Impossible to set Security Mode in router configuration

Instantly reverts to "Disabled", at every selection of any option in list.
Upgraded firmware; no change.
WRT54G ver 5.

Thanks for the replies.
Returning the favor:
Through experimentation (read: hide and seek, or let's waste time for fun),
I found in another page elsewhere in the configuration interface,
a cuteness called "Secure Easy Setup", at bottom of list,
whose enablement was required to banish the symptom.
Certainly interface designers, in their civilian lives, use the same programs that everybody uses. You'd think that, forced to suffer this kind of illogic everywhere, as we all are,
they would unfoul their own nests.

Similar Messages

7921G Security mode showing encrypted not sure why?

Hello Experts,
I am seeing the Secuity mode as Encrypted under system configuration of the 7921G phone.
I have done same configuration on the other phone and there I see the Security mode as NON-SECURE.
Config on both the ip phone: WLAN-Security mode- open under network profile..
Could someone please let me know why is it I am seeing as Encrypted security mode under system configuration?
Thanks
Fari

That is referring secure profiles in CUCM and not WLAN encryption.
Compare the CUCM configs.
You will see one is set for a secure profile and the other for a non-secure profile.
Sent from Cisco Technical Support iPhone App

Unlocking security mode on wireless router

I'm trying to unlock the security mode on the wireless router because I'm having a hard time adding a laptop to my wireless setting. Can anyone help?

well in this case you need to logon to the router's setup page...just let me know the model and version no. of the router that you are using...will tell you step by step troubleshooting steps...

Bytecode: Security mode set to "TrustSigned"

hi guys i have the next problem set hal in my daemon arrey restarted and i got the code after clamav
Bytecode: Security mode set to "TrustSigned"
now i can't go anywhere it looks like when it starts to load gdm it's just hanging there it won't even load it
i tried removing clamav from my daemons and setting it like this !clamav but it won't work
can you help me here
if you are gonna ask me why i set hal in my daemon arrey,i'm kinda like a noob my bluetooth adapter doesn't work so i thought by adding hal it might work

i already removed it from the daemon arrey and it's the same,i also tried removing clamav and ti's the same

How do you set up a wireless router for laptops only?

Recently I purchased the Lynksys WRT54G2 router for my home. My wife and I both have laptops and NO desktop computer. How do I hook up the router to work on both our laptops since we dont have a desktop computer? Thanks.

Connect one of your Laptop's to the router and configure your router...Once your router is configured you can run both the computers wireless...To configure the router :
If your ISP is Cable follow the link here...
If your ISP is DSL follow the link here ,
this will configure your router for Internet access, now change the wireless settings on your router...
Click on the Wireless tab on the Setup page- Here Wireless Network mode
should be mixed- Provide any non linksys network name ....
Name (SSID) box- Set wireless channel to 11- And wireless SSID
broadcast should be Enabled and then click on "Save Settings" >>Now
Click on the Sub tab under wireless > "Wireless Security"
Change the Wireless security mode to "WEP"...and put a 10 have a note of the key ...
click save settings ...
Click on Advanced Wireless settings>>
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" ...
Try to look for the Wireless Network on both the laptops and connect...

