Improve perforamce of SA540 site to site VPN

Site A SA540 : 50M/50M DSL (Country A) (15 users)
Site B SA540 : 2M/520KB ADSL (Country B) (10 users)
MTU: 1464 (Test on ping frame)
We has custom application server and work on  services port 80, this is old application and need to call up dos prompt java.
We make server on Site A and alos setup up port forward from WAN to custome application server.
I find out at Site B direct use http services over the WAN just need around 5-10 seconds to launch the applaciton
On the same machine, we use site to site VPN to connection the application, that will need around 15 ~ 20 seconds or more, alos sometime can not load success the application through VPN, how can I improve it? Or any suggestion I need to pay attend?
Thanks        

Chammy,
I'll echo Tom's comment.  One thing to keep in consideration is that buidling up the VPN tunnel adds overhead to the traffic flow so a slower response over a VPN compared to open access is to be expected and will be more noticable on slower links.
Shawn Eftink
CCNA/CCDA
Please rate all helpful posts and mark correct answers to assist others searching for solutions in the community.

Similar Messages

  • SA540 Site-to-Site VPN

    Hi everyone!
    I'll be doing a Site-to-site VPN setup on one of my client.
    I just want to know any head's up or if there are any issues with the use of an SA540 on a site-to-site setup?
    Thanks!

    No issues that I know of. Just follow the instructions on page 137 of the Admin guide.
    Let us know how it goes.

  • Question about site to site VPN failover on an ASA

    Hello all. I am building a site to site VPN from our headquarters to a customer. I am using an ASA 5520. The customer is using Cisco 3945 routers. The customer has two VPN termination points. The customer requests that we make one of their termination points the primary VPN connection and make the other termination point the backup in the event that the primary VPN fails. How do I configure this on the ASA? Does the below configuration fulfill this goal?
    crypto map cccccc 10 set peer 2.2.2.2 1.3.3.3

    I have just encountered a similar situation.  It seems to work near enough, but I still consider it a hack.  
    Also if the second peer (887 router in this case) attempts to bring up the IPSec tunnel the ASA drops the the primary tunnel and restablishes it causing brief packet loss during the tunnel bounce.  A debug shows an error that it thinks the peer IP has changed, hence the tunnel should be dropped!!!
    Im just using HRSP on the access site between 2 x 887's tracking the WAN interface.  On the ASA side I have both peers defined in the same way "crypto map cccccc 10 set peer 2.2.2.2 1.3.3.3".
    The ASA feature set just hasnt improved in this space since the VPN3000 days, it may have actually gone backwards. Introduction of VTI interfaces and support for routing protocols over tunnels should have been introduced into the ASA years ago, but from what I understand has been put in the too hard basket.
    Cheers
    Kent.

  • TWO Site to Site VPN connections at the same locations

    Hi:
    We have two locations (Site A & Site B) and currently have a site to site vpn stood up that we allow both data and voice traffic to flow across.  However, we have been having MAJOR issues with our voice quality and no luck with improvement using QoS settings, etc.  Therefore, we would like to stand up another site to site connection to have only voice traffic to flow over and haven't been able to do so because at each side we only have a single block of IP's (/29) and it is my understanding that it isn't possible to have two separate VPN tunnels as I am describing when the subnet is the same, is that correct?
    Moving forward, we are looking into adding a 2nd block of addresses to both sides, however, Comcast Business is telling us that it isn't possible with their service :(.
    Does anyone have other options for me besides moving to a different ISP?
    Thank you,
    Stangride

    This is a standard facet of most VPNs - the problem lies in your NAT router since both clients appear to come from the same IP address as far as the VPN server is concerned, and the router can't separate out the traffic.
    There are a couple of solutions.
    First, the built-in VPN server supports L2TP and PPTP protocols. You should be able to connect one system under each protocol, so that gets your two machines connected.
    Second, you can replace your NAT router with one that supports multiple VPN clients (often termed 'VPN passthrough').
    Third, setup a site-to-site tunnel so that your entire LAN is connected to the VPN (this saves you from having to run a separate VPN client on each machine, but is typically only worth it when you have more machines).

  • Optimize site-to-site VPN performance

    Dear all.
    I have a site-to-site VPN across the internet forming a WAN connection (1 Mbps) between two sites. On one end I have Pix 515 firewall and on the other end I have an ASA 5505. Is there any form of data compression that can be enabled on the PIX and the ASA in order to improve performance across the VPN connection?
    Regards,
    Screech

    i would suggest u instead of looking toward compression
    u could use bandwidth managment methods in ASA and PIX that help prioritize some traffic over other in this way u can garntee the important traffic and improve the link
    have alook at the following link:
    http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a008084de0c.shtml
    good luck
    if helpful Rate

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • Cisco ASA 5505 Site to Site VPN

