kernel "3.10.0-997-generic".
2013-06-14T21:42:29.532-03:00| vthread-3| I120: Validating path "/lib/modules/3.10.0-997-generic/build/include" for kernel release "3.10.0-997-generic".
2013-06-14T21:42:29.538-03:00| vthread-3| I120: Preprocessed UTS_RELEASE, got value "3.10.0-997-generic".
2013-06-14T21:42:29.538-03:00| vthread-3| I120: The header path "/lib/modules/3.10.0-997-generic/build/include" for the kernel "3.10.0-997-generic" is valid. Whoohoo!
2013-06-14T21:42:29.538-03:00| vthread-3| I120: GCC minor version 4 does not match Kernel GCC minor version 4. But that is ok.
2013-06-14T21:42:29.539-03:00| vthread-3| I120: Validating path "/lib/modules/3.10.0-997-generic/build/include" for kernel release "3.10.0-997-generic".
2013-06-14T21:42:29.545-03:00| vthread-3| I120: Preprocessed UTS_RELEASE, got value "3.10.0-997-generic".
2013-06-14T21:42:29.545-03:00| vthread-3| I120: The header path "/lib/modules/3.10.0-997-generic/build/include" for the kernel "3.10.0-997-generic" is valid. Whoohoo!
2013-06-14T21:42:29.545-03:00| vthread-3| I120: GCC minor version 4 does not match Kernel GCC minor version 4. But that is ok.
2013-06-14T21:42:29.545-03:00| vthread-3| I120: Using temp dir "/tmp".
2013-06-14T21:42:29.547-03:00| vthread-3| I120: Invoking modinfo on "vmnet".
2013-06-14T21:42:29.548-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:29.548-03:00| vthread-3| I120: Invoking modinfo on "vmblock".
2013-06-14T21:42:29.550-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:29.550-03:00| vthread-3| I120: Invoking modinfo on "vmci".
2013-06-14T21:42:29.552-03:00| vthread-3| I120: "/sbin/modinfo" exited with status 256.
2013-06-14T21:42:30.327-03:00| vthread-3| I120: Setting destination path for vmnet to "/lib/modules/3.10.0-997-generic/misc/vmnet.ko".
2013-06-14T21:42:30.327-03:00| vthread-3| I120: Extracting the vmnet source from "/usr/lib/vmware/modules/source/vmnet.tar".
2013-06-14T21:42:30.332-03:00| vthread-3| I120: Successfully extracted the vmnet source.
2013-06-14T21:42:30.332-03:00| vthread-3| I120: Building module with command "/usr/bin/make -j8 -C /tmp/modconfig-YkpUyf/vmnet-only auto-build HEADER_DIR=/lib/modules/3.10.0-997-generic/build/include CC=/usr/bin/gcc IS_GCC_3=no"
2013-06-14T21:42:31.977-03:00| vthread-3| W110: Failed to build vmnet. Failed to execute the build command.
2013-06-14T21:42:31.979-03:00| vthread-3| I120: Setting destination path for vmblock to "/lib/modules/3.10.0-997-generic/misc/vmblock.ko".
2013-06-14T21:42:31.979-03:00| vthread-3| I120: Extracting the vmblock source from "/usr/lib/vmware/modules/source/vmblock.tar".
2013-06-14T21:42:31.990-03:00| vthread-3| I120: Successfully extracted the vmblock source.
2013-06-14T21:42:31.990-03:00| vthread-3| I120: Building module with command "/usr/bin/make -j8 -C /tmp/modconfig-YkpUyf/vmblock-only auto-build HEADER_DIR=/lib/modules/3.10.0-997-generic/build/include CC=/usr/bin/gcc IS_GCC_3=no"
2013-06-14T21:42:33.429-03:00| vthread-3| W110: Failed to build vmblock. Failed to execute the build command.
2013-06-14T21:42:33.431-03:00| vthread-3| I120: Setting destination path for vmci to "/lib/modules/3.10.0-997-generic/misc/vmci.ko".