DSL w/831 router configuration questions

Hi all -
- DSL service with 1 static IP address
- DSL modem configured for "bridge mode"
- 831 router
There are some things I don't understand about all this.
#1: In order to make all this work, I need to have the PPPoE stuff configured on the router, yes?
#2: Do I need to have the "interface Dialer1" configured? And if not, can I put the DSL login info in the "interface Ethernet1" section?
#3: Do I need to explicitly set up NAT? I want my internal clients to get IPs on the 10.10.10.0 network and they need to have full Internet access.
#4: I think I don't understand how the routing should be set up.
#5: Any other helpful hints, I'll gladly take!!
Here's my config:
!This is the running config of the router: 10.10.10.1
!version 12.3
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging buffered 52000 debugging
enable secret xxxx
username user password xxxx
no aaa new-model
ip subnet-zero
ip dhcp excluded-address 10.10.10.1
ip dhcp pool CLIENT
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 205.152.xx.xx 205.152.xx.xx
lease 0 2
no ip domain lookup
ip audit notify log
ip audit po max-events 100
ip ssh break-string
no ftp-server write-enable
no scripting tcl init
no scripting tcl encdir
no crypto isakmp enable
interface Ethernet0
description Inside network$ETH-LAN$
ip address 10.10.10.1 255.255.255.0
ip nat inside
no cdp enable
hold-queue 32 in
interface Ethernet1
description Outside network, DSL connection
ip address 72.151.yy.yy 255.255.255.0
ip nat outside
duplex auto
pppoe enable
pppoe-client dial-pool-number 1
no cdp enable
interface FastEthernet1
no ip address
duplex auto
speed auto
interface FastEthernet2
no ip address
duplex auto
speed auto
interface FastEthernet3
no ip address
duplex auto
speed auto
interface FastEthernet4
no ip address
duplex auto
speed auto
interface Dialer1
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp pap sent-username [email protected] password xxxx
ip nat inside source list 102 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Ethernet1 permanent
ip http server
no ip http secure-server
access-list 23 permit 10.10.10.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
control-plane
line con 0
exec-timeout 120 0
no modem enable
transport preferred all
transport output all
stopbits 1
line aux 0
transport preferred all
transport output all
line vty 0 4
access-class 23 in
exec-timeout 120 0
login local
length 0
transport preferred all
transport input all
transport output all
scheduler max-task-time 5000
end

I've mostly the same config, but eth1 with no ip address and modem NOT in bridge mode! Try this ...

Failed to set security on SQL Server registry key. Error: 2

Hi,
I have a Primary site (mixed mode) running SCCM 2007 SP1 for many months now with no issues.
This site is made up of two Win 2008 sp2 servers sharing the SCCM roles:-
SCCM01 - Site server, DP, RP, PXE and SQL2005 hosting the SCCM database
SCCM02 – SUP, MP, FSP, SLP
The SQL2005 on SCCM01 is running under a domain service account called
domain\service_sccm which is also a sysadmin in SQL as is the SCCM02 server.
In an effort to resolve the isse I have made this account a Domain Admin.
I have also used this account to log onto SEC01 to run the Secondary Site installation and to be the SQL Service account.
I'm now trying to add a Secondary Site on a Domain Controller called SEC01 (also Win2008 sp2) and on the same LAN as the SCCM01/02.
This is where I get problems.
I run the installation locally on the Sec Site server (DC) as a Domain Admin and the installation completes OK (all green ticks),
the ComponentSetup.log and Pre-Reqs are all good as well however when I check the ConfigMgrSetup.log I see the below -
Failed to set security on SQL Server registry key. Error: 2.
<11-09-2010 22:46:59> SMS Setup full version is 4.00.6221.1000
<11-09-2010 22:46:59> Successfully set security on Setup registry key.
<11-09-2010 22:46:59> Failed to set security on SQL Server registry key. Error: 2
<11-09-2010 22:46:59> Successfully set security on Identification registry key.
<11-09-2010 22:46:59> Creating SMS Inbox Source registry key ...
<11-09-2010 22:46:59> Installing SMS Site Component Manager ...
<11-09-2010 22:46:59> Installing Site Component Manager under acct <NT AUTHORITY\SYSTEM> path <C:\Program Files (x86)\Microsoft
Configuration Manager\bin\i386\sitecomp.exe>
<11-09-2010 22:47:01> Started Site Component Manager service
<11-09-2010 22:47:01> SMS Site Component Manager installation completed.
<11-09-2010 22:47:01> Done with service installation
Adding the PMP role to SEC01 also fails to install and no MPSetup or MPControl logs are created.
WebDav and win2008 roles, features all added and server fully patched.
Despooler.log on SCCM01 seems good and passing keys.
Tried installing to default path and to shortened path such as C:\SCCM
The new secondary site is listed in the console and an address can be added for the Secondary Site
BITS Server Extensions and Remote Differential Compression Features are enabled.
The Group memberships all appear ok:-
SCCM01
Local Admins
contains the sec site server SEC01, SCCM01, installation accounts
SMS_SiteToSiteConnection_001
SEC01 (the sec site server)
SMS_SiteSystemToSiteServerConnection_001
SCCM02
SEC01
No Local Admins as a DC
SMS_SiteToSiteConnection_002
SCCM01
SMS_SiteSystemToSiteServerConnection_002
empty
SQL 2005
This has the account logged in during installation as a sysadmin
SCCM02 is also sysadmin
The fundamental issue appears to be that the SEC01$ server account is not being added to SQL Logins (and therefore SCCM database Roles)
therefore the installation cannot complete.
I have tried to manually add the SEC01 account to SQL Logins before installation of Sec Site but this did not work.
Not sure if the fact that SEC01 is a DC may be a factor.
Appreciate any help if anyone has seen this before or can suggest a resolution.
Thanks