    Hello All,
    First time posting to the forums. I've been working with Cisco ASA 5505 for a number of months and recently I purchased a 2nd ASA with the goal of setting up Site to Site VPN tunnel. It look so simple from the number of videos that I have watched on the internet. But when I have done it suprise suprise it didn't work for me ... I have deleted the tunnels a number of times and attempted to recreate them. I am using the VPN wizard in the ADM to create the tunnel. Both the asa are 5505 and have the same same firmware etc.
    I would appreciate any help that can be directed towards this issue please.  Slowly losing my mind
    Please see details below:
    Both ADM are 7.1
    IOS
    ASA 1
    aved
    ASA Version 9.0(1)
    hostname PAYBACK
    enable password HSMurh79NVmatjY0 encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description Trunk link to SW1
    switchport trunk allowed vlan 1,10,20,30,40
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    no nameif
    no security-level
    no ip address
    interface Vlan2
    nameif outside
    security-level 0
    ip address 92.51.193.158 255.255.255.252
    interface Vlan10
    nameif inside
    security-level 100
    ip address 192.168.10.1 255.255.255.0
    interface Vlan20
    nameif servers
    security-level 100
    ip address 192.168.20.1 255.255.255.0
    interface Vlan30
    nameif printers
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    interface Vlan40
    nameif wireless
    security-level 100
    ip address 192.168.40.1 255.255.255.0
    banner login line Welcome to Payback Loyalty Systems
    boot system disk0:/asa901-k8.bin
    ftp mode passive
    clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns domain-lookup servers
    dns domain-lookup printers
    dns domain-lookup wireless
    dns server-group DefaultDNS
    name-server 83.147.160.2
    name-server 83.147.160.130
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network ftp_server
    object network Internal_Report_Server
    host 192.168.20.21
    description Automated Report Server Internal Address
    object network Report_Server
    host 89.234.126.9
    description Automated Report Server
    object service RDP
    service tcp destination eq 3389
    description RDP to Server
    object network Host_QA_Server
    host 89.234.126.10
    description QA Host External Address
    object network Internal_Host_QA
    host 192.168.20.22
    description Host of VM machine for QA
    object network Internal_QA_Web_Server
    host 192.168.20.23
    description Web Server in QA environment
    object network Web_Server_QA_VM
    host 89.234.126.11
    description Web server in QA environment
    object service SQL_Server
    service tcp destination eq 1433
    object network Demo_Server
    host 89.234.126.12
    description Server set up to Demo Product
    object network Internal_Demo_Server
    host 192.168.20.24
    description Internal IP Address of Demo Server
    object network NETWORK_OBJ_192.168.20.0_24
    subnet 192.168.20.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_26
    subnet 192.168.50.0 255.255.255.192
    object network NETWORK_OBJ_192.168.0.0_16
    subnet 192.168.0.0 255.255.0.0
    object service MSSQL
    service tcp destination eq 1434
    description MSSQL port
    object network VPN-network
    subnet 192.168.50.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_24
    subnet 192.168.50.0 255.255.255.0
    object service TS
    service tcp destination eq 4400
    object service TS_Return
    service tcp source eq 4400
    object network External_QA_3
    host 89.234.126.13
    object network Internal_QA_3
    host 192.168.20.25
    object network Dev_WebServer
    host 192.168.20.27
    object network External_Dev_Web
    host 89.234.126.14
    object network CIX_Subnet
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network NETWORK_OBJ_84.39.233.50
    host 84.39.233.50
    object network NETWORK_OBJ_92.51.193.158
    host 92.51.193.158
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq ftp
    service-object tcp destination eq netbios-ssn
    service-object tcp destination eq smtp
    service-object object TS
    object-group network Payback_Internal
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_3
    service-object tcp destination eq www
    service-object tcp destination eq https
    service-object object TS
    service-object object TS_Return
    object-group service DM_INLINE_SERVICE_4
    service-object object RDP
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group service DM_INLINE_SERVICE_5
    service-object object MSSQL
    service-object object RDP
    service-object object TS
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group service DM_INLINE_SERVICE_6
    service-object object TS
    service-object object TS_Return
    service-object tcp destination eq www
    service-object tcp destination eq https
    access-list outside_access_in remark This rule is allowing from internet to interal server.
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark FTP
    access-list outside_access_in remark RDP
    access-list outside_access_in remark SMTP
    access-list outside_access_in remark Net Bios
    access-list outside_access_in remark SQL
    access-list outside_access_in remark TS - 4400
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
    access-list outside_access_in remark Access rule to internal host QA
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
    access-list outside_access_in remark Access to INternal Web Server:
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
    access-list outside_access_in remark Rule for allowing access to Demo server
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark RDP
    access-list outside_access_in remark MSSQL
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
    access-list outside_access_in remark Access for Development WebServer
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
    access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
    access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
    access-list AnyConnect_Client_Local_Print remark Windows' printing port
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
    access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
    access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
    access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
    access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
    access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
    access-list outside_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
    pager lines 24
    logging enable
    logging console informational
    logging asdm informational
    logging from-address
    [email protected]
    logging recipient-address
    [email protected]
    level alerts
    mtu outside 1500
    mtu inside 1500
    mtu servers 1500
    mtu printers 1500
    mtu wireless 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source dynamic any interface
    nat (wireless,outside) source dynamic any interface
    nat (servers,outside) source dynamic any interface
    nat (servers,outside) source static Internal_Report_Server Report_Server
    nat (servers,outside) source static Internal_Host_QA Host_QA_Server
    nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
    nat (servers,outside) source static Internal_Demo_Server Demo_Server
    nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Internal_QA_3 External_QA_3
    nat (servers,outside) source static Dev_WebServer External_Dev_Web
    nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.10.0 255.255.255.0 inside
    http 192.168.40.0 255.255.255.0 wireless
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 84.39.233.50
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside client-services port 443
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 77.75.100.208 255.255.255.240 outside
    ssh 192.168.10.0 255.255.255.0 inside
    ssh 192.168.40.0 255.255.255.0 wireless
    ssh timeout 5
    console timeout 0
    dhcpd dns 192.168.0.1
    dhcpd auto_config outside
    dhcpd address 192.168.10.21-192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    dhcpd option 15 ascii paybackloyalty.com interface inside
    dhcpd enable inside
    dhcpd address 192.168.40.21-192.168.40.240 wireless
    dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
    dhcpd update dns interface wireless
    dhcpd option 15 ascii paybackloyalty.com interface wireless
    dhcpd enable wireless
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy Payback_VPN internal
    group-policy Payback_VPN attributes
    vpn-simultaneous-logins 10
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Payback_VPN_splitTunnelAcl
    group-policy DfltGrpPolicy attributes
    dns-server value 83.147.160.2 83.147.160.130
    vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
    group-policy GroupPolicy_84.39.233.50 internal
    group-policy GroupPolicy_84.39.233.50 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username Noelle password XB/IpvYaATP.2QYm encrypted
    username Noelle attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
    username Eanna attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Michael password qpbleUqUEchRrgQX encrypted
    username Michael attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
    username Danny attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
    username Aileen attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
    username Aidan attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    username shane.c password iqGMoWOnfO6YKXbw encrypted
    username shane.c attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Shane password uYePLcrFadO9pBZx encrypted
    username Shane attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username James password TdYPv1pvld/hPM0d encrypted
    username James attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username mark password yruxpddqfyNb.qFn encrypted
    username mark attributes
    service-type admin
    username Mary password XND5FTEiyu1L1zFD encrypted
    username Mary attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
    username Massimo attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    tunnel-group Payback_VPN type remote-access
    tunnel-group Payback_VPN general-attributes
    address-pool VPN1
    default-group-policy Payback_VPN
    tunnel-group Payback_VPN ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 general-attributes
    default-group-policy GroupPolicy_84.39.233.50
    tunnel-group 84.39.233.50 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map global-class
    match default-inspection-traffic
    policy-map global-policy
    class global-class
      inspect dns
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect pptp
      inspect rsh
      inspect rtsp
      inspect sip
      inspect snmp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
      inspect icmp error
      inspect icmp
    service-policy global-policy global
    smtp-server 192.168.20.21
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1
    ASA 2
    ASA Version 9.0(1)
    hostname Payback-CIX
    enable password HSMurh79NVmatjY0 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description This port connects to VLAN 100
    switchport access vlan 100
    interface Ethernet0/2
    interface Ethernet0/3
    switchport access vlan 100
    interface Ethernet0/4
    switchport access vlan 100
    interface Ethernet0/5
    switchport access vlan 100
    interface Ethernet0/6
    switchport access vlan 100
    interface Ethernet0/7
    switchport access vlan 100
    interface Vlan2
    nameif outside
    security-level 0
    ip address 84.39.233.50 255.255.255.240
    interface Vlan100
    nameif inside
    security-level 100
    ip address 192.168.100.1 255.255.255.0
    banner login line Welcome to Payback Loyalty - CIX
    ftp mode passive
    clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns server-group defaultDNS
    name-server 8.8.8.8
    name-server 8.8.4.4
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network CIX-Host-1
    host 192.168.100.2
    description This is the host machine of the VM servers
    object network External_CIX-Host-1
    host 84.39.233.51
    description This is the external IP address of the host server for the VM server
    object service RDP
    service tcp source range 1 65535 destination eq 3389
    object network Payback_Office
    host 92.51.193.158
    object service MSQL
    service tcp destination eq 1433
    object network Development_OLTP
    host 192.168.100.10
    description VM for Eiresoft
    object network External_Development_OLTP
    host 84.39.233.52
    description This is the external IP address for the VM for Eiresoft
    object network Eiresoft
    host 146.66.160.70
    description DBA Contractor
    object network External_TMC_Web
    host 84.39.233.53
    description Public Address of TMC Webserver
    object network TMC_Webserver
    host 192.168.100.19
    description Internal Address of TMC Webserver
    object network External_TMC_OLTP
    host 84.39.233.54
    description Targets OLTP external IP
    object network TMC_OLTP
    host 192.168.100.18
    description Targets interal IP address
    object network External_OLTP_Failover
    host 84.39.233.55
    description Public IP of OLTP Failover
    object network OLTP_Failover
    host 192.168.100.60
    description Server for OLTP failover
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object network Wired
    subnet 192.168.10.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network Eiresoft_2nd
    host 137.117.217.29
    description Eiresoft 2nd IP
    object network Dev_Test_Webserver
    host 192.168.100.12
    description Dev Test Webserver Internal Address
    object network External_Dev_Test_Webserver
    host 84.39.233.56
    description This is the PB Dev Test Webserver
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_2
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_3
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_4
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_5
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_6
    service-object object MSQL
    service-object object RDP
    object-group network Payback_Intrernal
    network-object object Servers
    network-object object Wired
    network-object object Wireless
    object-group service DM_INLINE_SERVICE_7
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_8
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_9
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_10
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_11
    service-object object RDP
    service-object tcp destination eq ftp
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
    access-list outside_access_in remark Development OLTP from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
    access-list outside_access_in remark Access for Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
    access-list outside_access_in remark Access to OLTP for target from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
    access-list outside_access_in remark This is allowing access from Eiresoft to the OLTP Failover server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover
    access-list outside_access_in remark Access for the 2nd IP from Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
    access-list outside_access_in remark Access from the 2nd Eiresoft IP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
    access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 192.168.10.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source dynamic any interface
    nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
    nat (inside,outside) source static Development_OLTP External_Development_OLTP
    nat (inside,outside) source static TMC_Webserver External_TMC_Web
    nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
    nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
    nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 92.51.193.156 255.255.255.252 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 92.51.193.158
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 77.75.100.208 255.255.255.240 outside
    ssh 92.51.193.156 255.255.255.252 outside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy GroupPolicy_92.51.193.158 internal
    group-policy GroupPolicy_92.51.193.158 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 general-attributes
    default-group-policy GroupPolicy_92.51.193.158
    tunnel-group 92.51.193.158 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
    : end

