IMac G5 Goes to Darwin Prompt after User Password is Entered at Login! Help

I have just made a fresh installation of the Mac OSX in my iMac G5 after some problems of its repeated powering off. It worked fine after the re-installation but when I tried to boot it up the morning after and after logging in on the start-up page, it took me to a prompt again asking for a user name and password. After Darwin identifies me, I expected it to boot up but it does'nt and keeps me on a prompt. Please help! I am a layman and I do not know these things. Any help will be appreciated. Thank you.

Sarbit, welcome to the discussions!
I had my midplane and PSU replaced back last August and have not seen anything that would make me believe that I will have a recurrence of the problem. Fortunately, if I do I am still covered for another year under the warrantee extension, as are you.

Similar Messages

  • Macbook Pro boots to Darwin prompt after update

    I updated my Macbook Pro using Auto Update this morning, and now I can only boot to a Darwin prompt. The computer would boot, go to the starting OS X screen, then straight to the prompt. If I exited the prompt, I would be taken to a user login screen (which would revert back to the prompt after an attempted login)
    I checked the system log and it showed that SecurityAgent was crashing.
    So, per the advice in this post:
    http://discussions.apple.com/message.jspa?messageID=1545778#1545778
    I renamed the NetInfo Database, and reran the initial setup using the proper account short name.
    However, now the computer goes to the gray timer circle before straight to the prompt, no Starting OS X screen.
    The system log now shows the following:
    loginwindow[66]: Login Window Started Security Agent
    loginwindow[66]: AuthorizationRef doesn't have a username (<LoginAuthRefMgr: 0x336150>).\n
    launchd: onoption repeating too quickly on port /dev/console, sleeping
    I thought flushing the NetInfo Database would help, but apparently not.
    I would appreciate any help, and thanks!

    I am having the exact same issue!!!! The problem started as soon as I updated to 10.5.4. I sent my computer off to Apple's Depot to be fixed. The 6 day turn around really slowed me down. After my MacBook Pro was returned I had a note from Service that my Logic Board was replaced and my 3rd Party RAM was not 'Apple Friendly.' The RAM is fine and in Perfect Working Condition. I am assuming that after the Apple Techs got to my RAM they did not proceed to replace my Graphics Card or the Inverter Board (the small cable that sends power to the monitor). I took my MacBook Pro out of the box, re-inserted my 3rd-Party RAM and the computer worked fine for 3 weeks. That's until Last Night I had a FireWire Drive Mounting issue and had to Hard Re-Start my system it was then that the Black Screen Issue started again. Again, your notes are EXACTLY the same issue I am now having! I have called Apple Support and they will now take my computer to service with 'White Glove Treatment.'
    After reading your post I am convinced that this is a software Bug. Apple please update. As of now I cannot even startup my computer to check for updates! Also, I cannot afford to be without my system for another week!!

  • How do I stop iMac from going to sleep automatically after 15minutes of inactivity

    How do I stop imac from shutting down automatically after 15minutes of inactivity, trying to play music but the imac keeps going to sleep, tried changing power saving preferences to never shut down, never go to sleep, unticked put the hard disks to sleep, automatically reduce brightness, but still goes to sleep.

    Try a PRAM/NVRAM reset.
    Resetting NVRAM / PRAM
    Shut down your Mac.
    Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    After resetting NVRAM or PRAM, you may need to reconfigure your settings for speaker volume, screen resolution, startup disk selection, and time zone information. If issues persist, your Mac's logic board battery may need to be replaced. The logic board battery helps retain NVRAM/PRAM settings when your computer is shut down. You can take your Mac to a Mac Genius or Apple Authorized Service Provider to replace the battery on the logic board.