After a lot of digging around and head scratching I eventually found the resolution.
The original thread title Error turned out to be a bit of a red herring in that my failure to deploy Sec Sites came down to two separate issues seemingly unrelated to the error message of the thread title.
The first part of the resolution was to manually create the SQL Server accounts for the Sec Site Servers and assign them to the smsdbrole_MP DB role to
let the SQL side of the SCCM install complete a s these were not being created automatically.
This then left the fact that that the installation of the Sec Site completed successfully according to the install logs in C:\ however the DP and MP would
never install.
The big clue was eventually contained in the mpfdm.log errors relating to
**ERROR: Cannot find path for destination inbox SMS_AMT_PROXY_COMPONENT on server REGISTRY SMS_MP_FILE_DISPATCH_MANAGER
and
**ERROR: Cannot find path for destination inbox Asset Intelligence KB Manager on server REGISTRY SMS_MP_FILE_DISPATCH_MANAGER
Thankfully the errors led me to these two blogs:
http://myitforum.com/cs2/blogs/scassells/archive/2009/07/20/error-cannot-find-path-for-destination-inbox-sms-amt-proxy-component-on-server-registry.aspx
and
http://social.technet.microsoft.com/Forums/en-US/configmgrsetup/thread/5fcc53d4-8629-4b34-9eaa-6cb020eedc13/
As it turned out the SCCM installation registry and folder creation does not complete and I had to manually enter the reg settings as detailed in the
links above to complete the installation. Once I did as described everything worked a treat – all my MPs and DPs are 100% now.
Solutions
Add the following reg keys to each of your effected secondary sites.
Inbox Fix
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\MPFDM\Inboxes]
"Asset Intelligence KB Manager"="E:\\Program Files\\Microsoft Configuration Manager\\inboxes\\AIKbMgr.box"
"SMS_AMT_PROXY_COMPONENT"="E:\\Program Files\\Microsoft Configuration Manager\\inboxes\\amtproxy.box"
Asset Intelligence fix:
Note: you will need to identify the next largest key value.
In my example it was key 49
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\Inbox Source\Inbox Definitions\49]
"Inbox Name"="Asset Intelligence KB Manager"
"Relative Path"="inboxes\\AIKbMgr.box"
"NAL Path"=""
"User Rights"=dword:00000000
"Service Rights"=dword:00000004
"Monitoring Enabled"=dword:00000001
"Location Type"=dword:00000001
"Guest Rights"=dword:00000001
AMT registry Fix.
  Note: you will need to identify the next largest key value.
In my example it was key 50
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\Inbox Source\Inbox Definitions\50]
"Inbox Name"="SMS_AMT_PROXY_COMPONENT"
"Relative Path"="inboxes\\amtproxy.box"
"NAL Path"=""
"User Rights"=dword:00000000
"Service Rights"=dword:00000004
"Monitoring Enabled"=dword:00000001
"Location Type"=dword:00000001
"Guest Rights"=dword:00000001
Big thanks to Shaun Cassells and John Marcum for these blogs

Cant get Security Mode to work on WRT54G

I have everything set up fine.. internet working etc but I cannot get security mode to work.. I go to click on WEP, WPA.. whatever and it just autos back to DISABLED.. Anyone to fix this?

how many computers do you have?
try to use other computers in setting up the security. check also the firmware of your router.make sure you have the latest one.

Database control won't run in secure mode

I'm following the instructions displayed by the database configuration manager after creating a database. These instructions configure the database control to run in secure mode using https. I get an error with the following command run from the OS command line while in the ORACLE_HOME/bin directory:
emctl.bat secure dbconsole -sysman_pwd password
I get the error message "Failed to create EM root key."
The emdctl.trc file has the following entry: "No connection could be made because the target machine actively refused it."
The ORACLE_SID has already been set. The database control is down. The "emctl config emkey -repos" command completed successfully.
I'm using Oracle 10.2.0.4 on Windows 2003 server. I'm running this command on the database server. The database control was selected in the database configuration manager. This database control does run successfully in http mode, but I can't configure it for https.
Does anyone know why the target machine would actively refuse this connection?