    Hi,
    Thanks for the help to date
    I now have the Site to Site working but there is one little issue I have. If I try to RD to a server through the tunnel it will not allow connection on the first attempt however if I ping that host and then attempt to RD it will allow the connection. It looks like the host is asleep until it receives traffic through the tunnel. Is this thje correct behaviour.
    See below the details:
    ASA1:
    hostname PAYBACK
    enable password HSMurh79NVmatjY0 encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    ip local pool VPN1 192.168.50.1-192.168.50.254 mask 255.255.255.0
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description Trunk link to SW1
    switchport trunk allowed vlan 1,10,20,30,40
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    no nameif
    no security-level
    no ip address
    interface Vlan2
    nameif outside
    security-level 0
    ip address XX.XX.XX.XX 255.255.255.252
    interface Vlan10
    nameif inside
    security-level 100
    ip address 192.168.10.1 255.255.255.0
    interface Vlan20
    nameif servers
    security-level 100
    ip address 192.168.20.1 255.255.255.0
    interface Vlan30
    nameif printers
    security-level 100
    ip address 192.168.30.1 255.255.255.0
    interface Vlan40
    nameif wireless
    security-level 100
    ip address 192.168.40.1 255.255.255.0
    banner login line Welcome to Payback Loyalty Systems
    boot system disk0:/asa901-k8.bin
    ftp mode passive
    clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns domain-lookup servers
    dns domain-lookup printers
    dns domain-lookup wireless
    dns server-group DefaultDNS
    name-server 83.147.160.2
    name-server 83.147.160.130
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network ftp_server
    object network Internal_Report_Server
    host 192.168.20.21
    description Automated Report Server Internal Address
    object network Report_Server
    host 89.234.126.9
    description Automated Report Server
    object service RDP
    service tcp destination eq 3389
    description RDP to Server
    object network Host_QA_Server
    host 89.234.126.10
    description QA Host External Address
    object network Internal_Host_QA
    host 192.168.20.22
    description Host of VM machine for QA
    object network Internal_QA_Web_Server
    host 192.168.20.23
    description Web Server in QA environment
    object network Web_Server_QA_VM
    host 89.234.126.11
    description Web server in QA environment
    object service SQL_Server
    service tcp destination eq 1433
    object network Demo_Server
    host 89.234.126.12
    description Server set up to Demo Product
    object network Internal_Demo_Server
    host 192.168.20.24
    description Internal IP Address of Demo Server
    object network NETWORK_OBJ_192.168.20.0_24
    subnet 192.168.20.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_26
    subnet 192.168.50.0 255.255.255.192
    object network NETWORK_OBJ_192.168.0.0_16
    subnet 192.168.0.0 255.255.0.0
    object service MSSQL
    service tcp destination eq 1434
    description MSSQL port
    object network VPN-network
    subnet 192.168.50.0 255.255.255.0
    object network NETWORK_OBJ_192.168.50.0_24
    subnet 192.168.50.0 255.255.255.0
    object service TS
    service tcp destination eq 4400
    object service TS_Return
    service tcp source eq 4400
    object network External_QA_3
    host 89.234.126.13
    object network Internal_QA_3
    host 192.168.20.25
    object network Dev_WebServer
    host 192.168.20.27
    object network External_Dev_Web
    host 89.234.126.14
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    description Wireless network
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq ftp
    service-object tcp destination eq netbios-ssn
    service-object tcp destination eq smtp
    service-object object TS
    service-object object SQL_Server
    object-group service DM_INLINE_SERVICE_3
    service-object tcp destination eq www
    service-object tcp destination eq https
    service-object object TS
    service-object object TS_Return
    object-group service DM_INLINE_SERVICE_4
    service-object object RDP
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group service DM_INLINE_SERVICE_5
    service-object object MSSQL
    service-object object RDP
    service-object object TS
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group service DM_INLINE_SERVICE_6
    service-object object TS
    service-object object TS_Return
    service-object tcp destination eq www
    service-object tcp destination eq https
    object-group network DM_INLINE_NETWORK_1
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    object-group network Payback_Internal
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.20.0 255.255.255.0
    network-object 192.168.40.0 255.255.255.0
    access-list outside_access_in remark This rule is allowing from internet to interal server.
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark FTP
    access-list outside_access_in remark RDP
    access-list outside_access_in remark SMTP
    access-list outside_access_in remark Net Bios
    access-list outside_access_in remark SQL
    access-list outside_access_in remark TS - 4400
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any4 object Internal_Report_Server
    access-list outside_access_in remark Access rule to internal host QA
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit tcp any4 object Internal_Host_QA eq www
    access-list outside_access_in remark Access to INternal Web Server:
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark HTTP
    access-list outside_access_in remark RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_3 any4 object Internal_QA_Web_Server
    access-list outside_access_in remark Rule for allowing access to Demo server
    access-list outside_access_in remark Allowed:
    access-list outside_access_in remark RDP
    access-list outside_access_in remark MSSQL
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any4 object Internal_Demo_Server
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
    access-list outside_access_in remark Access for Development WebServer
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
    access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
    access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
    access-list AnyConnect_Client_Local_Print remark Windows' printing port
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
    access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
    access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
    access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
    access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
    access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
    access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
    access-list Payback_VPN_splitTunnelAcl standard permit 192.168.20.0 255.255.255.0
    access-list outside_cryptomap extended permit ip object-group DM_INLINE_NETWORK_1 192.168.100.0 255.255.255.0
    pager lines 24
    logging enable
    logging console informational
    logging asdm informational
    logging from-address [email protected]
    logging recipient-address [email protected] level alerts
    mtu outside 1500
    mtu inside 1500
    mtu servers 1500
    mtu printers 1500
    mtu wireless 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (wireless,outside) source static Wireless Wireless destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Servers Servers destination static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 no-proxy-arp route-lookup
    nat (inside,outside) source dynamic any interface
    nat (wireless,outside) source dynamic any interface
    nat (servers,outside) source dynamic any interface
    nat (servers,outside) source static Internal_Report_Server Report_Server
    nat (servers,outside) source static Internal_Host_QA Host_QA_Server
    nat (servers,outside) source static Internal_QA_Web_Server Web_Server_QA_VM
    nat (servers,outside) source static Internal_Demo_Server Demo_Server
    nat (servers,outside) source static NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 destination static NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 no-proxy-arp route-lookup
    nat (servers,outside) source static Internal_QA_3 External_QA_3
    nat (servers,outside) source static Dev_WebServer External_Dev_Web
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.10.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer XX.XX.XX.XX
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map inside_map interface inside
    crypto map servers_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map servers_map interface servers
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside client-services port 443
    crypto ikev2 enable inside client-services port 443
    crypto ikev1 enable outside
    crypto ikev1 enable inside
    crypto ikev1 enable servers
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 192.168.10.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd dns 192.168.0.1
    dhcpd auto_config outside
    dhcpd address 192.168.10.21-192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    dhcpd option 15 ascii paybackloyalty.com interface inside
    dhcpd enable inside
    dhcpd address 192.168.40.21-192.168.40.240 wireless
    dhcpd dns 192.168.20.21 83.147.160.2 interface wireless
    dhcpd update dns interface wireless
    dhcpd option 15 ascii paybackloyalty.com interface wireless
    dhcpd enable wireless
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy Payback_VPN internal
    group-policy Payback_VPN attributes
    vpn-simultaneous-logins 10
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Payback_VPN_splitTunnelAcl
    group-policy DfltGrpPolicy attributes
    dns-server value 83.147.160.2 83.147.160.130
    vpn-tunnel-protocol ikev1 ikev2 ssl-clientless
    group-policy GroupPolicy_84.39.233.50 internal
    group-policy GroupPolicy_84.39.233.50 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username Noelle password XB/IpvYaATP.2QYm encrypted
    username Noelle attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Eanna password vXILR9ZZQIsd1Naw encrypted privilege 0
    username Eanna attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Michael password qpbleUqUEchRrgQX encrypted
    username Michael attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Danny password .7fEXdzESUk6S/cC encrypted privilege 0
    username Danny attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username niamh password MlFlIlEiy8vismE0 encrypted
    username niamh attributes
    service-type admin
