IMEI not found by network

Just tried to get my 3 iphone 3GS unlocked and they say the phone doesn't exist as the IMEI isn't in their system. What now? I bought it from them 2 years ago and don't have the receipt - the phone does exist as I've been using it and topping it up with them so what can I do now? Don't fancy paying £109 to get a third party to unlock it.

The only official way is through the carrier, in your case AT&T.
All other web unlock services are a hack.

Similar Messages

Photosmart 7515 connect via USB but not wireless, Device not found on Network

Purchased a 7515 all-in-one, was able to setup wirelessly to MacPro but has lost ability to connect wirelessly. This happened with OS X Lion and nor MountainLion. Have a TimeMachine Airport. Printer connects to network but during setup from MacPro, repeatedly get "Device Not Found on Network" after stepping through wireless installation setup screens. I have reset router, printer, firmware updates, software updates.... at wits end. I have followed the instructions on the below resource page link with no luck. Use WPA-PSK encryption (Automatic AES or TKIP) on network and diagnostics on printer pass.
Please help anyone!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02946597&tmp_task=solveCategory&cc=us&dlc=en&la...

It sounds like the Macs and the printer just aren't communicating.
If you press the network icon on the printer, does it indicate it is connected to the network?
I recommend two additional steps that are not listed in the linked document. The printing system of the Mac may need to be reset as it will clear any software that could be interfering (such as corrupted installations).
Follow the steps as outlined for 10.7 or 10.8 in this document from HP.
The next step is to install the driver package from Apple. This can be found here.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

HP 3050A : Device Not Found on Network

Hi,
Laptop Model: MacBook Air
Operation System: OSx Lion 10.7.3
Printer Model: HP 3050A
Router Model: Linksys WAG160N
WiFi Security Protocol: WPA
TCP/IP IPv4 Protocol: DHCP
Firewall Software: None
I have manage to connect the printer to my WiFi network as the blue indicator is ON and got an IP 192.168.1.104 with Excellent signal strength on the printer. But when follow the HP Setup Assistant I unpluged the USB then I got stuck with the following error message:
Device Not Found on Network
The wireless network settings were successfully downloaded to your device. However, your Mac was unable to locate the device on the network.
Please make sure that:
• Your Mac is connected to a wired or wireless network that has access to your device.
• Your device is connected to the wireless network "speedy".
Click "Retry" to attempt to connect again using the current settings. Click "Go Back" to enter different settings.
I also tried to ping the printer IP but no success
Aliss-MacBook-Air:~ ali$ ping 192.168.1.104
PING 192.168.1.104 (192.168.1.104): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
ping: sendto: No route to host
I am able to print using USB without any problem, but the WiFi never success! Please help!
Regards

Hello,
Thanks for the post. With this one, we may a couple of issues. I've included a link below with some excellent information regarding network connectivity. I might suggest that we start there and try to determine if it's the printer, the MAC or the network. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02731071&tmp_task=solveCategory&cc=us&dlc=en&la...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Message 3513 not found; product=NETWORK; facility=TNS

I have installed 11g instant client on windows machine and when I do a tnsping from cmd I get
Message 3513 not found; product=NETWORK; facility=TNS
I have already copied all the files over from mesg folder. Also when I do tnsping on something which is not in tnsnames.ora file I get
C:\Users\xxx>tnsping abc
TNS Ping Utility for 64-bit Window
012 10:49:12
Copyright (c) 1997, 2010, Oracle.
Used parameter files:
D:\oracle\product\11.2.0\client_1\.......
TNS-03505: Failed to resolve name
What else can I do to resolve this?

868806 wrote:
I have installed 11g instant client on windows machine and when I do a tnsping from cmd I get
Message 3513 not found; product=NETWORK; facility=TNS
I have already copied all the files over from mesg folder. Also when I do tnsping on something which is not in tnsnames.ora file I get
Copied from where to where, and why? there should be no reason to be copying these files at all.
C:\Users\xxx>tnsping abc
And to add to the confusion, as has already pointed up, instant client doesn't come with tnsping, so your use of tnsping contradicts your statement that you are working with instant client.
TNS Ping Utility for 64-bit Window
012 10:49:12
Copyright (c) 1997, 2010, Oracle.
Used parameter files:
D:\oracle\product\11.2.0\client_1\.......
TNS-03505: Failed to resolve name
http://edstevensdba.wordpress.com/2011/02/26/ora-12154tns-03505/
What else can I do to resolve this?First, answer the questions to clarify the instant client/tnsping disconnect ...

