IMac Restart error issue

Hey There...
I've been getting an error message on the screen just out of the blue, that is in several different languages and says I need to restart... It happens periodically sometimes when it sits in idol or when your working on it, sometimes when you power it on, nothing concert...
I've done the following...
1. re-imaged HD
2. repaired permissions (over and over again)
3. replaced the HD
4. replaced the RAM
5. replaced the logic board and power supply...
But it's still happening... Any other suggestions other then it accidently falling off the side of the desk...

Usually such an error message implies a kernel panic; but they can occur without
the message being seen in some cases.
There are some instructions on how to progressively attempt to root out kernel panics
here: "Resolving Kernel Panics" http://www.thexlab.com/faqs/kernelpanics.html
There also may be some helpful ideas here:
"Technical Note TN2063: Understanding/Debugging Kernel Panics"
http://developer.apple.com/technotes/tn2002/tn2063.html
Hard to tell what else is going on, between the software and hardware in this regard.
Good luck and happy computing!

Similar Messages

My iMac restarts everytime time machine is backing getting this error

my iMac restarts everytime time machine is backing up i had time capsule so   i changed back up disk to seagate and still does it.
getting this error any help would be great and im not real computer smart
Interval Since Last Panic Report: 415540 sec
Panics Since Last Report:          5
Anonymous UUID:                    50E71E33-0C3E-B6B0-1F87-93F5501AF275
Fri Apr 12 18:09:41 2013
panic(cpu 0 caller 0xffffff8000e43d5b): "a freed zone element has been modified in zone: cluster_write"@/SourceCache/xnu/xnu-2050.18.24/osfmk/kern/zalloc.c:214
Backtrace (CPU 0), Frame : Return Address
0xffffff80f1b23680 : 0xffffff8000e1d626
0xffffff80f1b236f0 : 0xffffff8000e43d5b
0xffffff80f1b23730 : 0xffffff8000e435d2
0xffffff80f1b23810 : 0xffffff8000ee80cf
0xffffff80f1b23840 : 0xffffff8000ee4cd7
0xffffff80f1b239d0 : 0xffffff8000ee337e
0xffffff80f1b23c30 : 0xffffff8000ee2ff5
0xffffff80f1b23c60 : 0xffffff80010fb26d
0xffffff80f1b23d70 : 0xffffff8000f11da2
0xffffff80f1b23dd0 : 0xffffff8000f08179
0xffffff80f1b23e40 : 0xffffff80011770e9
0xffffff80f1b23ef0 : 0xffffff80011772e4
0xffffff80f1b23f50 : 0xffffff80011e182a
0xffffff80f1b23fb0 : 0xffffff8000eced33
BSD process name corresponding to current thread: backupd
Mac OS version:
12C60
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
Kernel slide:     0x0000000000c00000
Kernel text base: 0xffffff8000e00000
System model name: iMac11,1 (Mac-F2268DAE)
System uptime in nanoseconds: 4702215649822
last loaded kext at 237598977526: com.apple.filesystems.smbfs          1.8 (addr 0xffffff7f82f02000, size 229376)
last unloaded kext at 161063000383: com.apple.driver.AppleUSBUHCI          5.2.5 (addr 0xffffff7f81825000, size 65536)
loaded kexts:
com.seagate.driver.PowSecLeafDriver_10_5          5.2.4
com.seagate.driver.PowSecDriverCore          5.2.4
com.apple.filesystems.smbfs          1.8
com.apple.filesystems.msdosfs          1.8
com.apple.driver.AppleBluetoothMultitouch          75.15
com.apple.filesystems.ntfs          3.10
com.apple.driver.AudioAUUC          1.60
com.apple.driver.AGPM          100.12.69
com.apple.driver.AppleHWSensor          1.9.5d0
com.apple.driver.AppleMikeyHIDDriver          122
com.apple.filesystems.autofs          3.0
com.apple.driver.AppleHDA          2.3.1f2
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.kext.AMDFramebuffer          8.0.0
com.apple.iokit.IOBluetoothSerialManager          4.0.9f33
com.apple.driver.AppleMikeyDriver          2.3.1f2
com.apple.ATIRadeonX2000          8.0.0
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport          4.0.9f33
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.ApplePolicyControl          3.2.11
com.apple.driver.AppleBacklight          170.2.3
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.driver.AppleIRController          320.15
com.apple.driver.AppleUSBCardReader          3.1.0
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.2