    username Aileen password tytrelqvV5VRX2pz encrypted privilege 0
    username Aileen attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Aidan password aDu6YH0V5XaxpEPg encrypted privilege 0
    username Aidan attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    username shane.c password iqGMoWOnfO6YKXbw encrypted
    username shane.c attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Shane password yQeVtvLLKqapoUje encrypted privilege 0
    username Shane attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username James password TdYPv1pvld/hPM0d encrypted
    username James attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username mark password yruxpddqfyNb.qFn encrypted
    username mark attributes
    service-type admin
    username Mary password XND5FTEiyu1L1zFD encrypted
    username Mary attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    username Massimo password vs65MMo4rM0l4rVu encrypted privilege 0
    username Massimo attributes
    vpn-group-policy Payback_VPN
    service-type remote-access
    tunnel-group Payback_VPN type remote-access
    tunnel-group Payback_VPN general-attributes
    address-pool VPN1
    default-group-policy Payback_VPN
    tunnel-group Payback_VPN ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 general-attributes
    default-group-policy GroupPolicy_84.39.233.50
    tunnel-group 84.39.233.50 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map global-class
    match default-inspection-traffic
    policy-map global-policy
    class global-class
      inspect dns
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect ip-options
      inspect netbios
      inspect pptp
      inspect rsh
      inspect rtsp
      inspect sip
      inspect snmp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
      inspect icmp error
      inspect icmp
    service-policy global-policy global
    smtp-server 192.168.20.21
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:83fa7ce1d93375645205f6e79b526381
    ASA2:
    ASA Version 9.0(1)
    hostname Payback-CIX
    enable password HSMurh79NVmatjY0 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    description This port connects to VLAN 100
    switchport access vlan 100
    interface Ethernet0/2
    interface Ethernet0/3
    switchport access vlan 100
    interface Ethernet0/4
    switchport access vlan 100
    interface Ethernet0/5
    switchport access vlan 100
    interface Ethernet0/6
    switchport access vlan 100
    interface Ethernet0/7
    switchport access vlan 100
    interface Vlan2
    nameif outside
    security-level 0
    ip address X.X.X.X 255.255.255.240
    interface Vlan100
    nameif inside
    security-level 100
    ip address 192.168.100.1 255.255.255.0
    banner login line Welcome to Payback Loyalty - CIX
    ftp mode passive
    clock timezone GMT 0
    clock summer-time gmt/idt recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup outside
    dns domain-lookup inside
    dns server-group defaultDNS
    name-server 8.8.8.8
    name-server 8.8.4.4
    same-security-traffic permit inter-interface
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network CIX-Host-1
    host 192.168.100.2
    description This is the host machine of the VM servers
    object network External_CIX-Host-1
    host 84.39.233.51
    description This is the external IP address of the host server for the VM server
    object service RDP
    service tcp source range 1 65535 destination eq 3389
    object network Payback_Office
    host 92.51.193.158
    object service MSQL
    service tcp destination eq 1433
    object network Development_OLTP
    host 192.168.100.10
    description VM for Eiresoft
    object network External_Development_OLTP
    host 84.39.233.52
    description This is the external IP address for the VM for Eiresoft
    object network External_TMC_Web
    host 84.39.233.53
    description Public Address of TMC Webserver
    object network TMC_Webserver
    host 192.168.100.19
    description Internal Address of TMC Webserver
    object network External_TMC_OLTP
    host 84.39.233.54
    description Targets OLTP external IP
    object network TMC_OLTP
    host 192.168.100.18
    description Targets interal IP address
    object network External_OLTP_Failover
    host 84.39.233.55
    description Public IP of OLTP Failover
    object network OLTP_Failover
    host 192.168.100.60
    description Server for OLTP failover
    object network Servers
    subnet 192.168.20.0 255.255.255.0
    object network Wired
    subnet 192.168.10.0 255.255.255.0
    object network Wireless
    subnet 192.168.40.0 255.255.255.0
    object network NETWORK_OBJ_192.168.100.0_24
    subnet 192.168.100.0 255.255.255.0
    object network NETWORK_OBJ_192.168.10.0_24
    subnet 192.168.10.0 255.255.255.0
    object network Eiresoft_2nd
    host 137.117.217.29
    description Eiresoft 2nd IP
    object network Dev_Test_Webserver
    host 192.168.100.12
    description Dev Test Webserver Internal Address
    object network External_Dev_Test_Webserver
    host 84.39.233.56
    description This is the PB Dev Test Webserver
    object network NETWORK_OBJ_192.168.1.0_24
    subnet 192.168.1.0 255.255.255.0
    object network LAN
    subnet 192.168.100.0 255.255.255.0
    object network REMOTE-LAN
    subnet 192.168.10.0 255.255.255.0
    object network TargetMC
    host 83.71.194.145
    description This is Target Location that will be accessing the Webserver
    object network Rackspace_OLTP
    host 162.13.34.56
    description This is the IP address of production OLTP
    object service DB
    service tcp destination eq 5022
    object network Topaz_Target_VM
    host 82.198.151.168
    description This is Topaz IP that will be accessing Targets VM
    object service DB_2
    service tcp destination eq 5023
    object network EireSoft_NEW_IP
    host 146.66.161.3
    description Eiresoft latest IP form ISP DHCP
    object-group service DM_INLINE_SERVICE_1
    service-object object MSQL
    service-object object RDP
    service-object icmp echo
    service-object icmp echo-reply
    object-group service DM_INLINE_SERVICE_2
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_4
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    service-object tcp destination eq www
    object-group service DM_INLINE_SERVICE_5
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_6
    service-object object MSQL
    service-object object RDP
    object-group network Payback_Intrernal
    network-object object Servers
    network-object object Wired
    network-object object Wireless
    object-group service DM_INLINE_SERVICE_8
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_9
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_10
    service-object object MSQL
    service-object object RDP
    service-object tcp destination eq ftp
    service-object icmp echo
    service-object icmp echo-reply
    service-object object DB
    object-group service DM_INLINE_SERVICE_11
    service-object object RDP
    service-object tcp destination eq ftp
    object-group service DM_INLINE_SERVICE_12
    service-object object MSQL
    service-object icmp echo
    service-object icmp echo-reply
    service-object object DB
    service-object object DB_2
    object-group service DM_INLINE_SERVICE_13
    service-object object MSQL
    service-object object RDP
    object-group service DM_INLINE_SERVICE_14
    service-object object MSQL
    service-object object RDP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-Host-1
    access-list outside_access_in remark Development OLTP from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver
    access-list outside_access_in remark Access to OLTP for target from Payback Office
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover
    access-list outside_access_in remark Access for the 2nd IP from Eiresoft
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP
    access-list outside_access_in remark Access from the 2nd Eiresoft IP
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP
    access-list outside_access_in remark Access rules from Traget to CIX for testing
    access-list outside_access_in extended permit tcp object TargetMC object TMC_Webserver eq www
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_12 object Rackspace_OLTP object OLTP_Failover
    access-list outside_access_in remark Topaz access to Target VM
    access-list outside_access_in extended permit tcp object Topaz_Target_VM object TMC_Webserver eq www
    access-list outside_access_in remark Opened up for Target for the weekend. Closing on Monday 20th
    access-list outside_access_in extended permit tcp any object TMC_Webserver eq www
    access-list outside_access_in remark Access for Eiresoft after their ISP changed their IP Address
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_13 object EireSoft_NEW_IP object Development_OLTP
    access-list outside_access_in remark Eiresoft Access after ISP changed their IP Address
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_14 object EireSoft_NEW_IP object OLTP_Failover
    access-list outside_cryptomap extended permit ip 192.168.100.0 255.255.255.0 object-group Payback_Intrernal
    pager lines 24
    logging enable
    logging console debugging
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,outside) source static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 destination static Payback_Intrernal Payback_Intrernal no-proxy-arp route-lookup
    nat (inside,outside) source static CIX-Host-1 External_CIX-Host-1
    nat (inside,outside) source static Development_OLTP External_Development_OLTP
    nat (inside,outside) source static TMC_Webserver External_TMC_Web
    nat (inside,outside) source static TMC_OLTP External_TMC_OLTP
    nat (inside,outside) source static OLTP_Failover External_OLTP_Failover
    nat (inside,outside) source static Dev_Test_Webserver External_Dev_Test_Webserver
    nat (inside,outside) source dynamic LAN interface
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http X.X.X.X 255.255.255.252 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer X.X.X.X
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh X.X.X.X  255.255.255.240 outside
    ssh X.X.X.X 255.255.255.252 outside
    ssh 192.168.40.0 255.255.255.0 outside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy GroupPolicy_92.51.193.158 internal
    group-policy GroupPolicy_92.51.193.158 attributes
    vpn-tunnel-protocol ikev1 ikev2
    username gordon password 6e6Djaz3W/XH59zX encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 general-attributes
    default-group-policy GroupPolicy_92.51.193.158
    tunnel-group 92.51.193.158 ipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:78a7b9ccec2fa048306092eb29a2b769