My macbook pro can not found any network WI-FI

My mac book pro can not found any network in wifi but after turn of and turn on WI-FI for more than 10th it can found network and of course my network
interesting is when i leave my room with my labtop without any trun of or on wifi, network can detect every WI-FI!!!
any ideia ??

Hi alirezaDavid,
If you are having WiFi issues with your MacBook Pro, you may find the following article helpful:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Regards,
- Brenden

My BB Pearl 8100 IMEI # not found

Tried to set up my BB on a plan but my provider said my IMEI number was not found. They are suggesting that my phone has already beeen locked on a plan.
My phone was purchased as "new" and "unlocked". I am beginning to think that it was not unlocked
I purchased the phone on ebay, the seller has been ignoring my messages.
Any suggestions, help anyone. What should I do?
Whats the use having a BB without having to enjoy the full extent of the product?
Thanks!!!

terianrich wrote:
vendor id: 122
122 Telstra, Australia
You should first call them and explain politely that you purchased the device used, and that the former owner did not UNregister the PIN & IMEI from their account, and ask them to release it. They don't have to do so for you, not being the account holder, but they should.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Unlock Page Issues: IMEI not found (errorCode.ULP2003)

Hello ,
I am not an at&t customer and would like to unlock my device. I bought the at&t device off the motorola online store but later realized that the device is locked to at&t. I found this link when I was looking for a solution online. When I try to unlock the device using the device unlock page I get this message saying that the IMEI number I have entered is not a valid one. Following are the details that you requested :-
Cell number - ***
Device Make - Motorola X2 (2014)
Device IMEI - ***
Email address - ***
[Edited for privacy-please do not post personal or unique information such as but not limited to full names, employee ID numbers, email addresses, phone numbers, account numbers, etc.]

Hello!
Cell and/or account number *****
Device Make/Model Samsung S5Active
Device IMEI *****
Email Address *****
I get "unknown IMEI number" when I try to fill out the unlock code request- my account is, I believe, in good standing, the phone is legal (purchased through Costco in December), etc, etc
THANKS!
[Edited for privacy-please do not post personal or unique information such as but not limited to full names, employee ID numbers, email addresses, phone numbers, account numbers, etc.]

"Files not found" and network drive

I'm new to iTunes, and I think there's something fundamental I don't understand about it. I'm hoping someone here can clue me in.
Here's the situation: I have iTunes 7 on a 2.8GHz laptop running WinXP. It's connected via ethernet-based home network to a 400MHz desktop running WinXP. I have a lot of MP3s and M3U playlists created with Winamp on the desktop, which has a much larger hard drive than the laptop -- IOW, I'm not willing to move the MP3s to the laptop, but I want to run iTunes using the laptop's faster CPU (it also has the high-speed USB port my wife's "new" 4G iPod requires).
So what I did was to point the iTunes music folder to the mapped network drive on the desktop and then import all the M3U playlists into iTunes. So far, so good. I can then sync the iPod and all the songs get copied over. However, the next time I reconnect the iPod, all the songs have the "!" symbol next to them, indicating iTunes can't "find" them. When attempting to sync, I get the message that the songs were not copied because they could not be found. I can manually re-point the files to the directory on the mapped drive, but what a pain! The files in the mapped directory are in multiple sub-directories, but iTunes doesn't seem to have trouble searching recursively through sub-directories, so I doubt that's the issue.
I don't see anything in the documentation about problems of this nature with network drives. Is this a "known" issue in the sense that everyone else knows about it except me? If this has been discussed elsewhere on the forum, let me know.
TIA,
Eric
Dell Windows XP Pro

