Imac motherboard failure after replacing optical drive

I replaced my super drive and made sure to replace thermal paste with new. -It initially booted OK, and I started to run software update.
--In the midst of that it crashed, but I was able to re-start it and finally complete the on-line update.
--But the machine kept crashing, and ultimately had what is called a "kernel panic" error.
--But then it would not even re-boot.
--I loaded the hardware diagnostic disk into the machine, but by then even it would not run.

Hi R,
I would definitely go back to the Apple Store and work with them as this is a warranty issue.

Similar Messages

Late 2005 2.3. Replacement optical drive?

My G5 is coming up on 3 years old and I have started to look at new hard drives and optical drives just in case either of mine start going bad.
Anyway, I was at the Apple store today, and one of the genies told me my only option for a replacement optical drive was an external through Apple?
From searching online, all the direct replacement internal optical drives are no longer manufactured. What are you guys replacing your optical drives with as far as internal ones?
The genie told me the drive has to be matched with the motherboard?
Thanks for any advice.

Hi-
What a bunch if mis-information.....
Popular drives such as these drives will work fine in the G5. The DVR-115 from Pioneer is readily supported in OS X, and the soon to appear on the North American market, Pioneer DVR-116 would also be a good choice.
Further confirmation of what others are using can be found by using the Xlr8yourMac Drive Data base. Enter "optical drive" and "G5" in the fields and search.
Same with hard drives, Hitachi and Western Digital provide excellent drives, with excellent compatibility in the G5.

MacBook Pro does not boot past apple screen after replacing hard drive

After replacing hard drive on MacBook Pro 13 inch early 2011 model, the screen only boots to the apple logo. Do I need to re-install the OS?

The problem is that the OS is not in any where else of the MacBook Pro than in the HD / SSD. If you replace the Hard Drive, then you will need to Re-install OSX into that hard drive, it's pretty easy.
1) Power up your Macbook Pro, as fast as you can press and hold the Option key (ALT). You'll see that it opens the bootable-devices you have, you'll see a Recovery partition, click it.
(If the Hard Drive contains data do the following)
2) In the menu select Disk Utility.
3) In Disk Utility go ahead and select the Hard Drive that is inside the MBP.
4) Erase the content.
(If the Hard Drive contains no data continue with the following jumping the last 3 steps).
5) Select Re-install OSX.
6) Select the Hard Drive in which you want to install it.
Follow the steps of everything else (it should take approximately 1 hour to do the whole thing).
Hope this helps!
Later.

Replacing optical drive ?

is there any problems replacing optical drive [Superdrive] with a secondry HDD using a caddy

It will void your warranty. Otherwise it can be a plus.
OWC http://eshop.macsales.com/shop/drive_bracket/datadoubler/

Replaced optical drive now locked out of hard drive hdd start up drive will mount

replaced optical drive now locked out of hd start up drive will not mount can some one help me

I didn't ask you if you thought you ordered the correct optical drive...
You opened up the machine. You made a change. Now it doesn't work. Reverse what you did and see if it works again. I'm assuming that the machine actually worked before you did this, right?

How do I reinstall CS6 Extended 64-bit after replacing hard drive and OS?

How do I reinstall CS6 Extended 64-bit after replacing hard drive and Windows 7 64-bit OS?

You can download the trial installer directly. Find the appropriate link below.
You must be on a trial download page to use the links, otherwise you get an error message.
For example, load the following page: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us
before pasting the link into the address bar.
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.7z
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.exe
You need to kepp both files downloaded into same folder and after download click on .exe file to extract .7z

Replacement optical drive for '07 20" iMac.

Have a 2007 20" iMac, that was refurbed in 2008, who's optical drive(DVR-K06PD) was making horrible noises. As there seems to be a rather high failure rate with these, thought I'd replace it with something else.
Picked up a Sony AD-7630A after reading that people had success with it. Worked OK...except it wouldn't eject media consistently. Then tried a UJ85C that was available. It worked fine until you put the bezel back on the computer. Then it wouldn't load media unless you pushed it in with something. Even a swift shove wouldn't get it completely past the slot protector.
After a bit of poking around, it seems that only the K06 will work in these iMacs. I did find a repair site that mentioned a UJ-875, but that was the only other one. Hoping someone might know of good replacements. There is not a lot of info out there. Puzzling, as they've been around for a couple of years. Lots of references to the white versions.
Thanks
PS - In researching this, I did come across a blurb from the Apple KB that recommended that these drives only be used in a horizontal position!.

The www.ifixit.com website says that your iMac needs this replacement drive; 12.7 mm PATA 8x Pioneer SuperDrive They list this part number, but I cannot tell if that is Pioneer's number or their in-house number; IF167-005-1. They say that your iMac has different mounting slots and requires this drive to correctly attach to the optical drive bracket.
Dah•veed

After Replacing Hard Drive, iMac Freezes after about 40 Minutes.