  • CISCO ASA 5505 Split Tunnel DNS with Site to Site VPN

    I have a working configuration for Site to Site VPN between our head office and a private AWS VPC instance.
    The tunnel is active and I can ping the IP address of the remote network and connect to the remote machines using the IP address, but we need to use the FQDN and not the IP.  We have a DNS server set up in AWS for any DNS queries for the remote domain name.
    My question is whether or not the ASA 5505 supports a DNS split tunnel for Site to Site VPN and how it can be configured.
    I can not find where I can interogate the DNS query to be redirected to the VPN tunnel when our domain name is used in a DNS query.  Thus, any pings I try with the FQDN of our servers in AWS are failing as they are going to the default DNS, which is the internet.
    Can any one point me in the right direction on how to configure this DNS rewrite so that we can access our AWS private cloud using FQDN from our AWS domain rather than an IP address?

    Jose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface.  Try to be more restrictive than an '...ip any any' rule for outside_in connections.  For instance, this is what I have for incoming VOIP (access list and nat rules):
    access list rule:
    access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
    nat rule:
    nat (inside,outside) source static server interface service voip-range voip-range
    - 'server' is a network object *
    - 'voip-range' is a service group range
    I'd assume you can do something similar here in combination with my earlier comment:
    access-list incoming extended permit tcp any any eq 5900
    Can you explain your forwarding methodology a little more?  I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to.  Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ?

  • Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall

    Hi,
    I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
    When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
    After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
    They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
    Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
    3
    Nov 21 2012
    07:11:09
    713902
    Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
    3
    Nov 21 2012
    07:11:09
    713902
    Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
    3
    Nov 21 2012
    07:11:09
    713061
    Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
    5
    Nov 21 2012
    07:11:09
    713119
    Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
    Here is from the syntax: show crypto isakmp sa
    Result of the command: "show crypto isakmp sa"
       Active SA: 1
        Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
    Total IKE SA: 1
    1   IKE Peer: 195.149.180.254
        Type    : L2L             Role    : responder
        Rekey   : no              State   : MM_ACTIVE
    Result of the command: "show crypto ipsec sa"
    interface: outside
        Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
          access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
          local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
          current_peer:195.149.180.254
          #pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
          #pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
          path mtu 1500, ipsec overhead 74, media mtu 1500
          current outbound spi: E715B315
        inbound esp sas:
          spi: 0xFAC769EB (4207372779)
             transform: esp-aes-256 esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 5, }
             slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
             sa timing: remaining key lifetime (kB/sec): (38738/2061)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0xE715B315 (3876958997)
             transform: esp-aes-256 esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 5, }
             slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
             sa timing: remaining key lifetime (kB/sec): (38673/2061)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
    And here are my Accesslists and vpn site to site config:
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 84600
    crypto isakmp nat-traversal 40
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto map CustomerCryptoMap 10 match address VPN_Tunnel
    crypto map CustomerCryptoMap 10 set pfs group5
    crypto map CustomerCryptoMap 10 set peer 195.149.180.254
    crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
    crypto map CustomerCryptoMap interface outside
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
    access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
    access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
    nat (inside) 0 access-list nonat
    All these remote networks are at the Main Site Clavister Firewall.
    Best Regards
    Michael

    Hi,
    I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
    If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
    Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
    I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
    Maybe you could try to change the Encryption Domain configurations a bit and test it then.
    You could also maybe take some debugs on the Phase2 and see if you get anymore  hints as to what could be the problem when only one network is working for the L2L VPN.
    - Jouni

  • Can't ping from DC1 behind TMG1 to DC2 behind TMG2 on a site-to-site VPN connection

    Hi,
    I have a weird problem. I have two TMG servers on each site in a hyper-v lab environment. I have been able to establish the site-to-site VPN successfully however when I ping from DC1 behind TMG1(on site 1) to TMG2, DC2, i am able to ping. However the opposite
    doesn't work. After some trial and error, I figured out that the one initiating the demand-dial request is able to ping the other site, not vice-versa..very strange. I would like to know whether ICMP requests could be achieved bi-directionally..
    Secondly, I am able to ping from TMG1 to all the clients sitting behind TMG2 (including the TMG host), however the clients sitting behind TMG1 can't ping TMG2 neither any of the clients behind it. I tried every possible combination under the firewall policies
    but of complete vain. hell, I am starting to develop a very bad feeling about this product because of making such simple tasks overly complex. I mean, if it were a Cisco or Sonicwall, we could have done this so easily. 
    What my final motive is to send LDAP requests from DC1 to DC2 and vice-versa over a site-to-site VPN so that I could set up 2 different sites in AD on different subnets and then proceed with configuring DAG. But if this simple thing turns out to be such
    major roadblock, dunno how am I gonna pass DAG traffic over it.
    Can someone PLEASE help me!! I am completely exhausted researching on this issue.
    Regards,
    Dman

    Hi，
    For site2site VPN, you must create proper network rule and network set and you need to create proper access rule to allow or deny the traffic between VPN network and any other network.
    http://technet.microsoft.com/en-us/library/bb838949.aspx
    Best Regards
    Quan Gu

  • Configure a VPN client and Site to Site VPN tunnel

    Hi, I'm setting up a test network between 2 sites. SiteA has a 515E PIX and SiteB has a 501 PIX. Both sites have been setup with a site to site VPN tunnel, see SiteA config below. I also require that remote clients using Cisco VPN client 3.6 be able to connect into SiteA, be authenticated, get DHCP info and connect to hosts inside the network. However, when I add these config lines, see below, to SiteA PIX it stops the vpn tunnel to SiteB. However, the client can conect and do as needed so that part of my config is correct but I cannot see why the site to site vpn tunnel is then no longer.
    SiteA config with working VPN tunnel to SiteB:
    SITE A
    PIX Version 6.3(1)
    interface ethernet0 auto
    interface ethernet1 auto
    interface ethernet2 auto shutdown
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    nameif ethernet2 webdmz security20
    enable password xxx
    passwd xxx
    hostname SiteA-pix
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol ils 389
    fixup protocol rsh 514
    fixup protocol rtsp 554
    no fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    names
    name 200.x.x.0 SiteA_INT
    name 201.x.x.201 SiteA_EXT
    name 200.x.x.254 PIX_INT
    name 10.10.10.0 SiteB_INT
    name 11.x.x.11 SiteB_EXT
    access-list inside_outbound_nat0_acl permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
    access-list outside_cryptomap_20 permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
    access-list acl_inside permit icmp any any
    access-list acl_inside permit ip any any
    access-list acl_outside permit ip any any
    access-list acl_outside permit icmp any any
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    mtu webdmz 1500
    ip address outside SiteA_EXT 255.x.x.128
    ip address inside PIX_INT 255.255.0.0
    no ip address webdmz
    ip audit info action alarm
    ip audit attack action alarm
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_outbound_nat0_acl
    route outside 0.0.0.x.x.0.0 201.201.201.202 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server RADIUS protocol radius
    aaa-server LOCAL protocol local
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    sysopt connection permit-ipsec
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto map outside_map 20 ipsec-isakmp
    crypto map outside_map 20 match address outside_cryptomap_20
    crypto map outside_map 20 set peer SiteB_EXT
    crypto map outside_map 20 set transform-set ESP-DES-MD5
    crypto map outside_map interface outside
    isakmp enable outside
    isakmp key secret address SiteB_EXT netmask 255.255.255.255 no-xauth no-config-mode
    isakmp policy 20 authentication pre-share
    isakmp policy 20 encryption des
    isakmp policy 20 hash md5
    isakmp policy 20 group 2
    isakmp policy 20 lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    terminal width 80
    SiteA-pix(config)#
    Lines I add for Cisco VPN clients is attached
    I entered each line one by one and did a reload and sh crypto map all was OK until I entered the crypto map VPNPEER lines.
    Anyone any ideas what this can be?
    Thanks

