Importing cr2 raw files won't work on ios 6 when it worked fine on ios5. Anyone have a solution?

I have been importing cr2 raw files to my iPad using ios 5 but importing cr2 raw files won't work on ios 6. Sees files in camera but when import stops it fails with an exclamation mark in red circle. Anyone have a solution?

Don't know if you care anymore or it applies, but I was able to get things working but it took drastic measures.
I had to do a full system reset and update by doing the following:
- Make note of all your settings in your system and apps especially accounts and forget about in app data that's only on your iPad and not in a cloud service because it will be gone after this
- Connect iPad to Mac and startup iTunes
- Hold down Home and Power buttons simultaneously for about 8 sec until the screen turns black
- Release the Power button but continue holding the Home button until there's a popup on your screen which indicates it's in recovery mode
- Follow the instructions to recover your iPad but recover it to factory state, not recover from a backup
- Reinstall all your apps and content
- Reconnect to all your services on your system and apps
I could not restore from a backup since it brought back my bad data too. It also didn't restore my music and no matter what I tried it wouldn't put my music onto my iPad. Had to start clean.
It appears over time that the system gets dirty and there's lots of bad data that can't get resolved. This is especially true if some of your apps have crashed a bunch.

Similar Messages

Canon CR2 Raw files won't open in Photoshop CS4

I'm using a Canon EOS 600D (aka EOS Kiss X5), Photoshop CS4 (ver 11.0.1) with Camera Raw 5.7.0.213.
CR2 Raw files won't open in Photoshop, though the thumbnails are clearly visible and open in Windows Explorer.
Any suggestions?
Thanks

Yes, absolutely all of the quality and dynamic range is retained in the DNG, because it is still raw data.
Outside of upgrading to Photoshop CS5, which can open your files directly with Camera Raw 6.4.1, your only choice is the extra step of converting the .CR2 files to .DNG with the free DNG converter.
While you'll get all the quality your Camera Raw 5.x converter can deliver, you should keep in mind the Camera Raw 6.x converter has an entirely new, additional "2010 process" for converting raw images, which (depending on your settings) can actually deliver a higher quality conversion than the one you're getting with Photoshop CS4. I think it's worth the cost of the Photoshop upgrade, personally.
-Noel

Import of raw-files to iphoto is impossible since yosemity and iphoto 9.6 - is there already a solution?

Import of raw-files to iphoto is impossible since yosemity and iphoto 9.6 - is there already a solution?
Macbook Pro 2011 and Macbook Air 2011 -
Krs Benne49

What camera are you using? The RAW support is camera specific. Have you installed the latest Digital Camera Raw update 6.01?
If you are already running the latest raw support, try to reinstall:
To reinstall you need to exchange files in the System Library. So be sure to backup your computer before patching the system library.
The RAW support files are installed in the System Library in the folder "/System/Library/CoreServices" Folder:
To open this folder, use the Finder's "Go" menu. Click the smiling Finder icon in the Dock to bring the Finder forward.
Then type the keyboard shortcut ⇧⌘G (for "Finder > Go > Go to folder") and copy and paste "/System/Library/CoreServices" into the text field.
In the Finder window that will open, delete both the files "RawCamera.bundle" and "RawCameraSupport.bundle". You will have to enter your Administrator password.
Download the current RAW support update from Apple's Support Site: Digital Camera RAW Compatibility 6.01
In the Downloads folder you will find the disk image with the installer. Double click it to open and run and the installer.
Then restart your Mac.
If the current support is still causing the problems after reinstalling, try to downgrade to Digital Camera RAW Compatibility Update 5.07

I have an iPhone 4 on IOS5. I signed up for itunes match. After everything uploaded to the cloud, my songs are messed up. I'll select a song and the title will show with the right art work but a different song will start playing. Anyone have a solution?

I have an iPhone 4 on IOS5. I signed up for itunes match. After everything uploaded to the cloud, my songs are messed up. I'll select a song and the title will show with the right art work but a different song will start playing. Some songs won't play at all even though they do appear in the itunes store. The artwork almost always shows u blank until you turn it to landscape then it will appear. Anyone know what's going on?

I have found that scrolling through the album list (past albums without art) triggers the progress wheel next to the wifi symbol. You can scroll quickly through the whole collection and then wait! Artwork will appear gradually...
However, repeat visits to the Music App might initially show no artwork again, but it might spontaneously appear more quickly this time. The bad news is that the whole Music App is now sluggish as ****...

I have a Belkin USB N150 Wireless Adapter used since my airport card broke. It worked in mountain lion however no longer works when i updated to mavericks. Anyone have a solution to this?

