In Funds Management-Assigned budget is more than the release

Hi Experts,
We have Funds Management active and in few cases the assigned budget is more than the released budget for a funds center and commitment item. We observed that the material consumption (stores requests) entries get posted even when there is no released budget.
Can you suggest ways to control the posing of material consumption entries when there is no released budget in Funds management.
With Regards
ACR.Ruben

hi
Try there is a USER _EXIT for Material consulmption for the Movement type 261 GI to Production .
Extension SAPLFMFA, component EXIT_SAPLFMFA_001
through this you can stop the Material consumption additions to fundcenter through the commit ment item.
Thanks & Regards
Mala K Reddy

Similar Messages

  • Check point in fund management for budget and creation of po

    I have a Budget for a perticular expenses say Rs 100000/-, so the po should not be created for more than Rs 100000/- as per the budget. but the po is been created for more than the budget amount.
    pls. let me know where the check point has to be maintain.
    Thanks
    Santosh Visave
    Moderator: Please, search SDN

    Hi ,
    First of all as a primary step you can do the following :
    1. is the commitment item getting derived in the PO.
    2. Is the commitment item non statistical ( means you have not put the tick on statistical commitment item ) in FMCIA .
    3. check the budget amount via the report FMRP_RW_BUDCON for the budget amount and released amount .
    Hope this would help .
    Cheers ,
    Dewang

  • How to assign values for more than one field

    Hi,
    I have written following code
    constants: fieldname(30) value '(SAPMF02D)KNA1-AUFSD'.
    constants: fieldname1(30) value '(SAPMF02D)KNA1-LISFD'.
    constants: fieldname2(30) value '(SAPMF02D)KNA1-FAKSD'.
    field-symbols: <L_FIELD>  TYPE ANY.
    field-symbols: <L_FIELD1> TYPE ANY.
    field-symbols: <L_FIELD2> TYPE ANY.
          Assign (fieldname) to <l_field>.
          <L_FIELD> = 'ZB'. " value according to your requirement
          Assign (fieldname1) to <l_field1>.
          <L_FIELD1> = 'ZB'.
    while debugging <l_field1> is not assinging (fieldname1).
    Im able to assing for (fieldname).
    how to assign value for (fieldname1).
    plz suggest me to assign values for more than one field.
    Regards,
    Brahmaji

    Hello,
    Because there is no field name called LISFD in KNA1. Actually you misspelled the field name.
    It is KNA1-LIFSD

  • Can an assigned PO use more than one work order?

    Can an assigned PO use more than one work order?

    Hi,
    Please avoid duplicate posting in the forum. You already an active thread which is in progress. there is possibility that Moderators might lock your threads.
    Thanks,
    Sudhakar
    Message was edited by: Sudhakar Pappu
    Next time please mark for moderation so duplicates can be removed - thanks I have locked this thread
    Regards
    Virendra
    Message was edited by: Virendra Pal

  • Funds Management with Budget Control System (BCS) submodule

    hi sap gurus
    can any one give me the details for the
    Funds Management with Budget Control System (BCS) submodule   
    if any material pls send to my mail id : [email protected]
    its very urgent pls
    thank you

    Hi,
    Try executing FMAVCREINIT report and check if the problem persists.
    Regards,
    Eli

  • Restriction of PO if its value is more than the PR vlaue

    Hai PS friends,
    My project structure is WBS- Network- Service Activity with AVAC.
    While Creating Purchase order w.r.t Purchase Requisition, System is not stopping the PO when its value increases more than the PR value.
    But PO is not creating if its value increases more than the Contract.
    If Budget is having more than the assigned value, I need to stop to create if PO value is more than the PR value. Please suggest in this regard.
    with regards
    M Umapathy

    I doubt whether Standard SAP will copy price from PR to PO or not.
    I think you need to maintain Function Authorizations for Buyers in the customization for the following path..
    ...SPRO >>>MM > Purchasing > Authorization Management > Define Function Authorizations for Buyers.
    Please search SDN for further details as there are many threads available.
    Also Referring SAP Note: 456691 will be useful.