  • When i start up imac it goes through set up creates a new user account then starts over againj, when i start up imac it goes through set up create user account then starts over again over and over

    when i start imac it goes through set up gets to creating new user account then it re boots and does it all  again and again and again

    Apple may still supply the original restore CDs/DVDs for a nominal fee.  Have a your serial number and model information available when you call them.
    AppleCare Support Phone Number: 1-800-275-2273
    open 6am to 6pm Pacific Time
    Apple Phone Sales 1-800-692-7753
    International Technical Support Numbers
    http://www.apple.com/support/contact/phone_contacts.html
    "You have to call Apple & likely ask for a Product Specialist to get it (Leopard), if they still have it... helps if you tell them you have a new iPhone (iPad) that needs it!"
    BDAqua
    Requirements for Mac OS X v10.5
    http://support.apple.com/kb/HT3759
    Query by serial number "A serial number is a unique, identifying number or group of numbers and letters assigned to an individual piece of hardware or software. It's used for various things depending on the product / brand but what is your Mac's serial number for and more importantly... what is it hiding and what can it do for you ?"
    http://www.appleserialnumberinfo.com/Desktop/index.php or

  • MS OUTLOOK PROMPT USERNAME AND PASSWORD REPEATLY WHEN WE LOGIN WINDOWS 8.1 WITH DOMAIN USER ON WINDOWS SERVER 2008R2

    Dear Sir
       My name is sandeep and i have a technical issue with MS office Outlook 2007 standard. the problem is i have windows 8.1 pro. and i have installed office 2007 standard on it. i have also joined this windows 8.1  to Domain Network(I have
    domain Server on Windows server 2008R2) now problem is that when i login with domain user on this windows 8.1 and configure my MS outlook the it prompts user name and password again and again showing error "
    Server responded -ERR access denied"  and if i login windows 8.1 with its local administrator user the all runs file then ms outlook does
    not prompt for username and password. this problem with only windows 8.1 domain login.. please suggest what to do and how this problem will be resolved..
    Regards
    sandeep Kumar

    Hi,
    Did it work correctly before when logging in with domain user account? If so, please try opening Control Panel > Credential Manager and remove the cached credential entry of the Outlook account, and then restart Outlook to test the issue again.
    See:
    https://support.microsoft.com/en-us/kb/2762344/en-us
    Please also try logging into your email account from webmail access to see if there is any error.
    Please let me know the result.
    Regards,
    Steve Fan
    TechNet Community Support
    It's recommended to download and install
    Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
    programs.
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • I just buy a imac 27inch when after intalling everthing for windows 7 and all the drivers i need and goes to the restard part my imac just goes to a black screen with a blinking cursel and it just wont proceed anyone can help me with this?

    i just buy a imac 27inch when after intalling everthing for windows 7 and all the drivers i need and goes to the restard part my imac just goes to a black screen with a blinking cursel and it just wont proceed anyone can help me with this?

    Support articles for things like this would be here:
    http://www.apple.com/support/bootcamp

  • CR prompts for user credentials after refresh even though I'm using SSO

    Hello Experts,
    We have a problem with a customeru2019s project concerning Crystal Reportu2019s Single Sign On feature:
    Even though weu2019re using SSO, Crystal Reports prompts for user credentials every time a refresh is performed manually in the browser.
    We already checked SAP note [1214594 - How to avoid database login prompts when refreshing reports in Crystal Reports|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap%28bd1lbizjptawmq==%29/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333233313334333533393334%7D.do]. The note suggests using Microsoft Windows authentication (trusted connection or operating system authentication) u2013 unfortunately we cannot use this kind of authentication in our project.
    Do you have any hint, idea or suggestions?
    Thank you in advance!

    Hello,
    What kind of Project are you developing? Search for Post Back in the SDK forum and Kbase system so you can keep the log on token active. Likely what is happening is the Token or connection times out after 20 minutes, which is IIS's default timeout. Using the postback method is one way of keeping the SSO connection active.
    Thank you
    Don

  • Mac OS X 10.6.8 desktop goes black 10 secs after booting, can remain apparently asleep for 15 mins. I can't prompt it to wake, until recently it would wake when peripheral were added (earphones). What is wrong, and how can this be fixed?

    Mac OS X 10.6.8 statup problem: desktop goes black 10 secs after booting, can remain apparently asleep for 15 mins. I can't prompt it to wake, until recently it would wake when peripheral were added (earphones). What is wrong, and how can this be fixed?

