Important memory information for A64 owners
I just found an interesting read at Anandtech comparing many 2-2-2-x timing RAM sticks against each other. Near the end of the article there was a mention of performance with Athlon64 based systems. It appears that many of the Samsung based memory chips(Corsair, Kingston, Mushkin) have difficulties with the Athlon64 and could cause some issues, especially past DDR433.
It appears that the Micron memory chips are very good performers with the Athlon64. So if you are looking for memory for your new Athlon64 system, you should consider Crucial Ballistix or OCZ Enchanced Bandwidth memory.
What caught my eye is that all testing for the Athlon64 was done on the MSI K8N Neo2 Platinum, so these results especially apply to us.
Here is a link to the article:
http://www.anandtech.com/memory/showdoc.aspx?i=2145&p=19
Yep many to many folks had issues with Corsiar memory even with the K8T800 boards too. So it is the memory and not the boards. When I built my system clear back in the spring I saw all the issues with corsiar and decided on Kingmax instead. I have been happy and never had to look back and wonder. I would not touch Corsiar with a 10' pole.
Similar Messages
-
How do I import GPS information for all of my images from Bridge into Lightroom 5.3?
After importing my images into Lightroom 5.3, I discovered that the GPS location data was imported for some images, but not for others. When I checked the metadata files for the same images in Bridge, the location data was present for all of my recently downloaded images.
Why would Lightroom import the GPS data for some images and not others?
Is there any way to import the location data from the Bridge metadata files into Lightroom?Tony,
Thank you for your suggestion. I had already tried several approaches along those lines without success. In the end, the GPS data was still present in Bridge metadata file for each image, but not in the Lightroom metadata files for the same images.
So, I went back to Lightroom, and did some further exploring on the internet for solutions. Just as I was wondering whether or not the problem might be rooted in my download presets (i.e., setting copyright into, etc.), I stumbled across a reference by a Pentax owner that identified the same problem. Here's the link:
http://www.pentaxforums.com/forums/115-pentax-k-5/203274-gps-data-not-importing-into-light room-4-2-a.html
In a nutshell, I can download all of the metadata, including the GPS location information, but only if I do NOT use any metadata presets. If I use a metadata preset when downloading my images, no GPS data can be seen in the Lightroom metadata files, but it does import into Bridge's metadata files. I've now tried this both ways, several times now, and have verified this result.
I also tried re-downloading images with no presets, and replacing (copying over) the image from my original download. This did not solve the missing GPS data in the Lightroom metadata. From this point, all that I could think of doing was removing all of my recent downloads from Lightroom, and starting over. However, I'd already started editing my images, and I didn't want to lose that time.
So, I re-downloaded all of my recent images from my memory cards as a copy into each file without any metadata presets. Then, after selecting the copy first, followed by selecting the original (order is important), I toggled 'Sync Metadata' under the Metadata tab in Lightroom. Voila, the GPS data appeared in the original metadata. When this is done for all of my images, I will delete the second copies in my files. Once I am satisfied that everything is okay, and my images are backed up satisfactorily, and only then, will I reformat my memory cards.
This whole experience has surfaced an interesting quirk in Lightroom, or in my Lightroom settings that I don't understand. It may be something that Adobe might want to look into further, if others are finding a similar problem. -
Incorrect Memory Information for Canon EOS 7D on BB
I hate to keep pointing out your errors, but I also hate to see you have people angry at you. I sort of didn't believe that Canon would move away from CF (compact flash) cards for this camera yet in the overview and specifications you talk about :
Built-in media card
Supports Secure Digital, Secure Digital High Capacity, MultiMediaCard and MultiMediaCard Plus formats for fast and convenient image storage. Records RAW, JPEG, DPOF and MOV images.
So I went directly to the Canon website and there is no built in media card, and the memory card is still, indeed, a compact flash--not SD, SDHC or MMC, MMC+Hi Titania41,
I have to say thank you for making us aware of this, and I have passed along this information to the people here at corporate that can correct this. You are correct on both counts. This camera doesn't have a built-in memory card, and it uses Compact Flash memory cards.
