In house collaboration
Dear All,
I want to configure an scenario, in repetitive manufacturing, whichever moderate this situation:
I want to produce A, in plant 1000. In the BOM of A, it is an semifinish good, B, who is make in another plant 1200.
Supose I need for 2 pieces of B, for one piece of A.
How can I configure this situation thus, when I run MRP for 1000 pieces of A, in plant 1000, the system create an planed order for 2000 pieces of B, in plant 1200?
It's possible?
Thanks for your answers!
Marian
Dear
To address this issue please do the following : -
1.Keep SPK 80 in MRP2 view of the material master .
2.Goto -SPRO-MRP-Define SPK -Select 80 -Production in Alterantive Plant -Keep 1000 as Planning Plant and 1200 as Issuing Plant .
3.Create demand or Sales Order qty 1000 -A and run MRP -MD02-3,1,3,3,2 SO that it will generate Planned order of B-2000 pc in Plant 1200.Make sure that B is maintained both 1000 and 1200 plant .In case of Plant 1000 , B should have SPK-80 so that it will rtrigger Planned Order in Plant 1200 based on BOM set up .
Hope this is clear
regards
JH
Similar Messages
-
Setup of collaboration on external drive
Hi, I've been using os x since 10.0, but a newbie on server.
As an apple fan I've been drawn to the flame of thinking I could do more because apple makes it easy. So my interest in getting web side collaboration to support small groups with wikis, blogs, mail and calendar. I'm also interested in web apps.
My first install of 10.5 server was Standard and seemed to work, but...
When I got the mini I also purchased a FireWire external 500GB drive to house accumulated data and web development; the mini HD is small. I want the web stuff and new work housed on the external.
For this to work, Apple support said I need to go to Advanced configuration. I've read most of the entries in this forum on 10.5 server and can't thank you all enough for teaching me what to look for and how to read the docs. I have DNS working now fwd/back, Open Directory Master with Kerberos and LDAP directory running.
Set up the Web service with data to point to the external volume named ext/Library/Collaboration. Set up users and groups. Set up the website on the external under /Library/Webserver/domain. The static stuff works.
I set up the site domain to homepage on the external. I set up web service on the site to provide group (not user) wikis, blogs, maillist and calendar. I'm supporting small groups and don't need the individual user blogs. Groups with members was set up with Workgroup Manager and the groups enabled to use the domain for wikis, blogs, maillist and calendar. The groups are sticky in Server Admin and the correct domain is selected in Workgroup Manager. But no folders are created on the external in the /Library/Collaboration folder. When the group is enabled I should see something like Groups, Archived Groups and User folders created on the external drive. This is not happening. They aren't going to the startup drive either. Interestingly, since I haven't set up iCal service yet, there is a Documents folder created under /Library/Calendar/ folder on the startup drive. Which says something is happening. The logs indicate the system couldn't write to the external.
So I set up a share point to the external drive and even added the Everyone group to read&write just to see where the hang up was. No change. I thought this was a permissions issue. After trying different permission arrangements using Teamserver and Directory Admin I restarted and managed to lockout all logins including root.
As for trying server software, I don't think this stuff can be called user friendly yet.
I'm hoping someone has accomplished this small feat and can point me in the right direction.
Thanks,Whoopie -
Yesterday I was so frustrated. I got my dose of castor oil when for the second time I heard from apple support techs "If you haven't been to school and don't have prior experience 'Advanced Mode' is way over your head". OK, but they weren't willing to give my money back either -- so push on.
With tech support I set up a test group with full mail, calendar and web services. DNS is still confusing because it resolves inside and outside my NAT but doesn't locate the domain only the server. There is no domain A record. A server A record only.
Anyway, I used ditto to move the /Library/Collaboration folders and /Library/CalendarServer folder to the external drive. As I found out, the ditto command preserves resource forks and permissions.
i.e. sudo ditto -rsrcFork /Library/Collaboration /Volumes/ext_HD
just dumped the wiki folders and similarly the calendar documents folder onto the ext_HD (name of external drive) and they show up with the red circled minus sign.
