IMAQ setup pattern matching 2 loaded with errors on the target and was closed

Hi , guys. has any of you nice people ever seen something like that ... in deployment progress?
labview 2010
sbRIO -9631
Thanks in advance.
Attachments:
deployment progress.jpg ‏43 KB

Hi, Oli
thanks for your help. I re-installed the IMAQ software, it seems working.
but i have some similar errors now, and i dont know which module i should re-install, could you tell me where the problem is, please.
the name of which module would be great.
thanks a lot.
Attachments:
0.jpg ‏55 KB
1.jpg ‏52 KB
2.jpg ‏52 KB

Similar Messages

Get message "loaded with errors on the target and was closed" but there are no errors in the vi.

Hi,
Attached image shows the error message which i receive when I try to run my vi. "vi loaded with errors on the target and was closed"
The vi has no errors as far as I can see and hasn't changed since I ran it a few days ago and it functioned fine. other vi's in the project run without any issue.
Any guidance to find the issue would be greatly appreciated!
Thanks,
Conor
Attachments:
Labview error.JPG ‏43 KB

Some tips:
1. Try to recompile the VI which is "loaded broken" (ctrl+click on Run arrow). Deploy.
2. Try to recompile this VI and its dependencies (ctrl+shift+click on Run arrow). Deploy.
3. Try to recompile top-level VI and its dependencies. Deploy.
4. Change something in "loaded broken" VI (add some code, like reversing array back and forth, just to make LV recompile it). Deploy.
5. Close the project. Restart RIO. Open project. Deploy.
6. Close LabVIEW. Restart computer. Restart RIO. Open project. Deploy.
7. Take another computer. Deploy from it.
8. Close project. Clear compiled object cache (menu Tools -> Advanced -> Clear compiled object cache...). Open project. Wait until LV will open/recompile it. Deploy.
9. Do as 7, but in the meantime reformat RIO from MAX. Open project. Deploy.
10. Contact NI Support. Send them your project. Make them Deploy it.
The fun starts when you have project which deploys for 30 minutes... Usually I skip straight to step 8 then, and usually it helps.

.vi loaded with errors on the target and was closed

When I intend to run my RT (communicating with an FPGA on a cRIO) it only runs one time. The second trial leads to the following error:
NI_AALBase.lvlibine Wave.vi loaded with errors on the target and was closed.
LabVIEW: Failed to load shared library lvanlys.*ineWaveCIN:C on RT target device.
After reseting the FPGA and Labview it runs again, but also only for one time.
Thanks for solutions!
Thomas Vogl

Error 'found'.
Process (one day working on it!):
1- 'Disabled' .vi cutting it into small pieces.
2- Locate code that provokes 'not defined error' by enabling and running.
3- Finally located.
My case:
I've designed a communication system. To send data uses a PDU containing a 'variant' and 'ring'. This ring indicates type of data to convert variant with necessary typedef. The system defines 4 default msgs on ring (NULL, ACK, NACK, PING).
The receptor works well, but as I have a lot of data types, I need a case structure. (rings do not work with case at least on 2011) Then I do next thing:
Explicit cast to a typedef enum with all my data values... (This system is designed for our purposes and could not be the better solution)
... UNDEFINED ERROR ON PXI ...
Solution:
Instead using explicit typecast use "coercion dot" casting. Like here.
I receive an U16 data that PXI cast to my enum on 'data out' indicator (you can't see coercion dot because pink and red are 'very different' colors)
No more errors.
Conclusions:
Labview has issues working with explicit type-casting to enums. I can't work more on it, but is necessary to debug this kind of issues because can affect projects at last steps of the development and drives LVdevelopers crazy.
The only think I do with the enumeration is to add new element and all the system fails...
Thank you for your reply Schmitz!
I hope that this information could help somebody that in the future needs to investigate how LV works... xD
Probably this is not the only issue related with ".vi loaded with errors on the target" (known as the "well defined error").
Cheers

SSRS Reporting manages goes down frequently. ERROR: The underlying connection was closed: An unexpected error occurred on a send.

