In need of your assistance please, for HP pavilion DV6 7007tx

Hello,
I previously updated my bios into Insyde F.24 (see attached images) which was ok at first, but when i decided to update my graphics drivers to its manufacturers driver (Nvidia), I started to experience my HP Pavilion DV6 heating up whenever i play games.
I often check and put my graphics setting to balanced in hopes to lessen the heat up a bit.  However as soon as i play or open up a game (Fable 3, mass effect 3 and others) the fans starts to spin wildly.  To prevent my notebook from overheating i decide to exit my game after 30 minutes of playing and let it cool down first and start again.
I read some points that the update in Bios i made previously possibly has something to do with it, and am now asking your assistance if i can downgrade or roll back into my previous or original Bios.
Would it possible to downgrade?   My current Bios version is Insyde F.24.  I also searched for a Bios update at HP website and found out the current version i should be running is F.0A.  Should i run this?  
Any kind suggestion i must do?
Kindly check my notebook info on below images.
Thank you alll in advance.
Regards,
Edgar Duenas
learning and adapting.......

Hello,
Is there not anyone whose kind enough to assist me on this?   Please do help for anyone who knows a countermeasure.  Thank you all in advance.
Regards,
edgarduenas
learning and adapting.......

Similar Messages

  • Need Win 8.1 drivers for HP Pavilion dv6-6121tx

    Now i am using Win 7 in my HP Pavilion dv6-6121tx laptop,now i plan to upgrade Win 8.1 ,so i need all the drivers for it ,please help me

    Hi
    >>before updating the windows 8.1 please chk for the hardware requirement
    >>after installing the windows 8.1 most of the drivers will be updated
    >>if still dosent work go the link Drviers and put your product number
    >>if your laptop has the drivers you can download
    Please click "Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
    Click the "Kudos, Thumbs Up" on the bottom right to say "Thanks" for helping!
    I am an HP employee

  • I need recovery for laptop Pavilion dv6-1235ee

    I need recovery for laptop Pavilion dv6-1235ee , I need the link for the recovery or send recovery cd to my mail 

    If you have the recovery partition intact on your notebook, you can just press F11 during boot and it will take you to the recovery mode. Just follow the instructions to perform a recovery and it will reset your notebook back to the factory settings.
    In case you do not have the recovery partiion, I would advise you to go through the following document which will help you resolve the issue:
    http://h20000.www2.hp.com/bizsupport/TechSupport/D​ocument.jsp?objectID=c00810334
    Hope this helps!
    Although I am an HP Employee, I am speaking for myself and not for HP.
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

  • How can I get a repacement battery for my pavilion dv6: 484170-001?

    I need replacement battery for hp pavilion dv6 with number 484170-001

    OK this is a volunteer Forum and most of us do not work for HP and some of us are across the pond where there is a time difference so sometimes there will not be an instant response. 
    Genuine from the U.K.:
    http://www.ebay.co.uk/itm/Genuine-Laptop-For-HP-484171-001-485041-001-485041-003-484170-001-513775-0...
    http://www.ebay.co.uk/itm/GENUINE-BATTERY-FOR-HP-PAVILION-HP-Spare-484170-001-/371083992849?pt=UK_Co...
    If this is "the Answer" please click "Accept as Solution" to help others find it. 

  • How to download drivers and software for hp pavilion dv6-3127tx . product unable to search

    How to download software and drivers for HP Pavilion dv6-3127TX. Unable to search the product in help and support center.
    Mohan Singh

    Hi,
    I can't find a listing for this model either, but you should find the drivers available on the link below work.
    http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=4331848&lang=en&cc=us...
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Where can I get a motherboard replacement for a Pavilion dv6-3020us laptop?

    Where can I get a motherboard replacement for a Pavilion dv6-3020us laptop?

    Have you tried to clean vents with compressed air.
    Some other propositions below:
    Check the link below:
    How to prevent and deal with overheating.
    Try to solve problem with audio by using intrcutions form the link below:
    Use Hard Reset to Resolve Hardware and Software Issues
    Note:
    Do this for 1 minute instead 15 seconds.
    ** Say thanks by clicking the "Thumb up" icon which is on the left. **
    ** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

  • Is it Possible to change the DVD drive to Bluray for HP Pavilion dv6-6176sx

    Hi All,
    Is it Possible to change the DVD drive to Bluray for HP Pavilion dv6-6176sx Entertainment Notebook PC?
    Thanks
    This question was solved.
    View Solution.