com.apple.driver.AppleUSBHub          5.2.5
com.apple.driver.AppleFWOHCI          4.9.6
com.apple.iokit.AppleBCM5701Ethernet          3.2.5b3
com.apple.driver.AirPort.Atheros40          600.70.23
com.apple.driver.AppleAHCIPort          2.4.1
com.apple.driver.AppleUSBEHCI          5.4.0
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.driver.AppleBluetoothHIDKeyboard          165.5
com.apple.driver.AppleHIDKeyboard          165.5
com.apple.driver.IOBluetoothHIDDriver          4.0.9f33
com.apple.driver.AppleMultitouchDriver          235.28
com.apple.kext.triggers          1.0
com.apple.driver.DspFuncLib          2.3.1f2
com.apple.iokit.IOAudioFamily          1.8.9fc10
com.apple.kext.OSvKernDSPLib          1.6
com.apple.iokit.IOSurface          86.0.3
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.iokit.IOBluetoothFamily          4.0.9f33
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport          4.0.9f33
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.AppleHDAController          2.3.1f2
com.apple.iokit.IOHDAFamily          2.3.1f2
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.driver.AppleSMC          3.1.4d2
com.apple.kext.AMD4800Controller          8.0.0
com.apple.kext.AMDSupport          8.0.0
com.apple.driver.AppleGraphicsControl          3.2.11
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.iokit.IONDRVSupport          2.3.5
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.iokit.IOGraphicsFamily          2.3.5
com.apple.iokit.IOUSBHIDDriver          5.2.5
com.apple.iokit.IOUSBMassStorageClass          3.5.0
com.apple.driver.AppleUSBMergeNub          5.2.5
com.apple.driver.AppleUSBComposite          5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOFireWireSBP2          4.2.0
com.apple.iokit.IOSCSIBlockCommandsDevice          3.5.1
com.apple.iokit.IOAHCISerialATAPI          2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          5.2.5
com.apple.iokit.IOEthernetAVBController          1.0.2b1
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOAHCIFamily          2.2.1
com.apple.iokit.IOUSBFamily          5.4.0
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.21
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7.2
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
Model: iMac11,1, BootROM IM111.0034.B02, 4 processors, Intel Core i7, 2.8 GHz, 8 GB, SMC 1.54f36
Graphics: ATI Radeon HD 4850, ATI Radeon HD 4850, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533642465238432D47372020
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533642465238432D47372020
Memory Module: BANK 0/DIMM1, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533642465238432D47372020
Memory Module: BANK 1/DIMM1, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533642465238432D47372020
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x8F), Atheros 9280: 4.0.70.23-P2P
Bluetooth: Version 4.0.9f33 10885, 2 service, 18 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Network Service: Leapfrog Device (en5), Ethernet, en5
Serial ATA Device: ST31000528AS, 1 TB
Serial ATA Device: HL-DT-ST DVDRW GA11N, 9.2 MB
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfa100000 / 2
USB Device: Backup+ Desk Mac, 0x0bc2 (Seagate LLC), 0xa0a5, 0xfa130000 / 6
USB Device: USB-SATA Bridge, 0x067b (Prolific Technology, Inc.), 0x2571, 0xfa140000 / 5
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfa120000 / 4
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 3
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0xfa111000 / 7
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfd100000 / 2
USB Device: hub_device, 0x0409 (NEC Corporation), 0x005a, 0xfd130000 / 5
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd110000 / 4
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Restarting Error Workflows in Production Environment

Hi Experts,
I m having an issue in the prod enviroment there are some error workflows because of the error issued by the function in a method which i used in a workflow step.Know i have trapped that error .And i tried to restart the workflows by using SWPR.
Still the workflow is going to error status.
Please advice.
Thanks,
Rajesh.