Thanks for posting,
Allan|Senior Social Media Specialist | Best Buy® Corporate
Private Message -
Problem with Import Computer Information Wizard not doing check for MAC or GUID already in database
Hi,
My client is using SCCM 2012 RTM in a standalone site.
Yesterday, a technician was preparing computers to deploy OS. He was in a replace scenario and mistakenly mixed the MAC address of the source computer with the one of the new computer.
So when importing computer information for the new one, he entered the wrong MAC address; the one of the source computer already existing in the SCCM database.
I expected the Import Computer Information wizard to generate an error, but no, the import was successful resulting with the source computer DDR being overwritten...
We spent (and lost) time recreating the DDR for the source computer so we could create the computer association for USMT migration.
2 years ago, I opened a call with Microsoft for the exact same issue with SCCM 2007. At that time, they told me that no hotfix would be developped for this bug since there was a workaround (overwritten DDR will re-create itself with Heartbeat
discovery over time) and SCCM 2012 was coming up.
It seems to me that they forgot to fix the issue in 2012. It doesn't seem to be fixed with SP1 as I didn't find anything about it in SP1 doc..
Can someone confirm this bug and can Microsoft do something? Or is there a hotfix already available for it?
Tnx
PatrickWell you could always remove the Delete Resource permission from the technicians User Rights :P
The option to not overwrite the existing computer object, is right there in the SDK.
So it's anyone's guess, why they haven't added an checkbox in the Import Computer Information wizard and why overwrite is set as the default.
Anyways...you can use the following PowerShell script instead of the Import Wizard.
Just open up a PowerShell console, type in . X:\Path\To\Script\ScriptName.ps1 and
then type New-SCCMComputer
Or you can create a shortcut with the following target %SystemRoot%\system32\WindowsPowerShell\v1.0\powershell.exe -NoExit -Command . X:\Path\To\Script\New-SCCMComputer.ps1; New-SCCMComputer
You will need to change the default values for $SiteServer and $SiteCode to your environment
Function New-SCCMComputer
[CmdletBinding()]
Param(
[Parameter(Mandatory=$False)] $SiteServer = "Server.Domain.Local",
[Parameter(Mandatory=$False)] $SiteCode = "PS1",
[Parameter(Mandatory=$True,HelpMessage="Please Enter the Computers Name")] $ResourceName,
[Parameter(Mandatory=$True,HelpMessage="Please Enter the Computers MAC ")] $ResourceMAC
#ImportComputer
$WMIConnection = ([WMIClass]"\\$($SiteServer)\root\SMS\Site_$($SiteCode):SMS_Site")
$NewEntry = $WMIConnection.psbase.GetMethodParameters("ImportMachineEntry")
$NewEntry.MACAddress = $ResourceMAC
$NewEntry.NetbiosName = $ResourceName
$NewEntry.OverwriteExistingRecord = $False
$Resource = $WMIConnection.psbase.InvokeMethod("ImportMachineEntry",$NewEntry,$null)
if ($Resource)
if ($Resource.MachineExists) {
Write-Host "ERROR: MACAddress allready exists" -foregroundcolor red
} else {
Write-Host "Succesfully imported the computer information" -foregroundcolor green
} else {
Write-Host "ERROR: Could not import the computer information" -foregroundcolor red
Best Regards
Claus Codam
Consultant, Developer
Coretech -
Blog -
Hey guys. Bought the new Ministry Of Sound album, The Annual 2014 and went to import the music onto iTunes.
The album is on the online store as I was tempted to purchase it there, in hindsight I wish I had, however I didn't and now the information for the CD cannot be found online and insists I could put all 40 odd songs and all it's data into iTunes myself.
I am happy to do that if I must, but surely if the iTunes store has all the information for the album I can transfer all of it to the CD.
