IMac LCD screen replaced, Blue Screen startup

Hi there, I just had the LCD screen replaced on my late 2007 Aluminum iMac today (due to a permanent red vertical streak) by an Applecare certified technician. He did a meticulous job with the replacement, and the iMac booted up just fine afterwards. About an hour later, though, I tried starting up the iMac and after the grey screen with the Apple logo it gets stuck on a blue screen with a constantly spinning pinwheel.
Now I tried everything, booting up in Safe Mode, Single User Mode, resetting the PRAM, FSCK, Disk Utility using Disk Repair, unplugging the power cord for 30 seconds, etc. and nothing seems to work. It just gets stuck on a blue screen whenever it tries to boot up.
Just wanted to see if there is anything else I could try out before I give Apple a call tomorrow, if this boot up problem is a result of the new LCD screen replacement or what? Any help or insight in the matter would be greatly appreciated, thanks.
Update: I should note that right now I'm in the (lengthy) process of restoring from a Time Machine save to see if that helps out in any way.

You could try the following first, but a repair may be required.
iMac G5: Fails to startup (From an article at MacFixit)
Some users are reporting an issue where iMac G5s fail to properly startup -- apparently at a hardware level -- never reaching the Mac OS X startup splash screen (Apple logo with a spinning progress indicator).
Note that in cases where the system does reach the Mac OS X startup splash screen or further progression but stalls, software issues may be to blame.
Potential fixes
Disconnect external devices External devices -- especially those that draw power from the system -- can cause issues with startup that manifest either at the beginning of or later in the boot process. Try temporarily any external FireWire or USB devices then re-attempt startup and check for persistence of the issue.
Reset SMU Although this workaround was not successful in Connors' case, resetting the iMac G5's SMU (system management unit) as described in Apple Knowledge Base article #301733 can resolve a variety of power-related problems, including sudden-onset startup failure.
Check power cables Check your power cord for a loose connection. As noted in the aforementioned reader case, unplugging and re-plugging the power cord can sometimes result in a successful startup -- likely the result of a more snug fit.
Also, power cables can become defective or ship in such a state.
Try exchanging the power cable from a problematic machine with a system that starts up properly to eliminate this as a potential cause.

Similar Messages

Can Motion 5 replace a green screen and blue screen in the same shot?

Can Motion 5 replace a green screen and blue screen in the same shot? I would like to replace a green screen with one image, and a blue screen with another.

Fox gives a good example for keying green & blue (or any other color) from the same shot. I'd suggest doing a few things to get better accuracy.
First, the motion keyer always removes the color it detects the most of by default (blue/green). You can override this by setting the Strength parameter to zero, then use the Color sample tool to select the color you want. The advantage is motion will do a good job of targeting only the hue (color) that you want to remove and set an appropriate starting softness. It also will remove spill based on this color. Looking at Fox's example movie and the shot, I'd approach the same shot this way:
Remove the Blue
1. Apply the keyer and set the strength to zero.
2. Use the Sample Color tool and select the blue (or other color) to be removed.
3. Decrease the spill level (if needed). In Fox's example the spill from the blue glasses is going to be minimal, especially compared to the green screen, your shot may need different adjustments. Only de-spilling what you need to will give you more accurate color right away and minimize additional color correction that might be needed later.
4. Use the Color selection tools (Chroma wheel/Luma bar) to fine tune. Ideally you want a minimal tolerance, the inner selection, with a nice fall off, the outer selection. Try with the Scrub boxes setting first, then switch to manual if you need more control. Again see Fox's example.
Remove Green
It's the same as the blue, you could apply the keyed to the same clip or a parent group, at this point it's many user preference.
With these techniques you can remove any color from a shot or create a mask based on a color. BTW, as you are learning to use the keyer I'd highly recommend having the Color Selection open so you can see the graphs. These give you real time feedback as you make selections and changes with the Strength, Refine and Color selection tools. Watch what happens as you make selection or changes, sometimes the problem area is actually in the brightness not the color, or the softness may change more than the tolerance selection. Observing what is happening in these graphs will help you figure out wha to change and speed things up.

WHAT I DO WHEN THE SCREEN IS BLUE BECAUSE Startup Disk FULL?

WHAT I DO WHEN THE SCREEN IS BLUE BECAUSE Startup Disk FULL?

