Impact of Config. Change on Positive / Negative list

Hi,
I have a scenario where many of the partners are either positive or Negative listed. Now If I make a change in config for the legal regulation SPLUS, then during the next screening against the updated SPL list will these positive and negative list be re screened ??

Hi Murali,
The positive and negative lists will need to be rescreened via the following tcodes
Positive List : /SAPSLL/SPL_CHSB1PLO
Negative List : /SAPSLL/SPL_CHSB1NLO
The config change in GTS would not trigger an automatic rescreening request .
Let me know if this helps.
Thanks
Jasmit Kohli

Similar Messages

How can we change the position of an employe in 0001

Dear Friends,
I would like to change a record (either by copy/change) for infotype 0001 in order to change the position of any employee. Through PA30 when iam trying to do a copy
i found that the position field is only non-editable mode . Could any one let me know what is the procedure if you want to change the position of the employee.
regards
syamla

Hi syamla,
To cahnge position proceed in the following way:
Go to Pa30, select personnel number for whom u want to change position, select infotype 1 and click on "overview" icon.
In the "List actions" screen u will find one or many actions. Now select one action (where u want to change position) and click on "Copy" icon. Now u will reach "copy actions screen", and postion is field is editable. Change position. U might get this entry deletes a record, press enter. Save ur entries and continue to org. assignment infotype. save org. assignment infotype also.
Hope this will help u.
Reward points if helpful
Rajesh Panda

Need help for finding objects impacted by size change for an infoobject

hi all,
need help for finding objects impacted by size change
for xxx infoobject, due to some requirements, the size to be changed from
char(4) to char(10), in the source database tables as well as adjustment
to be done in BI side.
this infoobject xxx is nav attribute of YYY as well as for WWW
infoobjects. and xxx is loaded from infopkg for www infoobject load.
now that i have to prepare an impact analysis doc for BI side.
pls help me with what all could be impacted and what to be done as a
solution to implement the size change.
FYI:
where used list for xxx infoobject - relveals these object types :
infocubes,
infosources,
tranfer rules,
DSO.
attribute of characteristic,
nav attribute,
ref infoobject,
in queries,
in variables

Hi Swetha,
You will have to manually make the table adjustments in all the systems using SE14 trans since the changes done using SE14 cannot be collected in any TR.
How to adjust tables :
Enter the table name in SE14. For ex for any Z master data(Say ZABCD), master data table name would be /BIC/PZABCD, text table would be /BIC/TZABCD. Similarly any DSO(say ZXYZ) table name would be /BIC/AZXYZ00 etc.
Just enter the table name in SE14 trans --> Edit --> Select the radio button "Save Data" --> Click on Activate & adjust database table.
NOTE : Be very careful in using SE14 trans since there is possibility that the backend table could be deleted.
How to collect the changes in TR:
You can collect only the changes made to the IO --> When you activate, it will ask you for the TR --> Enter the correct package name & create a new TR. If it doesn't prompt you for TR, just goto Extras --> Write transport request from the IO properties Menu screen. Once these IO changes are moved successfully, then the above proceduce can be followed using SE14 trans.
Hope it helps!
Regards,
Pavan

ACS will not save the config changes to reports

I have configured a very old ACS appliance, 4.1. At this time this is what I we have to use. The authentication is working fine, the reports for accounting, TACACS+ accounting is only saving the login and logout of the users and not any config changes that are being made.
I'm hoping that someone may have an idea of what accounting command I am using or if this older version has some changes that need to be done as the config/aaa lines I use today and work on newer version work. I was under the impression that this line "aaa accounting exec default start-stop group tacacs+" would send every command to the tacacs server?
aaa new-model
aaa authentication login default group tacacs+
aaa authorization config-commands
aaa authorization exec default group tacacs+ none
aaa authorization commands 0 default group tacacs+ none
aaa authorization commands 1 default group tacacs+ none
aaa authorization commands 2 default group tacacs+ none
aaa authorization commands 7 default group tacacs+ none
aaa authorization commands 15 default group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
any ideas would be3 appreciated. thanks for reading
Yvon