If not what else could I do?
ThanksThe CD track identification in iTunes queries information from the Sony/Gracenote database, and interestingly, has nothing to do with the iTunes Store.
You might as well go ahead and type it in. If you wish to be a good citizen, you can then use the iTunes "Submit Track Names" feature to submit to Gracenote, so that your fellow MoS fans will save typing. -
I found an ipod touch with important medical information - how do I return it to its owner?
I found an ipod touch in Toronto today. No identifying info on it but possibly important medical information.
Happy to help reunite it with its owner.Report to police too.
Also go to Settings>iTunes and App stores and send an email to the Apple ID email address if different from the iCloud ID address. -
My MacBook Pro 2012 Mountain Loin 8.2 doesn't clear the inactive memory automatically when memory needed for other program so I get page outs. There are much inactive memory when page outs. Why my mac does this?
That's completely normal. If other programs require memory then the system will reallocate Inactive RAM as needed. Page Outs don't mean anything.
About OS X Memory Management and Usage
Reading system memory usage in Activity Monitor
Memory Management in Mac OS X
Performance Guidelines- Memory Management in Mac OS X
A detailed look at memory usage in OS X
Understanding top output in the Terminal
The amount of available RAM for applications is the sum of Free RAM and Inactive RAM. This will change as applications are opened and closed or change from active to inactive status. The Swap figure represents an estimate of the total amount of swap space required for VM if used, but does not necessarily indicate the actual size of the existing swap file. If you are really in need of more RAM that would be indicated by how frequently the system uses VM. If you open the Terminal and run the top command at the prompt you will find information reported on Pageins () and Pageouts (). Pageouts () is the important figure. If the value in the parentheses is 0 (zero) then OS X is not making instantaneous use of VM which means you have adequate physical RAM for the system with the applications you have loaded. If the figure in parentheses is running positive and your hard drive is constantly being used (thrashing) then you need more physical RAM.
Adding RAM only makes it possible to run more programs concurrently. It doesn't speed up the computer nor make games run faster. What it can do is prevent the system from having to use disk-based VM when it runs out of RAM because you are trying to run too many applications concurrently or using applications that are extremely RAM dependent. It will improve the performance of applications that run mostly in RAM or when loading programs. -
Memory upgrade for KM3M-V mobo (aka MS 7061-01S)
Hi, this is my first post. I've read the guidelines and searched for an existing topic but can't find one that quite matches what I want to ask, so I'm posting a new topic - please forgive me I have erred!
I have a TIME Computers desktop (please don't ask why), mobo being a MSI KM3M-V (also known as MS7061-01S), which is based on VIA KM266 chipset. CPU = Sempron 2400+.
I've just installed a new graphics card, an ATI All-in-Wonder 9200SE, with associated drivers and software including Catalyst (which menat I had to instal MS .net framework too). This seems to be working OK but overall speed not great. (Also, for some reason I don't seem to be getting any sound at all, but I expect I can fix that with a bit of trail and error.)
My next step is to increase the memory. Existing memory installed is one 256MB UDIMM module, but I'm aiming to remove it and instal 2 x 1GB UDIMM modules, which I know the mobo can take. Naturally I'm looking to get the maximum available performance (subject to stability considerations), so I'm looking to go for the highest bandwidth/speed the system can take. This is where it gets tricky. Having searched Crucial, Kingston and other memory configurators plus various other tech articles and indeed MSI's own website, I've reached the conclusion that I can select memory in PC2100/ 2700/ etc up to 4000 or even higher provided that the maximum memory chip size (density) does not exceed 128MB.
But I'm not sure about the speed limitation: is there any point in buying DIMMs capable of DDR333 or 400 - will my chipset limit the speed to 266MHz anyway? I'll be grateful for any expert views.