We have been experiencing issues with SSRS over the past 5 weeks, the service goes down frequently. And it comes up only on reboot of the server.
We had also disabled the On Access scan in Mcafee.
The service is in use for about two years, and the below error started occuring over the last few days. Please advise on this.
ui!ReportManager_0-2!24e8!08/14/2014-18:13:45:: e ERROR: The underlying connection was closed: An unexpected error occurred on a send.
ui!ReportManager_0-2!24e8!08/14/2014-18:13:45:: e ERROR: HTTP status code --> 500
-------Details--------
System.Net.WebException: The underlying connection was closed: An unexpected error occurred on a send. ---> System.IO.IOException: Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host. ---> System.Net.Sockets.SocketException:
An existing connection was forcibly closed by the remote host
   at System.Net.Sockets.Socket.Send(Byte[] buffer, Int32 offset, Int32 size, SocketFlags socketFlags)
   at System.Net.Sockets.NetworkStream.Write(Byte[] buffer, Int32 offset, Int32 size)
   --- End of inner exception stack trace ---
   at System.Net.Sockets.NetworkStream.Write(Byte[] buffer, Int32 offset, Int32 size)
   at System.Net.PooledStream.Write(Byte[] buffer, Int32 offset, Int32 size)
   at System.Net.ConnectStream.WriteHeaders(Boolean async)
   --- End of inner exception stack trace ---
   at Microsoft.SqlServer.ReportingServices2005.RSConnection.GetSecureMethods()
   at Microsoft.ReportingServices.UI.Global.RSWebServiceWrapper.GetSecureMethods()
   at Microsoft.SqlServer.ReportingServices2005.RSConnection.IsSecureMethod(String methodname)
   at Microsoft.SqlServer.ReportingServices2005.RSConnection.ValidateConnection()
   at Microsoft.ReportingServices.UI.Global.SecureAllAPI()
   at Microsoft.ReportingServices.UI.ReportingPage.EnsureHttpsLevel(HttpsLevel level)
   at Microsoft.ReportingServices.UI.ReportingPage.ReportingPage_Init(Object sender, EventArgs args)
   at System.EventHandler.Invoke(Object sender, EventArgs e)
   at System.Web.UI.Control.OnInit(EventArgs e)
   at System.Web.UI.Page.OnInit(EventArgs e)
   at System.Web.UI.Control.InitRecursive(Control namingContainer)
   at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
ui!ReportManager_0-2!24e8!08/14/2014-18:13:46:: e ERROR: Exception in ShowErrorPage: System.Threading.ThreadAbortException: Thread was being aborted.
   at System.Threading.Thread.AbortInternal()
   at System.Threading.Thread.Abort(Object stateInfo)
   at System.Web.HttpResponse.End()
   at System.Web.HttpServerUtility.Transfer(String path, Boolean preserveForm)
   at Microsoft.ReportingServices.UI.ReportingPage.ShowErrorPage(String errMsg) at    at System.Threading.Thread.AbortInternal()
   at System.Threading.Thread.Abort(Object stateInfo)
   at System.Web.HttpResponse.End()
   at System.Web.HttpServerUtility.Transfer(String path, Boolean preserveForm)
   at Microsoft.ReportingServices.UI.ReportingPage.ShowErrorPage(String errMsg)
library!ReportServer_0-1!1c90!08/14/2014-18:13:51:: Call to ListParentsAction(/Data Sources).
library!ReportServer_0-1!1c90!08/14/2014-18:13:51:: Call to ListParentsAction(/Data Sources).
library!ReportServer_0-1!1c90!08/14/2014-18:13:51:: Call to ListChildrenAction(/Data Sources, False).
webserver!ReportServer_0-1!1c90!08/14/2014-18:13:51:: i INFO: Processed folder '/Data Sources'
library!ReportServer_0-1!68c!08/14/2014-18:13:56:: Call to GetItemTypeAction(/).
library!ReportServer_0-1!68c!08/14/2014-18:13:56:: Call to ListParentsAction(/).
library!ReportServer_0-1!68c!08/14/2014-18:13:56:: Call to ListChildrenAction(/, False).
webserver!ReportServer_0-1!68c!08/14/2014-18:13:56:: i INFO: Processed folder '/'

