IMAQdx Timeout Error 0xBFF6901B

Using IMAQdx with GigE camera, I get a
Timeout error 0xBFF6901B.
What is this error?

This is an old thread, but I had the same problem with a different solution.I had one working Basler Camera, and on non working Basler camera. Turns out I needed to disable test packets on the non working camera by this procedure:http://digital.ni.com/public.nsf/allkb/8D9A975B04F66B728625768900805A21 which states:The test packet timeout error can also be handled by configuring the Test Packets Enabled attribute for the camera to be disabled in Measurement & Automation Explorer (MAX). Follow these steps to set this attribute:
Open MAX.Click on the Basler GigE camera under Devices and Interfaces»NI-IMAQdx Devices.Choose the Camera Attributes tab.Click on View Options listed right above the camera attributes, and then choose to View All. This allows all camera attributes to be displayed.Click on Expand All to list all the attributes.Select the Test Packet Enabled attribute and set it to be disabled.7. SAVE THE CONFIGURATION That will generate a new error of 0xBFF60493 which will be fixed by this accepted solution:http://forums.ni.com/ni/board/message?board.id=200&message.id=26623&query.id=806694#M26623 which states:In MAX (Tools->NI Vision->Remote Image Options...) and turn off the option to "Display images on remote monitor." Message Edited by screamingmouse on 05-14-2010 06:52 PM

Similar Messages

Error -1074360293 (IMAQdx Timeout) after running acquisition for some time

My vision application in LabVIEW does several acquisitions and processings successful but then the acquisition (grab) suddenly fails with a timeout error (-1074360293, IMAQdx: Timeout). The error does not happen when only acquiring the images.
After the error happened no acquisition is possible. Even when LabVIEW is closed MAX returns a timeout error. Only rebooting helps.
some Hardware Details:
3 FireWire Controllers (1394a)
3 Cameras connected to the first two controllers, one to the third (7 cameras total)
Mode for all cameras: 1280 x 960 Mono 8 7.50 fps
The bandwidth for a FireWire controller is sufficient. (Three cameras on one controller run without any problem.)
The memory consume of the application is raising short before or after the error occurs. But I did not find out where exactly.
Before the error happens some minutes until one and half an hour pass.
More details will follow.
Is there a specialist in FireWire or in vision who can help?
Greetings,
shb
Solved!
Go to Solution.

Changing the driver to this one seems to solve the issue:
"OHCI-compliant 1394 Host controller (legacy)" (in German: "OHCI-konformer 1394-Hostcontroller (alt)")
With this driver the test has run for more than 66 hours without throwing an error.
Some related Articles:
http://www.rme-audio.de/forum/viewtopic.php?id=9827
http://www.myvideoproblems.com/ProblemPages/CannotCapture.htm

How to disable the Timeout error?

I can grab a image with my GigE camera, by using an external trigger.
But I am always getting the timeout error after the millisec. i set as timeout - how can I set the time infinite?
Thanx for ya help

Hi Mike,
thanx for the suggestion.
I am just starting with labview. that's why I trying the grab images with the measurement & automation explorrer.
under the acqusition attributes you can define the timeout in ms, and in my labview program i set the timeout with the help of the attribute knot(IMAQdx).
I tried to set it on "-1 ", but it didn't work.
I am going to look in all the attributes the knot offers, maybe I will find something that helps me.
vrupprecht

Imaqdx timeout

I installed IMAQdx as an addon for Labview. I managed to make it run but I am getting a timeout error (error 1074360293). The IMAQdx sign is placed in a while loop. Images start being produced after about 15 cycles and only last for 3 cycles before producing the timeout error mentioned above. How can I fix this?
Solved!
Go to Solution.