    Sure it is not even very difficult. Do you just need a BR reader or a burner/reader? The replacement disk drive will be $80-120 or so, maybe a bit less. You can find them on eBay. You can use a generic one but that may require some reworking of the faceplate or just get an original dv6-6000 BR drive on eBay. Swaps out with a couple screws on the bottom; slide out and slide in the replacement. You will need new software to play BR movies, of course.  
    Post back with any questions

  • Drivers for LW261UA Pavilion dv6-6110us

    I did that but I still have VGA hardware issues, cannot connect to the internet. please help. I have been trying for days!!!

    http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-dv6-Entertainment-Notebook-PC-series/5082212/model/5128756#Z7_3054ICK0KGTE30AQO5O3KA30R1  For this Install the Ralink 802.11 b/g/n WiFi Adapter from the above link Network Controller Hardware ID:
    PCI\VEN_1814&DEV_5390&SUBSYS_1636103C&REV_00
    PCI\VEN_1814&DEV_5390&SUBSYS_1636103C
    PCI\VEN_1814&DEV_5390&CC_028000
    PCI\VEN_1814&DEV_5390&CC_0280
    _____________________________________For this Install the Realtek Local Area Network (LAN) Driver from the above link PCI Device Hardware ID:
    PCI\VEM_10EC&DEV_5209&SUBSYS_358E103C&REV_01
    PCI\VEM_10EC&DEV_5209&SUBSYS_358E103C
    PCI\VEM_10EC&DEV_5209&CC_FF0000
    PCI\VEM_10EC&DEV_5209&CC_FF00
    For this Install from this link
    http://support.lenovo.com/us/en/downloads/ds030147 SM BUS CONTROLLER PROPERTIES HARDWARE ID:
    PCI\VEN_1022&DEV_780B&SUBSYS_358E103C&REV_13
    PCI\VEN_1022&DEV_780B&SUBSYS_358E103C
    PCI\VEN_1022&DEV_780B&CC_0C0500
    PCI\VEN_1022&DEV_780B&CC_0C05For this install HP ProtectSmart Hard Drive Protection from the above link UNKNOWN DEVICE
    ACP\HPQ0004
    *HPQ0004  Hope this helps, for any further queries reply to the post and feel free to join us again  **Click the White Thumbs Up Button on the right to say Thanks**Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. Thank You,GBL84Although I am an HP employee, I am speaking for myself and not for HP

  • Blue screen with error code and I have no recovery disks for HP Pavilion dv6-1260se

    I have a HP Pavilion dv6-1260se with factory installed operating system of Vista. When booting up the computer, I receive a blue screen with this error message: STOP:  c000021a {Fatal System Error}.
                                                                The verification of a KnownDLL failed.  system process terminated unexpectedly with
                                                                 a status of 0x0000221  (0x007fb9c0  0x00000000).
                                                                 The system has been shut down.
    I do not have recovery disks for this computer.  I tried to order them but them seem to not be available.  This is my daughter's computer.  She says she started to have trouble after downloading Frost Wire (music share) and then she removed it.  We tried going back to an earlier time and that didn't help and then the blue screen with error message appeared. What do I do now?
    This question was solved.
    View Solution.

    Hi,
    Assuming your in the US, recovery discs are available to order for that model here.  That may be the best option.
    You should also be able to do a recovery without the discs as well.  Take a look at this document: Recover Windows Vista Operating System Using HP Recovery, and look for the section Restore the PC to its original condition with the HP Recovery Manager if Windows Vista is not accessible.  This should allow you to recover the PC.
    R
    Although I am an HP Employee, I am speaking for myself and not for HP.

  • What is the latest motherboar​d for a Pavilion DV6-2020ev​?

    Hi, my motherboard on my Pavilion DV6-2020ev failed due to overheating. The current MB part number is  "574902-001"  followed by "7F0994". The processor is an i7 (1.6Ghz). Instead of getting the same board, I was wondering if there was a later MB that can work. Does anyone know? Unfortunately the dealer cannot help and will only replace with the same part number -(
    thanks,
    arjogie

    The motherboard listed is the right one listed for dv6-20xx notebook. Just ensure that you download the latest BIOS update for your notebook from the software and driver download page on www.hp.com once you have replaced the MB.
    Although I am an HP Employee, I am speaking for myself and not for HP.
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

  • Hi all, i need urgently your help please. My touch screen on muy Iphone 5  is not working, i dont understand as it has not been damaged at all, i dont know what happened and need urgently somebody helps me please

    Please anyone there can help me what I can do??!! touch screen of my Iphone 5 is not working at all and dont understand as it has not been damage and it is only 2 months and half!! it is not an old iphone and it has not been damaged, has happened right now and cannot turn off the mobile at all. Tried to take out the nano sim as i though it will be turned off but it has not been! i dont know what i can do and i am desesperate!!! thanks All for your help!!

    Removing the SIM has no affect on the power of the phone. It is just the part that facilitates connecting to your carrier. Try holding the sleep/wake and home buttons together until you see the Apple logo on the screen and then release the buttons. The phone should reboot. You may need to hold the buttons together for 15-30 seconds.