Have you tried it without the -sysman_pwd flag ?
MOS Doc 276950.1 - How to setup Enterprise Manager Database Control for SSL (HTTPS) secure connection
HTH
Srini

Basic Internet Routing Configuration Help -- Cisco 2811

Hi everyone,
I want to start by saying that I brought a Cisco 2811 Router to use at home and to practice advanced networking with. So far, I believe I've configured everything as it should be, however, I am not getting any internet connection.
DHCP is set up and working properly, I can lease addresses without issue.
Both interfaces are configured, fe0/1 with a static IP, and fe0/0 as a DHCP client.
I have connected fe0/0 directly to the Cable modem and it acquires an IP without issue. Connecting my laptop directly into fe0/1 allows my laptop to lease an IP from the router's DHCP server. So I know everything up to there is working properly. I've set up NAT as best I can with what I know, but I am still not getting the router to provide internet access.
The following is my Router's Configuration. Does anything seem to be missing? I used Configuration Professional to set it up.
------------Begin Configuration-------------
Building configuration...
Current configuration : 2570 bytes
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Network
boot-start-marker
boot-end-marker
security authentication failure rate 10 log
security passwords min-length 6
no logging buffered
logging console critical
enable secret 5 $1$4FJS$RQUEiWuTaMOAGhVx1O1Du0
enable password 7 046F03070C291D175F40
aaa new-model
aaa authentication login local_auth local
aaa session-id common
dot11 syslog
no ip source-route
no ip routing
no ip gratuitous-arps
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1
ip dhcp pool Network
import all
network 192.168.100.0 255.255.255.0
dns-server 4.2.2.2 4.2.2.1
lease 7
no ip bootp server
ip domain name Network
ip name-server 4.2.2.2
ip name-server 4.2.2.1
login block-for 5 attempts 5 within 1
multilink bundle-name authenticated
voice-card 0
no dspfarm
username Admin password 7 1526035D5D7C72252B3B
archive
log config
hidekeys
interface FastEthernet0/0
description $ETH-WAN$
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex full
speed auto
no mop enabled
interface FastEthernet0/1
ip address 192.168.100.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex full
speed auto
no mop enabled
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat pool Network 192.168.100.1 192.168.100.254 netmask 255.255.255.0
ip nat inside source list 101 interface FastEthernet0/0 overload
logging trap debugging
logging facility local2
access-list 100 permit udp any any eq bootpc
access-list 101 remark INTERNET ACCESS THROUGH NAT
access-list 101 remark CCP_ACL Category=2
access-list 101 permit ip 192.168.100.0 0.0.0.255 any
dialer-list 1 protocol ip permit
snmp-server community public RO
no cdp run
control-plane
banner motd ^C Welcome! ^C
line con 0
login authentication local_auth
transport output telnet
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
line vty 0 4
password 7 107D0C1A10051B1F15
login authentication local_auth
transport input telnet
scheduler allocate 20000 1000
end
------------------End Configuration-------------------
Does anything seem amiss? Thank you all in advance for your help!
John