Have a look to this post : Blue Screen on Startup with MacBook Air Rev A (fitted with Hard Drive)

Grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced 6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen

grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced <6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen. Then tried the other way (sorry, I think it's command alt delete? I don't remember) and it turned from grey (no apple symbol) to blue blank. Then third time, grey followed by blue with vertical lines, not blocky clear lines that you can see if you are close to it.
Thanks for any help!

You have to take the computer to the Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

Blank Black Screen And Blue Screen. Do I Need To Do Reflow To Ati Chipset?

Hello i want to tell you my problems and what i did until now.
I have hp pavilion dv3 4150st. I was using win7 64 bit . and i was geting an error that says "display driver amd driver stopped responding and has successfully recovered".I started to get this eror often . And a few days later my pc startet to get blue screen errcor after a few second later than display driver error. . And after 2-3 blue screen error i lost my screen. It was blank black . when i restart pc the screen was blank black. there was no image. When i started to fix another monitor, i saw screen . And i installed the win 7 with another external monitor. Bu i had still black screen after install the windows.. Itand was still black after i remove the ectgernal monitor. I installed bios again but i had still black screen. And i tried the install ati display driver after installing windows . But after i installed the display driver, i had the blue screen error again. And now i have still both blank black screen and blue screen problem.
I cleaned the motherboard. I resetted bios. I installed bios. i installed windows again. i installed ati display driver.But these couldnt solve the problems. Please can you tell me what can i do now ?

Hi beginner_2012,
Thank you for your post, I will do my best to assist you.
I grasp that you were getting the error "display driver amd driver stopped responding and has successfully recovered" quite often. Then a few days later you got the blue screen then the above error message, after 2 -3 more errors the screen is now blank or black. Here is a document to assist you with this. Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

When i quit safari in full screen a blue screen appears in background

When i close safari in full screen a blue screen appears in mission. What can i do to fix?

Welcome to Apple Communities
Open Finder, press Option key, select Go > Library, open Preferences, delete com.apple.dock.plist, open Terminal and write:
killall Dock

HELP! iMac G5 hangs at blue screen, but boots in Safe Mode

Please can anyone guide me to recover my iMac G5 PowerMac 8,2 running OS X 10.4.11.
Problem; Mac hangs on start-up at blue screen after grey Apple screen. Mouse pointer eventually appears but that is all.
Actions taken so far without success:
1. Disconnected the printer and rebooted - no success.
2. Booted in Safe Mode - first time the screen was completely scrambled but with safe mode log on screen showing through.
2.1 Rebooted in Safe Mode OK This has not occurred again and I have entered Safe Mode twice more without problems. But worrying!
2.2 In Safe Mode I ran disk Utility and verified and repaired Permissions, mostly old EpsonPrinter files.
2.3 I also verified the Disk, which was reported OK.
2.4 I was able to save critical documents to USB............ Phew!
2.5 Reboot in Normal Mode - no success
3. Reset PRAM
3.1 Reboot in Normal Mode - no success
4. Reboot in Safe mode - works fine. NOTE: time and date appear to be correct and dont need resetting.
4.1 Run Disk Utility again and Verify Permissions - OK. Nothing needed fixing.
4.2 Run Disk Verify - Passed OK
4.3 Reboot in Normal Mode - no success. Hangs at blue screen with mouse pointer visible and working. Then pointer vanishes.
I would be most grateful for your help in moving this forward

Got to figure out which which of the things dropped when you boot in safe mode is causing the problem.
see this link:
http://support.apple.com/kb/HT1564?viewlocale=en_US

Boots to windows startup screen, flashes blue screen, restarts and repeats

HP ENVY H8-1414 Product #H3Z00AAR
Windows 7 Ultimate 64-bit
Alright, so here is my issue. I turn on my pc and it gets as far as the windows startup screen, flashes a blue screen error for about half of a second and then restarts it self. My HDD is recognized in the bios. Tried a memory test in diagnostics and it passes. Tried a hard disc check and it passes the SMART check but fails the Long DST with a failure ID of 0GF21L-0006LR-WPVX0K-61C703 (no idea if those a zeros or O's)
I've also tried the startup repair but it did nothing. So I removed the hard drive and tried to use it in a different PC but had the same issue so I figured the hard drive went bad. Then I tried formatting a spare hard drive and installed a fresh copy of windows 7 on it, tried it on a different PC and it works just fine. However, when I try to use that hard drive on the HP ENVY I get the exact same problem even though it worked just fine on a differenct pc.
I purchased this PC refurbished about 3 months ago, the warrenty just ended a week ago. There have been no hardware or software changes on it at all. This thing worked flawlessly last night... I locked the computer before bad and I woke up to this. No power outages over night or anything. It just doesn't make any sense.