Is there anyway to fix this, or is there a way to downgrade back to mountain lion?

Hello melissanelson110,
If you've backed your Mac up with Time Machine, you may be able to revert to Mountain Lion by restoring from your backup.
OS X Mountain Lion: Revert to a previous OS X version
http://support.apple.com/kb/PH11181
Cheers,
Allen

Lightroom 3 Corrupting .CR2 RAW files on import

I have never used RAW files before yesterday. About to shoot a wedding in a couple days so desperately need a fix or at least some advice for a workaround.
Here's my hardware list:
Canon 7D
SanDisk Ultra II 2 & 4 GB CF cards
Windows 7 64x
Internal card reader, not some flimsy USB thing
Lightroom 3
Problem:
After importing .CR2 RAW files using Lightroom 3, not Bridge, I found that some (not all) of the images appear to be corrupted. On the camera they look fine.
For a short moment, in Lightroom, they look fine, but then after clicking the thumbnail they instantly develop strange corruptions, like pink/yellow/opaque static.
This is not one of my photos, but the corrupted image looks just like this: http://thekuipers.org/images/IMG_2279.jpg
Used some advice and downloaded Fast Picture Viewer, which allows me to view the .CR2s in the folder I imported to, and MOST of them look fine now. Reimported to LR and now only like 8 of 200 images are corrupted. They still export to .jpg as corrupted.
I had formatted my CF cards immediately after importing, only to find the corruptions after. Using Stellar Phoenix Photo Recovery to try to reimport manually the residual data from CF cards. Will know if that works soon.

From previous posts on this forum there are several things that can cause this type of corruption on import; faulty, CF cards, card reader, cable, and RAM.
On my system it turned out to be faulty ram. Since changing my ram I have not experienced any further problems.

Preview of CR2 raw files on import window from camera

Hi
I have this problem with my Canon XTI. When I connect the camera to the computer and open the import dialog window, I can not see the previews of my CR2 raw files. But if I copy the CR2 files to he hard disk and try tho import from it, then previews are shown on the import window.
Can anybody help me?

Probably because the program is trying to write back a marker to the card as it "opens" the images for the preview and the camera won't let it.
It's not a good idea to import images directly from the camera anyway. Card readers are really cheap - and they WILL let you see the previews.

After Effects CS6: Canon .CR2 RAW files not recognized as acceptable files for import?

HI Folks,
I'm trying to import as I've seen on tutorials, my RAW files from my Canon 5D3 .CR2 files. I can open them in PS and LR5….and I'd seen examples of folks opening them with AE CS6 standalone, but it doesn't seem to recognize mine.
Any thoughts? Is there something I need to update, or flag or change?
I'm on a mac, OSX 10.7.5
AE verson: 11.0.4.2
This is what my import screen looks like:
Thanks in advance,
C

I read through those linked pages, but they didn't give me any solution.
After nosing around through a LOT of sites on Adobe's site (why aren't pages dated, took forever to find the most up to date or pertinent pages)…I found this one that was slightly related, but worked for me.
http://helpx.adobe.com/bridge/kb/acr-84-bridge-cs6-metadata.html
I had to download this zip, and manually place the plugin as directed, and now, After Effects CS6 will recognize my CR2 raw files from my canon 5D3.
Thank you for the help, it led me in the right direction, but the link above was the actual solution I found that worked!!
chilecayenne

Raw files won't import when shot in raw+jpg

I just shot in raw+jpg for the first time. Lightroom 4 won't import the raw file but will import the jpg. It says something like "lightroom doesn't support this raw file format". I don't get it though because if I shoot in just raw it will import fine.

If your camera is supported by current version of Lightroom, then the raw file(s) should import.
So, is Canon EOS Rebel XS 1000D supported by Lr4.3? If so, it should go (assuming you've got 4.3 installed), if no go, a bug report should be submitted, promptly, at:
http://feedback.photoshop.com/photoshop_family/topics/new
If not, consider a feature request ('Idea', for camera support) using same link.
Rob

Why Won't Lightroom 3.6 Import Camera raw files from T5i

I have Lightroom 3.6 all updated. I can't Import any raw files from my T5i
I have also tried using Adobe DNG but it will not read the files either.
Any Help would be Awesome
Thanks

You need LR 4.4 or DNGC 7.4 or newer for the T5i:
http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html
It is mislabeled as T51 on Adobe’s page.

I have photoshop CS 5.1. Just bought the fuji x100T and my RAW files won't work on it. What can I do?