These are two attempts of the code. Thank you for your help
Attachments:
PIV1.png ‏114 KB
PIV2.png ‏111 KB

IMAQdx timeout with JAI camera in multicast mode

We have a camera from JAI connected to a GigE card, displaying the image within a LabVIEW program, and this has run reliably for months. We would now like to record the image for short periods of time as well. We've added a second computer on the GigE network to capture and record the image stream with a dedicated piece of software. We put the JAI camera into multicast mode so that both computers receive the same image. Now, we get timeout errors in the LabVIEW program: error -1074360293 at IMAQdx Get Image.vi. Increasing the timeout length to 10s (default is 5) didn't help. Any idea why IMAQdx doesn't work in multicast, but works properly in unicast? Is there some setting I've missed?
Solved!
Go to Solution.

Hi nathand,
It seems IMAQdx 3.9 added a bug that makes multicast mode not work properly (the camera is silently configured for unicast mode in certain cases -- internal CAR# 318906). Can you confirm if you are using this version or if you are using a previous version? If you are saying it works for a little bit of time but then fails I would assume it is _not_ this bug.
Do you know what type of switch you are using between the camera and the two PCs? If it is a managed switch it might be using IGMP snooping to determine which interfaces are listening to which multicast addresses. It is possible that a bug in the switch's implementation of this protocol might cause the association to drop after a while. You could possibly disable this snopping and either manually assign which multicast addresses are forwarded or have it forward to all ports.
Eric

1074360293 IMAQdx timeout

I need help with this error (-1074360293 IMAQdx timeout). This doesn't fail right away, but it runs for a while and then it fails and eventually LabVIEW will crash (close). I if run the VI by itself no error occurs, but when I implement that into the main program it will fail. I have windows 7 and it is updated to the latest. I searched in the NI discussion forum and it appeared that one person has experienced this issue before and he said that he changed host controller driver to Texas Instrument (TI) HOIC compliant IEEE 1394 and system worked fine. I don't know what is TI HOIC compliant IEEE 1394 and I don't know where to download it and how to install on my computer. If any of you know the solution, please help me out. Attatached is the VI that grabs images and saves to an AVI file.
Thank you very much.
Attachments:
GrabAndSaveAVIRevise.vi ‏99 KB

The problem has been found. I was not about the recording, but it was the screen shot after the recording (this step is on a separate VI that is called after the Recording VI). For now, i don't know what causes LabVIEW to crash, but I will run the screen capture VI alone to find out.
Thank you for your reply.
son

TimeOut error while running a report on the report server

Hi,
One of my report is taking 30 minutes to generate the output. It works fine when I run it locally, but when I run it on report server I encounter the following error message. Its a timeout error. Any solution other than tuning the query, please.
500 Internal Server Error
org.omg.CORBA.OBJECT_NOT_EXIST: minor code: 0 completed: No
     at java.lang.Class.newInstance0(Native Method)
     at java.lang.Class.newInstance(Class.java:237)
     at com.inprise.vbroker.orb.SE.read(SE.java:28)
     at com.inprise.vbroker.orb.DelegateImpl.handleReply(DelegateImpl.java:711)
     at com.inprise.vbroker.orb.DelegateImpl.invoke(DelegateImpl.java:606)
     at org.omg.CORBA.portable.ObjectImpl._invoke(ObjectImpl.java:459)
     at oracle.reports.server._ConnectionStub.getMainFile(_ConnectionStub.java:1283)
     at oracle.reports.client.ReportRunner.getMainFile(ReportRunner.java:488)
     at oracle.reports.rwclient.RWReportRunner.getMainFile(RWReportRunner.java:121)
     at oracle.reports.rwclient.RWReportRunner.getMainFile(RWReportRunner.java:95)
     at oracle.reports.rwclient.RWClient.runReport(RWClient.java:1322)
     at oracle.reports.rwclient.RWClient.processRequest(RWClient.java:1139)
     at oracle.reports.rwclient.RWClient.doPost(RWClient.java:328)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:283)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:336)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].server.http.ResourceFilterChain.doFilter(ResourceFilterChain.java:59)
     at oracle.security.jazn.oc4j.JAZNFilter.doFilter(JAZNFilter.java:283)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:523)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:269)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:735)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].server.http.AJPRequestHandler.run(AJPRequestHandler.java:151)
     at com.evermind[Oracle9iAS (9.0.2.0.0) Containers for J2EE].util.ThreadPoolThread.run(ThreadPoolThread.java:64)