Here are the specs for your HP ENVY h8-1414 Desktop Computer. According to the specs, this model came from the factory with Windows 8 installed. The "blue screen" and restart are normal for Windows 7, when it encounters an error, unless you have altered the default settings.
The LONG DST failure is indicative that the hard drive has failed or is about to fail. Unless the hard drive is moved to an identical or very similar computer, Windows will encounter a "blue screen. This is true with the original hard drive moving from the h8 computer to the other computer and the test hard drive from the other other computer moving to the h8 computer.
Try placing the "test" hard drive in the h8 computer and installing Windows 7 from a DVD or USB stick. If you have any problems, please post back with full error messages and screen shots. Also indicate what stage of the install Windows 7 was doing tat the time.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How do I get to normal screen from blue screen on iMac with snow leopard operating system

My iMac boots w white screen and then goes to a blue screen with no icons. I have snow leopard as operating system. I have held command key and r but can't get the repair menu. I have unplugged and tried to reboot. I have checked plugs for keyboard and mouse. Tried to reboot w snow leopard disk. Didn't work. Now can't get disk to eject. System is working because can still use wireless. Any ideas?

Hello, CMD+r only works in Lion/10.7 & up.
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.

IMac G5 Sits on Blue Screen - after showing progress bar

As the title says, my iMac G5 (ALS) has now started to show the first 5% of progress on the loading screen and then stops and sits on the blue screen, with the cursor in the top-left corner. It didn't do this until I disconnected all the cables and re-inserted the power lead.
Back in March, it was sent away for what I thought was Logic Board issues, although the people who I sent it to told me it was the Power Adapter, even though it would still charge my iPod through fiirewire.
So, what should I try? I tried resetting the PRAM, but as I have a bluetooth keyboard, it didn't recognise the buttons I was holding and went back into the blue screen.

Hi. Sorry for only just coming back to this. I've kind of been fed up with the iMac going wrong twice and have been using my iBook G4 instead and kind of forgot about it.
I'll try the SMU later today (it has an internal button on my iMac version [ALS], right?)
Also, the 90 day on repairs. Is that from when I picked it up? If so, that means I have from April 14th to July 14th. If nothing else works, I'll take it to them and they can sort it.
Finally, I have a disc in my drive (Netgear router disc). Is there a way to eject them either internally or through key commands?

Iphone 5S ramdomly restarts, turns off itself, screen shows blue screen sometimes

I am having problem with my iPhone 5S since Tuesday. The phone restarts itself while using like during making calls or surfing internet, the phone turns off automatically and sometimes shows blue screen. I called apple support and they told me to connect my iPhone to iTunes and they had me reset everything like factory resetting and stuff like that. After we did that the phone started working but very next day again I started having same problem, my phone completely turned off by itself and I couldn’t turned it on by pressing power button so I went to apple store at Grand Central made an appointment and I waited there like 45 minutes for my turn. I explained everything and the guy from genius bar he pressed menu button and the power button together and boom… the phone was back on. He checked the phone and says nothing wrong with the phone and I told him everything about the issues. He said if problem happens again come back and we will replace your phone as I recently bought this IPhone and is still under warranty. I came back home and again my phone started acting up…same problem you never know when your phones gonna be turned off….somebody calls you don’t hear nothing funny part is those people who are calling me says phone keeps ringing you don’t pick up. So I made an appointment today I went back to Grand Central apple store, I explained everything today in detail and told them I am using I phone since the time when Iphone 3G came in and I have other iphones too at home and none of them had this kind of problem before. I am really upset with my phone, it's giving me hard time. The guy checked the phone and said phone is working fine nothing wrong with it. Now what I am gonna do? I said please give me replacement phone ‘cause I think there is something wrong with this phone hardware, firmware whatever…He said he can’t, he thinks I am lying. Why should I waste my time going there back and forth after work when you are so tired from your job? Can anyone please suggest what could be the problem?? How to deal with this problem? Thank you
Message was edited by: Topgyal

Call in again and explain the situation. Ask to speak with a supervisor. There are things they can do to document and confirm your issue that way you can get it serviced. Just be sure before returning to the store, you have a case number from the call where they documented to service the device. This process sometimes takes a few days as domes the supervisors need to escalate your information to ensure an outcome in your interest. That would be my recommendation.