I have just bought the fuji x100T and can't open the RAW files in CS 5.1. What can I do. Do I have to upgrade? Do I have to get the creative cloud? Do I get a discount to the creative cloud as I own a copy of CS 5.1? I hope someone can answer these questions. Many thanks.

You can either upgrade, as Warunicorn said, or use Adobe's free DNG converter to convert proprietary raws to the universal DNG raw format. Here are the links:
Adobe - Adobe Camera Raw and DNG Converter : For Windows : Adobe DNG Converter 8.7.1
Adobe - Adobe Camera Raw and DNG Converter : For Macintosh : Adobe DNG Converter 8.7.1
Benjamin

Corrupt CR2 RAW files

Has anyone found a fix for CR2 RAW files being corrupted? I have read all the thread postings I could google on various forums and can not seem to find any solid fix to the problem.
I purchased the Canon 400D for my trip to Asia and shot over 1500 photos, almost all in RAW. I transferred 90% of the images onto CDR and DVD media to make more room my Sandisk Extreme III 4gb card. Of the 1500+ photos, 150+ of my images remain corrupted.
I am posting this in hope that someone has found a fix.
Hardware:
Canon 400D Xti Rebel
Sandisk Extreme III 4gb
Atech Flash Technology "Pro-Gear" USB 2.0 card reader
IBM/Lenovo Z60M desktop replacement
Software:
Canon's DPP (Digital Photo Professional)
Microsoft Camera Raw Viewer (does not work with CR2)
Adobe CS2 with latest upgrades
I filled my CF card up four times during the duration of my trip.
Listed in order:
1 - 6 CDR's
2 - 1 DVD
3 - 3 CDR's
4 - straight transfer from CF card to my Z60m laptop
Of the four times I DL'ed images, the first 4 CDR's were the only folders that did not carry any corrupted files. All files were DL'ed onto a PC using my Atech card reader locally before burning.
Of all the images I took, I noticed a total of about 2 to 3 images that are shown to be corrupted when played back on my camera. I reviewed each and every file anywhere between 1 to 5 times on my camera prior to transfer and they all looked fine (maybe the camera plays back the embedded jpegs?). I would delete all images using the in camera function. I formatted the card before each fresh shoot. Originally thinking it was a CD/DVD transfer issue, that would not explain why some images from the last batch off the CF card (straight from CF card to reader to laptop) were also corrupted.
Here's my workflow (I'm new to RAW): I used Canon's DPP for a day and all the thumbnails displayed perfectly. Like CS2, I believe the software first displays the embedded jpg Thumbnails before loading the actual RAW preview. I did NOT notice any corrupted images based on the rendered thumbnails but I have not verified all my images first before making a strong claim to this.
I have not installed my copy of CS2 at this point and anxious to use Adobe Bridge, I did so the following day. After playing with some images, I began to notice some weird lost of colors in some of my thumbnail preview images. I attempted to open these files and DPP gave me a corrupt image notification. I tried it in Adobe Bridge and the images opened only to show me that either the image had part of it white, black or various colors. Some images were entirely black.
On the advice of a forum poster, I used Fastone Image viewer to see if I can save the image as jpegs and it worked but the jpeg was a smaller both in file size and dimension; not a complete lost at least. I did not recall having any image corruption with the exception of about 3 images (at most) which was witnessed on the camera itself during playback which prompted me to think that there was a bad sector on the CF card.
Notes:
- One forum poster suggested that Microsoft's RAW viewer were causing problems. Originally, I attempted to open one or two CR2 files and MS RAW viewer launched but gave me errors. I DL'ed the latest version and installed it and it will also not work on CR2's. After reading the MS page on the RAW viewer, it shows that CR2 was not supported yet. I then uninstalled the proggie after reading the posting.
- Another forum poster suggests that it is a bad card reader. I will attempt to transfer images directly from the camera going forward.
I'd hate to have this happen again but can not fathom why the problem will not reiterate itself with more RAW transfers going forward. Hopefully, someone has a good solution. Thanks. -Will