Hi Bhasker
Try setting idleTimeOut under connection element in server configuration file to a large value.
Regards
Sripathy

Getting timeout error while updating a record from c#

Hi,
I have around 30k records in a tables. When I update that record inside the Transaction (Enterprise Data Library, c#) , it takes long time and throws timeout error.
But I am able to update the same record via Toad.
In the morning I tried same updating the record, it works without any change in the code or script.+
is it due table lock or db related issue? please adivse, how to resolve if occurs again.
anand

Code:
private static void Save()
using (DBTransactionManager dbTransactionManager = new DBTransactionManager())
try
DataTableDAL.Instance.ExecuteDML("Update Voyage SET BallastBonus = 30000 WHERE ID = 'AE53B610BEA743EC8AFBAED0C8349BF8';");
//commit database
dbTransactionManager.Commit();
catch
dbTransactionManager.RollBack();
throw;
Table
Column Name     ID     Pk     Null?     Data Type     Default     Histogram     Encryption Alg     Salt
ID     1     1     N     NVARCHAR2 (32)          None
CALCNUMBER     2          N     NUMBER (10)          None
CURRENCYID     3          N     NVARCHAR2 (32)          Frequency
CALCTYPE     4          N     NUMBER (5)          Frequency
ESTIMATEDESCRIPTION     5          Y     NVARCHAR2 (200)          None
ESTIMATEGROUPDESCRIPTION     6          Y     NVARCHAR2 (200)          None
BALLASTBONUS     7          Y     NUMBER (12,2)          None
BALLASTBONUSCOMMPCT     8          Y     NUMBER (6,3)          None
ISESTIMATE     9          N     NUMBER (1)          None
ADDITIONALSTEAMVALUE     10          Y     NUMBER (8,4)          None
ISADDITIONALSTEAMPCT     11          Y     NUMBER (1)          None
ADDITIONALPORTVALUE     12          Y     NUMBER (8,4)          None
ISADDITIONALPORTPCT     13          Y     NUMBER (1)          None
CREATEDBY     14          N     NVARCHAR2 (32)          Frequency
CREATEDDATE     15          N     DATE          None
UPDATEDBY     16          Y     NVARCHAR2 (32)          None
UPDATEDDATE     17          Y     DATE          None
LUMPSUMCARGOCOST     18          Y     NUMBER (1)          None
BUNKERPRICEMETHOD     19          Y     VARCHAR2 (30 Byte)          None
INCCONTCALCRESULT     20          Y     NUMBER (1)          None
FINAL_EST     21          Y     NUMBER          None
SPOT_VOYAGE     22          Y     NUMBER (1)          None
ISRUNCOSTEDIT     23          Y     NUMBER (1)          None
Index
Table doesnt have any index, except primary key index.
Total Records
35,000
Hope this input might sufficient to help me.

Open socket timeout error

Sometime I can write to the local shared variable through data socket. But sometime cannot. Even though, I still can read/write through shared variable monitor.
The error is in the open socket, said connect to peer timeout. I set timeout to 10s or left blank both not work.
I am using 8.2.1 on vista. The computer has 2 lan ports.
I met almost same case long time ago. I solved it by diable NETBIOS and one of the lan port.
This time, I disabled netbios already. But in vista, seems not able to disable the other lan port.
Any suggestion?

hi turbot,
I had same problem of timeout error.just check if system Firewall is on or off if it is on then make it off and then run the program.i don't know how much this will help you,it helped me.
GAK
Gaurav k
CLD Certified !!!!!
Do not forget to Mark solution and to give Kudo if problem is solved.

