Impact of having no switch profile on N5k
Just curious, I am not real enthusiastic with switch profiles and config sync. I want to remove the switch profile which I have tested in a lab situation and found doing so is not a major issue. What I am interested in, has anybody done this and what kind of issues have cropped up after doing so, besides the obvious of having to ensure accuracy between the two N5k's particularly when it comes to the Fex's. Just curious what other people have experienced. Thanks for any info.
Hi,
The Calendar Repair Assistant is used to detect and correct inconsistencies with single and recurring meeting items for mailboxes located on the Mailbox server. Then recipients won't miss meeting announcements or have unreliable meeting information. Based
on my knowledge, there is no official article mentioning that enabling Calendar Repair Assistant has an impact on performance.
Hope my clarification can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support
Similar Messages
-
Switch profile peers not reachable
Hello:
I have a couple of N5k 5.2(1)N1(1). I'm trying to create a switch profile for all vPC configuration. They are connected to a OOB network through their mgmt0 interface, and ping is succesful. However, the show switch-profile status command shows they can reach eachother.
CONFIG SWITCH 1
feature telnet
feature tacacs+
cfs ipv4 distribute
cfs eth distribute
feature interface-vlan
feature lacp
feature vpc
feature lldp
feature vtp
feature fex
interface mgmt0
vrf member management
ip address 10.161.20.88/24
switch-profile XXX
sync-peers destination 10.161.20.87
SWITCH 1# sh cfs status
Distribution : Enabled
Distribution over IP : Enabled - mode IPv4
IPv4 multicast address : 239.255.70.83
IPv6 multicast address : ff15::efff:4653
Distribution over Ethernet : Enabled
SWITCH 1# sh switch-profile status
switch-profile : XXX
Profile-Revision: 1
Session-type: Initial-Exchange
Session-subtype: Init-Exchange-All
Peer-triggered: No
Profile-status: -
Local information:
Status: Verify Failure
Error(s): Peer not reachable over CFS
Peer information:
IP-address: 10.161.20.87
Sync-status: Not yet merged
Merge Flags: pending_merge:1 rcv_merge:0 pending_validate:0
Status: -
Error(s):
CONFIG SWICTH 2
feature telnet
feature tacacs+
cfs ipv4 distribute
cfs eth distribute
feature interface-vlan
feature lacp
feature vpc
feature lldp
feature vtp
feature fex
interface mgmt0
vrf member management
ip address 10.161.20.87/24
switch-profile XXX
sync-peers destination 10.161.20.88
SWITCH 2# SH CFS STATUs
Distribution : Enabled
Distribution over IP : Enabled - mode IPv4
IPv4 multicast address : 239.255.70.83
IPv6 multicast address : ff15::efff:4653
Distribution over Ethernet : Enabled
SWITCH 2# SH SWItch-PROfile STATUs
switch-profile : XXX
Start-time: 371925 usecs after Thu Jan 17 06:37:58 2013
End-time: 107348 usecs after Thu Jan 17 06:39:58 2013
Profile-Revision: 1
Session-type: Initial-Exchange
Session-subtype: Init-Exchange-All
Peer-triggered: No
Profile-status: -
Local information:
Status: Verify Failure
Error(s): Peer not reachable over CFS
Peer information:
IP-address: 10.161.20.88
Sync-status: Not yet merged
Merge Flags: pending_merge:1 rcv_merge:0 pending_validate:0
Status: -
Error(s):
What can I be missing here?Hi Robert:
Sadly, not even the TAC could solve this. We ended up not using vPC, which is a pity.
Best regards, Faimy. -
I have recently transferred data from my old Mac to my new one. The result was good, but I have 2 users now, whose data I want to merge into 1 single user, so to avoid having to switch from one user to the other to view and use certain files. How to do it?
Here's an easy way:
Pick the user that you want to eliminate (making sure that the remaining user has administrator privileges) and move all of the data that you want to keep into the Shared folder. Reboot or log out and login to the user you want to keep. Copy all the data from the Shared folder into your account - placing it neatly in folders (Documents, Music, Movies, etc.).
Once the data is moved, log into the account you want to delete just once more to make certain that you've grabbed all the data you want to keep. Log out and log back into your admin account and go to System Preferences>Users & Groups and delete the 'old' user.