Hello,
Is it showing the same error? Try SWU_OBUF.
regards
Rick Bakker
Hanabi Technology

"Error issuing replication: 8453 (0x2105)" when doing a repadmin /syncall

Whenever I do a repadmin /syncall I get "CALLBACK MESSAGE: Error issuing replication: 8453 (0x2105):"
If I do a repadmin /syncall /P the command completes with no errors
I am running this command from the only FSMO roles holder for my domain
This is also in our hub office which all of our branch offices connect to.
I was going to run "repadmin /syncall /e /P" to immediately replicate changes to all of our DCs, but I want to be sure this won't break anything.
I found two warnings in the following Microsoft article that worry me:
http://technet.microsoft.com/en-us/library/cc811569(v=ws.10).aspx
"These are very powerful subcommands and should be used sparingly as they do not follow replication agreements that are in place and have the potential to cause replication storm and break Active Directory if not used properly."
for the /syncall switch:
"Use this command and the above flags cautiously or you can damage the replication system because this command does not follow replication agreements nor honor any replication restrictions such as DISABLE_INBOUND_REPL or DISABLE_OUTBOUND_REPL"
Is running this command safe or will I cause problems by doing this? I was thinking that because this is the FSMO roles holder doing a /P (push) to the other DCs from this one would be ok.
I should also add that doing a "repadmin /replicate" to any DC executes without any errors.

Can you post the dcdiag /q,repadmin /replsum and repadmin /syncall details of DC's to analyse the same.Please use skydive to post the log
"Error issuing replication: 8453 (0x2105):" This can either be a DNS misconfig,secure channel between DC broken,lingering object issue or network connectivity issue,necessary ports are not fully opened between locations,etc. Microsoft's PortQry tests specific
AD ports and the ephemeral ports, and the required responses from the services on the required AD ports it specifically scans for. Here's more info on the ports that AD requires to properly communicate:
Active Directory Firewall Ports -
http://msmvps.com/blogs/acefekay/archive/2011/11/01/active-directory-firewall-ports-let-s-try-to-make-this-simple.aspx
Also, disable local windows firewall service, by default it is enabled in vista/windows 2008 and above. Check the network connectivity and latency.
Disable Windows Firewall:
http://technet.microsoft.com/en-us/library/cc766337(WS.10).aspx
Also ensure the following DNS setting on DC:
1. Each DC / DNS server points to its private IP address as primary DNS server and other remote/local DNS servers as secondary in TCP/IP properties.
2. Each DC has just one IP address and single network adapter is enabled.
3. Contact your ISP and get valid DNS IPs from them and add it in to the forwarders, Do not set public DNS server in TCP/IP setting of DC.
4. Once you are done, run "ipconfig /flushdns & ipconfig /registerdns", restart DNS and NETLOGON service each DC.
Do not put private DNS IP addresses in forwarder list.
5.Assign static IP address to DC if IP address is assigned by DHCP server to DC.It is strongly not recommended.
Hope this helps.
Best Regards,
Sandesh Dubey.
MCSE|MCSA:Messaging|MCTS|MCITP:Enterprise Adminitrator |
My Blog
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

My imac restarted but now it is taking forever

I upgraded from Mavericks to Yosemite and my imac restarted after installing. I entered my password and now there is a progress bar that has moved halfway after over an hour. I tried restarting the computer but that did not help. Is it normal to take this long? My new laptop had no problems.
I cannot give any specs because I cannot bring that info up on the computer.
Thanks for any help.
Catherine