    You need to fresh install 10.6, programs fresh form original sources and return only vetted files (no TM migrations) from a regular storage drive
    But this when erasing the drive use the Security Option: Zero All Data before installing 10.6
    What has happened your data got corrupted and it's corrupted on the TM drive too.
    So the Zero will map off bad sectors on your drive, the 10.6 install will be fresh, the programs will be fresh and only files will be returned, you'll find out in short order which ones they are.
    Reducing bad sectors effect on hard drives
    How to erase and install Snow Leopard 10.6
    Once you are back up, then consider making a option key bootable clone.
    Most commonly used backup methods explained

  • HT1386 every time I try to sync my phone and restore my content after I updated my iPhone, iTunes goes through the prompts and then says "cancelling sync" at step 5.  I cannot restore my apps or music!

    every time I try to sync my phone and restore my content after I updated my iPhone, iTunes goes through the prompts and then says "cancelling sync" at step 5.  I cannot restore my apps or music!

    when i try to sync my music which i have on my PC's itunes it will just not transfere on the phone. everything will sync [apps, videos, contacts] but the music will just not transfere.
    and when i try to download the music from the phone's itunes store it will say "Error. Tap again to retry".
    Thera are no more details i have! i have no idea why the songs will not sync and will not download!

  • My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked?

    My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, I call apple support and they told me to bring it in but the nearest store is about two hours away. They said I need it to erase my hard drive but I have too many family pics on it.
    would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked on it? I could replace the internal and get an enclosure for the original until I get the pics out of it?
    Please advise, it's like five years of family pics I don't wanna loose them and I am worried.
    Thanks
    Al Florez

    A Brody,
    I really apprecate your very quick respond, Its too late to back up as of now, my hard drive wont load at all so I cannot follow your instruction to back it up. Learn a hard lesson but I will from now on following your link.
    Also my hard drive it is not available to do the free exchange program.
    I read the OWC instruction on how to replace the drive I was just wondering if the 2TB would work on it instead of the 1 TB they offer, I specifically asked for the Seage Barracuda because I had great experiences with it on PCs.
    Again, Thank you

  • The screen of my imac always goes to the maximum exposure. Then the light icon on the screen. After reducing the brightness goes my screen after a few minutes back to the maximum intensity with the brightness icon back on my TV screen.

    The screen of my imac always goes to the maximum exposure. Then appear the light icon on the screen. After reducing the brightness goes my screen after a few minutes back to the maximum intensity with the brightness icon back on my screen.

    Try resetting the SMC and if that doesn't work then reset the PRAM too.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • Safari in ipad prompts the location every time even after User accepts it.

    We developed an application which uses HTML5 geo location to track down the user's location. When the application is launched, safari prompts the user asking for the permission whether the current location can be used or not. This happens for two times continuously as per apple documentation.
    However for the given application, it happens more frequently even after user accepting to share the location.
    Safari prompts it whenever user moves to NEW location.
    Is this a known issue? Is there any workaround for this??
    Also please let us know if there is a documentation which describes the problem with the location prompt in more detail?
    Thanks

    I’ve just started an almost identical thread: Recurring geolocation prompts on iOS.
    Did you figure this out?

  • Open Directory users prompted to change password after 10.8 to 10.9 server upgrade

    I just upgraded our 10.8.5 server to 10.9.3. I also upgraded Server.app to the most recent version (3.1.2). I made a complete backup first as a precaution.
    Existing non-admin users are being prompted to change their password when logging in. I've narrowed the problem down to a checkbox in the "Global Password Policy" settings in Server.app, specifically this checkbox: "Passwords must: be reset on first user login". I had that box checked in 10.8 so that new users would be prompted to create a password the first time they logged into a bound computer. It worked great and I'd like to continue using this feature in 10.9.
    If I uncheck this box in Server.app in 10.9.3, existing users can log in just fine with their existing passwords. If I re-check the box, non-admin users are suddenly prompted to change their password when logging in, even though they've logged in countless times in the past.
    Here are some things I've tried:
    * stopping and restarting the Open Directory service in Server.app
    * restarting the server
    * disabling and re-enabling an existing user account
    * inspecting user records in Directory Utility for any peculiar attributes
    * I used the mkpassdb -dump command to verify that the correct "last login time" is present for a particular user, but I'm not enough of an Open Directory expert to know if this is the attribute that the Global Password Policy relies on.
    Does anyone have any other ideas or suggestions?