I too find it disturbing that this software is not "home network friendly" I have a similar setup and have digitized 200+ cd's including everything that my kids listen to as well. There are also several wirelessly connected computers in my house, and the last thing I want is a half-dozen copies of every song scattered throughout the house chewing up disk space. So far, I have 3 iPods in our household and my goal is to centrally store music files and allow network access from remote pc's on my network to sync our iPods with music that we own. Windows Vista has this capability with media player 11, and if I were so inclined, I would buy generic mp3 players that are compatible with MS MP sync, but I would like to give Apple a chance to add this feature. If not, the iPods can always be sold on ebay and replaced with MS compatible devices. I don't really want to do this because we do like our iPods.

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (p

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that
the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)(Microsoft SQL Server, Error: 2)
The system cannot find the file specified
Cannot connect to COWBOYS.
Here are the technical details===================================
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider:
Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft%20SQL%20Server&EvtSrc=MSSQLServer&EvtID=2&LinkId=20476
Error Number: 2
Severity: 20
State: 0
Program Location:
at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer
timeout)
at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance)
at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance,
SqlConnectionString userConnectionOptions, SessionData reconnectSessionData)
at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal oldConnection, DbConnectionInternal& connection)
at System.Data.ProviderBase.DbConnectionInternal.TryOpenConnectionInternal(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.SqlClient.SqlConnection.TryOpenInner(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.Open()
at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server)
at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser()
===================================
The system cannot find the file specified
I have tried from so many forms. This is so frustrating. Thank for everyone/anyone who wants to help. So this is what happened: I had to uninstall my previous sqlserver 2012(which worked great) for some reason, and I uninstalled everything from that download.
Then I installed the trial edition of sql server 2012 (64 Bit) and It wouldn't connect to the database. (Error mentioned above.) My local DB is COWBOYS. (COWBOYS is also my computer name.) After this, I have tried downloading sqlexpress and sqlserver 64bit
many times and cannot connect to my local DB.
How do I connect to my Local DB?
Also, I think this might help: (When I run sqlserve.exe, which I was able to find in C:\Program Files\Microsoft SQL Server\110\LocalDB\Binn, I get an error: Your SQL server installation is either corrupt or has been tampered with(Error getting
instance ID from name). Please uninstall then re-run setup to correct this problem.
I would happily re install it, if it wasn't my 20th time.
I don't have any remote connections, I don't use username/password, only window authentication. I work mostly on visual studio, but without able to store /retrieve data, I don't know how to survive.
May be the solution is very simple, but I am too frustrated.
Some of the things I have tried:
From a command prompt, enter one of the following commands:
net start "SQL Server Agent (MSSQLSERVER)" OR
net start "SQL Server Agent(instancename)"(for instance)
on my sql configuration, I cannot start anything because there is nothing there to start. I can post more details, if that would help. Also, some more details about the error:
Details
Product:
SQL Server
ID:
2
Source:
MSSQLServer
Version:
10.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Version:
9.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Any one that can help me, I will be greatful. Thank you so much. p.s. please ask me anything if you have any questions.

It sounds like there are a couple things going on here. First check if you have a successful install of SQL Server, then we'll figure out the connection issues.
Can you launch SQL Server Configuration Manager and check for SQL Server (MSSQLSERVER) if default instance or SQL Server (other name) if you've configured your instance as a named instance. Once you find this, make sure the service is started.
If not started, try to start it and see if it throws an error. If you get an error, post the error message your hitting. If the service starts, you can then launch SSMS and try to connect. If you have a default instance, you can use the machine
name in the connection dialog. Ex: "COWBOYS" where Cowboys is the machine name. However, if you named the SQL Server instance during install, you'll need to connect using the machine\instance format. Ex: COWBOYS\Romo (where Romo
is the instance name you set during install).
You can also look at the summary.txt file in the SQL Server setup error logs to see what happened on the most recent install. Past install history is archived in the log folder if you need to dig those up to help troubleshoot, but the most
recent one may help get to the bottom of it if there is an issue with setup detecting a prior instance that needs to be repaired.
Thanks,
Sam Lester (MSFT)
http://blogs.msdn.com/b/samlester
This posting is provided "AS IS" with no warranties, and confers no rights. Please remember to click
"Mark as Answer" and
"Vote as Helpful" on posts that help you. This can be beneficial to other community members reading the thread.