That should do it.
Clinton -
I dropped my iPhone 4 in water and now it won't turn on at all, will i lose all of my data, for example my photos and messages etc? and is there any way you can back the phone up without having it switched on?
If you had previously been backing up to iCloud (or a computer with iTunes), you would possibly have a backup. That said, if you can't turn the phone on, you cannot create a backup of the device now. Sorry.
-
Having to switch off my Iphone just to get a connection to the internet and also receive Imessages
Hi all,
I have recently updated my Iphone 5 to the Iphone 6 in the hope that it would eliviate some of my problems with the Iphone 5, thinking maybe it could be a problem with the phone...alas still the same problem!
Basically I can connect to the internet via Safari or even use App's that require an internet connection for a few times in a day, however after about a third of fourth time of using it I can no longer connect. The only way I can fix the problem is having to switch my Iphone off and on again, then it finally works! I am having to do this now several times a day most days. I am also having delays in sending and receiving Imessages, some are taking up to a day to be received even though showing as sent on the senders phone. Likewise when I switch the Iphone off the messages come through....Its exactly the same with my Iphone 6 which is two days old! Help!!
Thank youIt the problems that you are seeing are ones that you had on an iPhone 5 and they followed you to the iPhone 6, I would believe there is something wrong with the backup of your old device. Did you restore the new phone from the backup of the old device? Try restoring the phone as new and then test it before adding any content back. If the phone works correctly, then there is corrupt data in your backup. Rather than restore to the backup, just sync your data back to the device individually.
-
Impact of having the fsmo role holders not available for 14 hours...
Hi everyone, we have a situation where we will lose power to the building for 14 hours and since we don't have a generator we'll be shutting down our main site. We have 15 sites, each has a dc and the hq site has two with the fsmo roles distributed between
the two at hq. So two questions to start with:
1. What will be the impact of having the fsmo role holding domain controllers inaccessible for a period of 14 hours?
2. What will we be facing once we regain power and turn the hq dc's back on?
Look forward to hearing back about this - the power outage is this weekend though!!Hi,
Sorry for the delay reply.
If your PDC Emulator fails, certain domain functions, security functions, can stop functioning. If anyone of the following is not happening then you should check if your PDC Emulator is working properly:
•Time is not Syncing: PDC is the default source for the client computers to sync the time. If client computers are not syncing the time then you should always check the PDC.
•User accounts are not locked out: PDC Emulator processes the account lockouts immediately for the entire domain.
For more detail information, please refer to:
FSMO - if server holding PDC Emulator fail on 2003 / 2008, what happen?
https://social.technet.microsoft.com/Forums/windowsserver/en-US/1752b861-53d7-49f5-b066-2ca6a18070e7/fsmo-if-server-holding-pdc-emulator-fail-on-2003-2008-what-happen?forum=winserverDS
Regards.
Vivian Wang -
How to disable Switch Profile and Auxilliary Metadata set on UCM checkin screen?
We are using webcenter content 11.1.1.6 with Record Management component installed on top of it
While trying to checkin a new document from a normal checkin screen or from Manage attachments screen two options come at the top 'Switch Profile and Auxilliary Metadata set'
How can these options be disabled?Hi,
The xExternalDataSet is already an empty string on the check in page
When i append &IsJava=1, the variables have these values
xExternalDataSet=
xExternalDataSet:isInfoOnly=1
xExternalDataSet:isSetDefault=1
Isn't there a config variable for this, as I see this component has come as part of record management but no option to disable when I configure record management
Thanks,
Gaurav -
Nexus 5020 Switch Profile Error
Hi There,
I have 2 x 5020s peered together with a switch profile. Somehow the switch-profile configurations have gone out of sync.
1st 5020
switch-profile : xxxx
Start-time: 889959 usecs after Tue Aug 9 12:25:47 2011
End-time: 453948 usecs after Tue Aug 9 12:26:36 2011
Profile-Revision: 188
Session-type: Commit
Session-subtype: -
Peer-triggered: Yes
Profile-status: Commit Failed
Local information:
Status: Commit Failure
Error(s):
Failed command(s):
h
Peer information:
IP-address: 10.87.249.12
Sync-status: In Sync.
Status: Commit Failure
Error(s): Commit failed on peer.