    UPDATE: It looks like this issue applies to new (post-upgrade) accounts, too, suggesting that this has nothing to do with the upgrade process. Can anyone confirm this behavior? It's easy to test:
    1) Make sure the "Passwords must: be reset on first user login" box is unchecked.
    2) Create a new user in Open Directory.
    3) Log in once. No problem.
    4) Now check the "Passwords must: be reset on first user login" box.
    5) Try to log in again. Were you prompted to change your password? Logically, you shouldn't have been prompted, but users on my server are being prompted.

  • Acrobat 7 freezes after cancelling the user password prompt

    I'm having a problem with Acrobat 7.1 when downloading a password-protected PDF from a website.  The problem occurs at the "please enter a document open password" dialog box.  If I enter the user password, the PDF opens successfully.  However, if I click Cancel instead of entering the password, Acrobat hangs/freezes in the background (visible in the Task Manager) and the CPU spikes to 50%.  At that point, opening another PDF freezes Internet Explorer since it's still waiting on the Acrobat process hanging in the background.  I've tested on both Windows XP and Windows Server 2003 with the same result.  The problem appears to be resolved in Acrobat 9, but unfortunately my users are stuck on Acrobat 7.1 for the time being.  Any help would be greatly appreciated!

    As Baltwo said, you should have a password set on your computer for secutity reasons. You can set it to automatically log you on if you are the only user when starting up and you don't need to input the password.
    What Baltwo was getting to was to make sure nothing was in the field such as a space. Apparantly, it won't let you log into it without a password.
    I seem to remember a default password in past systems. I think it was computer. Try typing that in. If it doesn't work, then follow the steps in this article and set a password for your user account.
    http://osxdaily.com/2011/08/24/reset-mac-os-x-10-7-lion-password/

  • IMac 7,1 boot only in single user mode

    Hi all
    I've a colleague with the following problem... his iMac 20'' (iMac7,1) is able to boot ONLY in safe/single user mode (with shift key pressed during boot).
    If he tries to boot normally, after the usual Apple logo screen he gets a blank (light grey) screen. No finder, no login screen.
    We've tried this procedures:
    - SMB reset
    - PRAM cleared
    - OS Reinstall (we've tried from Lion to Mavericks... actually there's 10.7.5 installed)... note that ALL installation procedure has completed successfully.
    - tested the 1 RAM module installed (seems to be OK)
    - tested the HD (no problems found)
    Despite all these attempts, this iMac is booting well only if we press SHIFT during startup. All programs run well, wifi is working and online update too. If we reboot leaving it to restart normally (no key pressed) it shows Apple Logo for 1 minutes, then (after a black reset of the screen) seems to crash/stuck into an empty grey screen.
    Is possible to identify which driver/kext is causing this problem? It can be an hardware problem? How we can fix it?
    Thank you!

    1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
    Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
    2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
    There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
    3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
    You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
    In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
    You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
    Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
    4. Here's a summary of what you need to do, if you choose to proceed:
    ☞ Copy a line of text in this window to the Clipboard.
    ☞ Paste into the window of another application.
    ☞ Wait for the test to run. It usually takes a few minutes.
    ☞ Paste the results, which will have been copied automatically, back into a reply on this page.
    The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
    5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
    6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
    7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
    Triple-click anywhere in the line of text below on this page to select it:
    PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.apple.AirPortBaseStationAgent com.apple.installer.osmessagetracing com.apple.SafariNotificationAgent com.apple.usbmuxd com.apple.xprotectupdater com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper ' ' 879294308 3627668074 1083382502 1274181950 1855907737 464843899 1233118628 2636415542 842973933 4019080058 3301885676 891055588 998894468 695903914 1443423563 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { split("'"${p[41]}"'",b);for(i in b) print b[i];if(n<10) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { split("'"${p[41]}"'",b);for(i in b) print b[i]".plist";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n   ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */   /;' ' /:/d;/\./p;' '/\.appex\/Contents\/Info\.plist$/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:|suhel| VALI|ver-r|xpma' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" 'L*/P*/com.ap*.p*.ext*.*.*t -exec '"${c1[14]}"' :displayOrder" {} \;' );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors appexes );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 4 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    8. Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
    9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
    exec bash
    and press return. Then paste the script again.
    10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return  three times at the password prompt. Again, the script will still run.
    If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
    11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
    [Process completed]
    to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
    12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
    At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
    If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
    13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
    14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
    Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Maybe you are looking for