IMac wont start up after upgrade to Mavericks

I installed Mavericks as an upgrade to OS X 10.6.8 on my iMac and with in a half an hour of use my computer froze, I have tried all the normal rebooting techniques but my opening screen still has the vertical green stripes, even after using the disk repair/first aid utility, the iMac freezes without fully booting. the disk repair found no issues and says all is OK.

Hello Tone56,
It sounds like you are unable to successfully boot your computer after upgrading to Mavericks, and are seeing some graphical anomolies on startup. I recommend starting by resetting your PRAM with this article:
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
Note: To print these instructions, open Help Viewer’s Action pop-up menu (looks like a gear), then choose Print.
Shut down your Mac.
Locate the following keys on the keyboard: Option, Command (⌘), P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on your Mac.
Immediately press and hold the Option-Command-P-R keys. You must press this key combination before the gray screen appears.Continue holding the keys down until your Mac restarts, and you hear the startup sound for the second time.
Release the keys.
Resetting PRAM may change some system settings and preferences. Use System Preferences to restore your settings.
Then reset your SMC:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ht3964
Resetting the SMC for Mac Pro, Intel-based iMac, Intel-based Mac mini, or Intel-based Xserve
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
If the issue persists, try performing a Safe Boot then restart as normal to see if that will allow you to boot normally:
OS X: What is Safe Boot, Safe Mode?
http://support.apple.com/kb/ht1564
Starting up in Safe Mode
To start up into Safe Mode (to Safe Boot), follow these steps.
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key.
The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple logo and the progress indicator (looks like a spinning gear).
After the logo appears, you should see a progress bar during startup. This indicates that your computer is performing a directory check as part of Safe Mode.
To leave Safe Mode, restart your computer without holding any keys during startup.
Thank you for using Apple Support Communities.
Cheers,
Sterling

Similar Messages

  • IMac became very slow after upgrading to Mavericks

    after upgrading to Mavericks my mac became very slow, i can´t do anything on it without waiting at least15 min. Does someone know what i can do to make it better?

    Mine too, I am really frustrated, since I read all reviews and asked some friends and co-workers about mavericks, they are all happy, but my macbook is almost useless now.
    I tried using Mackeeper, but then apple says it´s a malware, so there´s my solution....
    Anyone with a good answer for this problem ???
    Is there a way to download Snow Leopard and do a clean install ??

  • IMac won't boot after upgrade to Maverick

    First off, I have a Time Machine backup, so I'm not in really deep hot water yet, but...
    Upgraded to Maverick from Lion 10.7.5 and let it run for ever and a day until it rebooted itself. Upon reboot, I got the grey screen with the Apple logo, then the little spinny thing beneath the logo disappeared...and nothing else happened. The iMac gets stuck like that and won't do anything else. I have only the keyboard and mouse connected to it — no external drives, no hubs, nothing else USB or FireWire. I can reboot to the recovery disk (which it now says is the 10.9 version). I have verified permissions, repaired permissions, verified disk (no problems) but repaired disk anyway, tried reinstalling Mavericks (and let it run overnight but got the exact same result) and even booted in single-user mode to run fsck. Nothing so far has worked.
    I'm stuck with a grey screen and the pretty Apple logo, but can't get to the login screen or do anything else with it. Suggestions?

    I spoke to Apple support and they've given me some suggestions to try when I get home tonight:
    Mac OS X: Gray screen appears during startup
    OS X Mavericks: Reset your computer's PRAM
    Intel-based Macs: Resetting the System Management Controller (SMC)
    Mac OS X: What is Safe Boot, Safe Mode?
    Resolve startup issues and perform disk maintenance with Disk Utility and fsck
    Mac OS X: Starting up in Safe Mode
    Startup key combinations for Intel-based Macs

  • Imac wont start up after new RAM, no chime, black screen

    Hi, I've recently purchased a used 2010 iMac i3 that had faulty RAM.
    This was confirmed as the issue when I tested a friend's original RAM from the same age iMac and the machine worked perfectly.
    I then ordered 2x 4gb Crucial memory (upgrade from the 2x 2gb already installed) but kept getting kernal errors and RAM integrity check errors so the modules were returned and replaced by crucial.
    Prior to returning, I attempted to reinstall a fresh copy of mavericks, but the hard drive failed to completely format, and then the OS install also failed so the machine currently now has no operating system. However before returning the ram the machine would boot up and connect to the internet to attempt to download the OS again.
    The replacements have now arrived, but after installing the machine won't even boot. First attempt to start there is a drive noise, and the fans run, but no chime and a black screen. If I force shutdown and try again the drive noise happens twice and the fans run, but the same outcome.
    If I remove the RAM I still get the single bleep, and once of all of the times I've removed and reseated the RAM I've had a triple beep integrity check fail.
    Any help would be massively appreciated. Lost now as to whether the issue is with crucials RAM or the iMac itself.
    Thanks

    Do you still have the old ram? Was orig sticks of ram bad? What happens if you put only one stick of the orig ram back in ?