2nd 5020
switch-profile : xxxx
Start-time: 831600 usecs after Tue Aug 9 12:25:47 2011
End-time: 326942 usecs after Tue Aug 9 12:26:36 2011
Profile-Revision: 186
Session-type: Commit
Session-subtype: -
Peer-triggered: No
Profile-status: Commit Failed
Local information:
Status: Commit Success
Error(s):
Peer information:
IP-address: 10.87.249.11
Sync-status: In Sync.
Status: Commit Failure
Error(s):
Failed command(s):
h
I am now unable to make changes to the switch-profile config. I know exactly where the difference is in the config. It is the description on one of the Ethernet interfaces
interface Ethernet173/1/44
description *** Server D4 ILO 10.87.103.51 ***
switchport access vlan 31
spanning-tree port type edge
interface Ethernet173/1/44
description *** Server D4 ILO 10.87.103.62 ***
switchport access vlan 31
spanning-tree port type edge
How can I recover from this and sync up both the profiles to the same revision?Hi,
Manually fix the description on one side so that both side look equally. (just conf term not conf sync)
Then it shoul sync again. But try to sync from both switches - I've the situation that it config sync succseeds from one side but not from the other. -
Hello Experts,
On a Nexus 5000 in VPC domain, I look for the result of commited switch profile.
Where can I find this kind of information (in bold), in which MIB ? Do you have the OID ?
SW11B2D01# show switch-profile YOP status
switch-profile : YOP
Start-time: 873633 usecs after Wed Jun 11 12:03:04 2014
End-time: 101711 usecs after Wed Jun 11 12:03:30 2014
Profile-Revision: 11
Session-type: Commit
Session-subtype: -
Peer-triggered: No
Profile-status: Sync Success
Local information:
Status: Commit Success
Error(s):
Peer information:
IP-address: 1.1.1.1
Sync-status: In sync
Status: Commit Success
Error(s):
Thanks for your help,
Pauloups you're right
The two lines are :
Sync-status: In sync
Status: Commit Success
Thanks
Paul -
Having issues with profile manager on 10.9 loosing users/device assignments.
I'm having issues with profile manager on 10.9 loosing users/device assignments. Luckly I only have arround 70 devices added so far. The first time it happened I thought it was just a freak thing, but it has just happened again. What I find weird is nothing on the server was changed, no devices added. So when this happens my users phones lose access to email, because I'm using variables, which rely on the user being assigned to the device. Anyone know how to fix this, and if not. Does anyone know how to backup and restore just profile manager in 10.9. Thanks.
I enabled all users in my AD "Domain Users" group access to "Profile Manager". I had also initially enabled "Profile Manager" access for a few individual users. Those users did not loss the device assignments. I'm not absolutely sure why/if allowing access for a group is causing this issue. Enabling access for each person would be very time consuming.... Maybe adding access to the individual users is importing that user into OD?
-
I was trying to upload a video clip to iMovie and I got a popup saying that there was an upload error. I switched profiles, came back, and when I opened iMovie it said that it was uploading my clip, but it hasn't shown any progress and won't close iMovie.
Post in the iMovie forum.
-
TS1814 we bought an ipod touch and are having trouble switching from old ipod to the new one
we bought an ipod touch and are having trouble switching from old ipod to the new one
OK.
If you have a question, then explain your issue and ask it. -
Nexus 5000 switch-profile sync via SVI?
Hi,
is it possible to use a Vlan interface (SVI) for syncing the switch profile on two 5596?
I tried this:
2 x 5596UP with NX-OS 5.2(1)N1(3)
Connected with 2 x Twinax on ports Eth1/15 and /16, portchannel 3.
The Po3 is a trunk, allowed Vlan is 439. Both 5596 have a SVI in Vlan439 with an IP. I can ping between the two 5596.