  • Tecra M10 cmos battery was disconnect​ed and now laptop is bricked. Need EC/KBC assistance please

    Hello,
    I had to do a repair on my audio board and unfortunately I had to disconnect the cmos battery and remove the motherboard to do the repair. Now once powered up the "on" light will blink once green followed by 2 orange all day long and nothing else happens (the fan does run full speed). I downloaded the service manual and found I will need to use an EC/KBC disk to repair the bios via an external floppy drive. I have had no luck finding any such disk or info. The display is totally blank. Any help would be greatly appreciated. The model is a Tecra M10 - PTMB0A-00M001

    You're more than welcome. I'm sorry I'm not going to be able to help you with the specific detailed instructions you need to resolve your problem. But, I hope I can point you in the right direction.
    First off, Toshiba uses various makes of BIOS in their notebooks like Award, Insyde, etc. In fact, they even use various makes of BIOS for specific individual models. So, trying to figure out your BIOS make, from the name on the BIOS chip would help.
    Next, download the latest BIOS version for your model and OS bit combination. Like BIOS v.3.3 for Windows 7 64bit. Sometimes the BIOS upgrades are OS specific, sometimes they're not. Download the file to its own directory on another computer. This may be a zip file, or an exe file that is actually a self extracting - self installing BIOS update. Next, use winrar or jZip or a similar program and extract all the files in the archive. This might be a 2 step process, eg you download a zip file and extract all the files only to find one exe file. In that case, run the archive program again on the exe file, and extract all its files to their own directory.
    The files you'll need from the above should *.com files inside a sub-directory called BIOS.
    Next, you need to try to find a 'bootable' BIOS update program for your make of BIOS, like an Award BIOS update USB or disk bootable program, ie NOT a Windows based update program.
    Then, you can trying surfing around for the specific instructions to help you out. Try surfing these links or for something similar:
    BIOS Recovery Procedures
    INSYDE BIOS Recovery Method
    Or you might want to consider paying a certified Toshiba tech a maximum of one hours labour to try to recover your BIOS for you.
    Toshiba Australia Service Centre search page
    Let us know what happens. Good luck.
    Mike

  • "Tesserax" I Am In Need Of Your Assistance

    Ok so i'v been reading enough to know "Tesserax" is the guy i need to talk to so lets get down to business, shall we?
    My Steup:  2 Foscam FI8905W 's Airport Express connected via Cat 6 Cable From There I Have it connected to my Airport Extreme Base Station that is connected to the Modem *Takes Breth*
    My Configuration For Airport Express:
    My Configuration For Airport Extreme:
    My Problem: The Cameras Work When Connected To The Airport Extreme but when connected to the Airport Express they do not show up on ip Camera Tool and i cant connect to them.
    My Questions:
                            A.) What could be causing this?
                            B.) How do i fix it?
    Thank You In Advance
    -Brian

    1  10.0.1.1 (10.0.1.1)  1.540 ms  0.870 ms  0.746 ms
    2  192.168.0.1 (192.168.0.1)  4.256 ms  2.066 ms  2.780 ms
    That.....is a double NAT error.......I am sure that LaPastenague will agree......two devices both trying to perform as routers on the same network.
    Port forwarding/mapping will not work correctly in this type of setup.
    The TC needs to be in Bridge Mode to operate correctly on the network. See screenshot below.
    Port forwarding settings need to be configured on the M1000. This Century Link support document / guide should help:
    Port Forwarding | Actiontec M1000 | Modems - Internet Help

  • Photoshop CS3 need image rollover assistance/save for web

    I just installed Photoshop CS3, was disappointed to see ImageReady gone but not worried.
    I updated an old rollover file with new wording and went to save the slices as I had always done in the past - with ImageReady, it would automatically save the file as a standard name (file.gif) and the rollover type (file-over.gif)
    Unfortunately, I can't figure out how to do this in CS3 without ImageReady. I bought the design premium version so I don't have Fireworks. Does anyone know how to do this process in PS CS3?

    Misty,
    PS CS3 doesn't support rollovers. So you have to:
    - recreate rollover effect in Photoshop
    - save "over" version of your image under different name
    - recreate rollover code in Dreamweaver or other HTML editor

  • What DVI-D cable please for HP Pavilion?

    I have just bought a new Pavilion 500-250ea desktop + Pavilion 22xi screen.  Unfortunately the description 'desktop' seems to have been taken too literally by HP <g> - once the PS was in its storage under the desk, then the DVI-D cable supplied with the monitor was too short to reach it, so I shall have to buy a new longer one  :-(
    Both PC and monitor have dual-mode DVI-D sockets, but the supplied cable was just a single mode DVI-D. Does either/both device(s) actually support dual mode, or will single mode be sufficient for the new cable?

    As your HP Pavilion 22xi IPS LED Backlit Monitor only supports up to 1920 x 1080 resolution, a DVI-D single link cable is sufficient for your application.
    If you have any further questions, please don't hesitate to ask.
    Please click the White KUDOS "Thumbs Up" to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Maybe you are looking for