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

IMac Restarts Often

My iMac restarts a couple time a night. Any ideas what might be causing it? Thanks!
Hardware Overview:
Model Name: iMac
Model Identifier: iMac12,2
Processor Name: Intel Core i7
Processor Speed: 3.4 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 16 GB
Boot ROM Version: IM121.0047.B1F
SMC Version (system): 1.72f2
Serial Number (system): D2*******HJW
Hardware UUID: *****
Anonymous UUID: 5AB2719C-2B59-4E49-AAFC-C01702F1D5A0
Mon Jun 30 19:59:07 2014
panic(cpu 4 caller 0xffffff802b4dbf5e): Kernel trap at 0xffffff802b4725c3, type 13=general protection, registers:
CR0: 0x000000008001003b, CR2: 0x00007f9c2d07b008, CR3: 0x000000002e2e4000, CR4: 0x00000000000606e0
RAX: 0x0000000000000000, RBX: 0x0000000000000000, RCX: 0xffffff81ecb83b30, RDX: 0x0000000000000000
RSP: 0xffffff81ecb83a20, RBP: 0xffffff81ecb83e20, RSI: 0xffffff803fcb24a0, RDI: 0xfffffffff0000000
R8: 0x0000000000800000, R9: 0x0000000000000fff, R10: 0xffffff81ecb83b30, R11: 0x003dec0200100000
R12: 0x0000000000000000, R13: 0xffffff806bc3b8c0, R14: 0x003dec0200100000, R15: 0x0000000000000000
RFL: 0x0000000000010286, RIP: 0xffffff802b4725c3, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x00007f9c2d07b008, Error code: 0x0000000000000000, Fault CPU: 0x4
Backtrace (CPU 4), Frame : Return Address
0xffffff820cbaddf0 : 0xffffff802b422fa9
0xffffff820cbade70 : 0xffffff802b4dbf5e
0xffffff820cbae040 : 0xffffff802b4f3456
0xffffff820cbae060 : 0xffffff802b4725c3
0xffffff81ecb83e20 : 0xffffff802b471fcd
0xffffff81ecb83e80 : 0xffffff802b801e61
0xffffff81ecb83eb0 : 0xffffff802b5dc02d
0xffffff81ecb83f00 : 0xffffff802b5db710
0xffffff81ecb83f40 : 0xffffff802b5e27d0
0xffffff81ecb83f70 : 0xffffff802b5d8888
0xffffff81ecb83fb0 : 0xffffff802b4d7127
BSD process name corresponding to current thread: kernel_task
Mac OS version:
13D65
Kernel version:
Darwin Kernel Version 13.2.0: Thu Apr 17 23:03:13 PDT 2014; root:xnu-2422.100.13~1/RELEASE_X86_64
Kernel UUID: ADD73AE6-88B0-32FB-A8BB-4F7C8BE4092E
Kernel slide: 0x000000002b200000
Kernel text base: 0xffffff802b400000
System model name: iMac12,2 (Mac-942B59F58194171B)
System uptime in nanoseconds: 91496046211377
last loaded kext at 89645370706600: com.apple.driver.AppleIntelMCEReporter 104 (addr 0xffffff7fadcce000, size 49152)
last unloaded kext at 89763303087123: com.apple.driver.AppleIntelMCEReporter 104 (addr 0xffffff7fadcce000, size 32768)
loaded kexts:
com.seagate.driver.PowSecLeafDriver_10_5 5.2.6
com.seagate.driver.PowSecDriverCore 5.2.6
com.apple.filesystems.afpfs 11.1
com.apple.nke.asp-tcp 8.0.1
com.apple.filesystems.smbfs 2.0.2
com.apple.driver.AppleBluetoothMultitouch 80.14
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AGPM 100.14.15
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOBluetoothSerialManager 4.2.4f1
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleMikeyDriver 2.6.1f2
com.apple.driver.AppleHDA 2.6.1f2
com.apple.driver.AppleUpstreamUserClient 3.5.13
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.kext.AMDFramebuffer 1.2.2
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.4f1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.AMDRadeonX3000 1.2.2
com.apple.driver.AppleBacklight 170.3.5
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleMCCSControl 1.1.12
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.driver.AppleLPC 1.7.0
com.apple.kext.AMD6000Controller 1.2.2
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleThunderboltIP 1.1.2
com.apple.driver.AppleIntelHD3000Graphics 8.2.4
com.apple.driver.AppleIntelSNBGraphicsFB 8.2.4
com.apple.driver.AppleIRController 325.7
com.apple.iokit.SCSITaskUserClient 3.6.6
com.apple.driver.AppleUSBCardReader 3.4.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.5.1
com.apple.driver.AppleUSBHub 666.4.0
com.apple.iokit.AppleBCM5701Ethernet 3.8.1b2
com.apple.driver.AirPort.Atheros40 700.74.5
com.apple.driver.AppleFWOHCI 5.0.2
com.apple.driver.AppleAHCIPort 3.0.0
com.apple.driver.AppleUSBEHCI 660.4.0
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleACPIButtons 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.1
com.apple.driver.AppleACPIEC 2.0
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 217.92.1