Hi SThiyag,
Based on your error message, it may be related to the “SecureConnectionLevel” in the RSReportServer.config file. Please go to C:\Program Files\Microsoft SQL Server\MSRS11.MSSQLSERVER\Reporting Services\ReportServer, use Notepad to open the RSReportServer.config,
modify <Add Key="SecureConnectionLevel" Value="0"/>, change the value into "1" or "2".
(Note: Please backup the file before modify it.)
Acceptable values are:
3 Most secure—Use SSL for absolutely everything.
2 Secure—Use SSL for rendering and methods that pass credentials but don't insist on it for all SOAP calls.
1 Basic Security—Accepts http but rejects any calls that might be involved in the passing of credentials.
0 Least Secure—Don't use SSL at all
Here is a blog for error message "The underlying connection was closed...", please refer to the link below:
http://blogs.msdn.com/b/engelsr/archive/2005/11/29/the-underlying-connection-was-closed.aspx
If you have any question, please feel free to ask.
Best Regards,
Simon Hou

Page opening hangs ,and loads with errors

page opening hangs ,and loads with errors,
terry.

Terry,
You need to be much more descriptive when posting. We have no idea what "page" you are referring to.

NeeBeans - Form loaded with errors

Using NetBeans 6.00 Windows.
I created a form class extending JPanel and inserted the class in Palette.
public class ObjPrivUser extends javax.swing.JPanel Then, I created a second class extending JPanel, including the first class.
public class GrantsByUser extends javax.swing.JPanel {
private void initComponents() {
objectPrivUser = new ObjPrivUser(db);
private GUI.Panels.ObjPrivUser objectPrivUser;
...Everything was ok, when I open the second class I can visualize all components. Until yesterday, when I opened the class and receive a message "form loaded with errors".
I recreated both classes, but today the same error has occurred.
Any sugestion?
Xks,
Fornari

Recompile from your source, something is not nice in your file.

Loadlibrary failed with error 126 the specified module could not be found

Hello i get this error message at random when am using oracle sql developer, sometimes it comes right after startup, and some times after 5 mins.
the error closes down the program
please help

Searching the web for "loadlibrary failed with error 126 java" seems to point to issues with OpenGL and certain video drivers and/or environments with multiple monitors. Here are several discussions...
https://netbeans.org/bugzilla/show_bug.cgi?id=243153
Error "LoadLibrary failed with error 126: The module could not - Microsoft Community
[SOLVED] Issue with Technic Launcher: Load Library failed with Error 126 - Technic Launcher - Technic Forums
So it seems this issue is not specific to SQL Developer. The last discussion includes a video link in its last post saying that ".dll" is searched for rather than "atioglxx.dll" on 32-bit systems or "atio6axx.dll" on 64-bit system (in the C:\Windows\system32 folder), so a workaround is to copy one of those to ".dll".

Backups failing with error 19: the backup disk could not be resolved, or there was a problem mounting it