I have a flat panel 15" iMac which had a bad hard drive. I replaced it with a 250 gig Seagate ATA drive. I used the Disck utility to format it and the computer recognized the correct size of the Drive. After installing OS 10.4.7 on the drive I found that the computer locks-up or frezzes after about 45 minute. I have run apple diagnoxtics and the computer hardware and ram checks out fine. I found that the computer does not lock up if I runit form an external firewire drive with os 10.x and it did not lock-up when I booted form the OS 9 Hardware test cd. I then thought that maybe I had loaded the OS x poorly on th e new drive so I reloaded the OS. The system agin freezes agter the system is on for about 30 + minutes.
Do I need a special drive or size for the G4 flat panel iMac? Is there a setting on the Segate Drive I need to set.
Any Thoughts\
Jim
G4 Dual 1.25 Mac OS X (10.2.x)

Hello,
There should be a Master / Slave setting on the drive. If it shares the same "channel" with your CD-ROM drive, then you may need to set the Hard Drive as Master.
Check your original drive, and see what it was set to. There is a Master, Slave, and Factory setting.
Look at the label on the drive, and compare that to the jumpers (little caps) on the back of the drive by the data cable connector.
Set your new drive to match the same setting your original drive was set to.
If that doesn't work, try your new drive in the external drive enclosure. See if it works right there.
If it still doesn't work right, then perhaps you got a drive with a defect.
If it works fine in the external case, and you have verified that your settings are right when used internally, then you may have damage in the iMac's logic board or hard drive controller somewhere.
But, take a look at the Jumper Settings, and try it in the external enclosure as well. See if either of those fixes it.
Hopefully you just got the jumper settings wrong.
I hope this helps.

Replacement Optical Drive Issues

A friend of mine had a label detach and disintegrate inside her DVD drive. I took it apart and cleaned all the bits and pieces out as best I could. When I put everything back together System Profiler couldn't detect a burning device. The drive seemed to be semi-functional because it sucked in a disk and made noises. Unfortunately, I could not eject the disk and found that I had to disassemble the iMac and drive again to get the disk out. I thought that perhaps the exploding label had somehow damaged the drive to the point the iMac couldn't recognize it so I found what I thought was a replacement on eBay. The iMac had a DVR-K05PA model installed but the eBay unit that showed up was a DVR-K05 (no PA suffix). I installed it anyway but I get the same result: System Profiler says no burning device was detected. The drive was advertised as fully functional but is it the wrong model number? Is the motherboard on this machine faulty or where else could the problem be? The machine works fine except for no DVD drive.

Hi Larry
What iMac, what OS X is it on, what Optical Drive came out, what Firmware Revision is listed in the System Profiler, is it the 17" Early 2006 4,1 listed in your Profile or some other iMac year/model....????
Start off reseting the SMC > http://support.apple.com/kb/HT3964
+1. Shut down the computer.+
+2. Unplug the computer's power cord.+
+3. Press and hold the power button for 5 seconds.+
+4. Release the power button.+
+5. Attach the computers power cable.+
+6. Press the power button to turn on the computer.+
and restart resetting the PRAM > http://support.apple.com/kb/HT1379
+1. Shut down the computer.+
+2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.+
+3. Turn on the computer.+
+4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.+
+5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.+
+6. Release the keys.+
Dennis
Message was edited by: den.thed
Woops' that's why they call me "day late and dollar short" I never say your second post.....

Pismo does not boot after replacing hard drive

We have had an old Pismo for several years now. Two or so years ago we decided to replace the stock 6GB hard drive, which was getting full, with a new 60GB drive. We cloned the old drive via target disk mode, popped in the new drive, copied the data back (again via target disk mode), and were surprised when we were met with the flashing question mark/system folder icon. Sort of left it at that and forgot about it.
I stumbled upon the Pismo again today and decided to see if I couldn't get it working. After going through a few "why won't this even turn on" sessions (the machine hadn't been powered on in a few years, so pulling the internal battery and resetting the PMU fixed that), I popped the old drive back in and the machine booted just fine. Cloned the original drive (again) using Carbon Copy Cloner via target disk mode to a disk image on my MacBook. Powered it down, put the new (60GB) drive back in the Pismo, cloned the disk image back to the new drive. The data's there, because I can browse it in target disk mode, but I can't boot off the new hard drive. I can't boot off my Tiger install DVD either - the DVD drive spins up and tries to access the disc, but won't boot. I'm going to try and get my hands on the CD version of Tiger to see if there's a difference using that.
Disk Utility on the MacBook says there's nothing wrong with the Pismo's hard drive, but I'm not convinced that's the case. I'd heard about Pismos being picky with certain types of hard drives, is this true? If not, what other issues might be leading to this behavior?