Operating System: Windows XP Home Edition (5.1, Build 2600) Service Pack 2 (2600.xpsp_sp2_rtm.040803-2158)
Language: English (Regional Setting: English)
System Manufacturer: Time Computers
System Model: KM266-8237
BIOS: Phoenix - AwardBIOS v6.00PG
Processor: AMD Sempron(tm) 2400+, MMX, 3DNow, ~1.7GHz
Memory: 192MB RAM
Page File: 135MB used, 331MB available
Windows Dir: C:\WINDOWS
DirectX Version: DirectX 9.0c (4.09.0000.0904)
DX Setup Parameters: None
DxDiag Version: 5.03.2600.2180 32bit UnicodeThanks for the quick reply, Exo. I agree with you 100% that it's best to go for (at least) PC3200 with a view to a likely future upgrade. As I see it, it makes sense to go for the highest spec available at reasonable cost - so I would probably aim for PC4000 rather than 3200. There doesn't seem to be any downside in doing so (provided one is happy to tweak the BIOS where necessary), and even the MSI MOBO spec seems to endorse this view - see bit picked out in red below:
http://www.msicomputer.com/product/p_spec.asp?model=KM3M-V&class=mb
Main Memory
• Supports four memory banks by using two 184-pin DDR DIMMs
• Supports a maximum memory size of 2GB.
• Supports 2.5v DDR SDRAM DIMM
Due to the High Performance Memory design, motherboards or system configurations may or may not operate smoothly at the JEDEC (Joint Electron Device Engineering Council) standard settings (BIOS Default on the motherboard) such as DDR voltage, memory speeds and memory timing. Please confirm and adjust your memory setting in the BIOS accordingly for better system stability.
Example: Kingston HyperX DDR500 PC4000 operates at 2.65V, 3-4-4-8, CL=3.
For more information about specification of high performance memory modules, please check with your Memory Manufactures for more details. -
Title says it all.
I'm really getting sick of websites getting more and more into your business. Google forcing you to get a G+ account and asking for your identifying information, for example (like your phone number).
It's extremely irritating, and I'm opting out of everything that enforces the such. If Apple begins pushing like this, I will just close my relationship with the company and obtain apps by using third-party software to force them onto the phone.
But before going that far, I'd like to find work arounds.
First of all, I don't even know why it asks me for my "state". I don't even live in the USA anymore, as I moved to China (though I won't use the Chinese store as I don't speak or understand the local language, which is Chinese).
All I want... is to continue using the English App Store to get free apps from here in my home in China, without getting stopped by Apple asking for more info on me. I don't want to share my name, I don't want to share my address, and I can't even complete the form as I no longer have a "state" and don't have any credit info.
So that's just that. If there's no way around it I'll find another way to install apps without the App Store.
Sorry for the message tone, I'm just really irritated with the way the internet is getting.
Thanks in advance!
- AlexThe living issue is complex in my case. Legally speaking, I have no personal residence globally. I just live wherever my father goes, which is everywhere. I'm an expat and it seems that these sites aren't really expat-friendly. They seem to be built for localization and assume everyone stays in the same place.
I don't know what I'd be considered. I'm a US passport holder and live in China, but I only speak some Chinese and I can't read it (it using non-latin characters is just too much for my mind's memory to handle). Besides that, I'm not interested in popular Chinese apps. They tend to just be annoying and kooky and generic and put together badly, often full adware and spyware (speaking for most Chinese software, in fact). In fact, a lot of apps I want are illegal in China (YouTube, Facebook, etc) and I use a VPN to use the services. I assume I wouldn't find these apps on the Chinese store. In fact, last I checked, there wasn't many English apps on the Chinese app store. This is probably due to their strict moderation or something.
I've been going to international schools since I got here and college would be in English too. I can speak some Chinese, but not read it.
Well, I guess the answer is that I can't use the App Store in English. So I guess I'll just sign out everything on my phone involving my Apple account and just start using third-party tools to do my business. -
My iphone 4s is importing contact information from FB and my e-mail account. When I try to look at my contact list it is showing everyone I have on those lists and it only shows their email addresses. The phone numbers for my contacts have disappeared and I don't know how to get them back.