com.apple.nke.applicationfirewall 153
com.apple.security.quarantine 3
com.apple.driver.AppleIntelCPUPowerManagement 217.92.1
com.apple.security.SecureRemotePassword 1.0
com.apple.driver.AppleMultitouchDriver 245.13
com.apple.driver.AppleBluetoothHIDKeyboard 170.15
com.apple.driver.IOBluetoothHIDDriver 4.2.4f1
com.apple.driver.AppleHIDKeyboard 170.15
com.apple.kext.triggers 1.0
com.apple.iokit.IOSerialFamily 10.0.7
com.apple.driver.DspFuncLib 2.6.1f2
com.apple.vecLib.kext 1.0.0
com.apple.iokit.IOAudioFamily 1.9.7fc2
com.apple.kext.OSvKernDSPLib 1.14
com.apple.iokit.IOSurface 91.1
com.apple.iokit.IOBluetoothFamily 4.2.4f1
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.4f1
com.apple.iokit.IOAcceleratorFamily 98.20
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusPCI 1.0.12d1
com.apple.driver.AppleSMBusController 1.0.11d1
com.apple.driver.AppleHDAController 2.6.1f2
com.apple.iokit.IOHDAFamily 2.6.1f2
com.apple.kext.AMDSupport 1.2.2
com.apple.AppleGraphicsDeviceControl 3.5.26
com.apple.iokit.IOFireWireIP 2.2.6
com.apple.driver.AppleSMC 3.1.8
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.7.0d11
com.apple.driver.AppleThunderboltEDMSink 2.1.3
com.apple.iokit.IONDRVSupport 2.4.1
com.apple.iokit.IOGraphicsFamily 2.4.1
com.apple.iokit.IOAHCISerialATAPI 2.6.1
com.apple.driver.AppleThunderboltDPOutAdapter 3.1.7
com.apple.driver.AppleThunderboltDPInAdapter 3.1.7
com.apple.driver.AppleThunderboltDPAdapterFamily 3.1.7
com.apple.driver.AppleThunderboltPCIDownAdapter 1.4.5
com.apple.iokit.IOUSBHIDDriver 660.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.6
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOUSBMassStorageClass 3.6.0
com.apple.iokit.IOFireWireSerialBusProtocolTransport 2.5.1
com.apple.driver.AppleUSBMergeNub 650.4.0
com.apple.driver.AppleUSBComposite 656.4.1
com.apple.iokit.IOFireWireSBP2 4.2.6
com.apple.iokit.IOSCSIBlockCommandsDevice 3.6.6
com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.6
com.apple.driver.AppleThunderboltNHI 2.0.1
com.apple.iokit.IOThunderboltFamily 3.2.7
com.apple.iokit.IOUSBUserClient 660.4.2
com.apple.iokit.IOEthernetAVBController 1.0.3b4
com.apple.driver.mDNSOffloadUserClient 1.0.1b5
com.apple.iokit.IO80211Family 630.35
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOAHCIFamily 2.6.5
com.apple.iokit.IOUSBFamily 677.4.0
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 278.11
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.AppleKeyStore 2
com.apple.driver.DiskImages 371.1
com.apple.iokit.IOStorageFamily 1.9
com.apple.iokit.IOReportFamily 23
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 2.0
com.apple.iokit.IOPCIFamily 2.9
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.pthread 1
com.apple.kec.corecrypto 1.0
Unable to gather system configuration information.Model: iMac12,2, BootROM IM121.0047.B1F, 4 processors, Intel Core i7, 3.4 GHz, 16 GB, SMC 1.72f2
Graphics: AMD Radeon HD 6970M, AMD Radeon HD 6970M, PCIe, 2048 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1333 MHz, 0x830B, 0x4E54344743363442384847304E532D434720
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1333 MHz, 0x830B, 0x4E54344743363442384847304E532D434720
Memory Module: BANK 0/DIMM1, 4 GB, DDR3, 1333 MHz, 0x830B, 0x4E54344743363442384847304E532D434720
Memory Module: BANK 1/DIMM1, 4 GB, DDR3, 1333 MHz, 0x830B, 0x4E54344743363442384847304E532D434720
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x9A), Atheros 9380: 4.0.74.0-P2P
Bluetooth: Version 4.2.4f1 13674, 3 services, 23 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Serial ATA Device: WDC WD1001FALS-403AA0, 1 TB
Serial ATA Device: OPTIARC DVD RW AD-5680H
USB Device: Hub
USB Device: My Book 1234
USB Device: Back-UPS NS 600 FW:818.w1 .D USB FW:w1
USB Device: BRCM2046 Hub
USB Device: Bluetooth USB Host Controller
USB Device: FaceTime HD Camera (Built-in)
USB Device: Hub
USB Device: FreeAgent Go
USB Device: Hub
USB Device: iPhone
USB Device: FreeAgent
USB Device: FreeAgent
USB Device: iPhone
USB Device: FreeAgent
USB Device: FreeAgent
USB Device: Internal Memory Card Reader
USB Device: IR Receiver
FireWire Device: My Book 1112, WD, Up to 800 Mb/sec
Thunderbolt Bus: iMac, Apple Inc., 22.1
<Personal Information Edited by Host>