Error code: 0x80070035 The network path was not found

"Error code: 0x80070035 The network path was not found" while trying to access another PC running Windows 7 Ultimate I searched and read dozens of similiar posts to try to resolve this issue with no success.
The situation is, I have a router in home with 4 PC's connected. My central PC is running Windows 7 Ultimate. The others are Windows 7 Ultimate again, and 2 running XP Pro. No special Firewalls, just have Windows Firewall enabled on all PC's, and am running KasperskyInternetSecurity2010 on all. (Have disabled these on all PC's and tried to view/connect and it didnt make a difference, same error)
Fact one: not attempting a Homegroup connection at all, just simply wishing to connect in a basic network environment where I can drag and drop files between all PC's in my Home Network or in my house , however its considered. But on the Windows 7 I am unable to view either of the XP's only the other Win7, and when I try to access that one is when I get the "Error code: 0x80070035 The network path was not found".
Furthermore, while troubleshooting the problem I opened a Command Prompt in all computers, then an "ipconfig" to view each ip address. Then began to ping each machine to determin connectivity. Which resulted in partial success. My main Win7 machine (which i am on now) was able to ping successfully to all machines. But all other machines were unable to ping to me (main Win7). with a 100% loss.
So at least I determined this is most likely a helpful fact in resolving this. Going into "services.msc" I made sure that all the obvious services are started and running:
DCHP Client, Homegroup Listener, Homegroup Provider, Link-Layer Topology Discovery Mapper, NetTcp Port SHaring Service, Network Connections, Network List Service, Network Location Awareness, TCP/IP NetBIOS Helper
All strarted and running in Automactic mode.
Not sure what other information I can give at this point, to help assist in fixing this problem. Please dont hesitate to ask for me for more info if needed. Ready and willing to try anything to get this working, except for reinstalling the OS. All my programs work great and do not wish to go through the drama ao reinstalling all my programs and activating them and redoing all my Adobe settings and CAD settings.
Someone please help !

Hi,
In addition, I would like to suggest the following:
Enable NetBIOS over TCP/IP:
1.    Go to “Control Panel\Network and Internet\Network Connections”.
2.    Right-Click on the connection and choose Properties.
3.    Click “Internet Protocol (TCP/IP) Version 4” in the list.
4.    Click Properties, and then click Advanced.
5.    On the Advanced TCP/IP settings windows, go to “WINS” tab.
6.    Under NetBIOS setting, click “Enable NetBIOS over TCP/IP”, and then click OK.
Thanks.
Nicholas Li - MSFT

When I try to open up a PDF document, i get the following error message: "There was an error opening this document. The network path was not found" AArrgh please help as I need to open up my documents. Thanks.

When I open up a PDF Document all i get is an error message saying: "There was an error opening this document. The network path was not found" I dont know how to fix this, so looking for some advice please, as I really need o open up my documents.
Thank for any help.

The documents I’m trying to read are already saved on my computer, under various different headings, I know that we have a server, so I only assume these documents are saved on here, as I said before I’m not good with all this techno stuff. I do my work each week ( on a payroll system) and save the documents for each company, they automatically go to the correct place. I never request for them to be saved in a certain place ( well not that I’m aware of) . I then on occasions need to open up this information, it is then that I can’t read or open the documents. We do have a tech help, but they are off sick until the 5th Jan, hence me trying to work out if I can fix this problem through this help site. Its ADOBE Reader that I’m trying to use.