Rita,
The process for determining what is causing the files to be corrupt can be a tedious one depending on the following:
1. Can you review the images on your camera's LCD screen without problems? If not then the problem is most probably either a corrupted/faulty memory card or a faulty camera. If this is the case then your best bet at recovery (of sorts) is to use a program such as BrezzeBrowser from BreezeSys to extract the embedded jpeg versions of the corrupted RAW files from within each RAW file. Chances are, you won't manage to actually repair the corrupted RAW file but the jpegs are better than nothing.
2. If the images review ok on your camera but are corrupted when viewing on your computer and there seems to be no other problem with other files on your computer then it may be either a faulty card reader or usb/firewire cable between the card reader and the computer that is the culprit. Try the card reader with a different cable and also try a different card reader to determine the cause of the corruption.
3. If your symptoms are that you get different files corrupting over time when viewing them on your computer then the problem may be any one of either failing RAM memory, hard disk, hard disk controller or IDE/SATA hard disk cables. This is where the troubleshooting can be pretty tedious testing then eliminating each item from the list of suspicious pieces of hardware. Try the card and card reader on an altogether different computer to see if the files transfer correctly to that computer. If so then the problem lies with your computer hardware. If you haven't already done so at this stage, backup all your important data immediately (hopefully you keep backs anyway).
Hope this helps.

CR2 raw files

My wife swears blind that when she used to drag a Canon CR2 raw file from iPhoto 08 on to the desktop she used to get a .cr2 file on the desktop, whereas now she gets a jpeg. Is this right? Is there any way to get a raw file if dragged on to the desktop? I know that export will get a raw file on the desktop but she says that's the Windows way of doing things she just wants to drag it out as a raw.
Regards,
Steve

Steve:
Welcome to the Apple Discussions. Your wife is right but don't admit it. Just tried it with iPhoto 6 and the original CR2 file is created when dragged from the thumbnail to the desktop. I won't tell if you don't.
Suggest that feature at http://www.apple.com/feedback/iphoto.html.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've created an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 08 libraries. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Latest Lithroom 5.6 does not recognize my .cr2 raw file format and Windows 7 it asociates with my older raw plug in in Ps CS5.5. I am not able to change default program for .cr2 in the properties pannel...

Latest Lithroom 5.6 does not recognize my .cr2 raw file format and Windows 7 it asociates with my older raw plug in in Ps CS5.5. I am not able to change default program for .cr2 in the properties pannel...
every new released update of Lr from v 5.2 changed somethin in my Windows 7 Professional settings. I am stucked. Can somebody help me please? Many thanks. Andrej

Hi Jim,
yes after I imported my .cr2 raw files into new catalog it started to work. Windows 7 still does not recognize them but I can edit them as you said within the Lr5.6 and then export them into .psd or .dng files...as needed.
I bought Lr5 only because I got present - my new camera Cannon 70D and because my older Photoshop CS5.5 raw plugin does not recognize. cr2 files.
Many thanks for your help.
Andrej.

Why can't I download Canon S100 CR2 RAW files into PSE 10?

I am using PSE 10 with a Canon S100 camera. I am successful in downloading all of my jpeg files and RAW CR2 files from my older Canon Rebel, but not with the Canon S100 CR2 Raw files.
When first downloading from the Canon S100 camera into PSE 10 and later doing them manually, I receive the following messages: Nothing imported...files are not supported file types or alread in catalog. File damaged or in a format that cannot be included in the Elements Organizer.
These problems files, by the way, were automatically added to my Window's My Pictures catalog and are perfectly fine.

Thank you for the info. It worked great, once I was
able to get around a second problem that prevented updating
from within the PSE 10 application (error U41M1C212). That
problem was solved by disabling the MS Virtual WiFi Miniport
Adapter (located in the Network and Sharing Center control
panel). It just goes to show me once again, how complex
computer apps are and how much we all have to rely on each
other to get anything to work properly (frustratingly
enough, since the companies we paid good money to for
their problematic software are not very helpful). Thanks
again.
            Re: Why can't I download Canon S100 CR2 RAW files into
PSE 10?
            created by 99jon in Photoshop Elements - View the full discussion
Try opening a CR2 directly from a folder by right-clicking
and choosing open with Photoshop Elements editor, if that
dosent work, update the appliactaion (required for the
S100V)
In the Editor menu click Help >> Updates
Then install amera raw 6.7
            Replies to this
message go to everyone subscribed to this thread, not directly
to the person who posted the message. To post a reply, either
reply to this email or visit the message page:
http://forums.adobe.com/message/4602882#4602882
            To unsubscribe from
this thread, please visit the message page at
http://forums.adobe.com/message/4602882#4602882. In the
Actions box on the right, click the Stop Email
Notifications link.
            Start a new discussion
in Photoshop Elements by email or at Adobe Forums
            For more information
about maintaining your forum email notifications please go to
http://forums.adobe.com/message/2936746#2936746.

Importing cr2 raw files won't work on ios 6 when it worked fine on ios5. Anyone have a solution?

Similar Messages

Maybe you are looking for