None of the RAM you have is from the factory. If you didn't install it, the retailer did.
Remove two of the modules and test. Then swap modules and test again.

SAP PI Message Cancellation Alert - Message does not have restartable error status

Hello SCNers
Version: 7.1
Scenario: File --> PI -->SOAP
We have a situation where a PI message in Integration Engine shows error status.We want to cancel the message in IE but are unable to do so.
On clicking Cancel for this message in SXMB_MONI, we are receiving an alert "Message does not have restartable error status".
In SXMSPMAST table, value for ITFACTION is DEL.
We do not want to run report RSXMB_DEL_TO_ARCH, that would change status of all messages with DEL status to ARCH.
Is there a way to Cancel or Change the Status of this single message?
Regards
Sudheer

Hi Hareesh,
Tried that too, but to no avail.
Strangely, the log shows NO_ERROR_STATE for the cancelation of this message thru RSXMB_CANCEL_MESSAGES.
But in SXMSPMAST table the status of this message is 14 (System Error - Manual Restart Possible).
Regards
Sudheer

"Bridge is running low on memory and should be restarted" error

I am running Bridge CS4 on a DELL T-1650 with plenty of hard drive space. I am having trouble with indexing / caching files. My computer is connected to a large office server with a large amount of files that I need to be able to search. I recieve a "Bridge is running low on memory and should be restarted" error each time I attempt to index the files on the server drive. I have tried Purge and Cache, set the cache memory slider to max. This is a very large amount of files (TB ) to index /cache. I leave the computer running overnight to allow ample time, I nothing on my TB hard drive , and have 16GB of available RAM. Any ideas?

…My computer is connected to a large office server…
Aha! Working over a network is not supported by Adobe.
This is the boilerplate text often used in connection to saving to a network (please NOTE the part where it explains that normally, it does work, but that it is impossible to troubleshoot someone else's network remotely, and that's why it's not supported by Adobe):
If you are opening files over a network or saving them to a network server, please cease and desist immediately in the event you are currently experiencing problems with one or more files. Working across a network is not supported.
See:
http://kb2.adobe.com/cps/406/kb406793.html
Copy the CLOSED file from your server to your local hard disk, work on it, save it again to your local hard disk, close it, and copy the closed file back to the server.
Of course, the fact that Adobe does not support working across a network does not necessarily mean it won't work. It should.
Adobe's position is that there are too many variables in a network environment for them to guarantee that everything will work correctly in every network, especially given the fact that if something does not work properly, it's probably the network's fault, and Adobe has no way of troubleshooting your network.
If you can't work locally, you are on your own, and if something happens, you're on your own. If you must work from a server, make sure your network administrator is a competent professional.
When problems arise, a lot of valuable work can be lost.

Photoshop suddenly does not print to Epson 3880 - PROBLEM: Cannot print from Photoshop After restart error message appears: - "There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopen

PROBLEM: Cannot print from Photoshop
After restart error message appears:
— “There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopened any documents.”
• All print commands are greyed out and unavailable — even to call up the printer commands cannot be done.
The printer printed fine until about 2 weeks ago when this error message appeared. Printing continues from Pages, I-photo, preview etc. — only Photoshop fails.
The printer has been turned on and off, as have open documents been closed and open etc.. Preferences reset. Repeatedly I have read through blogs and forums and attempted to contact Adobe — all without results
Epson support struggled to find reason and several solutions were tried and they assume this is an Adobe problem.
Running Mac Powerbook X 10.10.2 / Photoshop CS6 13.0.6.x64
Attempting unsuccessfully to print to Epson 3880
What Adobe support will be of help.
Robert Darling — 2/19, 20, 21,22,23/2015

Probably best to ask in Photoshop General Discussion
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

Just installed update10.6.8 on my imac restarted and opened safari i have little snitch, it said xdefender wants to connect with apple, i let it. but after think has a malware been installed and update rooted it out? kindly advise

ust installed update10.6.8 on my imac restarted and opened safari i have little snitch, it said xdefender wants to connect with apple, i let it. but after i thought has a malware been installed and os update rooted it out? kindly advise

i have this sorted, a misunderstanding it was not xdefender trying to connect with apple it was XProtect Updater from apple.
jcher

IPM server Repository error issue..