I stopped the web, ical and mail services. Changed the data store locations for web service to /Volumes/ext_HD using the browse tool, and saved, then set the ical data store to the /Volumes/ext_HD/Documents folder and saved.
Started up mail, ical and web services one at a time. Had to use View and Refresh on the web service.
Reset the WGM web service and mail to the testgroup and voila!.
My wikis and group calendar came up and mail was passed successfully. I went to the file sharing panel browsing the ext_HD and there was a new item in the calendar and separately in the weblog folders after I made these through the web site.
I then set up a second group and nothing happened. I added the new group to the webservice for the site panel. I added a previous user to the new group and logged into the wiki with that, made a blog entry and logged out. The new group folder then showed up on the ext_HD and in the calendar/Documents folder on the external drive.
Mail and maillist also found the group wiki. Calendar events were stored as well.
Boy am I happy.
I hope this hasn't bored anyone.
Harry -
[All Platforms] New UI for On-the-Fly Collaborative Playlists
The idea came to me following a house party. There were four of us and we couldn’t decide whose Spotify playlist we should listen to. The decision was, as usual with us, to play one song per person. This didn’t work well either as only one device could be connected through Bluetooth to the stereo system at a time. Once a song finished there had to be a long wait for another song to start while one device disconnected from the stereo system and another connected, then all over again.. We gave up on the music all together in the end.
The next morning the solution seemed obvious to me. It would make things a lot easier if we could have a shared playlist. At the moment I know it is possible to share your own playlist with friends, but haven’t heard about one that can be created by several people at the same time in such an easy way.
The idea is simple, but in my view would solve the problem my friends and I had at the house party. It works in the following way:
Let’s say I want to create a new playlist that I could share with several people in the room. I create a playlist on the main device, call it ‘Alena’s House Party’. I then choose a list of people I want to share my playlist with (these would be people I follow already or another Spotify user that I can easily browse). A message appears on the personal devices of the people I have selected to accept the invitation. Once this is done a bubble (like the one in Facebook messenger) appears on all the relevant devices including the main device. This is the new Spotify playlist I have just created. Now my friends and I can browse our personal playlists and drag and drop the songs we want to add to ‘Alena’s House Party’. As a host, I get to review and sort the suggestions. Alternatively, to be absolutely fair, one song per person could be automatically selected from the list of suggested songs.
The plus of this is that it is easy to use. The bubble can appear anywhere on the screen on your mobile and you can sort your songs at any time, it also allows you to copy your favourite songs in the new playlist by dragging and dropping from various existing playlists on Spotify. And of course makes it easier to share music with your friends instantly and without a hustle.Hi, thank you for your reply. I have tried using 'Collaborative playlist'
feature as you describe but failed to figure out how it works. Am I correct
in thinking that by using this feature you can take an existing playlist
and and allow someone else to edit it? If so, I believe my idea is
different and certainly would be easier to understand and use. I am
suggesting a totally new playlist that would be created on the go. Say, I
add a few songs (could be from different playlists) and my friends can do
the same from their own playlists. The application would be easy to use as
all you need to do is drag and drop a song into a bubble, which is the
shared playlist.
Therefore, I wouldn't like the case to be closed. If you feel you need to
change the description, please do so.
Thank you -
Hiya in design experts....collaborative project...adobe stuff
Hiya you guys...
I know a few people who went from quark xpress offset stuff ( imagesetters etc ) to indesign ...when it became feasable to go from cmyk to rgb ....from offset work to 'in house' printing...years ago...
so I know a little about printing and tech stuff, but I am an old dog and what I knew is now museum info....
we are trying to get a collaborative project going in the premiere pro 'lounge' area.. using adobe products... come up with a cool 'product' ...and if you check out the threads please join us in lounge for fun..and a ton of work.. .cause the deadline is looming.. OMG...