Network card not found after new installation [SOLVED]

I broke my filesystem on my Asus UL80V series laptop in trying to solve problems related to the latest glibc update, so decided to do a clean re-install. I had an installation disk at hand: 2009.08 with kernel 2.6.30.4-1 (which is supposed to have the module for my ath9k network device). However after a successful installation (including all the files from base-dev), my network device is not recognised:
dhcpcd: eth0: interface not found or invalid
although network connectivity (wired and wireless) worked perfectly before the installation attempt.
This happened yesterday (17th) and I have been scouring the web since trying to find out what the cause of this problem is, without luck.
I also burned a new installation CD with the latest stable version, but no luck there, either! Got a message at the beginning informing me that the install requires 64 Mb memory, although my laptop has 4 Gb.
I should say, the device is there and working:
lspci | grep Net
gives
02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
I also did
modprobe ath9k
just to make sure. No luck.
Any help will be appreciated.
thanks
thea
Last edited by thea (2012-07-23 23:59:16)

Argh, ip may not be around in the 2009 image really ;-) .. Use "ifconfig" instead..
But: I meanwhile cross-checked your ath9k: http://wireless.kernel.org/en/users/Dri … h9k_driver
and it does not sound encouraging for the kernel you have there.
The image is far too old anyway, if you ask me (would be a darn hazzle to get that uptodate I am sure). Pity you get that memory error with the 2011 one. Maybe check forums on that. Sounds very strange, I am not aware of any post I read.
If you can burn another CD, you can try the recent ISOs as well: http://releng.archlinux.org/isos/
Beware that the ones from July dont have the AIF setup anymore.

Updating hybrid configuration failed - Kerberos authentication: The network path was not found

I'm configuring Exchange 2010 SP3 as a Hybrid server with Exchange Online. This is a single server running Exchange roles Mailbox, Client Access, Unified Messaging and Hub Transport.
When I run the Manage Hybrid Configuration, I receive the following error:
Updating hybrid configuration failed with error
'System.Management.Automation.Remoting.PSRemotingTransportException: Connecting to remote server failed with the following error message : WinRM cannot process the request. The following error occurred while using Kerberos authentication: The network
path was not found.
The full text from the Hybrid Configuration log file (C:\Program Files\Microsoft\Exchange Server\V14\Logging\Update-HybridConfiguration)
[1/5/2014 21:21:1] INFO:Opening runspace to
http://[servername]/powershell?serializationLevel=Full
[1/5/2014 21:21:1] INFO:Disconnected from On-Premises session
[1/5/2014 21:21:1] ERROR:Updating hybrid configuration failed with error 'System.Management.Automation.Remoting.PSRemotingTransportException: Connecting to remote server failed with the following error message : WinRM cannot process the request. The following
error occured while using Kerberos authentication: The network path was not found.
Possible causes are:
-The user name or password specified are invalid.
-Kerberos is used when no authentication method and no user name are specified.
-Kerberos accepts domain user names, but not local user names.
-The Service Principal Name (SPN) for the remote computer name and port does not exist.
-The client and remote computers are in different domains and there is no trust between the two domains.
After checking for the above issues, try the following:
-Check the Event Viewer for events related to authentication.
-Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
Note that computers in the TrustedHosts list might not be authenticated.
   -For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic.
   at System.Management.Automation.Runspaces.AsyncResult.EndInvoke()
   at System.Management.Automation.Runspaces.Internal.RunspacePoolInternal.EndOpen(IAsyncResult asyncResult)
   at System.Management.Automation.Runspaces.RunspacePool.Open()
   at System.Management.Automation.RemoteRunspace.Open()
   at Microsoft.Exchange.Management.Hybrid.RemotePowershellSession.Connect(PSCredential credentials, CultureInfo sessionUiCulture)
   at Microsoft.Exchange.Management.Hybrid.Engine.Execute(ILogger logger, String onPremPowershellHost, PSCredential onPremCredentials, PSCredential tenantCredentials, HybridConfiguration hybridConfiguration)
   at Microsoft.Exchange.Management.SystemConfigurationTasks.UpdateHybridConfiguration.InternalProcessRecord()'.
I have sought help, posting on the forum at community.office365.com -
http://community.office365.com/en-us/forums/158/t/212265.aspx. But I've got to a point where I believe the problem is more to do with how PowerShell is operating on the on-prem Exchange server.
Has anyone else come across this problem running the Hybrid Configuration Wizard?