Is this perhaps an artifact of the drive being formatted via target disk mode on my MacBook
I suspect that the problem lies somewhere in that situation. I suggest that you boot from the install disk as I suggested previously and reformat the HDD and reinstall the OS.
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• Boot the MacBook Firewire Target Disk Mode.
• Insert install disk into MacBook's optical drive.
• Connect computers via firewire cable
• Option Boot Pismo.
• Select Install Disk for startup and click on the straight arrow.
• Select language
• Go to the Utilities menu (Tiger and later) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• Click on Options button
• Select Apple Partition Map (PPC Macs)
• Click OK
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Apply/Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
Open installer and begin installation process.
cornelius

Create a restore point fails with 0x81000101 error after replacing hard drives

I recent had a hard drive failure so, figuring that I may as well gain something for all of the work, I replaced both drives in my RAID 1 array (thereby doubling the drive space). I then restored from back up and all has appeared well for several months
now. Last week I started having trouble with RDC which led me to potential issues with my Intel RAID driver which finally led me to System Restore points. It turns out that they haven't been working for some time now and I've been unable to get
them started using any of the advice in the other discussions on this particular topic.
All of the necessary services should be running. I've also tried turning system protection off/on.
The new information that I provide is that when I first opened the System Protection tab, I found two entries for the C: drive. The first had protection turned off. The second, named OS, was listed as missing. After a couple of attempts
with the configuration, I ended up with one entry for OS (C:) with protection On. It still didn't work which led me to the forum and many failed attempts at getting this one feature working.
One of the other discussions mentioned the RestoreSystem log files. They are, of course, binary files but I was able to see that I'm getting something called SxRegReadDWORD4FAILED6 fairly soon followed later by a FAILED CSpp::_CreateSnapshotSet.
I'm hoping that somebody with the right tool and knowledge to actually read those files can help me get restore points working again.

Hi,
What is the full error messages? Like this?
The shared restore point operation failed with error (0x81000101) The creation of a shadow copy has timed out. Try this operation again.
If yes, then we might take a try with the method mentioned in the below blog:
Windows Server Backup failed to backup with error 0x81000101
Let us know the process.
Best regards
Michael Shao
TechNet Community Support

Aluminum imac isn't reconizing the optical drive

hello all. i visited an old digital graphics teacher today, and it turns out he's having a problem with one of his imacs in his classroom. it acts as though it doesn't have an optical drive, and he's got a rather expensive 3d program trapped inside of it. he has no idea how to get it out or what's wrong with the drive. it doesn't recognize the disk and refuses to eject it. i told him i would do my best to find out what was wrong and i found a few tips on how to force eject a disk, though i haven't been back to give those tips a try. just wondering if anyone else has had this problem with the brand new imacs (he says they are about 11 months old) and if it is something software related that will eventually get fixed, or if this particular optical drive is busted and needs to be replaced. thanks in advance. i'll update on our progress.

I am having the exact same problem. Have an audio cd stuck in the drive and wont eject. Computer doesn't recognize that there is a disk in the machine and it doesn't even recognize that it has a superdrive. Upon restart it spins loudly and then stops. Optics drive has been giving me problems off and on since I got it with not ejecting but always seemed to get it out when restarted machine, not so this time. Should of had it looked at sooner and now it is 15 months old. Any suggestions before I dump out $ for apple help?

2nd HDD caddy replacing optical drive for HP Pavilion 15-e073ca Notebook PC & Windows 10

Hello ! I am planning to add a SSD to my two-years-old HP Pavilion 15-e073ca Notebook PC. I found on some sites that I can remove the optical drive and put a second drive using a caddy adapter into the optical drive bay. I found that some people on the forum have done it successfully, but nothing about my PC model. I want to know if it could work with my product. In other words, there is my plan:1-Remove the actual HDD from the hard drive bay and replace it with the new SSD.2-Remove the optical drive and replace it with the caddy adapter containing my old HDD.3-Do a clean install of Windows 10 on the SSD, using a USB recovery flash drive made with my actual Windows 10 system (which was updated from Windows 8.1). I am planning to buy the following parts:1- a HDD / SSD caddy adapter for HP Pavilion 15 (model OBHD9-SATA-SATA-BU9), from NewmodeUS (http://www.newmodeus.com/shop/index.php?main_page=product_info&cPath=2_5&products_id=583)2- a 128 GB SSD drive (item SDSSDHP-128G), from SanDisk (http://www.sandisk.com/products/ssd/sata/ultra-plus/?capacity=128gb) I have some questions before buying the parts:1- Will the two drives (my old HDD and the new SSD) be recognized by the motherboard / BIOS and the operating system (Windows 10)? Is there a limit of one unique HDD/SSD drive on the computer?2- The height of the SSD is 7mm, and it seems that my old HDD is 9.5mm height (model WDC WD10JPVT-60A1YT0). Would it cause any problem (would I need to add spacers)?3- Do these parts work together and with my computer (size, compatibility)? Do you expect any problem with this upgrade?4- Will the clean install of Windows 10 work, since I plan to install it on a different drive than the one I used to create the USB recovery flash drive? I have never done a clean Windows installation before. Thanks in advance for your replies.Haghe