Why do i keep getting the "internet connection timeout" error message?

i have been upgrading a few standard itunes albums to itunes plus versions through my 3g mobile broadband connection, while not exactly a fast process, it was working fine until i started to get a backlog of 3 or 4 albums which were waiting in a queue to be downloaded, now every time i do the "check for downloads" option i get the "internet connection timed out" error message...this has been going on for 2 days! am i right in suspecting the backlog of albums is too much for my 3g mobile broadband connection? this is really doing my head in, if any of you techies could help me, it'd be much appreciated...?

yes i have recently updated to itunes 8.2.1, but i am starting to think its apple's servers (i tried to download at my brothers house...different computer and connection...same connection timeout error), because it will still let me download an album, but not necessarily all of the tracks. when i questioned itunes customer services about the seemingly hit and miss state of affairs with downloading, they told me to wait 3 weeks before trying to download the tracks that were giving me the grief (2 tracks from an arctic monkeys album)...which kinda indicates they know there is a problem and are trying to fix it, why else would they say wait 3 wks??? they gave me 5 free music tracks too, which is handy.

Frame timeout error using Configure Trigger3.vi

Hi all,
I'm triggering the frame capture of an .avi with an RTSI connection. However, I keep getting a frame timeout error when I use the IMAQ Configure Trigger3.vi. I don't get any timeout errors when I just use the IMAQ Generate Pulse3.vi but I am trying to sync the frame capture to an optical switch. If I just use IMAQ Generate Pulse3.vi, I get a .avi but the frames are completely out of sync with the switch, but if I use both IMAQ Generate Pulse3.vi and Configure Trigger3.vi I get nicely separated images but it takes an age and ends up in a timeout error.
I want to capture e.g. 500 frames, over the course of 2 s - so I've set my frame timeout to be 2000. At my current acquisition rate (31680 Hz per line (1024 pixels)) 500 frames corresponds to a total of 1.578 s (images are 100 pxls in height). This is much less than the total scanning time. Where am I going wrong?
Thanks in advance for your help.
Miika
Attachments:
screen.png ‏32 KB

Hey Miika
What are the hardware you are using. These vi's only work with specific hardware and this may be why they are not functioning correctly. For example the Configure trigger3 vi only works with the following PCIe-1427, PCIe-1429, PCe-1430, PCIe-1433.
Matthew Trott
Applications Engineer
National Instruments UK
www.ni.com/ask

Timeout error while running Report

Hi
All,
Windows 2000
Oracle Report builder 10g
Oracle developer suite 10g
when I had OLD computer i was able to run report more than 10 minutes. Now, I got NEW computer and i am getting TIMEOUT error while running report more than 10 minutes.
Any clue?
Thanks,
Vishal

As Fs says it depends on how you're running the report.
If you're running via a server then you need to make the change on that server or amend the URL you are using to run the report to add the enginereponsetimeout parameter.
You can amend this parameter on the server either by using the Application Server Control as I described in my last post or by directly editing the config file. This file will be called <reportservername>.conf and can be found in the oracle_home/reports/conf directory.
In this file look for the engine tag and see if the engineResponseTimeOut property is set.
E.g:
<engine id="rwEng" class="oracle.reports.engine.EngineImpl" initEngine="1" maxEngine="4" minEngine="1" engLife="50" maxIdle="20" callbackTimeOut="90000" engineResponseTimeOut="5">
</engine>
This value is in minutes so increase to a time larger than that it takes to run the report.
If instead you're running the report via Report Builder on your own PC then look for a file called rwbuilder.conf in the same location on your PC and make the same change as described above.
If this property isn't in the file then the engine isn't supposed to time out at all so the problem may well be something different. But to discount it try setting to a large value like 30.