Blue screen error /Blue screen of death(Your pc ran into a problem and needs to be restart)

Hello,
About 15 days ago,my laptop is showing blue screen errors,really this is very frustrating.
I use a lenovo laptop,
Processor
Core i3 (3rd Generation)
System Memory
4 GB DDR3
HDD Capacity
320 GB
Operating System
Windows 8
System Architecture
64-bit
Dedicated Graphics Memory Type
DDR3
Dedicated Graphics Memory Capacity
1 GB
Graphic Processor
NVIDIA GeForce 610M
i have tried methods like , 1) un installing the anti virus (Quick Heal Total Security) and re installing again
2)Turning Firewall on and off. Because someon said that this could be a cause of Anti virus..
3)Optiminzing the disk drives...
4)i have used a software called "Blue screen view".which shows all the daetails of blue screen errors
and all dumps files.And also i deleted all the dump files and folder , but also the problem persists.
5)in Google search someone told that to update all the drivers. i have also done that
6)i have uninstalled and reinstalled the graphics driver.
So, i have tried all the methods given online,but i didnt get any help from it.
So please help me . I am tired of all this
*Sorry for poor english

Without the Minidump Files to help us isolate the cause of the errors you are experiencing there is no way to provide assistance specific to your situation.
One of the most common causes of errors are drivers. You have already mentioned that you have upgraded your graphics driver to the latest version provided by the manufacturer, updating other drivers like network, chipset, and storage controllers is a good
next step. If no driver updates resolve your issue and you have already looked into security software as a possible cause, another direction to take would be to review your hardware for possible failures. You can diagnose your memory by
entering “Diagnose your computer’s memory problems” at the start screen and selecting the result. You can also diagnose your storage devices by
right clicking the storage device in File Explorer, selecting properties, and selecting Error Checking.
Brandon
Windows Outreach Team- IT Pro
The Springboard Series on TechNet

Flashes from apple screen to blue screen after latest update.

After I updated last night my phone would never reboot. Goes from screen with apple on it for several minutes then flashes to a blue screen for a second then back to apple screen. I tried hooking up to computer but its like nothing is hooked up. Help!

Hi marston44,
It sounds as if you have experienced an issue with updating the operating system on your iPhone. Let's see if we can get you up and running.
I would suggest that you troubleshoot using the steps in this article -
If you can't update or restore your iPhone, iPad, or iPod touch
Thanks for using Apple Support Communities.
Best,
Brett L

T410 random beep sound( from machine for less than 5 mins) + screen freeze + Blue Screen (some time)

I have new purchased T410 during christmas time.
here is my machine spec(everything from Levono, did not upgrade any parts):
T410, model 2516CTO
8 GB RAM
i7 CPU
500GB HDD
Integried graphic card
Windows 7 professional (applied all latest updates)
Problem random happen, for about 8 times,
System works regularly
and all of sudden machine make continousely "beep" sound(from machine, not speaker),
after that screen freeze,
and then sometime system go back to normal, sometime crash completely to blue screen(most time).
The whole problem takes about 3-5 mins.
1 time it even happen in safe mode (after log in, desktop freezed immediately, then blue screen).
I chkdsk the whole disk found no problem.
I call Lenovo tech support, he ask me restore the original OS(Windows 7 home prim), then he can help me.
I refused because that's mean i have to destroy all the work I done (spend almost a week to install development tools and software) .
Since the problem is random anyway, I just reboot and bakeup more offen. :-(
I used Thinkpad since IBM time, never have problem with previous 2 T Series machines, but this one, not happy.

Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\FreezeIssue\Minidump\010111-51090-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
WARNING: Whitespace at start of path element
Symbol search path is: SRV*C:\Symbols*http://msdl.microsoft.com/download/symbols;
Executable search path is:
Windows 7 Kernel Version 7600 MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Machine Name:
Kernel base = 0xfffff800`02c18000 PsLoadedModuleList = 0xfffff800`02e55e50
Debug session time: Sat Jan 1 14:53:03.162 2011 (GMT-5)
System Uptime: 0 days 0:29:01.004
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
*                        Bugcheck Analysis                                    *
Use !analyze -v to get detailed debugging information.
BugCheck F4, {3, fffffa8008159060, fffffa8008159340, fffff80002f935d0}
Probably caused by : csrss.exe
Followup: MachineOwner
2: kd> !analyze -v
*                        Bugcheck Analysis                                    *
CRITICAL_OBJECT_TERMINATION (f4)
A process or thread crucial to system operation has unexpectedly exited or been
terminated.
Several processes and threads are necessary for the operation of the
system; when they are terminated (for any reason), the system can no
longer function.
Arguments:
Arg1: 0000000000000003, Process
Arg2: fffffa8008159060, Terminating object
Arg3: fffffa8008159340, Process image file name
Arg4: fffff80002f935d0, Explanatory message (ascii)
Debugging Details:
PROCESS_OBJECT: fffffa8008159060
IMAGE_NAME: csrss.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 0
MODULE_NAME: csrss
FAULTING_MODULE: 0000000000000000
PROCESS_NAME: csrss.exe
EXCEPTION_RECORD: fffff8800a977b78 -- (.exr 0xfffff8800a977b78)
ExceptionAddress: 0000000077a8592d
   ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 0000000000000001
   Parameter[1]: 0000000002ea0ef8
Attempt to write to address 0000000002ea0ef8
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
CURRENT_IRQL: 0
ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
EXCEPTION_PARAMETER1: 0000000000000001
EXCEPTION_PARAMETER2: 0000000002ea0ef8
WRITE_ADDRESS: 0000000002ea0ef8
FOLLOWUP_IP:
+0
00000000`77a8592d ??              ???
FAULTING_IP:
+0
00000000`77a8592d ??              ???
FAILED_INSTRUCTION_ADDRESS:
+0
00000000`77a8592d ??              ???
BUGCHECK_STR: 0xF4_C0000005
STACK_TEXT:
fffff880`0a9770f8 fffff800`03014652 : 00000000`000000f4 00000000`00000003 fffffa80`08159060 fffffa80`08159340 : nt!KeBugCheckEx
fffff880`0a977100 fffff800`02fbd3e3 : ffffffff`ffffffff fffffa80`0ab4f060 fffffa80`08159060 fffffa80`08159060 : nt!PspCatchCriticalBreak+0x92
fffff880`0a977140 fffff800`02f4580c : ffffffff`ffffffff 00000000`00000001 fffffa80`08159060 fffff6fb`00000008 : nt! ?? ::NNGAKEGL::`string'+0x17946
fffff880`0a977190 fffff800`02c87993 : fffffa80`08159060 fffff800`c0000005 ffffcbdb`afa4f658 fffffa80`0ab4f060 : nt!NtTerminateProcess+0x20c
fffff880`0a977210 fffff800`02c83f30 : fffff800`02cc2dbc fffff880`0a977b78 fffff880`0a9778e0 fffff880`0a977c20 : nt!KiSystemServiceCopyEnd+0x13
fffff880`0a9773a8 fffff800`02cc2dbc : fffff880`0a977b78 fffff880`0a9778e0 fffff880`0a977c20 00000000`02ea2180 : nt!KiServiceLinkage
fffff880`0a9773b0 fffff800`02c87d82 : fffff880`0a977b78 00000000`000116e4 fffff880`0a977c20 00000000`02ea1c58 : nt!KiDispatchException+0x53b
fffff880`0a977a40 fffff800`02c868fa : 00000000`00000001 00000000`000116e4 fffffa80`079c2201 00000000`77a85a01 : nt!KiExceptionDispatch+0xc2
fffff880`0a977c20 00000000`77a8592d : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x23a
00000000`02ea0f00 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x77a8592d
STACK_COMMAND: kb
FOLLOWUP_NAME: MachineOwner
FAILURE_BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
Followup: MachineOwner
2: kd> !analyze -v
*                        Bugcheck Analysis                                    *