Hi:
Use the W7 32 bit drivers and software from the Probook 450 G2 except the graphics, firmware and BIOS files.
http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=6943827&swLangOid=8&swEnvOid=4053
Graphics:
First install the Intel chipset installation utility from the above model and reboot.
Second, install the Intel HD graphics driver and reboot.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=24246
Then install the nVidia graphics driver and reboot.
http://www.nvidia.com/download/driverResults.aspx/79892/en-us

I replaced optical drive, now MacBookPro is very hot and wifi hardware not installed

My late 2008 MacBookPro 5,1 2.53 GHz laptop's optical drive would not record last week. A lens cleaning didn't help, so I replaced the optical drive Tuesday evening with iFixit instructions. Other than stripping one of the screws holding the drive in place, all seemed pretty straightforward. I had to disconnect the camera cable to get the drive out but replaced it. After putting everything back together, the new drive seemed to burn discs well and everything (including the camera) worked perfectly.
Last night I came home to the laptop, which, as usual, was sleeping and connected to the AC adapter. Not as usual, it was really hot. I restarted it and when it rebooted the wifi icon had an x in it and said wifi:hardware not installed.
I reset the PRAM and the SMC. No luck.
I have an appointment to take it to a genius bar tomorrow afternoon, but what could I have done without realizing it?
Thanks for any suggestions (I have been working on Mac desktops and laptops for a number of years...this is the first time anything like this has happened to me...)

That is true. I cannot think of any way to test the Optical Drive without swapping it into a known correctly operating MBP.
A thought which probably may not be an issue. When I installed an Optical Drive in my old (2006) MBP, I remember seeing in the instruction manual an item called a grounding pad (which looked like a tiny steel brillo pad with out soap) which was missing in mine. The MBP worked and I essentially ignored it. Perhaps that may not be case with your situation.
My thoughts are that the Optical Drive is malfunctioning and the cause of your problem. Perhaps you should consider getting a new replacement from OWC. But that entails a $100 risk with no guarantees of success.
Ciao.

Replacing optical drive with SSD and HD with new HD

Hi folks, recently my macbook pro unibody's (2011) hard drive started encountering some fatal errors. I've gone through all possible fixes, and it looks like the only option left is to replace the HDD. As much as this initially bummed me out, I'm a little excited about the prospect now. I think I would like to go ahead and replace the optical drive with a SSD while I have the computer open to replace the HDD. This will breathe some serious new life into my macbook pro.
My question is, which SSD's and HDD's are compatible with the macbook and which brands do you guys (the community) recommend? Should I upgrade my ram while I'm in there? How difficult of a job is this? I am mechanically inclined but I have much more experience working on tractors than electronics. Thanks for any advice or input you can offer!

Go to OWC to get the Data Doubler bracket for your model. You can also find HDDs and SSDs there. Be sure to put the SSD where the HDD is located and put the HDD in the optical drive bay. Upgrading RAM is always a good idea. I've done all these in my 2011 MBP. OWC also provides tools needed and online video tutorials.
For optimum use of this combo only install OS X on the SSD. Install everything else on the HDD. Then follow these instructions for setting it up to have the computer boot from the SSD but use your Home folder that is on the HDD:
How to use an SSD with your HDD
If you are going to use an SSD as a boot drive together with your existing HDD as the "data" drive, here's what you can do.
After installing the SSD you will need to partition and format the SSD using Disk Utility. Then, install OS X on the SSD. After OS X has been installed boot from the SSD. Use Startup Disk preferences to set the SSD as the startup volume.
Open Users & Groups preferences. Click on the lock icon and authenticate. CTRL- or RIGHT-click on your user account listing in the sidebar and select Advanced Options from the context menu. You will see a field labeled "Home dir:" At the right end you will see a Change button. Click on it. In the file dialog locate the Home folder now located on the HDD (HDD/Users/account_name/.) Select the folder, click on Open button. Restart the computer as directed.
When the computer boots up it will now be using the Home folder located on the HDD.
Another more technical method involving the Terminal and aliases is discussed in depth here: Using OS X with an SSD plus HDD setup - Matt Gemmell. This is my preferred approach because I can select which of the Home's folders I want on the HDD and which I don't want. For example, I like to keep the Documents and Library folders on the SSD because I access their content frequently.
Be sure you retain the fully bootable system on your HDD in case you ever need it.
Be sure to use Trim Enabler 3.3 to activate TRIM on the SSD.

Imac motherboard failure after replacing optical drive

Similar Messages

Maybe you are looking for