Hi macmac57. I don't memorize my numbers anymore, so I know how important it is to have all your contacts on your phone at all times. Did an update occur or a new application download when your contacts disappeared? Have you been backing up your device with your computer? You can try to restore your contacts from your last backup. http://support.apple.com/kb/HT1414
Are you syncing your iPhone between multiple computers? This can sometimes create issues with your contacts. http://support.apple.com/kb/TS1474
If you were already using iCloud to back up your contacts, check out http://support.apple.com/kb/TS3998 for some great tips from Apple.
I do hope this has been helpful for you to restore your contacts.
JenniferH_VZW
Please follow us on Twitter @vzwsupport -
How can I change game centre and iCloud account information from previous owner of my iPad?
How can I change game centre and iCloud account information from previous owner to me?
You can't do it on your own. The previous owner has to erase the device for you. You would need his Apple ID and password in order to delete his iCloud account. This is due to the Activation Lock in iOS 7 - assuming that your iPad is running iOS 7.
Contact the owner and ask home to erase it remotely using iCloud, or return the device and ask for your money back. If you can't contact the pervious owner, you will have a useless iPad on your hands.
Read this for more information. This is what you need the previous owner to do.
What to do before selling or giving away your iPhone, iPad, or iPod ... -
"Dependecies" tab doesn't show any information for a selected table version 4.0
Hello,
I work with SQL Developer 4.0.0.13. I can see 20 tables in the list. When I select one table, in the tabs on the right side I can see information for "columns" and "data" and "constraints" and "indexes"... but the tab "Dependencies" doesn't show any information about references between this table and other tables in the schema.
Oracle database is v11.2
Can you please tell me what do I need to do in order to see information on "Dependencies" tab for a table?
Thank you,
MilanHi, here is my example of XML extension showing referencing tables:
Save the following XML to a file.
<items>
<item type="editor" objectType="TABLE">
<title><![CDATA[*Referencing Tables]]></title>
<query>
<sql><![CDATA[SELECT
cfk.owner "OWNER",
cfk.table_name "TABLE NAME",
cols.column_name "COLUMN",
cfk.constraint_name "CONSTRAINT NAME",
cfk.delete_rule "DELETE RULE",
'SQLDEV:LINK:' || cfk.owner || ':TABLE:' || cfk.table_name ||
':oracle.dbtools.raptor.controls.grid.DefaultDrillLink' "LINK"
FROM
sys.all_constraints cpk,
sys.all_constraints cfk,
sys.all_cons_columns cols
WHERE
cpk.owner = :OBJECT_OWNER AND
cpk.table_name = :OBJECT_NAME AND
SUBSTR(cpk.table_name, 1, 4) != 'BIN$' AND
SUBSTR(cpk.table_name, 1, 3) != 'DR$' AND
cpk.constraint_type in ('P', 'U') AND
cfk.r_owner = cpk.owner AND
cfk.r_constraint_name = cpk.constraint_name AND
cfk.constraint_type = 'R' AND
cols.owner = cfk.owner AND
cols.constraint_name = cfk.constraint_name
ORDER BY
cfk.owner, cfk.table_name, cfk.constraint_name,
cols.column_name]]>
</sql>
</query>
</item>
</items>
In SQLDeveloper select Preferences -> Database -> User Defined Extensions and click <Add Row>.
In the "Type" field enter "EDITOR" and in the "Location" field enter the path to the file with XML.
After restarting SQLDeveloper You should see a new tab "*Referencing Tables" for tables. -
I have lost my iphone 3GS. It was backed up to my macbook pro using itunes. I now have a new iphone series 4 (china model). How can I access the backup information for my old phone and put it on my new one?
Thank you again for all of your help!! I really appreciate it!