Hi All,
We are using Invoice gateway for one opf our projects.
I could able to scan the hard copy and cretae a bacth.
OFR is creting the pdf, xml and txt file out of the scanned copy and keep it in a folder, so that IPM process them from then on.
Once IPM processes it and invoke BPEL for further action.
But IPM is throwig me the below error:
[2012-05-09T15:32:49.785+05:30] [IPM_server1] [ERROR] [TCM-00162] [oracle.imaging.agents] [tid: [ACTIVE].ExecuteThread: '2' f
or queue: 'weblogic.kernel.Default (self-tuning)'] [userId: <anonymous>] [ecid: 0000JSkzo^l5Ifs6wjZf6G1FeZj900000E,0] [APP: i
maging] [dcid: f05c270b0bae50db:-392a3bea:13730f9cd54:-7ff2-0000000000000d86] Failed to load Batch for new filing.
[2012-05-09T15:32:49.793+05:30] [IPM_server1] [ERROR] [TCM-00157] [oracle.imaging.agents] [tid: [ACTIVE].ExecuteThread: '2' f
or queue: 'weblogic.kernel.Default (self-tuning)'] [userId: <anonymous>] [ecid: 0000JSkzo^l5Ifs6wjZf6G1FeZj900000E,0] [APP: i
maging] [dcid: f05c270b0bae50db:-392a3bea:13730f9cd54:-7ff2-0000000000000d86] [arg: /u03/oracle/Middleware/user_projects/doma
ins/BBECM_DOMAIN/IPM/InputAgent/Input/Stage/TestCase_Invoice_316_204_09052012.txt] An error occurred filing file /u03/oracle/
Middleware/user_projects/domains/BBECM_DOMAIN/IPM/InputAgent/Input/Stage/TestCase_Invoice_316_204_09052012.txt.[[
oracle.imaging.ImagingException: TCM-00787: A repository error occurred.
faultType: SYSTEM
faultDetails:
ErrorCode = oracle.stellent.ridc.protocol.ServiceException, ErrorMessage = Unable to execute service IPM_LIST_IMAGI
NG_AGENTS and function QuserSecurityAttributeByType.
The error was caused by an internally generated issue. The error has been logged.
at oracle.imaging.repository.ucm.UcmErrors.convertRepositoryError(UcmErrors.java:128)
at oracle.imaging.repository.ucm.UcmAgentUserManager.getAgents(UcmAgentUserManager.java:77)
at oracle.imaging.repository.ucm.UcmAgentUserManager.ensureAgentUserPermissions(UcmAgentUserManager.java:29)
at oracle.imaging.repository.ucm.UcmRepositoryManager.connect(UcmRepositoryManager.java:411)
at oracle.imaging.repository.RepositoryManagerFactory.getInstance(RepositoryManagerFactory.java:172)
at oracle.imaging.repository.RepositoryManagerFactory.getInstance(RepositoryManagerFactory.java:57)
at oracle.imaging.repository.RepositoryManagerFactory.getInstance(RepositoryManagerFactory.java:91)
at oracle.imaging.application.ApplicationServiceImpl.getSingleApplication(ApplicationServiceImpl.java:516)
at oracle.imaging.application.ApplicationServiceImpl.getSingleApplication(ApplicationServiceImpl.java:467)
at oracle.imaging.application.ApplicationServiceImpl.getApplication(ApplicationServiceImpl.java:348)
at oracle.imaging.batch.BatchServiceImpl.loadApplication(BatchServiceImpl.java:348)
at oracle.imaging.batch.BatchServiceImpl.createBatch(BatchServiceImpl.java:70)
at oracle.imaging.inputagent.InputFilingMDB.loadBatch(InputFilingMDB.java:404)
at oracle.imaging.inputagent.InputFilingMDB.initializeFiling(InputFilingMDB.java:371)
at oracle.imaging.inputagent.InputFilingMDB.onMessage(InputFilingMDB.java:166)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.bea.core.repackaged.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:310)
nvocation.java:182)
n.java:149)
tionInterceptor.java:131)
nInterceptor.java:119)
n.java:171)
ptor.java:89)
n.java:171)
tionInterceptor.java:131)
nInterceptor.java:119)
n.java:171)
at com.bea.core.repackaged.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:204)
at $Proxy242.onMessage(Unknown Source)
at weblogic.ejb.container.internal.MDListener.execute(MDListener.java:466)
at weblogic.ejb.container.internal.MDListener.transactionalOnMessage(MDListener.java:371)
at weblogic.ejb.container.internal.MDListener.onMessage(MDListener.java:327)
at weblogic.jms.client.JMSSession.onMessage(JMSSession.java:4659)
at weblogic.jms.client.JMSSession.execute(JMSSession.java:4345)
at weblogic.jms.client.JMSSession.executeMessage(JMSSession.java:3821)
at weblogic.jms.client.JMSSession.access$000(JMSSession.java:115)
at weblogic.jms.client.JMSSession$UseForRunnable.run(JMSSession.java:5170)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:528)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
erSecurityAttributeByType.
The error was caused by an internally generated issue. The error has been logged.
at oracle.stellent.ridc.protocol.ServiceResponse.getResponseAsBinder(ServiceResponse.java:125)
at oracle.stellent.ridc.protocol.ServiceResponse.getResponseAsBinder(ServiceResponse.java:101)
at oracle.imaging.repository.ucm.UcmResponse.<init>(UcmResponse.java:66)
at oracle.imaging.repository.ucm.UcmRequest.makeOneServiceCall(UcmRequest.java:397)
at oracle.imaging.repository.ucm.UcmRequest.makeServiceCall(UcmRequest.java:219)
at oracle.imaging.repository.ucm.UcmAgentUserManager.getAgents(UcmAgentUserManager.java:65)
... 41 more
Can anyone please let me know the solution for the this repository error issue.
I bounsed the IPM server, but it didnt resolve the problem.
Thanks in advance
Chandru