Hi Again,
I sent
dhcp pool Network
default-router 192.168.100.1
to the router and wrote it to config. I still didn't have internet access at first, so I followed John's tip and hooked up my machine to an old Catalyst 2849G switch I had laying around. The switch has no settings, just gets an ip from the router and does its own thing. After doing so, I do now have internet access. I'm using it to post this reply in fact.
Here are the results of ipconfig /all on my Ethernet NIC on my machine before even having the switch:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : hsd1.ut.comcast.net.
Description . . . . . . . . . . . : Intel(R) Ethernet Connection I217-LM
Physical Address. . . . . . . . . : 54-EE-75-27-6F-06
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::7cdd:83b5:e603:127e%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.100.2(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, October 02, 2014 7:57:10 AM
Lease Expires . . . . . . . . . . : Thursday, October 09, 2014 7:57:10 AM
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 192.168.100.1
DHCPv6 IAID . . . . . . . . . . . : 290778741
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1B-B2-3D-AF-54-EE-75-27-6F-06
DNS Servers . . . . . . . . . . . : 75.75.76.76
75.75.75.75
NetBIOS over Tcpip. . . . . . . . : Enabled
It seems everything was working as it should, but I didn't have internet access and windows still reported it as an unknown network.
After hooking up my Switch, Windows reported seeing 'Network' (From my router's host name, I presume?) and once I reset the modem, I had internet access.
This was a huge learning experience and I am glad to have help from all of you. Is there anything else I can to do optimize my configurations? Also, why didn't I have internet access when directed hooked up to FastEthernet0/1 even though my machine acquired IP's and DNS info?
Here is another copy of the running config with today's changes:
---------------------Begin Configuration------------------------
Building configuration...
Current configuration : 2401 bytes
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Network
boot-start-marker
boot-end-marker
security authentication failure rate 10 log
security passwords min-length 6
logging buffered 4096
logging console critical
enable secret 5 $1$4FJS$RQUEiWuTaMOAGhVx1O1Du0
enable password 7 046F03070C291D175F40
aaa new-model
aaa authentication login local_auth local
aaa session-id common
dot11 syslog
no ip source-route
no ip gratuitous-arps
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1
ip dhcp pool Network
import all
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
lease 7
no ip bootp server
ip domain name Network
login block-for 5 attempts 5 within 1
multilink bundle-name authenticated
voice-card 0
no dspfarm
username Admin password 7 1526035D5D7C72252B3B
archive
log config
hidekeys
interface FastEthernet0/0
description $ETH-WAN$
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
duplex full
speed auto
no mop enabled
interface FastEthernet0/1
ip address 192.168.100.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
duplex full
speed auto
no mop enabled
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 dhcp
ip http server
no ip http secure-server
ip nat pool Network 192.168.100.1 192.168.100.254 netmask 255.255.255.0
ip nat inside source list 10 interface FastEthernet0/0 overload
logging trap debugging
logging facility local2
access-list 10 permit 192.168.100.0 0.0.0.255
access-list 100 permit udp any any eq bootpc
dialer-list 1 protocol ip permit
snmp-server community public RO
no cdp run
control-plane
banner motd ^C Welcome! ^C
line con 0
login authentication local_auth
transport output telnet
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
line vty 0 4
password 7 107D0C1A10051B1F15
login authentication local_auth
transport input telnet
scheduler allocate 20000 1000
end
--------------------------End Configuration-------------------------
Let me know if there is anything else you guys need or I should do, I'll be back after classes today. Thanks again!
-John

Wlan security mode

i understood that the reason for unabling to find my home router is that its secured(not sure). im trying to switch between wep/802.1x/wpa/wpa2 but im losing my self in the subdefinitions. what set of definitions might work?

petrib
I've read from my phones manual "to enable at least one security mode". When I open secutity settings for WLAN, WEP, WPA, VPN & IEEE802 appears. What security mode shall I use if I connect to a Hotspot that is in public places?

Security Mode option: "Capture (wlansec. wpapersharekey) WPA Personal" ?

Hi, I'm trying to support my father remotely and was reviewing his security setup over the phone, making sure everything was still okay. He has the wrt54g (I think v5 and I don't know the firmware version) - and in Wireless> Wireless Security> Security Mode he has "Capture(wlansec.wpapersharekey)WPA Personal" selected. When I set this up 6 months ago, I don't recall if I selected that and thought the docs were misprinted - or what.
I didn't bother to have my father tell me what the other choices were as I was perplexed and thought that since it says "WPA Personal" everything is normal (and since wireless connectivity works, it seems he is, in fact, using WPA). But is this setting normal? I cannnot find out any information about this setting in the docs, on this forum, google, etc. Even linksys phone support did not know. All documentation says to select "WPA Personal". Is this the same thing? Is what I'm seeing a setting in the older firmware maybe? Note - we have not upgraded firmware since the router was bought 6 months ago (lazyness).
The client is a mac.
Thanks
Nancy C.
(Mod note: Edited subject line to keep threads from stretching. Thanks!)Message Edited by JOHNDOE_06 on 10-25-2006 03:23 PM

it is really normal for your router's interface to display that script of "Capture(wlansec.wpapersharekey)WPA Personal" when you are viewing that on a MAC computer.. but on the windows (xp, 2k, ME, 98, 95, etc), it'll disaplay the normal script...
"a helping hand in a community makes the world a universe"