  • I need more than the maximum allowed 30 profiles - how do I change this?

    I need more than the maximum allowed 30 profiles - how do I change this? Once I reach 30 profiles and I try to add one - it just deletes one automatically thus only allowing a maximum of 30. Please help.

    You are talking about 30 Firefox Profiles on the same Windows Logon User Account?
    I never saw that as a limit myself. I had 53 Profiles at one time, although I haven't done that since Firefox 3.0. It was causing an extended launch time and I started using "remote" Profiles that weren't controlled by the Profile Manager and weren't in the '''profiles.ini''' file; launched by command line. Like this in the Target line for the desktop shortcut: <br />
    ''' "C:\Program Files\Firefox_4.0_zip\firefox.exe" -Profile D:\Mozilla\Active-Profiles\4.0_10-15-10-N '''

  • When printing a list in Address Book, how can I select more than the default Attributes and keep them selected when I print again? I want to print ALL information for contacts so I have email address, notes, phone, company, title, etc all on one page.

    When printing a list in Address Book, how can I select more than the default Attributes and keep them selected when I print again? I want to print ALL information for contacts so I have email address, notes, phone, company, title, etc all on one page. I don't want to have to check off an additional 5 or 6 attributes each time I print out contact information. Is there a way to change the default setting for printing lists, so it is not just "phone," "photo," and "job title?"

    I have a user who wants to do this same thing. I did not find any way either to default the attributes to anything other than what you see the first time. Seems like such a trivial thing, hard to believe they do not allow it. I did find a program for this called iDress but I can't seem to download it from any links on the Internet. Not sure if it is free or not, but it was recommended by a link on the Mac support site.

  • Confirmed quantity more than the ordered quantity in sales order.

    Hi All,
    We have a situation wherein the confirmed quantity is more than the ordered quantity.
    a.) SO was created for qty1.Two schedule lines were proposed as stock was not available.
    b.) When stock came in and most probablly, when the rescheduling job calling tcode  V_V2 was run, both the schedule lines were confirmed.
    c.) As a result, further processing  is not done by system as confirmed quantity is more than ordered quantity.
    Also we noticed that double schedule line was confirmed for a another order even without the rescheduling job is run.
    Can you please suggest as to why this is scenario is occuring and how we can avoid the reoccurence? Thanks in advance!!
        Regards,
    Jeevan Penumatsa

    Hi  Jeevan Penumatsa
    Welcome to SDN forum
    Generally two schedule lines will take place if stock is not available in your plant or if open orders are there for that material also. So check the stock in MMBE
    .If there are any backorders then it might be getting added in the created sales order and then you might be getting in two schedule lines
    Regards
    Srinath

  • Gross price of Service entry Sheet more than the value ordered in PO

    Hi all!!
    I have a PO that were created and changed by the following way:
    The user created the PO of service with the quantity = 1 and the price = 50.000,00
    Than he made the service entry sheet of this PO and MIRO normally.
    As the fields on service tab wasn't blocked, the user changed the quantity to 105.000,00 and the price to 1.
    After that, he made 3 services entry sheet to complete 105.000,00 quantities.
    With this, the value delivered became bigger than the value ordered in the PO.
    if I make a service entry sheet with a quantity of 200.000,00 for example, the message SE363 will be shown to me with a message that the "quantity entered exceeds quantity in purchase order".
    I'd like to know if there's a way by customizing of control the price on Service entry sheet based on the value ordered in PO instead of quantity.
    Can anybody help me?
    Thanks in advance,
    Cris