Crystal report server2008 (XI R2): CMC session timeout error

HI
Crystal report server2008 (XI R2): CMC session timeout error
Accessing folders, scheduling reporting or running reports are working fine with Central Management Console (CMC) within the Crystal report server or accessing CMC within VPN machine. But when CMC is accessed through browser from client desktop i.e through proxy URL, users are not able to access folder or personal folders to view any reports even admin user is not able to access folders. When users try to access folder or personal folders it gives session-timeout errors. Within less than a 1 or 2 minutes it is showing session timeout error. Appreciates any one help on this quickly.
Regards,
Patrick Raths

Please post your query to the [Business Objects Enterprise Administration|BI Platform; forum. This forum is dedicated to development and deployment of .Net applications that connect and interact with BusinessObjects Enterprise, BusinessObjects Edge, or Crystal Reports Server. This includes the development of applications using the BusinessObjects Enterprise, Report Application Server, Report Engine, and Web Services SDKs.
BTW., if thi is an important issue, I'd recommend creating a phone case.
Ludek
Edited by: Ludek Uher on Aug 11, 2010 1:58 PM

Getting timeout error while executing my report

Hi experts,
I need to get data from a Ztable which is having more than 64 millions of records. That query itself is taking more than 20 min to execute. I have used package size while retrieving tha data but still taking same time to execute, Giving me the TIMEOUT error .
Provide some suggetions to use different types of SELECT quries that can be used to improve the performance.
Thanks & Regards,
Bhanu

Hi ,
I am working as an abaper for Service Management module.
I need to show the prmise details inthe output of alv. Before that i need to get the meter reading details and need to do some calculations, by which i need to show idle one (Here only i need to hit a ZTABLE which is having more than 64 million records). For that idle premise user can select multiple pemises by using check boxes and can create notification by pressing a pushbutton 'CREATE IS NOTIFICATION' which exist on the application toolbar . So i can not run this report in background.
Thanks & regards,
Bhanu.

Timeout error in ECC "INTERNAL.CLIENT_RECEIVE_FAILED Error while receiving by HTTP (error code: 402 , error text: ICM_HTTP_TIMEOUT)"

Dear Experts,
I am very critical situation due to this timeout error in ECC, please help me as much as you can. Go-live date is very near, but I am not getting any clue why this error is occurring. our ECC system is EHP 4, and PI is dual stack 7.4
My scenario is synchronous ABAP proxy to HTTP_AAE. request is triggering from ECC via proxy and reaching to third party (bank) through PI, I am reviving the response back in PI from bank. But from PI to ECC the response is not reaching. So in ECC after the defined Timeout limit its getting timed out.
I have tried everything by increasing the timeout in ECC more than 15 minutes in HTTP_TIMEOUT under SXMB_adm in ECC, but nothing worked, even if I am increasing for half an hour then also its getting timeout after half an hour.
response from bank to PI is coming within 30 to 40 seconds, but PI is not sending the response back to ECC.
This is classical scenario, and I have checked the trace via SXMB_Moni in PI as well as in ECC, in ECC its showing the timeout error, but in PI i did not see any trace for this error.
I have read many thread on SCN for the same error, and everywhere it has been suggested to increase the timeout, and I have tired that, it didn't help me.
All ABAP proxy configuration has been done as follows.
RFC destinations in ECC
LCRSAPRFC(TCP/IP)
SAPSLDAPI ((TCP/IP))
G type destination to path "/sap/xi/engine?type=entry"
G type destination SAP_PROXY_ESR to path "/rep"
All the destination connection test is working fine.
but i have a doubt on G type destination(AAE_XDJ) to path "/sap/xi/engine?type=entry" which is returns the status code 500 with message "Empty HTTP request received", is it ok with 500 ?
Configuration in ECC Integration Engine configuration is as follows
Questions
How the message gets pushed to ECC from PI, once the message received in PI, I believe by G type RFC destination on path "/sap/xi/engine?type=entry" , please clarify.
How to trace this, if message is not getting pushed to ECC, I mean I have checked the trace in PI XSMB_MONI, but didn't get anything for this error. In ECC SXMB_moni only I am able to the timeout error.
Please expert help me as soon as you can, this error really effecting me badly in front of management
Thanks,
Farhan

