In P6 EPPM Application page p6 Help is not working

Hi Guys,
We have configured the P6 EPPM application successfully.
Currently the p6 EPPM application is up and running.
Our requirement, is in the P6 Application right corner in help link we have to get the p6help page.
For this we have manually deployed the p6help.war file in Weblogic server and its state shows "ACTIVE" in the control tab and in testing tab its shows the default url:http://hostname:8203/p6help
But when we try to access this url we are getting the below error we also tried with below url too
http://hostname:8203/p6help/help
Error 403--Forbidden
From RFC 2068 Hypertext Transfer Protocol -- HTTP/1.1:
10.4.4 403 Forbidden
The server understood the request, but is refusing to fulfill it. Authorization will not help and the request SHOULD NOT be repeated. If the request method was not HEAD and the server wishes to make public why the request has not been fulfilled, it SHOULD describe the reason for the refusal in the entity. This status code is commonly used when the server does not wish to reveal exactly why the request has been refused, or when no other response is applicable.
Can you please suggests us to fix this issue.
Regards
Athish

Hi Athish,
The only thing i can think of in the link you pasted is it has https instead of just http (i'm assuming you did put the real servername in).
You could maybe try using the IP Address instead.
Failing that try creating your own domain for it and see if it works like that.
I haven't tried deploying it under a managed server nor do i let the P6 installer do any of the weblogic configuration so it could be something in the way it is deployed that is different than just creating a new weblogic domain with an AdminServer.
Is there anything showing in the log file? Either P6 or Weblogic (you may need to set the logging level to debug)
Regards
Alex

Similar Messages

Photoshop CS4 Extended ...Program's 'Help' does not work

I have PS CS4 Extended ... the Help command does not work ... I get a message saying "there was an error launching th eAdobe Help application. You may need to reinstall the application and Help component.
IK have un-installed the program completely and then reinstalled it. Still, the Help does not work, although the rest of the program seems to perform ok.
I'm rather at my wits end.
Has anyone any suggestions.
Thansk.

This won't fix your problem, but it might help as a workaround...
This is the page that normally opens when you click Help - Photoshop Help... in Photoshop CS4:
http://help.adobe.com/en_US/Photoshop/11.0/index.html
-Noel

PSE 10 and Adobe CS6: When running silent install help is not working afterwards

Hello,
I'm not sure if this is the correct forum. If not: Please help me find the correct one.
I have a big issue with Adobe CS6 (and former versions like Photoshop Elements 10): When installing it from DVD running GUI everything is working fine afterwards. If I install e.g. Photoshop Elements 10 using "Silent Installation" help is not working afterwards. It states that it cannot locate the URL. I have not installed AIR and also do not plan to install it.
I have 'played' a little around with Common Files\Adobe\helpcfg and help directory. Now at least I do not get an error message but still it's not the online help which opens in the browser but the web page that is defined as 'home'.
The same I see now in Adobe CS6. I have e.g. packaged After Effects and Illustrator and when deploying it I'm not able to open help as well and I fear that this is the same issue.
Has anyone deeper knowledge about how "helpcfg" is working? Any example files? Any other help appreciated as well.
Kind regards
János

@hannilator Have you checked the exceptions folder contents for instructions on how to push to logged off computers? Here's what I get when I package CS6 (DesignWebPrem) and excude AIR/CHC:
After you have deployed the package, separately install the products in the exception folder.
IMPORTANT: Before you install the products in the exception folder, refer to the following Adobe Knowledgebase article for information on installing these products and configuring the settings correctly:
http://www.adobe.com/go/aamee_exceptions
NOTE: The installation commands provided below will work when the user is logged in to the client machine where the package is being deployed. For the scenario where the user is not logged in, prefix the following string to the command:
sudo launchctl bsexec `ps auwwx |grep [l]oginwindow | awk '{ print $2 }'`
As an example, here is the command to install "Adobe AIR" when the user is not logged in to the client machine (assuming Adobe AIR is part of the package):
sudo launchctl bsexec `ps auwwx |grep [l]oginwindow | awk '{ print $2 }'` Adobe\ AIR\ Installer.app/Contents/MacOS/Adobe\ AIR\ Installer -silent
###################################### Command to install Adobe Dreamweaver Widget Browser ######################################
Adobe AIR Installer.app/Contents/MacOS/Adobe AIR Installer -silent -eulaAccepted -programMenu WidgetBrowser.air
###################################### Command to install AdobeHelp ######################################
InstallAdobeHelp appVersion=4.0.244 appId=chc pubId=4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 installerArg1=-silent installerArg2=-eulaAccepted installerArg3=AdobeHelp.air