    Heres my config:
    PIX Version 6.3(1)
    interface ethernet0 auto
    interface ethernet1 auto
    interface ethernet2 auto shutdown
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    nameif ethernet2 webdmz security20
    enable password xxx
    passwd xxx
    hostname SiteA-pix
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol ils 389
    fixup protocol rsh 514
    fixup protocol rtsp 554
    no fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    names
    name 200.x.x.0 SiteA_INT
    name 201.x.x.201 SiteA_EXT
    name 200.x.x.254 PIX_INT
    name 10.10.10.0 SiteB_INT
    name 11.11.11.11 SiteB_EXT
    access-list inside_outbound_nat0_acl permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
    access-list outside_cryptomap_20 permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
    access-list acl_inside permit icmp any any
    access-list acl_inside permit ip any any
    access-list acl_outside permit ip any any
    access-list acl_outside permit icmp any any
    access-list 80 permit ip SiteA_INT 255.255.0.0 200.220.0.0 255.255.0.0
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    mtu webdmz 1500
    ip address outside SiteA_EXT 255.255.255.128
    ip address inside PIX_INT 255.255.0.0
    no ip address webdmz
    ip audit info action alarm
    ip audit attack action alarm
    ip local pool pix_inside 200.x.x.100-200.220.200.150
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_outbound_nat0_acl
    route outside 0.0.0.0 0.0.0.x.x.201.202 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server RADIUS protocol radius
    aaa-server RADIUS (inside) host 200.200.200.20 letmein timeout 10
    aaa-server LOCAL protocol local
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    sysopt connection permit-ipsec
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set AAADES esp-3des esp-md5-hmac
    crypto dynamic-map DYNOMAP 10 match address 80
    crypto dynamic-map DYNOMAP 10 set transform-set AAADES
    crypto map outside_map 20 ipsec-isakmp
    crypto map outside_map 20 match address outside_cryptomap_20
    crypto map outside_map 20 set peer SiteB_EXT
    crypto map outside_map 20 set transform-set ESP-DES-MD5
    crypto map outside_map 30 ipsec-isakmp dynamic DYNOMAP
    crypto map outside_map client authentication RADIUS
    crypto map outside_map interface outside
    isakmp enable outside
    isakmp key secret address SiteB_EXT netmask 255.255.255.255 no-xauth no-config-mode
    isakmp policy 20 authentication pre-share
    isakmp policy 20 encryption des
    isakmp policy 20 hash md5
    isakmp policy 20 group 2
    isakmp policy 20 lifetime 86400
    isakmp policy 30 authentication pre-share
    isakmp policy 30 encryption 3des
    isakmp policy 30 hash sha
    isakmp policy 30 group 2
    isakmp policy 30 lifetime 86400
    vpngroup Remote address-pool pix_inside
    vpngroup Remote dns-server 200.200.200.20
    vpngroup Remote wins-server 200.200.200.20
    vpngroup Remote default-domain mycorp.co.uk
    vpngroup Remote idle-time 1800
    vpngroup Remote password password
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    terminal width 80
    I will attach debug output later today.
    Thanks

  • One router on ASA 5505 Site to Site VPN can't ping other router

    I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
    Result of the command: "show running-config"
    : Saved
    ASA Version 8.4(4)1
    hostname SaskASA
    enable password POgOWyKyb0jgJ1Hm encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.16.1 255.255.254.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network NETWORK_OBJ_192.168.16.0_23
    subnet 192.168.16.0 255.255.254.0
    object network NETWORK_OBJ_192.168.2.0_23
    subnet 192.168.2.0 255.255.254.0
    access-list outside_cryptomap extended permit ip 192.168.16.0 255.255.254.0 192.168.2.0 255.255.254.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source static NETWORK_OBJ_192.168.16.0_23 NETWORK_OBJ_192.168.16.0_23 destination static NETWORK_OBJ_192.168.2.0_23 NETWORK_OBJ_192.168.2.0_23 no-proxy-arp route-lookup
    object network obj_any
    nat (inside,outside) dynamic interface
    nat (inside,outside) after-auto source dynamic any interface
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable 444
    http 192.168.16.0 255.255.254.0 inside
    http 0.0.0.0 0.0.0.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs group1
    crypto map outside_map 1 set peer 207.228.xx.xx
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map interface outside
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    dhcp-client client-id interface outside
    dhcpd auto_config outside
    dhcpd address 192.168.16.100-192.168.16.200 inside
    dhcpd auto_config outside interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy GroupPolicy_207.228.xx.xxinternal
    group-policy GroupPolicy_207.228.xx.xx attributes
    vpn-tunnel-protocol ikev1 ikev2
    username User password shbn5zbLkuHP/mJX encrypted privilege 15
    tunnel-group 207.228.xx.xxtype ipsec-l2l
    tunnel-group 207.228.xx.xxgeneral-attributes
    default-group-policy GroupPolicy_207.228.xx.xx
    tunnel-group 207.228.xx.xxipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum client auto
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    inspect ip-options
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f06bd1d6d063318339d98417b171175e
    : end
    Any ideas? Thanks.

    I looked over the config for Site A, but couldn't find anything unusual. Perhaps I'm overlooking something. Here is the config for site A:
    Result of the command: "show running-config"
    : Saved
    ASA Version 8.2(1)
    hostname SiteA
    domain-name domain
    enable password POgOWyKyb0jgJ1Hm encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.2.1 255.255.254.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns domain-lookup inside
    dns server-group DefaultDNS
    name-server 192.168.2.6
    domain-name domain
    object-group network DM_INLINE_NETWORK_1
    network-object 192.168.14.0 255.255.254.0
    network-object 192.168.4.0 255.255.254.0
    network-object 192.168.6.0 255.255.254.0
    network-object 192.168.8.0 255.255.254.0
    object-group network DM_INLINE_NETWORK_2
    network-object 192.168.12.0 255.255.254.0
    network-object 192.168.14.0 255.255.254.0
    network-object 192.168.4.0 255.255.254.0
    network-object 192.168.6.0 255.255.254.0
    network-object 192.168.8.0 255.255.254.0
    access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_1
    access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_2
    access-list inside_nat0_outbound extended permit ip any 192.168.15.192 255.255.255.192
    access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
    access-list VPNGeo_splitTunnelAcl standard permit any
    access-list outside_2_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.6.0 255.255.254.0
    access-list outside_3_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.4.0 255.255.254.0
    access-list outside_4_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.8.0 255.255.254.0
    access-list outside_5_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool GeoVPNPool 192.168.15.200-192.168.15.254 mask 255.255.254.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable 444
    http 192.168.2.0 255.255.254.0 inside
    http 0.0.0.0 0.0.0.0 inside
    http 0.0.0.0 0.0.0.0 outside
    http authentication-certificate inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group1
    crypto map outside_map 1 set peer 207.228.xx.xx
    crypto map outside_map 1 set transform-set ESP-3DES-SHA
    crypto map outside_map 2 match address outside_2_cryptomap
    crypto map outside_map 2 set pfs
    crypto map outside_map 2 set peer 208.119.xx.xx
    crypto map outside_map 2 set transform-set ESP-3DES-SHA
    crypto map outside_map 3 match address outside_3_cryptomap
    crypto map outside_map 3 set pfs group1
    crypto map outside_map 3 set peer 208.119.xx.xx
    crypto map outside_map 3 set transform-set ESP-3DES-SHA
    crypto map outside_map 4 match address outside_4_cryptomap
    crypto map outside_map 4 set pfs
    crypto map outside_map 4 set peer 208.119.xx.xx
    crypto map outside_map 4 set transform-set ESP-3DES-SHA
    crypto map outside_map 5 match address outside_5_cryptomap
    crypto map outside_map 5 set pfs group1
    crypto map outside_map 5 set peer 70.64.xx.xx
    crypto map outside_map 5 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcp-client client-id interface outside
    dhcpd auto_config outside
    dhcpd address 192.168.2.100-192.168.2.254 inside
    dhcpd auto_config outside interface inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy VPNGeo internal
    group-policy VPNGeo attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value VPNGeo_splitTunnelAcl
    username user password shbn5zbLkuHP/mJX encrypted privilege 15
    username namepassword vP98Lj8Vm5SLs9PW encrypted
    username nameattributes
    vpn-group-policy VPNGeo
    tunnel-group 207.228.xx.xxtype ipsec-l2l
    tunnel-group 207.228.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group VPNGeo type remote-access
    tunnel-group VPNGeo general-attributes
    address-pool GeoVPNPool
    default-group-policy VPNGeo
    tunnel-group VPNGeo ipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xxtype ipsec-l2l
    tunnel-group 208.119.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xx type ipsec-l2l
    tunnel-group 208.119.xx.xx ipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xxtype ipsec-l2l
    tunnel-group 208.119.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group 70.64.xx.xxtype ipsec-l2l
    tunnel-group 70.64.xx.xxipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:e3adf4e597198f58cd21e508aabdbab9
    : end