Essbase native security mode and MSAD users

Hi guys,
I'm trying to solve following question:
I need to keep Essbase in native security mode, ie. to assign security for users directly in EAS, not in HSS console. And I need to grant access to MSAD users, ie. to allow users to connect to Essbase using their MSAD usernames and passwords.
How to do that?
Thanks!
Vladino

You don't state what release you're on -- I think it varies slightly from release to release although the concept is mostly the same.
Have you read this in the EAS help?
http://download.oracle.com/docs/cd/E17236_01/epm.1112/eas_help/extauthen.html
I think this help is missing the step where you tell Essbase what the external authenticators are. From reading about the AUTHENTICATIONMODULE Essbase.cfg setting:
http://download.oracle.com/docs/cd/E17236_01/epm.1112/esb_tech_ref/authenticationmodule.html
It seems that:
When you run Oracle's Hyperion Enterprise Performance Management System Configurator, Essbase is automatically registered with Shared Services (unless you select the option to deploy Essbase in standalone mode) and this setting is automatically added to essbase.cfg.So I'm not quite sure where that leaves you -- where do you config the external authentication? Hopefully someone more installation-centric than I (which would be just about everyone in the known universe) can jump in here. I have to say that I haven't used non-Shared Services authentication since System 9 came out -- it just makes life too easy for my clients to manage security in one place.
Regards,
Cameron Lackpour

Cannot Security Enable BEFW11S4 Router

I was given a cable modem and a router (BEFW11S4 vers 4) when I moved, as I was going to get cable wireless internet in my new place. I was able to set up the internet access with the cable modem and can set up wireless with the router as long as it's not security enabled. I can name the network, but as soon as I try to WEP encrypt (64 bit), I get kicked off of the connection and when I try to reconnect, I get a message that the network requires settings not present on my computer. I've had to reset the router about 4 times in 2 hours just to get wireless service in my apartment, but I would really like to have it secured. I called customer support, but was told that since the warranty expired on the router I'd have to pay to have them help me, so I'd like to try to fix this on my own if I can. I am currently able to send this because I am directly connected to my cable modem. I've tried to use the CD that came with the router to configure the router to the PC, but when I get to the part where you have to connect the PC to the router, it says that the router can't be found, and to make sure it's on or reset it. My computer uses Microsoft Vista operating system. Does anyone know how to handle something like this, or where to find instructions on how to handle it? Thanks

I think the first thing which you need to do is upgrade the firmware of your router. i think its a problem with the firmware of your Router. Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop...
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Once you re-configure all the settings on your Router then you can enable the security on your Router. I think this might solve the problem.

Can I set up a second router (extreme or express) with WEP while keeping 802B,G,N on the primary router (TC)

I have a wireless temperature controller which only uses WEP security. I have my TC configured for 802.11 B,G,N which disables WEP. Can I extend or create a new wireless network which uses WEP while maintaining my current network configuration?

Yes, this is extremely easy..
Get a wireless router or AP.. anything cheap will usually be fine.. you don't need fancy. And if it is G or B wireless then a second hand is also fine.
For a wireless router you can bridge it, if that option is available.. usually not.
So you do a sneaky work around called wan bypass.
It is easier to give you actual situation.
TC running standard IP 10.0.1.1
Set up the WEP router with IP, 10.0.1.254 (puts it outside the range of dhcp in the TC and will never be used).
Turn off the dhcp server.
I do suggest you set a fixed wireless channel,, so it doesn't interfere with the TC.
eg 1, for 2.4ghz.
Then plug LAN port of the router to the LAN port of the TC by ethernet.
Voila, you have a secondary AP and can set poor security on it.
*** DANGER DANGER WILL ROBINSON***
You have just reduced the security of your whole network by creating a loophole.
I would strongly recommend turn it off when you finished playing on your Wii or whatever ancient device that uses WEP.

Impossible to set Security Mode in router configuration

Similar Messages

Maybe you are looking for