# ping 10.9.8.4
PING 10.9.8.4 (10.9.8.4): 56 data bytes
64 bytes from 10.9.8.4: icmp_seq=0 ttl=254 time=0.887 ms
When I try to to this:
switch-profile k
sync-peers destination 10.9.8.4
I get:
# sh switch-profile status
switch-profile : k
Start-time: 831222 usecs after Thu Aug 15 17:57:53 2013
End-time: 834086 usecs after Thu Aug 15 17:57:53 2013
Profile-Revision: 7
Session-type: Initial-Exchange
Session-subtype: Init-Exchange-All
Peer-triggered: No
Profile-status: -
Local information:
Status: -
Error(s):
Peer information:
IP-address: 10.9.8.4
Sync-status: Not yet merged
Merge Flags: pending_merge:1 rcv_merge:0 pending_validate:0
Status: Peer not reachable
Error(s):
As soon as I change the sync-peers destinations to use the IPs on the mgmt0 interface everything works fine:
# sh switch-profile status
switch-profile : k
Start-time: 723075 usecs after Thu Aug 15 18:04:23 2013
End-time: 475957 usecs after Thu Aug 15 18:04:25 2013
Profile-Revision: 7
Session-type: Commit
Session-subtype: -
Peer-triggered: No
Profile-status: Sync Success
Local information:
Status: Commit Success
Error(s):
Peer information:
IP-address: 10.0.0.4
Sync-status: In sync
Status: Commit Success
Error(s):No, if you want a short answer.
Or...
Switch-Profiles feature will only work using mgmt0 interface. Here's the quote from
Cisco Nexus 5500 Series NX-OS System Management Configuration Guide, Release 6.x
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5500/sw/system_management/6x/b_5500_System_Mgmt_Config_602N12_chapter_011.html
Guidelines and Limitations for Switch Profiles
Consider the following guidelines and limitations when configuring switch profiles:
You can only enable configuration synchronization using the mgmt0 interface.
-- the rest of output is cut for brevity --
Cheers
Tim
P.S. Please rate this post. -
Nexus 5596 switch-profile synchronization problem
hi
I can't synchronize switch-profile
System version: 5.1(3)N1(1)
Sync-status: Not yet merged
Merge Flags: pending_merge:0 rcv_merge:1 pending_validate:1
Status: Verify Failure
Error(s):
Following commands failed parsing: If the error is 'Command Parsing Failed', please check if some conditional feature(s) needs to be enabled
switchport mode trunk (Command Parsing Failed)
how to find the source of the problem ?Hello Pawel
Can you attach following from both Nexus 5596 switches in question
term length 0
show version
show run
show tech-support port-profile -
Switching profiles in Airport Express
I have an old airport express (1st gen) that allows me to use multiple profiles (I use it at home to extend my wireless network and have a travel profile to create a wifi network). Do I need to use my computer to change the profile before unplugging the airport express at home and taking it with me wherever I am going, or will it switch automatically when I connect it to an ethernet cable, and back to extend my netword when I plug it back at home? This is not so easy now because I can only manage profiles with Airport Utility 5.6, which I only downloaded at my desktop but do not have in my notebook, ipad or iphone.Thanks
Ricardo231 wrote:
... Do I need to use my computer to change the profile before unplugging the airport express at home and taking it with me wherever I am going,
Yes. The Express will not automatically change from one stored profile to another, so you must switch profiles yourself.
This is not so easy now because I can only manage profiles with Airport Utility 5.6,
That is a moot point since a first generation Express requires AU 5.6 anyway.
Maybe you are looking for
-
I would like to know how to change my asus operative system windows 7 to mac snow leopard i have an asus K53E i have an iphone 4 three ipods and a time capsule and is really dificult to make them work with windows. please someone help me....
-
I've been reading a number of posts about how to arrive at a shorter URL for iWeb sites; many seem to involve either using some other site or registering a domain name - I administrate five already, I don' need no more steenkin' domains. Anyway,... I
-
Missing red color in adobe RGB
I shoot raw with Nikon Camera. I am having a problem with getting red color in photoshop. . For nef files, I open them in Capture NX2 and then save as jpg in Photoshop. The jpg image was opened in Photoshop CS5 with a color setting of sRGB, beatiful
-
When will there be a "save as" toolbar button in ver 15 like there was in older versions?
in ver 13 [I think] I had a toolbar button that I used to save the web page I was on It was "save as" not just "save" when is Firefox going to make the new button available or where can I find a version of "save as" somewhere else?
-
Trouble Downloading Images to LR4
I am using a USB card reader to download images to LR4. When I plug the reader into the USB port I get an error message saying, "images on card do not meet download criteria". The thumbnails appear in Library mode but when I click on "Import", anothe