Hi martijn,
Are there some custom fields in this list or some duplicate columns? Please have a check.
For more information about the possible reasons and solutions, see
http://social.technet.microsoft.com/Forums/en-US/sharepointcustomizationprevious/thread/ae946f73-3126-41ad-833b-25e4cc2b7723#e22af3fe-8203-45c4-8d19-e18041a048e2
http://social.technet.microsoft.com/Forums/en-US/sharepointgenerallegacy/thread/59895a6b-7f61-431f-a762-e3fd9d81fe34
http://social.technet.microsoft.com/Forums/en/sharepointcustomizationprevious/thread/eba4cd7e-498a-465f-adea-decae44d7a8c
Regards,
Kelly Chen

Change variable from negative to postive

hallow
i wont top now how i change variable from negative to postive
like change -5 to 5
thankes

Hi Shnya,
You just multiply with " -1", it wil get converted from Positive to negative or vice versa.
Hope I answered your query.
Regards,
Sujatha

How to add config changes in Transport Request

Hi Experts,
We did some config changes in Logistics - General=>Material Master=>Configuring the Material Master=>Define structure of Data screen for screen sequence / Assign Secondary sequence / Maintain Order of Main and Additional Screens.
But while saving this config of Assign Secondary sequence / Maintain Order of Main and Additional Screens its not asking for Transport Request.
Even i checked in the menu of EDIT-Tranport entries, but the menu's are in disable mode.
Can anyone guide me how to add this two fields config changes in to TR?
Thanks and regards,
Anandhan

Hi,
This is really strage.
However you can try the following.
upon entering the config node, use the first menu option in which option "transport" would be there.
Upon clicking it, the same table opens in display mode.
Select the entries that you have created and use the option "include in transport"
When asked for, provide teh transport number.
Alternatively you can create a transport and them use SE10 to include entries from tables that you can select.
ou may need teh help of an experinced ABAPer or Basis to do it if you are not confortable doing it yourself.
However if the config effects multiple tables, then this is not a viable option as you need to know all the impacted tables.
hope this helps.

How do you change the position of email sender so that it's on the left (sender[from], subject and date received)

How do you change the position of email sender so that it's on the left (sender[from], subject and date received)

In the Thread Pane where your messages are listed?
You see that bar with the labels "From", "Subject", "Date" and so on? Well, they are buttons. You can click on them to sort your messages. You can also drag them with the mouse left and right to reposition them, and you can drag their ends to change the column widths.
These are standard computer actions; you can do all of this in Windows Explorer ("My Computer") too.
In Thunderbird, a right-click on any of these buttons will reveal a pop-up menu where you can select and deselect the columns to control what is shown.
More here: http://www.ramsden.org.uk/8_How_to_sort.html

How to edit the negative list

Where in GTS can I add to or remove an entity from the ngative list?

Hi Daniel,
Choose the BP you would like to add to the negative list and screen it using transaction /SAPSLL/SPL_CHSB1LO.
Then from the next screen hit the "Negative List" button:
To remove from the negative list go to transaction BP enter the business partner number and navigate to the SAP GTS tab.
Go to change mode and change the value highlighted from "2" to "SPACE" and save.
Best Regards,
Eoin

Change the position of subform in adobe forms

Hi,
I have a requirement to change the position of subform(y co-ordinate) in offline adobe forms.
My subform is positioned and my code is:
this.y = "10 in".
Though this question has been answered a few times,I could not find the answer in any of them.
Please suggest...
Thanks and regards,
Raka.

Presenter doesn't have the same functionality for the TOC as Captivate. There is some wizardry that can be done if you want to adjust the look of the slide list.
Work around was discussed in this thread: http://forums.adobe.com/message/1970468#1970468

How to Change the position of Roles

Dear Experts,
I have a requirement in which I have to change the position of the roles.
How to achieve it, Please Suggest.
Warm Regards,
Upendra Agrawal

HI Upendra,
Follow the below process to re-arrange the roles as per your requirement:
1. From the Portal Catalog, right-click a role or workset and choose Open ® Object. The role or workset is loaded into the appropriate editor.
       2.      In the displayed editor, select either:
   The root node of the role or workset hierarchy
A workset or folder within the role or workset hierarchy
A folder within a workset of the role or workset hierarchy
       3.      In the Role/Workset Editor, click Properties to display in the Property Editor the properties of the object that you selected.
       4.      From the Property Category dropdown list, choose Navigation.
       5.      In the property list, scroll to the Sort Priority property and enter a numeric value.
       6.      Click Save.
In the same way, assign values to all of the navigation nodes that you want at specific locations in the portal navigation hierarchy.
Hope it helps.
Regards,
Gourav.