Hello all,
Doubt this issue relates to a recent and ugly issue but sharing anyways (resolved thanks to a user here: LaPastenague)
Time Capsule won't backup if Modem (Motorola SB6121) attached
This was on Feb 10th resolved. Few days later I upgraded to Yosemite. Backups were working fine since.
Yesterday I happen to notice my last backup was 5 days ago. I looked in the console logs and saw:
2/25/15 3:55:06.127 PM com.apple.backupd[2777]: Attempting to mount network destination URL: afp://Paul;AUTH=SRP@Time%20Capsule._afpovertcp._tcp.local./Data
2/25/15 3:55:17.778 PM com.apple.backupd[2777]: NAConnectToServerSync failed with error: 2 (No such file or directory) for url: afp://Paul;AUTH=SRP@Time%20Capsule._afpovertcp._tcp.local./Data
2/25/15 3:55:17.792 PM com.apple.backupd[2777]: Backup failed with error 19: The backup disk could not be resolved, or there was a problem mounting it.
2/25/15 3:57:18.808 PM com.apple.prefs.backup.remoteservice[2021]: Attempt to use XPC with a MachService that has HideUntilCheckIn set. This will result in unpredictable behavior: com.apple.backupd.status.xpc
I called Apple. Their front line was clueless. He suggested resetting the TC (latest "tower" model btw") which then a backup kicked off YEAH
But the next hour it failed
Called Apple again, this time to Sr Advisor. He suggested factory reset of the TC and set up again. Also first backup worked then rest failed
Third call to Apple useless also. He was asking questions I didn't feel relevant. He also was asking me to reset the TC which I told him was done 2 hours prior. He asked me to reboot which I could NOT at that time.
I begged him to collect data to submit to engineering, which will take days to get a reply.
So I thought I would throw this out to the community....
TC Is NEW (replaced from last issue). Mac is 8 months old (iMac 27"), Os is Yosemite, TC also new (latest model)
Thanks...

Yosemite is problematic on two fronts.. Networking and Time Machine.. so the combo of doing both with a Time Capsule is like bugs on bugs.
Here is my standard list.. but your problem maybe difficult to resolve.. and my suggestion is simple.. until Apple get their act together and fix TM.. buy Carbon Copy Cloner and use that for your backup. It is solid and reliable.. even better if you use USB drive plugged into the computer and do a bootable clone.. because then you have a backup that is able to be tested for full functionality 2min after the end of the backup.
This also starts from a factory reset.. but the reason for it is to change the configuration which is much more easily handled with factory reset to begin.. the instructions are there.. because this is my standard reply.. this is not uncommon!!
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
ie Start from a factory reset. No files are lost on the hard disk doing this.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 and TCwifi for basestation and wireless respectively.
Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking. If the TC is main router it will not be an issue.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric.. but this change will mess up your TM backup.. so be prepared to do a new full backup. Sorry.. keep this one for second round if you want to avoid a new backup.
5. Mount the TC disk in the computer manually.
In Finder, Go, Connect to server from the top menu,
Type in SMB://192.168.0.254 (or whatever the TC ip is which you have now made static. As a router by default it is 10.0.1.1 and I encourage people to stick with that unless you know what you are doing).
You can use name.. SMB://TCgen5.local where you replace TCgen5 with your TC name.. local is the default domain of the TC and doesn't change.
However names are not so easy as IP address.. nor as reliable. At least not in Yosemite they aren't. The domain can also be an issue if you are not plugged or wireless directly to the TC.
6. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
You might need to do some more work on the Mac itself. eg Reset the PRAM.. has helped some people. Clean install of the OS is also helpful if you upgrade installed.
Tell us how you go.
Someone posted a solution.. See this thread.
Macbook can't find Time Capsule anymore
Start from the bottom and work up.. What I list here is good network practice changes but I have avoided Yosemites bug heaven.
This user has had success and a few others as well.
RáNdÓm GéÉzÁ
Yosemite has serious DNS bug in the networking application.. here is the lets say more arcane method of fixing it by doing a network transplant from mavericks.
http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.

I am experiencing this error with one of our cluster environment. Can anyone help me in this issue.
The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.
Thanks,
Venu S.
Venugopal S ----------------------------------------------------------- Please click the Mark as Answer button if a post solves your problem!

Hi Venu S,
Based on my research, you might encounter a known issue, please try the hotfix in this KB:
http://support.microsoft.com/kb/928385
Meanwhile since there is less information about this issue, before further investigation, please provide us the following information:
The version of Windows Server you are using
The result of SELECT @@VERSION
The scenario when you get this error
If anything is unclear, please let me know.
Regards,
Tom Li

HT204406 stuck on "matching your music with songs in the itunes store", help.

i just purchased iTunes Match.
step 1 - Gather information about your iTunes libarary = no problem
step 2 - Matching your music with songs in the iTunes Store = problem
step 2 seems to be stuck (for 2 hours) at 2161/18117
any help on explaining why it's stuck?