This seems to be an error due to mapping from IPM. It can be more clear if the text file and screen shot of work flow mapping is uploaded.
Regards,
Vikrant Korde

Error coming out of Workflow restart - Error:OBJECTS_OBJREF_NOT_ASSIGNED_NO

Hi all,
After restarting the workflow through SWPR we are getting an error message as per mentioned below.
Error coming out of Workflow restart - Error:OBJECTS_OBJREF_NOT_ASSIGNED_NO.
Kindly suggest what can be the possibility of the error. I scehduled the SWPR program in the background and passed some workflows and getting this error message in the background job. Kindly suggest.
Thanks,
Neslin.

I think you need to analyse the Workflow log and then try to restart. I think you might have to change the container element value in order to remove the error. Please check and act accordingly.
Thanks
Arghadip

Error issuing in MR8M: MSG No M8210

Hi Sap Gurus,
When we reversing the Invoic or cancel the Invoice and then we are getting as issue below
Error issuing document number: RE_BELEG 01 2011
MSG N0 : M8210
Here I have checked the number ranges for invoice doc type RE. Evrey thing is fine and recently we implemented the SD module. so is this something to do with SD? let me know your suggetions on this.
Thanks,
Raj.

Dear Raj,
Go to T-Code SNRO, there enter RE_BELEG and click on number ranges--> Click on intervals, please check wether you have maintained number range for 01 FY 2011, if not then please maintain the same.
Hope this helps..
Br,Vivek

Spacebar freeze & IMac restart?

I was typing an email (Eudora) on my new, one month old intel iMac. Suddenly the spacebar wouldn't work (no space made when clicking on it). I hit the return key. The other keys worked. I tried the spacebar again. And again! Suddenly the computer restarted on its own. What the???? What happened?? Nothing else went out. I had Eudora open. TextEdit and Safari were running in the background. I ran Disk Utility & verified disk. Says all is fine. But if all were fine, why the sudden spacebar freeze and iMac restart?

To Stop Windows Opening on Start Up
System Preferences > General > uncheck Restore windows when Quitting and Re-opening Apps
You may also find this Link of Interest...
Managing Mac OS X Lion's application resume feature

I am getting this message from iTunes on my iMac: An error occurred while contacting the radio tuning service. Check your Internet connection, or try again later. Can't find a way to fix this. anyone hae any suggestions?

Question: I am getting this message from iTunes on my iMac:
An error occurred while contacting the radio tuning service. Check your Internet connection, or try again later.
Can't find a way to fix this. Does anyone have any suggestions?

Yeaaaah... I just powered up my G3 iMac... iTunes 7 on there... My iTunes on there can't do much. But it's still subscribed to one podcast that's still valid and working. If I try to use the radio, I get this message. I wager they changed urls and the like in the background years ago and this is just so old there's no longer any support for it.

IMac Restart error issue

Similar Messages

Maybe you are looking for