Hello Darrell,
Have you verified the settings of Powershell virtual directories for the on-premises Exchange Servers? The following article has a list of some common issues with that virtual directory and how to correct them:
http://technet.microsoft.com/en-us/library/ff607221(v=exchg.80).aspxI would take a look at the one titled "Configure Kerberos Authentication" specifically to ensure everything
looks good.
As the article states you can run the Exchange BPA and it will check if any of these exist as well.

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible.

Server Error in '/' Application.
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Data.SqlClient.SqlException: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SqlException (0x80131904): A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)]
System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) +4846887
System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) +194
System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) +4860189
System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) +90
System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) +342
System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) +221
System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) +189
System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) +185
System.Data.ProviderBase.DbConnectionFactory.CreatePooledConnection(DbConnection owningConnection, DbConnectionPool pool, DbConnectionOptions options) +31
System.Data.ProviderBase.DbConnectionPool.CreateObject(DbConnection owningObject) +433
System.Data.ProviderBase.DbConnectionPool.UserCreateRequest(DbConnection owningObject) +66
System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject) +499
System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) +65
System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) +117
System.Data.SqlClient.SqlConnection.Open() +122
System.Data.Common.DbDataAdapter.QuietOpen(IDbConnection connection, ConnectionState& originalState) +31
System.Data.Common.DbDataAdapter.FillInternal(DataSet dataset, DataTable[] datatables, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) +112
System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) +287
System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, String srcTable) +92
System.Web.UI.WebControls.SqlDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments) +1297
System.Web.UI.DataSourceView.Select(DataSourceSelectArguments arguments, DataSourceViewSelectCallback callback) +19
System.Web.UI.WebControls.DataBoundControl.PerformSelect() +142
System.Web.UI.WebControls.BaseDataBoundControl.DataBind() +73
System.Web.UI.WebControls.GridView.DataBind() +4
System.Web.UI.WebControls.BaseDataBoundControl.EnsureDataBound() +82
System.Web.UI.WebControls.CompositeDataBoundControl.CreateChildControls() +72
System.Web.UI.Control.EnsureChildControls() +87
System.Web.UI.Control.PreRenderRecursiveInternal() +44
System.Web.UI.Control.PreRenderRecursiveInternal() +171
System.Web.UI.Control.PreRenderRecursiveInternal() +171
System.Web.UI.Control.PreRenderRecursiveInternal() +171
System.Web.UI.Control.PreRenderRecursiveInternal() +171
System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +842
Version Information: Microsoft .NET Framework Version:2.0.50727.3082; ASP.NET Version:2.0.50727.3082

On what website/link did you received this error message ??

SCOM agent install fails Error 80070035 - the network path was not found

I have deployed SCOM 2012 agents to most servers (2008, 2008 R2, 2012, 2012R2) in our estate but some either fail to install or are not monitored. I assume the two problems are related, but for now I am concentrating on the servers that fail completely.
Installation is from the Discovery Wizard and I have about 20 servers that fail of various server versions.
So looking at one specific server that is failing to install the agent - a 2008 standard service pack 2
The firewall in on and file and printer sharing is enabled for domain, remote administration is enabled for domain
I added a specific rule to allow TCP 5723 and 5724
DCOM is enabled
I can Ping the target server from the SCOM server by both name and FQDN - both return the same IP and our DNS server has only one entry for this server
I can browse to the admin share \\server\C$ from the SCOM Server, using the same account that I specify for the agent install that is a domain admin with rights on this server (and on the other servers the agent
did install to) and the server has plenty of disk space available
I am not sure what else to look at so would welcome any ideas
Thanks