  • IMac wont start up after power shortage

    Hi !
    yesterday I had a sudden power outage in my apartment while my iMac (September 2010) was running. Now it won´t start when I press the power button. Any suggestions?

    Zap the PRAM and Reset the SMC, then try again.
    If no go, contact Apple Service, iMac Service or Apple's Express Lane. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you're eligible for onsite repair since yours is a desktop machine.

  • Imac wont start up after power failure

    i moved the table my imac was on and i accidentally took off the power cable.the imac was on so when i took the cable off it shut off. then i put the cable back and tried to turn it on but nothing happened..it is like dead. any suggestions?

    Also, there is a small battery or capacitor on the logic board that may need to be replaced, as this has been the cause of a similar issue over many generations of Mac computer hardware. Of course there are other causes of failure, and that is why the help of an expert to troubleshoot and diagnose issues to attempt to resolve them can take time.
    And it may not be resolved after the first attempt if the actual problem is deeper than first best educated guess arrived by troubleshooting. Part of some repairs requires replacement of suspect parts, even if they may not be the cause, to eliminate their being within the realm of possibility. A good read is among the original Apple Technical Service Manuals, those aren't often available to the general public. I used one to self-troublehoot an iMac under AppleCare after the nearby 200+ miles one-way distant 'specialist' could not fix my new iMac, four times. So I am a bit cool on newer Macs; the way I see it one new headache lasting 10 months and requiring 3,000 miles travel, to not be resolved by experts (and under warranty, so I can't touch it!?!) is enough.
    The best cure for main power failure, is to have a good high quality battery backup system in place with automatic voltage regulation, that also works as a power filter; and can step in to isolate the Mac from mains high-or-low power fluctuation. This can save many products from bad power sources; do not rely on these, either. Make copies of your work ahead of time. This saves your computer from issues you can prevent.
    PS: my Macs seldom are shut off, for up to 11 months, some of mine only get to sleep when not in use. When the main power goes offline, during a storm or extended utility failure of their own making, I will have to shut them off as a choice. There is software in the UPS unit that can help shut down automatically, and that is a choice, too. I usually find their software problematic on occasion; and the battery backup is not very long in duration, so one with a few hours runtime and a method of rationing the power if you are present when the mains fail, is helpful in performing a normal shutdown after a power failure.
    Good luck & happy computing!

  • Magic Track Pad disconnecting after upgrading to Maverick

    My magic track pad has worked flawlessly since purchased with my iMac in 2011. After upgrading to Mavericks it now randomly disconnects and is scrolling in reverse. In order to get it working all I need do is turn on the mouse and when it connects, then the magic track pad reconnects. Why it will only reconnect after doing that, I have no idea ? The new reverse scrolling action is also a mystery. Help please ! 

    Hello Frank,
    It can be difficult to accomplish much if your Magic Trackpad does not stay connected.  I found an article with steps you can take when you have issues with a Bluetooth device not connecting.  I recommend following the steps in the section titled "Top troubleshooting tips" in the following article:
    Bluetooth Quick Assist
    http://support.apple.com/kb/ht1153
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked?

    My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, I call apple support and they told me to bring it in but the nearest store is about two hours away. They said I need it to erase my hard drive but I have too many family pics on it.
    would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked on it? I could replace the internal and get an enclosure for the original until I get the pics out of it?
    Please advise, it's like five years of family pics I don't wanna loose them and I am worried.
    Thanks
    Al Florez

    A Brody,
    I really apprecate your very quick respond, Its too late to back up as of now, my hard drive wont load at all so I cannot follow your instruction to back it up. Learn a hard lesson but I will from now on following your link.
    Also my hard drive it is not available to do the free exchange program.
    I read the OWC instruction on how to replace the drive I was just wondering if the 2TB would work on it instead of the 1 TB they offer, I specifically asked for the Seage Barracuda because I had great experiences with it on PCs.
    Again, Thank you

  • After upgrading to Mavericks my iMac does not see Sony camcorder in iMovie anymore. It still works on MacBook, so nothing wrong with camera or connections.

    After upgrading to Mavericks my iMac does not see my Sony camcorder anymore. I tried the new iMovie as well as the old version 9.0.9, which is still in Applications. I checked the camcorder and connections in iMovie on my MacBook (not upgraded) and that still functions properly, so the problem does not seem to be in iMovie, old or new, or in camcorder and connection.
    Anybody with the same problem or a solution?
    Thanks mbkom

    Try this

  • Why does the migration wizard run every time I start up my mac after upgrading to mavericks ?

    After upgrading to Mavericks, I log in as normal but then a migration wizard starts up asking me where I want to import data from and create new accounts. Why and how do I stop it ?