Hi,
This is a post from over 2 yrs ago.
However, there is an ongoing issue which I believe Apple have not acknowledged yet.
Jim

I cannot open files in excel with error message "The file name or path contains invalid characters

I cannot open files in excel with error message "The file name or path contains invalid characters

Found the solution. The hardrive name was changed to "/" which is not a recognised file path character. So I changed the name to "Mac" then I was able to already open all files in excel and word

Flash CS 6 error: CreateWinProcess failed with error 2 - The system cannot find the file specified

Hi,
I'm getting the error "CreateWinProcess failed with error 2 - The system cannot find the file specified" whenever I try to test an Air app within the Flash IDE.
This error even comes up with a new and empty project .fla file. I already updated the Air runtime and Flash to the latest version.
How to fix this problem? Any ideas welcome!
Thank you.

I installed the update, but I'm sorry to say that it did not solve the problem
The error is still there as described by Master §ix and Daniel777
CreateWinProcess failed with error 2. The system cannot find the file specified.
It happens when trying to test, debug, or publish air applications (AIR 2.5 – AIR 3.4 , desktop, android, iOS)
In this case, I can't use the simulator to test the applications,
thanks

Wrapper.createfile failed with error 3: The system can't find this path

Hi,
I have a problem of installing Java on my computer. I saw the error which is "wrapper.createfile failed with error 3: The system can't find this path specified."
I searched a lot of sites to solve it, but i havent found. How do I solve it ?
Thanks...

Hi,
Error code 0x80070003 = "The system cannot find the path specified."
Have you checked the log file smsAdminUI.log? Maybe it can give us some clues.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Register-SPWorkflowService error: The underlying connection was closed

I have a three server workflow manager farm. I'm using hardware load balancing across the three servers. I've associated a hostname in DNS with the VIP on the NLB.
When I run Register-SPWorkflowService and point at the hostname for the -WorkflowHostUri parameter, I get the error:
Register-SPWorkflowService The underlying connection was closed An unexpected error occurred on a receive.
If I put that URL into a browser on the SP machine where I'm running this cmdlt, it responds with the correct XML. So I know that the NLB is routing regular http requests to my machines in the quorum.
Also, if I use the actual machine name of one of the three machines in the workflow manager quorum, the cmdlt works.
I know very little about NLB hardware. Is there something I need to tell the guys configuring the NLB to do so that the connection doesn't close?

Yes, I actually had done that before using a host file entry to replace the DNS mapping from the NLB VIP to the IP of one of the machines in the WFM quorum. It worked from the standpoint of registering and SharePoint shows that the farm is "connected". However,
when I go to create an SP 2013 workflow, it still only shows 2010 workflows in the dropdown (in SPD.)
I also put Fiddler on the SharePoint machine that I'm using to register the WFM quorum to SharePoint. It shows that when the register cmdlt is executed, several calls to the
/SharePoint/ web service endpoint are made, initially getting a 401 asking for an authentication, and then after creds are passed, getting a 200. But then a call to
/SharePoint/$Activities is called and a 401 occurs twice, after which the registration cmdlt fails.

Error MSB4057: The target "PlatformPrepareForBuild" does not exist in the project._

Hi to all,
I tried to compile my .sln with VS2010 but I had this error.
error MSB4057: The target "PlatformPrepareForBuild" does not exist in the project.
It occurs only compiling with win32 configuration but not with x64 one.
Ideas?
Thank you in advanced

In which version of Visual Studio did you create this solution? And What type of the project in this solution? And could you please post the proj file here?
If this solution is created in VS2012 or VS2013, please make sure the original solution is not corrupt, it can be opened and built successfully in the corresponding Visual Studio. For probable compatibility issues, you could check the documents here:
Visual Studio 2012 Compatibility
Visual Studio 2013 Compatibility
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

IMAQ setup pattern matching 2 loaded with errors on the target and was closed

Similar Messages

Maybe you are looking for