I dont get email notifications from threads so pls join us in lounge...I chk that every five minutes it seems.. as I'm retired and chomping at bit to do stuff...
http://forums.adobe.com/thread/1315028
http://forums.adobe.com/message/5759201#5759201
thanks a ton!
dont forget.. guttenberg (sp? ) had some very good criteria for print and design back in the 1500's... so you know.. lets make him proud...Almost. The guy was named Gutenberg. http://de.wikipedia.org/wiki/Johannes_Gutenberg
-
Okay. We have three Ipads in our house with only one Itunes account. When I go into imessaging and facetime on each of the devices, it wants to start switching my wife's cell phone and then the three emails associated with each Ipad to the contact information for all of the Ipads. As of this morning, only the imessaging and facetime are turned on my wife's iphone and ipad. My kids imessaging and facetime is turned off. Do you really have to have an itunes account for each device to make then work??? Any help would be very much appreciated.
RyanThere is only one solution. Each user must have their own separate user account. All of their respective data would be contained in their separate user accounts. This also means each will have a separate iTunes Library. If you all use the same third-party apps, then each will have to purchase their own copies under their own Apple IDs. Some data sharing is possible. See:
iTunes- How to open an alternate iTunes Library file or create a new one
iTunes- How to share music and video
iTunes- How to share music between different accounts on a single computer
iTunes- Setting up Home Sharing on your computer -
Hi,
this is my first time on the support board, so hopefully I'm doing this correctly. We have 3 desktop computers in our family, which are wired in with ethernet cables. We also use the cables with our laptops (we have various connections throughout the house) I have an iphone, and an ipad, my boys have ipod touches. I purchased an airport router to use when I'm using my ipad, etc. The boys and I would like to be able to share apps that we have purchased. I'm wondering if there is a way to use home sharing in our situation.
thanks!Have a look here...
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l -
Multiple users, devices & Apple IDs in the house. Can we, and how would we, use Home Sharing?
We have three users in the house, each with their own Apple ID, using multiple mac/PC devices. Can we and how would we use Home Sharing to share music, apps, etc?
Do you have a computer. You can't share music or apps from one mobile device to another. To share photos you need to use photo stream shared albums.
-
I want to buy a new apple tv but it used hdmi cables and my house is only wired for analog. Is there any way I can use the apple tv on analog cables?
Welcome to the Apple Community.
It's do-able, but I don't think it's a great idea.
DVI
Some users with DVI have managed to get their TV's to work with DVI-HDMI cables. DVI carries no audio, so alternative connections need to be explored to enable audio. DVI doesn't necessarily support HDCP as well as other standards used by HDMI (which may or may not be an issue)
Analogue
There are hardware converters that will convert HDMI to various other types of output, however there are some issues with doing so that you should be aware of.
HDCP
HDCP compliant converters will not allow you to watch HDCP protected content such as that from the iTunes Store. Non compliant converters exist but we cannot discuss them under the Terms of Use for these communities.
Resolution and aspect ratio
I'm not aware of any converters that will scale the output from the Apple TV, any TV or projector which is used will need to be widescreen and support resolutions of 720p (Apple TV 2), 720p/1080p (Apple TV 3)
DAC
DAC (Example Only - Not a recommendation or suggestion that this is suitable in your circumstances) -
At a loss. Wiring a possessed house I think! Input needed
Need some help.
I know and have done a lot of networking No pro, but self taught. Did run Ethernet of my whole house (ex wife's house now ) pre wifi days. Running wires, using switches and routers. All worked. Have down a ton of wifi - all Apple gear for myself in my location, friends and family. Good to go. I currently run a bunch in my home for iPhones, computers, netflix, itunes server, Air Video for all devices. Flawless.
So I'm not a dummy at least. So……
To my dads house. My on going project for a year. Great house. Big. Hand built back in the '50's. All plaster. Well made.
1- His office - cable modem to Airport Extreme - named BASE. Across this room, one Airport express (all AX are older g units) for the stereo from computer.
Now when I try to extend this network only for him to use his iPhone with Apple Remote to control music, I have now bought 5 Airport Expresses - the signal will not carry for more than 10 feet at best in this house (it's possessed I swear). NOT KIDDING.
I put an Express 10 feet from the office to a kitchen, why because any further I get no signal connection.
From this Express another one 10 feet for a den.
But the signal is so weak it doesn't work.