    Hi Ajit and Rajesh
    Thanks for the response.
    The user made a PO with one line with quantity 1 and net price 50.000,00.
    In the services tab, he put a sevice with quantitiy 1 and gross price 50.000,00, and than made the service sheet entry, and MIRO.
    After this he changed in the services tab the quantity to 105.000,00 and the gross price to 1 (with the objective of making more than one service entry sheet by quantity).
    With this, the system let the user make many entries of service allowing the user to make entries os sheet more than the net price that is in the line of PO.
    I'd like to know if there's a way configure the system to make a compare between the gross price and the net price when i'm doing the service entry sheet, because now when I change a line of service tab, the system is not considering that other service entry sheet were made.
    So that, i'm having the value of ordered bigger than the value delivered.
    Nowadays, the block is made by quantity as I said, but i'd like to block by price too.
    Sorry about the bad explanation before, I hope that now i explained better.
    Thanks
    Cris

  • System is allowing to post the Adv Pmt amount more than the PO Value

    Hi Experts,
    I am FICO Consultant. I facing one problem regarding Advance Payment. We have a process to for making advance payment with reference to Purchase Order and Purchase Order Line Item. But system is allowing to post the advance payment amount more than the Purchase Order Value. I want to prevent this to happen. The system should not allow to make advance payment more than the Purchase Order value.
    Please help me on this issue.
    Thanks in Advance and Regards,
    Alkesh Mistry

    HI
    Please create the Advance payment request with PO number using sp gl indicator as F and then make the advance payment using the request.
    Regds
    Rajiv

  • Adding more than the recommenced RAM...

    I have an iMac 17in Flat Panel 800MHz with 256MB of Apple installed RAM (with an open slot for user installed RAM). The maximum recommended total RAM is 1GB. Can you put a 1GB pc133 144pin SODIMM in the user installable slot? Is this a bad idea to have the total RAM (1.25GB) more than the recommended total of 1GB? Thanks your your thoughts and suggestions.

    Is there another way to determine if the memory is really 512 but just not registering correctly with the imac, is it possible the mac doesn't display the correct memory or did I just get taken on ebay?
    Either that device is a 256 MB device or it is incompatible with your iMac and is being incorrectly identified as a 256 MB device.
    Either situation means that you need to return the RAM to the seller.

  • Hi from few days onwards i found one abnormality in my iphone4s .That is if i observe my phone settings screen from right side of the device top navigation appearing rightside height is more than the left side. In reverse manner from the left side.

    Hi from few days onwards i found one abnormality in my iphone4s .That is if i observe my phone settings screen from right side of the device top navigation bar appearing rightside height is more than the left side. In reverse manner from the left side. I dnt know whether it is default feature of iphone or not but i am really disappointed due to this. So please anyone help me in this issue and let me clear my doubt and make me happy. Thanks in advance.

    I believe what you are seeing is an optical illusion when viewing the screen from the side. Try to align one of the one of the options in Settings, like General, with the navigation bar you'll see it does the same thing.
    Hope that helps

  • Returns qty accepting more than the invoice qty

    Hi Experts
    When i am creating a sales order with reference to invoice the system is allowing to enter the quantity more than the invoiced quantity.
    suppose the invoice quantity is 100 when i create a sales returns system is accepting to do returns for 150 also whichshould not be and also it is allowing to do so many times with the same reference document
    i am getting just q warning message that for this invoice reference already returns exists if i bypass the warning message system is allowing to do next time also
    how to do
    any user exits to control which checks the VBRK number and VBRK billed quantity and it should less or equal to VBAK quantity
    regards

    Hi,
    Yes, unfortunately SAP does allow it.
    We are using FORM USEREXIT_MOVE_FIELD_TO_VBKD of MV45AFZZ to have our own validation for the same.
    I hope this helps,
    Regards
    Raju Chitale.

  • Hi, I need help with my iphone four bought in England but I live in Italy, I upgraded IOS six and now I can not read more than the Italian card, how can I contact a service center via email?

    Hi, I need help with my iphone four bought in England but I live in Italy, I upgraded IOS six and now I can not read more than the Italian card, how can I contact a service center via email?

    Only the carrier it is locked to can authorize unlocking it. Sounds like the phone was hacked to unlock it originally. Find out what carrier it is locked to, and look up their contact information using google or the search engine of your choice.

Maybe you are looking for