Hi Petro,
I have a Agent installation failure cheat sheet, For your error 80070035 it is said to perform a manual installation.
So i would like to understand which version of SCOM is this ? 2007 R2 or 2012 or 2012 r2 ?
Also check if your agents have the WMI service started and enabled ?
Also if yours is a SCOM 2007 R2 do you have a RMS & MS in your management group ? If yes then Pushing the agent installation from MS may cause such issue. So would suggest you push the installation from RMS.
Also check if your Network connectivity meets the minimum requirement as recommended by SCOM. Below is applicable for Both SCOM 2007 R2 & SCOM 2012 & 2012 R2.
Component A
Component B
Minimum Requirement
Root management server or management server
Agent
64 Kbps
Root management server or management server
Agentless
1024 Kbps
Root management server or management server
Database
256 Kbps
Also check if you have any Anti virus / Firewall which is blocking the install / communication. If yes disabe or add the "Monitoringhost.exe to the safe list or what your feature is.
Check if you have another IP assigned to the NIC card and remove it tempraurly andchecl.
Also post the event logs of the Agents which are in not monitored state for analysis.
SCOM Agent installation failure error codes
Error
Error Code(s)
Remediation Steps
The MOM Server could not execute WMI Query "Select * from Win32_Environment where
NAME='PROCESSOR_ARCHITECTURE'" on computer server.domain.com
Operation: Agent Install
Install account: domain\account
Error Code: 80004005
Error Description: Unspecified error
80004005
1. Check the PATH environment variable. If the PATH statement is very long, due to lots of installed third party software - this can
fail. Reduce the path by converting any long filename destinations to 8.3, and remove any path statements that are not necessary.
2. The cause
could be corrupted Performance Counters on the target Agent.
To rebuild all Performance counters including extensible and third party counters in Windows Server 2003, type the following commands at a command
prompt. Press ENTER after each command.
cd
\windows\system32
lodctr /R
Note /R is uppercase.
Windows Server 2003 rebuilds all the counters because it reads all the .ini files in the C:\Windows\inf\009 folder for the English operating system.
How to manually rebuild Performance Counter Library values
http://support.microsoft.com/kb/300956
3. Manual agent install.
The MOM Server could not execute WMI Query "Select * from Win32_OperatingSystem" on
computer “servername.domain.com”
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 800706BA
Error Description: The RPC server is unavailable.
8004100A
800706BA
1. Ensure agent push account has local admin rights
2. Firewall is blocking NetBIOS access
3. Inspect WMI health and rebuild repository if necessary
4. Firewall is blocking ICMP (Live OneCare)
5. DNS incorrect
The MOM Server failed to open service control manager on computer "servername.domain.com". Access is Denied
Operation: Agent Install
Install account: DomainName\User Account
Error Code: 80070005
Error Description: Access is denied.
80070005
80041002
1. Verify SCOM agent push account is in Local Administrators group on target computer.
2. On Domain controllers will have to work with AD team to install agent manually if agent push account is not a domain admin.
Disable McAfee antivirus during push
The MOM Server failed to open service control manager on computer "servername.domain.com".
Therefore, the MOM Server cannot complete configuration of agent on the computer.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 800706BA
Error Description: The RPC server is unavailable.
800706BA
1. Firewall blocking NetBIOS ports
2. DNS resolution issue. Make sure the agent can ping the MS by NetBIOS and FQDN. Make sure the MS can ping the agent by NetBIOS
and FQDN
3. Firewall blocking ICMP
4. RPC services stopped.
The MOM Server failed to acquire lock to remote computer servername.domain.com. This means there is already an agent management operation proceeding
on this computer, please retry the Push Agent operation after some time.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 80072971
Error description: Unknown error 0x80072971
80072971
This problem occurs if the LockFileTime.txt file is located in the following folder on the remote computer:
%windir%\422C3AB1-32E0-4411-BF66-A84FEEFCC8E2
When you install or remove a management agent, the Operations Manager 2007 management server copies temporary files to the remote computer. One
of these files is named LockFileTime.txt. This lock file is intended to prevent another management server from performing a management agent installation at the same time as the current installation. If the management agent installation is unsuccessful and
if the management server loses connectivity with the remote computer, the temporary files may not be removed. Therefore, the LockFileTime.txt may remain in the folder on the remote computer. When the management server next tries to perform an agent installation,