  • Question in asa site-site vpn about "ident" ??

    hi all ,
    i have a topology as
    (192.168.0.0/24)LAN1----------------asa1---------------internet-----------------------asa2------------------LAN2(192.168.2.0/24)
    now , lan 1 can reach lan 2 by site to site vpn
    but i have a question :
    when i have
    #sh crypto ipsec sa
    ====================================================================
    interface: outside
        Crypto map tag: Azure_IPSecCryptoMap, seq num: 2, local addr: xxxx
          access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 any
          local ident (addr/mask/prot/port): (192.168.0.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
          current_peer: xxxxx
          #pkts encaps: 294823, #pkts encrypt: 294823, #pkts digest: 294823
          #pkts decaps: 208795, #pkts decrypt: 208795, #pkts verify: 208795
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 294823, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: xxxxxxxxxx/0, remote crypto endpt.: xxxxxxxx/0
          path mtu 1500, ipsec overhead 74, media mtu 1500
          current outbound spi: 81F3ABF6
          current inbound spi : FAE91312
        inbound esp sas:
          spi: 0xFAE91312 (4209578770)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 2, }
             slot: 0, conn_id: 10670080, crypto-map: Azure_IPSecCryptoMap
             sa timing: remaining key lifetime (kB/sec): (4373327/621)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0x81F3ABF6 (2180230134)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, PFS Group 2, }
             slot: 0, conn_id: 10670080, crypto-map: Azure_IPSecCryptoMap
             sa timing: remaining key lifetime (kB/sec): (4370375/621)
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
    ================================================================================
    my problem is ,
    that my asa1 lan1  only reach asa2 if its destination was to subnet 192.168.2.0/24 , i mean if  requested internet i cant reach it !!!
    note that the crypto_map acl says destination "any" will go to asa2 , but why  when i requested the destioantion of lan2 it responce , and if i requested 8.8.8.8 it dont reach asa2 ??
    i used packet tracer to investigate  , it seems as a stuck !!!
    how to change the remote idnet as in the red line above ??? i think it is the issue that preventing mefrom reaching internet by asa2
    agian ,
    what issue in the asa has relation to the remote idnet and how i can change it ?
    any help ?
    regards

    CSCO,
    The lines below, match the interesting traffic for this VPN. You will not see a specific host address unless, you configure that within you crypto ACL. Basically you have some host in network 192.168.0.0/24(LOCAL) going to 192.168.2.0/24(REMOTE). The REMOTE IDENT is the remote network where the remote host relies, which matches your interesting traffic.
    So lon story short, you have some local host in the 192.168.1.0/24 range going to some host in the 192.168.2.0/24 range.
    This ACL has to do with the address you map to the match address line of you crypto map.
          access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 any
          local ident (addr/mask/prot/port): (192.168.0.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)

  • ASA 5520 site-to-site VPN question

    Hello,
    We have a Cisco 5520 ASA 8.2(1) connected to a Cisco RVS4000 router via an IPsec Site-to-Site VPN. The RVS4000 is located at a branch office. The tunnel works beautifully. When computers at the remote site are turned on the tunnel is established, and data is transferred back and forth.
    The only issue I'm having is being able to Remote Desktop to the branch office computers, or ping for that matter. I can ping and Remote Desktop from the branch office computers to computers at the main site where the ASA is located.
    After doing some research, I came across the this command;
    sysopt connection permit-vpn
    I haven't tried entering the command yet, but was wondering if this is something that I can try initially to see it it resolves the problem.
    Thanks,
    John