The house is plaster - I guess very well plastered and who knows what metal lathering is behind the plaster? It's a ranch.
What could possibly abort wifi signal like this. Oh, I might add, no iPhones work in the house either. We're in NY.Long Island. Major ATT signal. Nada in house. Go outside no problem.
So I'm going to tackle this again this weekend. Start from scratch. Any insight? I'm asking because I'm at a loss and think I'M NUTS! LOL
What would make wifi not carry for any distance? Lot's of windows in the house too.
I'm on the verge of telling him to have cable run another wire and modem to the other side of the house.
I'm stumped. I was going to post a few times but can't imagine why I can't get this working. Feel like a dunce.
Right now he tells me it's no connection in the den. The last AX extender not 10 feet from him.
Thanks in advance.In addition to metal, water also will cause significant reduction in signal. The higher the frequency, the worse the problem. (One of the reasons why in the past submarines needed to surface to use their radios.) Perhaps the plaster or wood is exceptionally wet or the particular plaster they used has a high metal content. You may want to try using only 2.4GHz instead of 5HGz because lower frequencies penetrate walls better. I'm grasping for straws, but I'm not sure what else you could try short of tearing down walls.
I will tell a story of one wiring job I did. My boss gave a quote and approval sight unseen. He normally didn't do this but due to various circumstances and time constraints, he took a gamble. The job was to install a DSL modem and wireless router for a doctor's office. The modem and router were in the managers office. The reception area in the next room would have two workstations about 15 feet away, connected wirelessly. The doctor's office would get one laptop connected wirelessly, about 100 feet at the other end of the building. The building was all wood construction so no one foresaw what happened next. The manager's computer was fine since it was wired. One of the wireless reception workstations was fine with full signal strength since it was a line of sight through an open doorway to the router. The other reception workstation was working but only had 50% signal strength. (Not line of sight to the router.) The doctor's laptop had zero bars. I moved the laptop next to the router and got 100% signal strength. I walked the laptop next to the workstation with line-of-sight, and still got 100%. I walked to the other reception workstation and got 50%, same as the workstation. I walked out of the reception area turned left and started to walk down the hallway to the doctor's office. I took no more than 5 steps and got zero bars! I walked back a few steps and the meter jumped to 50%. I had to do this a few times to fully convince myself. It was only a chance conversation I had with one of the nurses who recalled that the former occupant of the office was a dentist. So we surmised that the room that the router was in might have had the x-ray machine, so they would have lined the walls with lead or whatever. In any case, we ended up having to pull wires. But we learned that regardless of what it looks like on the outside... But this does sound quite similar to your experience.
There's also the time that my coworkers found that the whole wall was 1/4" steel plate. The walls were covered with drywall so we didn't know it was there until we ruined a half dozen drill bits. It seemed like it was armor plate steel. We think the building used to be a indoor gun range or something. And there was the time that we encountered hardened concrete walls at an office using a former military building. Fortunately neither of those had Wi-Fi but we likely would have had signal problems in both cases. It taught us that we can't assume and needed to do a thorough inspection ahead of time.
So while I don't think the house is possessed, I do suspect that the original builder used some funky local material. Maybe he was a conspiracy theorist and has tinfoil in all the walls. -
Is there a way of working collaboratively on a flex project with a small project group?
Is there a way of working collaboratively on a flex project with a small project group?
I am part of a small group of developers who wish to work on a single flex project together. Is there a way to set up flex so that the project can be developed by multiple people at the same time. I have seen one thread out on the internet about working locally and then uploading to SVn but this is not an option in this case.
Any ideas.
Many thanks in advance
DaveI would say that rushing into development without a source-control system will cost you more in the long-run. If your organisation is serious about developing software it then it needs to invest in the necesary infrastructure, so you should get that process kicked-off as soon as possible.
In the interim you could set-up a source control server on one developer's machine or commandeer a spare machine to use as a temporary source control server. Just make sure you have it backed-up regularly. Or you could use one of the online source control services; many will support private repositories for a small fee. -
How to access a specific tab in collaboration server - via scripting
So, I want to be able to show a link in a portlet to a user such that when the link is clicked it takes the user to collaboration server and automatically sets them on the discussion tab...any ideas? do transformer tags work in this case? any other ways?