SIP stops when upgrading from ASA from 8.4.1 to 8.4(2)8 w/ out config change? Why?

I have to be missiong something small in my config.
If I upgrade my ASA 5510 which I am routing and NATing off of, from 8.4.1 to 8.4.2.8, SIP stops. All phones go dead.
If I roll bck to 8.4.1, SIP comes up.,... Go bck to 8.4(2)8 nd SIP goes down.....
This is without mking any config changes.
I have looked at it so long, I must be overlooking something simple, simple, simple...

Have spent sIx hours in past 24 w/ Cisco TAC and they have a tin of caps as have I but can't figure out why there is a denial of SIP from inside outside and outside inside to/from sip providers three IP addresses. Have created new access lists, new access groups to allow all 3 ip's in & out, increased timeout, bypassed IPS, have both sip UDP & tcp allowed in/out, specified inspection to approve any any for all sip protocols in/out to/from Lync & mediation and nada.
To answer another question, yes I'm certain config doesn't change... I reloaded tge same running config from a bkup just to make sure.....
What I see in the logs coming in/out is the call does make it all the way through the SSM to the ASA..
What happens there is the head scratcher...
SiP even though allowed and even though I've specified it to push through inspection On ASA side is denied based on inspection rule...
I also tried using another one of my (unused) public IPs for only SIP thinking that maulybe there was a core conflict with multiple services NATd to the same public IP but that also did nothing.
On topology I only have a single location so I'm using my 5510 to route as well...
Have 1 IIS web server l, SQL, (ports clised except to obe vendor and am allowing via access list by their IP and ipsec,) Exchange, Lync, Ironport, Endpoint and everything else is 80/80...
Everything is on Server 08r2 w/ exception of web server and two boxes ( one stand-alone & one VM on hyper-v) I am running Server8 for Microsoft TAP engineering / validation airlift. Neither of those are attached to UC/UM at all...
I'm using dynect from dyndns for outside network web services and just piggybacking on time Warner metro e for internal (no physical DNS server)
When I look at caps everything is identical in the tcp and UDP trace even on sip except for the denial...
Which caps/logs would 'y'all like to see and I'll post em when I get home....
Is there a link to bug notes Jullio? Is it sip specific? Any possibility of it being just a name/cosmetic big I can force a work around to?
I recall when Asa first was released I had to specify port 25 allow instead of being able to simply say allow smtp .. That took 2 weeks but it allowed for a work around so whatever I can do/try I'm willing!! Someone may wanna tell TAC if it's a bug because after 6 hours yesterday they are saying there's not a bug... :)
Thanks all!!!!

Changing the Position of iview in Detailed Navigation

Hi,
I want to change the position of the iview in detailled navigation, Ex i have 4 iviews in detailed navigation as
1
2
3
4
now i want to bring 4 up, in the sense between 2 & 3.
One option is by setting the Sort Priority and i'am trying with other option on role level. I'am editing the role which has this 4 iviews assigned, right click on iview 4 and using option Move-->Up. Does this method work, please let me know.
Regards,
Pradeep

Hi Pradeep,
You can try below options -
1) Go to content Administration. Locate your Default Framework Page assigned to your Desktop .Double click it, a new window opens on right side. Out of various iviews, Check Desktop Innerpage and select Open tab. It will display 6 iviews. From the Page Content List of the Desktop Innerpage, select the Detailed Navigation iView (com.sap.portal.detailedNavigationTree) and click Properties. In the displayed Property Editor, check, set, and change the properties of the Detailed Navigation iView, as necessary.
2) You'll get a bak file for detailed navigation area.The par file is com.sap.portal.navigation.detailedtree.par.bak. You can get this par file from server System Admin>>Support>>Portal Runtime>>Browse deployment>>WEB-INF>>Deployment>>pcd. Import this par file into ur NWDS and edit it accordingly.
Regards,
Sen

SNMPv3 config changing after reboot

Whenever one of my C2960's reboot, our Solarwinds monitoring stops working. I found that this is due to one line of SNMPv3 config changing by itself. This used to be in the config:
     snmp-server group XXX v3 priv access permit-snmp
(permit-snmp being the access-list defining ip addresses allowed to query) After the reboot, snmpv3 stops working and this line shows up in the config instead of the one above:
     snmp-server group XXX v3 priv notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF7F
Is this a bug? (I did check the bug database, without success.) I have upgraded the IOS to 12.2(53) SE2 without any success. The switch is a C2960-24TC-L.