    It could be part of OS X's Resume feature. Any app that is open at shutdown will re-open on boot unless the tick in the following image is deselected when shutting down/restarting:
    Also check that Migration Assistant isn't listed in System Preferences>Users & Groups>Login Items.

  • After upgrading to Mavericks, all of my contacts disappeared. Did a "contacts archive" export and the file is 17mbs. Looks like there's data, but none of it at all displays. What gives? 20" iMac, early '09

    After upgrading to Mavericks, all of my contacts disappeared. Did a "contacts archive" export and the file is 17mbs. Looks like there's data, but none of it at all displays. What gives? 20" iMac, early '09

    After upgrading to Mavericks, all of my contacts disappeared. Did a "contacts archive" export and the file is 17mbs. Looks like there's data, but none of it at all displays. What gives? 20" iMac, early '09

  • After upgrading to Mavericks, I seem to have lost everything in my Outlook for imac 2011.

    after upgrading to Mavericks, I seem to have lost everything in my Outlook for imac 2011.
    all my email accounts, all my emails, all my folders & subfolders (received & sent) ... everything.
    help!

    Remove Adobe plug ins if any.
    Macintosh HD > Library > Internet Plug-ins
    AdobePDFViewNPAPI.plugin
    AdobePDFView.plugin

  • Preview won't start after upgrade to mavericks

    After Upgrading to Mavericks this afternoon (30th Oct 2013, 1420hrs)
    - i face the following problems. (there could be more problems that i may not have found out yet)
    1.
    The Preview application cant start.
    when i double click the prview applicaiton icn, the screen flashes momentarily, but nothing happens. the preview does not start.
    however, when i press the space bar, i can quick look at all the various file type such as *.pdf or *.jpg etc. but i can open it on preview.
    2.
    The same goes to the textEdit application - it does'nt start. the screen just flashes and nothing happens.
    3.
    When i click "Software Update.." from the Apple menu, nothing happens
    Up till now, I have a perfect smooth OS until i migrated to Mavericks.
    Please, can some one show me how can i solve these ?
    I cant open any of my pdfs and any of my txt files since i upgraded to mavericks...
    For you information :
    My current Mac Nook Air is:
    Software  OS X 10.9 (13A603)
    Any assistance from you all will be great.
    Thank you all...

    Back up all data. Quit Preview if it's running.
    Hold down the option key and select Go ▹ Library from the Finder menu bar. From the Library folder, delete the following items, if they exist:
              Containers/com.apple.Preview
              Preferences/com.apple.Preview.LSSharedFileList.plist
              Preferences/com.apple.Preview.SandboxedPersistentURLs.LSSharedFileList.plist
              Saved Application State/com.apple.Preview.savedState
    Log out and log back in. Launch the application and test.

  • I have a iMac that wont start up after it sits for a short time

    I have a iMac that wont start up after it sits for a short time. I changed out the hard drive and reinstalled Leopard. If I mess with it a little I can get it to start up usually by repairing the hard drive with another computer, one time I just held down the P-R-option and command keys and it worked. Once its on it will restart no problem but if it sits for and hour or so it will get stuck either in the grey screen or blue screen. I also pushed the smu button but didnt work. Please help? Thank you.

    For this type of question, we need to know which iMac you have. This forum covers G3, G4, and G5 iMacs that have different hardware, and any recommendations are better handled if people know which you have. For starters, do "About this Mac" from your Apple menu and look at teh processor type.
    You also need to tell us the version of the Mac OS you have, also avaiabe from "About this Mac.
    If the processor type says "Intel," you have a newer iMac that this forum covers and should report in the area for current iMacs here:
    iMac (Intel)

  • Intel imac wont start after changing permission

    intel imac wont start after i changed my hard drive permission to let me read and write, then i clicked apply to all enclosed files.i turned it off no problem. then it never started up again in os x. the grey screen with apple logo appears,then after a minute it restarts, and will keep doing that if i let it. i can start up in windows xp, but i dont know how to do anything in windows xp that will affect os x. i can use the hard drive in target mode, but i cant figure out how that can help me. i use a macbook to view target disk. ive spent hours looking through help and support. finally i do not have the os install disks. PLEASE HELP!

    My apologies for the inept instructions.
    Restart normally. Open Terminal in the Utilities folder. Paste the commands in the Terminal application to avoid typos:
    sudo su
    Press RETURN. Enter your admin password when prompted.  It will not be echoed to the screen. Press RETURN again. Now paste each of the following at the prompt and press RETURN after each.
    chown root:admin /Applications
    chmod 0775 /Applications
    chown root:admin /Library
    chmod 1775 /Library
    chown root:admin /System
    chmod 0775 /System
    chown root:admin /Users
    chmod 0775 /Users
    chmod -R -N /Applications
    chown -R :admin /Applications/*
    Again, my apologies.

Maybe you are looking for