CRITICAL_OBJECT_TERMINATION (f4)
A process or thread crucial to system operation has unexpectedly exited or been
terminated.
Several processes and threads are necessary for the operation of the
system; when they are terminated (for any reason), the system can no
longer function.
Arguments:
Arg1: 0000000000000003, Process
Arg2: fffffa8008159060, Terminating object
Arg3: fffffa8008159340, Process image file name
Arg4: fffff80002f935d0, Explanatory message (ascii)
Debugging Details:
PROCESS_OBJECT: fffffa8008159060
IMAGE_NAME: csrss.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 0
MODULE_NAME: csrss
FAULTING_MODULE: 0000000000000000
PROCESS_NAME: csrss.exe
EXCEPTION_RECORD: fffff8800a977b78 -- (.exr 0xfffff8800a977b78)
ExceptionAddress: 0000000077a8592d
   ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 0000000000000001
   Parameter[1]: 0000000002ea0ef8
Attempt to write to address 0000000002ea0ef8
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
CURRENT_IRQL: 0
ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
EXCEPTION_PARAMETER1: 0000000000000001
EXCEPTION_PARAMETER2: 0000000002ea0ef8
WRITE_ADDRESS: 0000000002ea0ef8
FOLLOWUP_IP:
+0
00000000`77a8592d ??              ???
FAULTING_IP:
+0
00000000`77a8592d ??              ???
FAILED_INSTRUCTION_ADDRESS:
+0
00000000`77a8592d ??              ???
BUGCHECK_STR: 0xF4_C0000005
STACK_TEXT:
fffff880`0a9770f8 fffff800`03014652 : 00000000`000000f4 00000000`00000003 fffffa80`08159060 fffffa80`08159340 : nt!KeBugCheckEx
fffff880`0a977100 fffff800`02fbd3e3 : ffffffff`ffffffff fffffa80`0ab4f060 fffffa80`08159060 fffffa80`08159060 : nt!PspCatchCriticalBreak+0x92
fffff880`0a977140 fffff800`02f4580c : ffffffff`ffffffff 00000000`00000001 fffffa80`08159060 fffff6fb`00000008 : nt! ?? ::NNGAKEGL::`string'+0x17946
fffff880`0a977190 fffff800`02c87993 : fffffa80`08159060 fffff800`c0000005 ffffcbdb`afa4f658 fffffa80`0ab4f060 : nt!NtTerminateProcess+0x20c
fffff880`0a977210 fffff800`02c83f30 : fffff800`02cc2dbc fffff880`0a977b78 fffff880`0a9778e0 fffff880`0a977c20 : nt!KiSystemServiceCopyEnd+0x13
fffff880`0a9773a8 fffff800`02cc2dbc : fffff880`0a977b78 fffff880`0a9778e0 fffff880`0a977c20 00000000`02ea2180 : nt!KiServiceLinkage
fffff880`0a9773b0 fffff800`02c87d82 : fffff880`0a977b78 00000000`000116e4 fffff880`0a977c20 00000000`02ea1c58 : nt!KiDispatchException+0x53b
fffff880`0a977a40 fffff800`02c868fa : 00000000`00000001 00000000`000116e4 fffffa80`079c2201 00000000`77a85a01 : nt!KiExceptionDispatch+0xc2
fffff880`0a977c20 00000000`77a8592d : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x23a
00000000`02ea0f00 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x77a8592d
STACK_COMMAND: kb
FOLLOWUP_NAME: MachineOwner
FAILURE_BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
BUCKET_ID: X64_0xF4_C0000005_IMAGE_csrss.exe
Followup: MachineOwner

Screens Crashing/Blue Screening

I bought the Satellite C655-S5225 only a few days ago and I'm finding that whatever screens I have pulled up crash every 20minutes or so, it doesn't matter how many screens I have...whether it's 1-4, they always seem to crash or send me to the blue screen. It'll never fully exit from the screens even when I bring up the task manager, and I end up having to restart it often. I've googled the problem and it's something a few others have experienced, so I'm wondering if there's any solution for this, without me having to go back to best buy 20miles away?

Satellite C655-S5225
If you want to fool around with this, Jack, you can. But I would take the machine back to Best Buy and get one that works.
Otherwise, please attach the corresponding *.dmp files from the C:\Windows\Minidump folder. Maybe we can find something simple.
-Jerry

IMac LCD screen replaced, Blue Screen startup

Similar Messages

Maybe you are looking for