ThanksQuickKeys may work, or you can look on http://www.versiontracker.com or http://www.macupdate.com for other alternatives.
Another option is to create aliases to those folders and store the aliases in a local folder which you can place on your Dock, the Finder window sidebar or toolbar. -
I'm hopefully getting an iPhone 5 soon, & I'm just wondering if I could get a different carrier for the phone because I heard that AT&T is more expensive than the other carriers. At my house (for our computer & TV) we have AT&T. So, I'm just wondering if I could get a different carrier for the iPhone instead of AT&T.
The iPhone is avaialble in the U.S. with the following major carriers:
AT&T
Verizon
Sprint
T-Mobile -
I just had to reformat the external hard drive that houses my iPhoto library, then restore it from a backup. Now Time Machine is telling me my backup hard drive suddenly does not have the space to complete a backup. I also noticed when I go in to Time Machine, there are only about 5 backups recorded on the ext. hard drive. There were many more before. Any idea what happened and if I have to buy a new back up hard drive?
Hallo Kieth ,
I am not quite ready to restore the full iphoto library , as I have days of work re - imputting titles,descriptions and enhancement . I hope that your suggestion works , as I use my Macbook basically to work with digital photography. Through time , I will need to delete my library to recover more disc space and I would hate to have to spend more time re - imputting titles and descriptions all over again .
Thanks for your interest and advice.
regards - Alan -
I just recently purchased a iPhone 4. I am using it as Prepaid for Verizon. I only get a certain amount of data time, and was trying to use the wifi at my house in order to do somethings online without using my prepaid data, but for some reason it will not pick up the wifi at all, and when i try all the different things I have been told to try it still does not work, how do I get the wifi to work?
You didn't say what you have already tried, but if you haven't already done so, power-cycle your router (unplug it for 15 seconds then plug it back in), then on your phone go to Settings>General>Reset and tap Reset Network Settings, then try joining your wifi again.
-
HP Officejet Pro 8600a all of a sudden is not recognized by only my computer in the house
Hi, I have 4 laptops in my house. We have all been connected wirelessly to my HP printer for over a year. All of a sudden, for some reason, my computer no longer sees the printer. I have an ASUS. I run Windows 7 with Windows Firewall. My router is a 3 month old Linksys EA3500. I can print from every other printer in the house, and I can also print from my Android Phone. However, when I try to print from my laptop, it now says that it is detecting printer has been turned off. I have done everything I can think of to fix this. The only changes I recently made were installing Webroot AV program. I can't be 100% certain, but i'm pretty sure I have printed since that installation, and all of the other computers on my network are using Webroot as well with no issues. Hoping for some help. Here's what I've done so far:
Tried troubleshooting printer via computer. It's gone through the spool service check and whatever else the standard troubleshooting does. It said something about my printer being turned off. It definitely was not, but I unplugged and restarted just to be sure. No fix.
Noticed IP changed on printer and thought maybe something with static vs dynamic (don't know much about this) so went to "update IP address" on my laptop and updated the info. Checked the router settings info by entering printer's ip in browser. Printer shows connected and ready and all looks good. I pinged the ip and got results. Mac filtering is not enabled so I don't need to deal with that. SSID is not hidden. The 802.11 configuration says that the network type is WPA-PSK with WPA2 and AES selected for encryption. Same as it always has been.
Double checked to make sure printer was recognizable by my firewall. It is on the accepted list.
Last resort: I uninstalled the printer software and deleted the device from my laptop. Attempted reinstall, but when it gets to the part where it's supposed to search for the printer it says unable to find. I enter the IP address from the printer and it still cannot find. I enter the host name and it still can't find. Since I uninstalled everything, I can no longer install the printer at all.
Went to drivers on line and tried using the install via online option. same results. "unable to find printer".
I unpugged the printer from the wall again, this time for over an hour, hoping it would reset but realizing this probabaly isn't the issue since every other laptop can print in my house.