I had the same problem and believe the issue is that you probably have a trap server configured and are using the same snmp-server group for the trap server and your queries. I created another group for SNMPv3 queries and the configuration no longer seems to get overwritten. Here's what I did.
Go into config mode and create a group just for the trap server - let's call it TRAPS. I used priv and it looks like that's what you use. Don't worry about defining any MIB views as this group will automatically populate the notifyview once the trap servers below are added to the config. (...and will remove the readview and writeview entries after reboot - that's why a second group is needed). Remove your old trap server entries and set up the new trap server using the new group called TRAPS.
snmp-server group TRAPS v3 priv
snmp-server host version 3 priv TRAPS
Now create another group for queries only - (let's call it QUERIES but you could just use your current group XXX since it's already set up) - I like the v1default MIB view for both reads and writes but you can limit the MIBs with the snmp-server view command. I am using md5 and des56 here - your case may be different - and set up the user (or keep the one you already have configured)
snmp-server group QUERIES v3 priv read v1default write v1default access
snmp-server user QUERIES v3 auth md5 priv des56
Exit and check the config.
The group TRAPS should have the notifyview set. The group QUERIES should have the readview and writeview set to v1default (or whatever view you chose to enter here). The two SNMPv3 groups should look like this:
#sh snmp group
groupname: TRAPS                            security model:v3 priv
readview :           writeview:
notifyview: *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.F
row status: active
groupname: QUERIES                          security model:v3 priv
readview : v1default                        writeview: v1default
notifyview:
row status: active      access-list: 4
The old trap server entry using the old group XXX should have been removed already. Verify that the user: entry says TRAPS
#sh snmp host
Notification host: xxx.xxx.xxx.xxx      udp-port: 162   type: trap
user: TRAPS     security model: v3 priv
Finally make sure the user is in the correct group (QUERIES):
#sh snmp user
User name:
Engine ID: xxxxxxxxxxxxxxxxxxxxxxxxxx
storage-type: nonvolatile        active
Authentication Protocol: MD5
Privacy Protocol: DES
Group-name: QUERIES
If all is well - write the config. You should now be able to perform a coldstart without losing your SNMPv3 config.
Please, let me know if this worked for you.

How to Change the position of Column in ALV report

Hi Follks,
    Is is possible to change the position of column in ALV report?.If yes then how?
    Basically my requirement is, that user want afacility where , he should be able to change the position
    of column aftre he runs the report.
    Eg: After running the report , user felt that column 5 should be at position 2 , in that case he should
           be able to drag column 5 at position 2 and vice versa.
    Please help me, how to solve this issue.
    Note : I am using NW 7.0 SP 9
    Regards
    PG
Edited by: PG on Apr 13, 2009 11:10 AM

HI PG,
do below whie filling the filed catlog
wa_fieldcat-fieldname        = 'Field1".
wa_fieldcat-COL_POS = '1',
append wa_fieldcat to it_fieldcat.
wa_fieldcat-fieldname         = 'Field2".
wa_fieldcat-COL_POS = '2',
wa_fieldcat-fieldname         = 'Field3".
wa_fieldcat-COL_POS = '3',
Thanks!

Is it possible to change the position of beining of text in a standard report

Hi,
I am wondering wether it is possible to change the position of the test (the starting point) in a standard report. I would like to print a label with different texts at different positions. If its not possible in a standard report is there any other way to do it.
Thank you,
Mudda.

Hi Mudda, I don't see any way myself to set any particular starting position for your text. It looks like the best way to emulate this behavior would be to add a new line with lots of tab characters or spaces to place your new text at a specific offset from the left. You can also use Append Table to Report and wire in a 2D string array with only a few positions filled in with your various text labels as shown below. This will space text labels pretty well across the page. Try it out and see if it works for you. You could be more clever and build the 2D array programmatically if you wanted more control over position.
Message Edited by Jarrod S. on 06-02-2006 05:37 PM
Jarrod S.
National Instruments
Attachments:
Set_Report_Position.JPG ‏69 KB

Impact of Config. Change on Positive / Negative list

Similar Messages

Maybe you are looking for