Hi Hareesh,
I configured the scenario based on ICO, and again I received the same timeout error in ECC.
I am really sick with this error, and I have raised the OSS message to SAP. Meanwhile I just want to double check my entire configuration with you. Please see the below configuration (for classical) for ABAP proxy to HTTP_AAE, and let me know if anything is wrong.
Request structure (ECC->PI->Bank)
<?xml version='1.0' ?>
<PaymentInfoMessage>
<PaymentInfoRequest>
<CompanyCode>Partner01</CompanyCode>
<BankCode>BSFRSARI</BankCode>
<StartDate>2006-07-09T00:00:00</StartDate>
<EndDate>2006-07-09T00:00:00</EndDate>
<TransactionType>940</TransactionType>
</PaymentInfoRequest>
</PaymentInfoMessage>
Response Structure (Bank->PI->ECC)
<?xml version="1.0"?>
<PaymentInfoMessageResponse>
<PaymentInfoResponse>
    <TransactionType>940</TransactionType>
    <SequenceNum>1</SequenceNum>
    <ReceiptTime>2002-01-02T18:01:00</ReceiptTime>
    <ProcessStatus>1</ProcessStatus>
    <Comment>No Comment</Comment>
    <TransactionData>:20:MT940-1007200601
:25:3210000079901
:28C:190/0001
</TransactionData>
    <CompanyCode>PARTNER01</CompanyCode>
</PaymentInfoResponse>
<StatusCode>OK</StatusCode>
<StatusDetail>OK</StatusDetail>
<ResponseItemCount>2</ResponseItemCount>
</PaymentInfoMessageResponse>
ESR Configuration
Please see the below screenshot for ESR config. I have created 4 data types, 4 message types, 2 Service interface (synchronous), 2 mapping and one operation mapping.
I just want to clarify about selecting the Request and response message type in inbound and outbound service interface.
<?xml version='1.0' ?>
<PaymentInfoMessage>
<PaymentInfoRequest>
<CompanyCode>Partner01</CompanyCode>
<BankCode>BSFRSARI</BankCode>
<StartDate>2006-07-09T00:00:00</StartDate>
<EndDate>2006-07-09T00:00:00</EndDate>
<TransactionType>940</TransactionType>
</PaymentInfoRequest>
</PaymentInfoMessage>
Response Structure (Bank->PI->ECC)
<?xml version="1.0"?>
<PaymentInfoMessageResponse>
<PaymentInfoResponse>
    <TransactionType>940</TransactionType>
    <SequenceNum>1</SequenceNum>
    <ReceiptTime>2002-01-02T18:01:00</ReceiptTime>
    <ProcessStatus>1</ProcessStatus>
    <Comment>No Comment</Comment>
    <TransactionData>:20:MT940-1007200601
:25:3210000079901
:28C:190/0001
</TransactionData>
    <CompanyCode>PARTNER01</CompanyCode>
</PaymentInfoResponse>
<StatusCode>OK</StatusCode>
<StatusDetail>OK</StatusDetail>
<ResponseItemCount>2</ResponseItemCount>
</PaymentInfoMessageResponse>
ESR Configuration
I have simply created 2 data types for requests(ECC->PI->Bank) and did one to one mapping. Similarly for response(Bank->PI->ECC) 2 data types, one to one mapping for this as well.
But I just want to clarify about selecting the Request and response message type in inbound and outbound service interface. please explain me this for synchronous interface.
Please see the below structure from ESR and inbound and Outbound service and let me know if the selection of Request and response message types is correct or not.
OutBound service interface
Inbound service interface
Thanks,
Farhan

IMAQdx Timeout Error 0xBFF6901B

Similar Messages

Maybe you are looking for