2013-06-14T21:42:33.431-03:00| vthread-3| I120: Extracting the vmci source from "/usr/lib/vmware/modules/source/vmci.tar".
2013-06-14T21:42:33.445-03:00| vthread-3| I120: Successfully extracted the vmci source.
2013-06-14T21:42:33.446-03:00| vthread-3| I120: Building module with command "/usr/bin/make -j8 -C /tmp/modconfig-YkpUyf/vmci-only auto-build HEADER_DIR=/lib/modules/3.10.0-997-generic/build/include CC=/usr/bin/gcc IS_GCC_3=no"
2013-06-14T21:42:35.773-03:00| vthread-3| I120: Successfully built vmci. Module is currently at "/tmp/modconfig-YkpUyf/vmci.o".
2013-06-14T21:42:35.773-03:00| vthread-3| I120: Found the vmci symvers file at "/tmp/modconfig-YkpUyf/vmci-only/Module.symvers".
2013-06-14T21:42:35.774-03:00| vthread-3| I120: Installing vmci from /tmp/modconfig-YkpUyf/vmci.o to /lib/modules/3.10.0-997-generic/misc/vmci.ko.
2013-06-14T21:42:35.774-03:00| vthread-3| I120: Registering file "/lib/modules/3.10.0-997-generic/misc/vmci.ko".
2013-06-14T21:42:36.234-03:00| vthread-3| I120: "/usr/lib/vmware-installer/2.1.0/vmware-installer" exited with status 0.
2013-06-14T21:42:36.234-03:00| vthread-3| I120: Registering file "/usr/lib/vmware/symvers/vmci-3.10.0-997-generic".
2013-06-14T21:42:36.686-03:00| vthread-3| I120: "/usr/lib/vmware-installer/2.1.0/vmware-installer" exited with status 0.Before
create file "/usr/lib/vmware/settings"
after
create file "/root/.vmware/config"
after
create file "/root/.vmware/preferences"
And after
Install the build-essential package:
sudo apt-get install build-essential
VMware Workstation 11.1.0 and Player (Pro) 7.1.0 support kernels up to 3.18. You can apply a patch:
curl http://pastie.org/pastes/9934018/download -o /tmp/vmnet-3.19.patch
cd /usr/lib/vmware/modules/source
tar -xf vmnet.tar
patch -p0 -i /tmp/vmnet-3.19.patch
tar -cf vmnet.tar vmnet-only
rm -r *-only
vmware-modconfig --console --install-all
I tried, worked -
Server doesn't start after applying SP3
Hi,
after applying SP3 the server doesn't start.
I just get the following error within the server log.
Any hints ?
Regards
Gerald Eder
JVMX version - May 20 2007 23:27:34 - 01_REL - optU - windows amd64 - bas2:78002 (mixed mode, sharing)
(CompilerOracle exclude com/sapportals/portal/pb/layout/taglib/ContainerTag addIviewResources)
(CompilerOracle exclude com/sap/engine/services/keystore/impl/security/CodeBasedSecurityConnector getApplicationDomain)
(CompilerOracle exclude com/sap/engine/services/rmi_p4/P4StubSkeletonGenerator generateStub)
(CompilerOracle exclude com/sapportals/portal/prt/util/StringUtils escapeToJS)
(CompilerOracle exclude com/sapportals/portal/prt/core/broker/PortalServiceItem startServices)
(CompilerOracle exclude com/sap/engine/services/webservices/server/deploy/WSConfigurationHandler downloadFile)
(CompilerOracle exclude com/sapportals/portal/prt/jndisupport/util/AbstractHierarchicalContext lookup)
(CompilerOracle exclude com/sapportals/portal/navigation/cache/CacheNavigationNode getAttributeValue)
(CompilerOracle exclude com/sapportals/portal/navigation/TopLevelNavigationiView PrintNode)
(CompilerOracle exclude com/sapportals/wcm/service/ice/wcm/ICEPropertiesCoder encode)
(CompilerOracle exclude com/sap/lcr/pers/delta/importing/ObjectLoader loadObjects)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readElement)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readSequence)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/TypeMappingImpl initializeRelations)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/GeneratedComplexType _loadInto)
(CompilerOracle exclude com/sap/lcr/pers/delta/importing/ObjectLoader loadObjects)
The active factory is : com.sap.engine.boot.loader.StandardClassLoaderFactory
Using an index file : D:\usr\sap\TC1\J20\j2ee\cluster\bin\index.list
[GC [ParNew: 14592K->4114K(29120K), 0.0102761 secs] 14592K->4114K(116544K), 0.0103466 secs]
Reading kernel properties from kernelProperties.bin file...