Tried to connect ethernet cable and install printer that way. Plugged one end into router and other into printer as directed on troubleshooting tips. Ran Disk software and it doesn't install the printer. IP address changes on printer when I use ethernet and I am entering new ip accordingly.
Reset my modem and restarted. Reinitialized my router and then used the software to reconfigure it. did the standard 'wait ten seconds and plug everything back in and reboot computer'. No fix.
Checked my wireless network adapter setting to make sure I have most updated drivers. I do.
Deleted every single thing that relates to my printer in every folder and in regedit.
Tried reinstalling printer both wirelessly and with ethernet. Still unable to find printer either way.
I have changed no settings that I can think of since the printer last worked a few weeks ago. As I said, every other computer prints perfectly. The only thing I can think that's different is that all the oher laptops are running Windows 8 and I'm still on 7, but that didn't matter before, and I can print from the HP print software on my phone.
Please somebody tell me what I'm missing here. I'm going bonkers. Thank you so much to everyone who takes the time to reply on this support forum.
This question was solved.
View Solution.Well you have done quite a bit. Let's try here if you haven't.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02915280&tmp_task=solveCategory&cc=us&dlc=en&lc...
Then let's give this a shot.
These settings are for setting up your wireless printer to stay connected to your router, keep wireless devices better connected and makes your router secure and hack proof.
1. Set a static IP in the printer (click here) outside the DHCP range of the router (check your manual).
This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this
first if needed. More Wireless Printing help is here (Windows solution 4, static IP).
2. Verify in the printer that 'Auto Off' is disabled. Use the Embedded Web Server (EWS) by going to the
printers IP address in your browsers address bar, click Settings Tab/Auto Off. Or use the Printer
Assistant, Printer Home Page (EWS).
3. If the printer supports and has IPv6 enabled, turn off IPv6 in the printer.
4. If needed and you assigned a static IP address, try using 8.8.8.8 for the Manual DNS server and
8.8.4.4 preferred DNS server.
In the router: (Refer to your router manual for information)
5. Use a fixed wireless channel like 1, 6 or 11, never 'auto', try channel 1 first then the rest.
6. Set router to 20Mhz only, or 145Mbps depending on router.
7. Always use WPA2-AES (Personal) encryption, but you can try ‘mixed’ mode.
8. Disable WPS and never use it and disable UPnP for the routers security. Nobody can hack your
system now and helps with wireless connectivity (if you want to know why, search the web).
9. If you have a dual band router (2.4Ghz and 5.0Ghz bands), make sure the SSID’s are NOT the same,
they must be different for all bands, even for any Guest networks.
10. SSID broadcast must be enabled.
11. Save all settings. Power off both, wait 2 mins. Power on router wait 2 mins.
12. Power on printer and verify it reconnects to router.
Windows 7/8/8.1 Is Network Discovery on or off?
Control Panel/Network and Internet/Network and Sharing Center/Advanced sharing settings.
Under Home or Work (current profile) / Network Discovery.
Select "Turn on network discovery" and save changes.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!
Maybe you are looking for
-
Error message with a hyperlink attached to it
Hi Friends I have a requirement wherein I need to display a hyperlink along with the error message in webui. Example... Please enter a valid currency Details Here Details should appear as a Hyperlink and on clicking on this hyperlink it should naviga
-
Sync.me application not working
the application "sync.me" was working properly i removed the application "sync.me" and i reinstall it from my new apple id the application is not working when i opened it it close directly
-
Just set up iTunes for windows but when I try to sync my iPhone to it this is what it says, I have another iTunes library on my power book. It than asks if I want to erase this iPhone and sync with this iTunes library. I used the same password on thi
-
I have Virtual PC 7.0.2 running on an Emac with OSX 10.4.3. I cannot log into Windows XP as I get the following message: "The system cannot log you on now because the domain DomainName is not available" Has anyone had this problem and found a way aro
-
Dimension that mention Sales Promotion Girls
Hi experts, I have needs to generate report in OBIApps that show Top 10 New Contact Generating by Sales Promotion Girls (SPG). May i know if in Marketing Analytics, is there any dimension that specify data of SPG? I have already searched in W_EMPLOYE