I think I am following -- I was able to upload to my iPhoto and all photos and videos are there that is a plus! I tried to create an Event in my iPhoto and put all of my photos in that event but for some reason, now my iTunes it not recognizing that Event in my iPhoto. It is not allowing me to import just that event at the moment but I may be doing something wrong. At least all of my pics and vids are in iPhoto so that is a plus and I know they are at least saved somewhere. Just for some reason, my iTunes it not locating the event that I created with only those photos.
Thank you for letting me know about my contacts! How do I know if I have the contacts app?
Also, I had no clue that my iCloud could be backed up via cellular data! However, is this a new feature with the most updated iOS?? Unforutnatly I am like 2 iOS updates behind because I don't have enough storage on my phone. I still get the notification that my phone needs to be plugged in and connected to wifi in order to back up to the cloud :-(
How can I sync using USB? Right now when i click on the info tab for my iPhone in my iTunes this is the answer that I get -- I am a little unclear as to what it means.
Sync Contacts:
Your contacts are being synced with you iPhone over the air from iCloud. Over-the-air sync settings can be changed on you iPhone
Sync Calendars:
Your calendars are being synced with you iPhone over the air from iCloud. Over-the-air sync settings can be changed on you iPhone -
i reset my disabled ipad 2 and it is asking me for the apple id which first set it up but i forgot the password for that apple id and the password/recovery information for the recovery email address. What can i do?
Click here and use Apple's iForgot service, or contact their Account Security team, or if you're the device's original owner, take it and its purchase receipt to a physical Apple Store.
(124525) -
Hi All,
In production sometimes a data load fails because of the less ABAP memory available.
For a perticular load ABAP memory goes till 4 Gb and more and after that load fails with short dump.
This time i change a start routine logic and split a complex start routine logic in two programs.
Now i want to check about what memory my new programs are taking.
1. One of the programs is in start routine itself .
2. Second program is SE38 program.
How I can see the memry consumption while data load.
thanks
MukeshHI
SAP memory is for cross-transaction Applications and ABAP/4 memory is transaction-specific. So you can use SQL Trace to see the back ground process tables and details for the same Transaction.
The SAP memory, otherwise known as the global memory, is available to a user during the entire duration of a terminal session. Its contents are retained across transaction boundaries as well as external and internal sessions. The contents of the ABAP/4 memory are retained only during the lifetime of an external session. You can retain or pass data across internal sessions.
The SET PARAMETER and GET PARAMETER statements allow you to write to, or read from, the SAP memory. The EXPORT TO MEMORY and IMPORT FROM MEMORY statements allow you to write data to, or read data from, the ABAP memory.
ABAP memory is a memory area that all ABAP programs within the same internal session can access using the EXPORT and IMPORT statements. Data within this area remains intact during a whole sequence of program calls. To pass data to a program which you are calling, the data needs to be placed in ABAP memory before the call is made. The internal session of the called program then replaces that of the calling program. The program called can then read from the ABAP memory.
Put function group memory in ABAP-MEMORY-- BAL_GLB_MEMORY_IMPORT Get function group memory from ABAP
Hope it helps
Maybe you are looking for
-
Why can't I download a PDF from a web site with Safari?
I clicked on an image whcih is suppoed to open a PDF. Nothing happens.
-
Poor graphics redraw when scrolling Word documents
I have a strange blurring effect when scrolling Word documents on my Macbook pro, as if the graphic card had trouble refreshing: the screen is interspersed by horizontal irregular lines that make it impossible to read the text. I have recently replac
-
What next after updating the Ipad?
I have now managed to reconnect my Ipad after updating it and I have lost some of my photos, all of my music, and all of the apps which I have both paid for and which were free. How do I get those back, surely I don't have to pay again do I?
-
I have a iMac with Lion 10.7.4. Ive had to turn Photo Stream on several time in order for pictures to download. Should Photo Stream stay on?
-
how do i back up my music so when i send it in to get repaired i can easily transfer all my music back into my iPod and can i put all the songs form my iPod into my computer? thx for helping