Checked the data for 32 ms.
Read the objects for 250 ms.
Substituted the values for 47 ms.
Finished reading kernel objects for 297 ms.
StartupFramework returned mode [NORMAL]
StartupFramework returned action [NONE]
SAP J2EE Engine Version 7.10.3301.162847.20070927153007 is starting...
Loading: LogManager ... 578 ms.
Loading: PoolManager ... 0 ms.
Loading: ApplicationThreadManager ... Error - ID:000004. System is halted. Exception is:
java.lang.NoClassDefFoundError: com/sap/jvm/Capabilities
at com.sap.engine.core.thread.impl3.ErrorQueueHandler.<clinit>(ErrorQueueHandler.java:34)
at com.sap.engine.core.thread.impl3.ThreadManagerImpl.init(ThreadManagerImpl.java:204)
at com.sap.engine.core.Framework.loadSingleManager(Framework.java:665)
at com.sap.engine.core.Framework.loadManagers(Framework.java:367)
at com.sap.engine.core.Framework.start(Framework.java:296)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at com.sap.engine.boot.FrameThread.startFramework(FrameThread.java:161)
at com.sap.engine.boot.FrameThread.run(FrameThread.java:183)
at com.sap.engine.boot.StartFrame.work(StartFrame.java:101)
at com.sap.engine.boot.Start.main(Start.java:33)
Caused by: java.lang.ClassNotFoundException: com.sap.jvm.Capabilities
Loader Info -
ClassLoader name: [system:Kernel]
Living status: alive
Direct parent loaders:
[library:core_lib]
Resources:
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\jenqulib.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcantlr~runtime.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcachemgmtapi_for_assembly.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcachemgmtimpl.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcache_pluginslib.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblframekrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_cacheimpl.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_classloadkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_clusterkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_configurationkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_databasekrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_licensingkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_lockingkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_logkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_poolkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_servicekrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_threadkrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblopensqlkernelimplOpenSQLKrn.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcjeoffline_deployimpl.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcjesessionmgmtimpl.jar
D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcseclikeylikey_assembly.jar
at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:259)
at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:228)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:353)
... 13 moreAfter upgrading the SAPVM the server starts
Maybe you are looking for
-
How to create a data load file from Excel !!!
Hi All, I'm new to HFM and would like to load data into an HFM application. As I have an Excel file with all the data. When I'm directly loading the data it throws an error saying "No section has been specified to determine if this is data, descripti
-
Where is Adobe's Flash Player Update reminder hiding?
within a flash click the opposite mouse button and you may change some Adobe flash settings like allowing camera and microphone access. but once you've done that Adobe dumps a kind of version checker on your system. you'll see that after the next boo
-
Sales area missing after Product download --ECC to CRM
Dear SDN team, Im facing a issue after downloading few products from ECC to CRM using Middleware . The Products have been download successfully , but the Sales area for Product is missing in CRM system . I have correctly mapped the ECC sales area to
-
hey, i have been reading around this site a. Is there no live chat at all for support or sales to discuss the best solution?? anyway.. i need some help making the right choice and setup with skype for my small business. There is two employees current
-
Dear all, I didn't work on JSP with JSTL. If anyone can help me in this regard for making a simple JSP page with JSTL, it will be highly appreciable. I am working on Tomcat 5.0. Thanks for ur time