the management server detects the lock file. Therefore, the management agent installation is unsuccessful.
http://support.microsoft.com/kb/934760/en-us
The MOM Server detected that the following services on computer "(null);NetLogon" are not running. These services are required for push
agent installation. To complete this operation, either start the required services on the computer or install the MOM agent manually by using MOMAgent.msi located on the product CD.
Operation: Agent Install
Remote Computer Name: servername.domain.com Install account: DOMAIN\account
Error Code: C000296E
Error Description: Unknown error 0xC000296E
C000296E
1. Netlogon service is not running. It must be set to auto/started
The MOM Server detected that the following services on computer
"winmgmt;(null)" are not running
C000296E
1. WMI services not running or WMI corrupt
The MOM Server detected that the Windows Installer service (MSIServer) is disabled on computer "servername.domain.com". This service is
required for push agent installation. To complete this operation on the computer, either set the MSIServer startup type to "Manual" or "Automatic", or install the MOM agent manually by using MOMAgent.msi located on the product CD.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: C0002976
Error Description: Unknown error 0xC0002976
C0002976
1. Windows Installer service is not running or set to disabled – set this to manual or auto and start it.
The Agent Management Operation Agent Install failed for remote computer servername.domain.com.
Install account: DOMAIN\account
Error Code: 80070643
Error Description: Fatal error during installation.
Microsoft Installer Error Description:
For more information, see Windows Installer log file "C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameAgentInstall.LOG
C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameMOMAgentMgmt.log" on the Management Server.
80070643
1. Enable the automatic Updates service…. Install the agent – then disable the auto-updates service if desired.
Call was canceled by the message filter
80010002
Install latest SP and retry. One server that failed did not have Service pack installed
The MOM Server could not find directory \\I.P.\C$\WINDOWS\. Agent will not be installed on computer "name". Please verify the required
share exists.
80070006
1. Manual agent install
Possible locking on registry?
http://www.sysadmintales.com/category/operations-manager/
Try manual install.
Verified share does not exist.
The network path was not found.
80070035
1. Manual agent install
The Agent Management Operation Agent Install failed for remote computer "name". There is not enough space on the disk.
80070070
1. Free space on install disk
The MOM Server failed to perform specified operation on computer "name". The semaphore timeout period has expired.
80070079
NSlookup failed on server. Possible DNS resolution issue.
Try adding dnsname to dnssuffix search list.
The MOM Server could not start the MOMAgentInstaller service on computer "name" in the time.
8007041D
80070102
NSlookup failed on server. Possible DNS resolution issue.
Verify domain is in suffix search list on management servers.
The Agent Management Operation Agent Install failed for remote computer "name"
80070643
1. Ensure automatic updates service is started
2. Rebuild WMI repository
3. DNS resolution issue
The Agent Management Operation Agent Install failed for remote computer "name". Another installation is already in progress.
80070652
Verify not in pending management. If yes, remove and then attempt installation again.
The MOM Server detected that computer "name" has an unsupported operating system or service pack version
80072977
Install latest SP and verify you are installing to Windows system.
Not discovered
Agent machine is not a member of domain
Ping fails
1. Server is down
2. Server is blocked by firewall
3. DNS resolving to wrong IP.
Fail to resolve machine
1. DNS issue
The MOM Server failed to perform specified operation on computer "name". Not enough server storage…
8007046A
1. This is typically a memory error caused by the remote OS that the agent is being installed on.
There are currently no logon servers available to service the logon request.
8007051F
1. Possible DNS issue
This installation package cannot be installed by the Windows Installer service. You must install a Windows service pack that contains a newer version
of the Windows Installer service.
8007064D
1. Install Windows Installer 3.1
The network address is invalid
800706AB
Possible DNS name resolution issue.
Tried nslookup on server name and did not get response.
Verify domain is in suffix search list on management servers.
The MOM Server failed to perform specified operation on computer servername.domain.com
80070040
1. Ensure agent push account has local admin rights
The MOM Server detected that the actual NetBIOS name SERVERNAME is not same as the given NetBIOS name provide for remote computer SERVERNAME.domain.com.
80072979
1. Correct DNS/WINS issue.
2. Try pushing to NetBIOS name
Gautam.75801

IMEI not found by network

Similar Messages

Maybe you are looking for