    What are your configs and network diagrams at each location?  What are you doing for DNS?  I can help quicker with that info.  Also, here are some basic site to site VPN examples if it helps.
    hostname cisco
    domain-name cisco.com
    enable password XXXXXXXX encrypted
    passwd XXXXXXXXXXX encrypted
    names
    dns-guard
    interface Ethernet0/0
    nameif outside
    security-level 0
    ip address XXX.XXX.XXX.XXX 255.255.255.248
    interface Ethernet0/1
    nameif inside
    security-level 100
    ip address 10.0.0.2 255.255.255.0
    interface Ethernet0/2
    nameif backup
    security-level 0
    no ip address
    interface Ethernet0/3
    nameif outsidetwo
    security-level 0
    no ip address
    interface Management0/0
    nameif management
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    management-only
    ftp mode passive
    dns server-group DefaultDNS
    domain-name cisco.com
    same-security-traffic permit intra-interface
    access-list XXX extended permit ip 10.0.0.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list XXX extended permit ip 10.0.10.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list XXX extended permit ip 10.0.2.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list XXX extended permit ip 10.0.4.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list XXX extended permit ip 10.0.0.0 255.255.255.0 10.0.2.0 255.255.255.0
    access-list XXX extended permit ip 10.90.238.0 255.255.255.0 10.0.2.0 255.255.255.0
    access-list XXX extended permit ip 10.0.0.0 255.255.255.0 10.0.4.0 255.255.255.0
    access-list XXX extended permit ip 10.90.238.0 255.255.255.0 10.0.4.0 255.255.255.0
    access-list nonat extended permit ip 10.0.0.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list nonat extended permit ip 10.0.0.0 255.255.255.0 10.0.2.0 255.255.255.0
    access-list nonat extended permit ip 10.0.0.0 255.255.255.0 10.0.4.0 255.255.255.0
    access-list nonat extended permit ip 10.0.0.0 255.255.255.0 10.0.10.0 255.255.255.0
    access-list nonat extended permit ip 10.0.10.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list nonat extended permit ip 10.0.2.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list nonat extended permit ip 10.0.4.0 255.255.255.0 10.90.238.0 255.255.255.0
    access-list split standard permit 10.0.0.0 255.255.255.0
    access-list split standard permit 10.90.238.0 255.255.255.0
    pager lines 24
    logging enable
    logging buffer-size 1048576
    logging buffered errors
    logging trap notifications
    logging asdm informational
    logging class vpn buffered debugging
    mtu outside 1500
    mtu inside 1500
    mtu backup 1500
    mtu outsidetwo 1500
    mtu management 1500
    ip local pool vpnpool 10.0.10.100-10.0.10.200
    ip audit name Inbound-Attack attack action alarm drop
    ip audit name Inbound-Info info action alarm
    ip audit interface outside Inbound-Info
    ip audit interface outside Inbound-Attack
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list nonat
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group inbound in interface outside
    route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    aaa authentication ssh console LOCAL
    http server enable
    http 0.0.0.0 0.0.0.0 inside
    http 192.168.1.0 255.255.255.0 management
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set myset esp-3des esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map dynmap 10 set transform-set myset
    crypto dynamic-map dynmap 10 set security-association lifetime seconds 28800
    crypto dynamic-map dynmap 10 set security-association lifetime kilobytes 4608000
    crypto map outside_map 1 match address XXX
    crypto map outside_map 1 set peer XXX.XXX.XXX.XXX
    crypto map outside_map 1 set transform-set myset
    crypto map outside_map 1 set security-association lifetime seconds 28800
    crypto map outside_map 1 set security-association lifetime kilobytes 4608000
    crypto map outside_map 2 match address XXX2
    crypto map outside_map 2 set peer XXX.XXX.XXX.XXX
    crypto map outside_map 2 set transform-set myset
    crypto map outside_map 2 set security-association lifetime seconds 28800
    crypto map outside_map 2 set security-association lifetime kilobytes 4608000
    crypto map outside_map 3 match address XXX3
    crypto map outside_map 3 set pfs
    crypto map outside_map 3 set peer XXX.XXX.XXX.XXX
    crypto map outside_map 3 set transform-set myset
    crypto map outside_map 3 set security-association lifetime seconds 28800
    crypto map outside_map 3 set security-association lifetime kilobytes 4608000
    crypto map outside_map 65535 ipsec-isakmp dynamic dynmap
    crypto map outside_map interface outside
    crypto isakmp identity address
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh 0.0.0.0 0.0.0.0 outside
    ssh 0.0.0.0 0.0.0.0 inside
    ssh timeout 60
    console timeout 0
    management-access inside
    dhcpd address 192.168.1.2-192.168.1.254 management
    dhcpd enable management
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy XXXgroup internal
    group-policy XXXgroup attributes
    dns-server value XXX.XXX.XXX.XXX
    vpn-idle-timeout 30
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value split
    default-domain value domain.local
    username XXX24 password XXXX encrypted privilege 15
    username admin password XXXX encrypted
    tunnel-group XXX.XXX.XXX.XXX type ipsec-l2l
    tunnel-group XXX.XXX.XXX.XXX ipsec-attributes
    pre-shared-key XXXXXXXXXX
    tunnel-group XXXgroup type remote-access
    tunnel-group XXXgroup general-attributes
    address-pool vpnpool
    default-group-policy rccgroup
    tunnel-group XXXgroup ipsec-attributes
    pre-shared-key XXXXXXXXXX
    isakmp ikev1-user-authentication none
    tunnel-group XXX.XXX.XXX.XXX type ipsec-l2l
    tunnel-group XXX.XXX.XXX.XXX ipsec-attributes
    pre-shared-key XXXXXXXXXX
    tunnel-group XXX.XXX.XXX.XXX type ipsec-l2l
    tunnel-group XXX.XXX.XXX.XXX ipsec-attributes
    pre-shared-key XXXXXXXXXX
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns migrated_dns_map_1
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns migrated_dns_map_1
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily

  • Site to Site VPN with 2 ASA 5510's

    Hello guys,
    Im hoping yall can help me with the following objective. I have been tasked to make a site to site VPN between two networks. We are both using an ASA 5510.
    This is the scenario:
    SiteA has an wan adress of (example) 20.20.20.20  - The firewall is connected to a DMZ range : 192.168.0.0 255.255.255.0. In this range there is another firewall which grants/blocks acces to the internal range. 10.20.0.0 255.255.0.0
    SiteB has an wan adress of (example) 21.21.21.21 - The internal range is 10.0.0.0 255.0.0.0 No DMZ.
    How can i connect these 2 devices since there is an overlap. I am gonna need to use nat right? Can someone give me readable  Access rule/Nat Rule and maybe advice / some other things i need to think of.
    Hope to hear from yall. Any advice is highly appriciated.
    Thanks in advance

    Hi,
    Well regarding the remote site I suppose if they are using hosts from ranges 10.0.1.0/24 and 10.0.2.0/24 they could simply NAT these portions of the network towards the L2L VPN connection. For example NAT them to subnets 192.168.101.0/24 and 192.168.102.0/24
    But you also seem to have a large subnet on your side since its 10.20.0.0/16. Because of this I would suggest narrowing it down to the hosts or smaller subnets like above with the remote site because simply NATing the whole subnet 10.20.0.0/16 to some other private range that is NOT from the 10.0.0.0/8 range would probably cause problems in the long run.
    Lets presume that on your side the network that needs to access the L2L VPN is 10.20.1.0/24 and we would NAT that to 192.168.201.0/24 then your NAT configuration could look like this
    object network DMZ-INTERNAL
      subnet 10.20.1.0 255.255.255.0
    object network DMZ-INTERNAL-NAT
     subnet 192.168.201.0 255.255.255.0
    object-group network REMOTE-NETWORKS
     network-object 192.168.101.0 255.255.255.0
     network-object 192.168.102.0 255.255.255.0
    nat (dmz,outside) 1 source static DMZ-INTERNAL DMZ-INTERNAL-NAT destination static REMOTE-NETWORKS REMOTE-NETWORKS
    In the above configuration we first create an "object" for both the actual internal DMZ subnet and the subnet that we will NAT it to. Then we create an "object-group" that will have inside it both of the remote NATed networks (NAT performed at the remote site).
    Finally the "nat" command itself will perform NAT between "dmz" and "outside" interface and it will NAT "DMZ-INTERNAL" to "DMZ-INTERNAL-NAT" when the destination is "REMOTE-NETWORKS". The NAT configuration is bidirectional so it naturally handles which ever directin the connection is attempted. The names of the objects are up to the user.
    The ACL that defines the local and remote networks for the L2L VPN should use the NAT subnets of each site.
    If you want to restrict the traffic from the remote site then this can be done in a couple of ways. At its default settings the ASA will allow ALL traffic from the remote site behind the L2L VPN connection.
    You can use the command "show run all sysopt" to list some configurations that will tell us how your ASA has been set to handle VPN related traffic. The command we are looking for is "sysopt connection permit-vpn". This is the default setting that allows all traffic from VPN connections. If you were to change this to "no sysopt connection permit-vpn" then you could simply use the interface ACL of the interface that terminates the L2L VPN connection on your side to select what traffic is allowed. You would allow traffic the same way as if you were allowing traffic from Internet to your servers.
    The problem with this setup is if you have other existing VPN connections (VPN Client and L2L VPN) because they would also require their traffic to be allowed in your external interfaces ACL if you changed the above mentioned global setting.
    The other option is to configure a VPN Filter ACL that you will then attach to a "group-policy". You will then attach that "group-policy" to the "tunnel-group" of the L2L VPN connection.
    The actual ACL used for the VPN Filter purpose is a norma ACL but you will always have to configure the remote network as the source in the ACL and this usually causes some confusion.
    - Jouni

Maybe you are looking for

  • When re-installing JRE 1.2.2 I get an error "can't create JAR file"

    When I uninstalled Java Runtime 1.2.2 and reinstalling, at the end of the installation I get an error: "Error while creating JAR file. Check you have enough disk space. See c:\winnt\temp\uncrunch.log for details" Only trouble is I've got 14 GB open a

  • Resetting Leopard to just opened settings

    Hey, so my father just bought a new MacBook pro. I opened the box and was the first to use it. I completed the setup that is required when first using Leopard entering my fathers name for the admin, adding a password for him, etc. He didn't tell me h

  • Business area creation in command line

    Dear Pals, My discoverer version is Discoverer Version:Server 10.1.2.55.26 with EBS r12.0.4. I created EUL using eulapi and given SYSADMIN full access on the same. I've also imported Discoverer loader files. Now it is possible to create a Business ar

  • Need urgent help on these questions

    Q1. What are some of the important ways in which development that is done in connection with building and supporting a software product differs from development of internal applications used for only one business or group of users. Q2. what software

  • Gradient with dither creates artifacts beyond gradation

    Photoshop CC / Mac (also occurs in CS6, I just never took the time to document it) Create a gradient mask from 0 - 255, the mask contains a dot pattern in the area that extends beyond the gradation and should be a solid 0,0,0. The dot/pattern has a v