Help is not working in Hyperion System 9 WebAnalysis

two months back we have installed Hyperion System 9.2.0.3 BI+ server and is working fine. however recently one user complained that WebAnalysis help is not working. we are getting "page cannot be displayed" when clicking on Help --> contents and index from WebAnalysis -- <a target=_blank class=ftalternatingbarlinklarge href="http://hostname:19000/WenAnalysis">http://hostname:19000/WenAnalysis</a> this is the direct link to the webanalysis help <a target=_blank class=ftalternatingbarlinklarge href="http://hostname:19000/workspace/docs/en/wa_user/frameset.htm?/workspace/docs/en/wa_user/launch.html">http://hostname:19000/workspac...n/wa_user/launch.html</a> Do you know how to fix this?

Hi Friends,
I am working on Sandbox Server, in that Help (F1) is not working. When i try to click F1 system is opening the popup and showing the following message-
The page cannot be displayed
Plz help
Regards
Goutham

F1 help does not work in transaction SE80

Hi Experts!
A strange error occurred in our ECC 6.0 SR3 system (Windows 2003 SE 64 bit based, MaxDB 7.6.03.009). F1 help does not work in transaction SE80. Either nothing is shown when a keyword as SELECT is marked and F1 key is pressed, or a strange popup appears with title u201CABAP Keyword Documentationu201D and root u201CHit List of Index Searchu201D - [screenshot|http://i43.tinypic.com/aox7d.jpg]. No matter what I choose in the tree it always closes, no help is displayed and SAP GUI returns in the main screen in transaction SE80.
I found this thread [Re: SAP F1 Help and SE80 issue|Re: SAP F1 Help and SE80 issue] but it did not help me. This is my system information:
SAP PC VERSION INFORMATION: saplogon.exe
MAIN MODULE INFORMATION:
   saplogon.exe
   SAP Logon за Windows
   Final Release 710
   7100.3.12.1042
   1046700
SYSTEM INFORMATION:
   Operating system: Microsoft Windows XP 5.1 (2600) Service Pack 3
   Internet Explorer v. 7.0
Application help works perfect - I checked the configuration in transaction SR13 too.
Any ideas will be appreciated!
Thanks!

Hi Presu,
As it is seen from my previous post SAP GUI version is 7.10 SP 12. I downloaded the last SP 13 and installed it. Now SAP GUI information looks like this:
SAP PC VERSION INFORMATION: saplogon.exe
MAIN MODULE INFORMATION:
   saplogon.exe
   SAP Logon за Windows
   Final Release 710
   7100.3.13.1045
   1063164
The problem is not resolved.
This happens from different workstations with different versions and sub-versions of SAP GUI, so the problem is not caused from the GUI I think. It happens using different logon users and in all SAP system cliens.
Any other suggestions?
Best regards,
Pit

Help button not working on firefox.How to fix?

help button not working.

Hello,
Lets give Firefox some Tuneup.
The Refresh feature (called "Reset" in older Firefox versions) can fix many issues by restoring Firefox to its factory default state while saving your bookmarks, history, passwords, cookies, and other essential information.
'''''Note:''' When you use this feature, you will lose any extensions, toolbar customizations, and some preferences.'' See the [[Refresh Firefox - reset add-ons and settings]] article for more information.
To Refresh Firefox:
# Open the Troubleshooting Information page using one of these methods:
#*Click the menu button [[Image:New Fx Menu]], click help [[Image:Help-29]] and select ''Troubleshooting Information''. A new tab containing your troubleshooting information should open.
#*If you're unable to access the Help menu, type '''about:support''' in your address bar to bring up the Troubleshooting Information page.
#At the top right corner of the page, you should see a button that says "Refresh Firefox" ("Reset Firefox" in older Firefox versions). Click on it.
#Firefox will close. After the refresh process is completed, Firefox will show a window with the information that is imported.
#Click Finish and Firefox will reopen.
Did this fix the problem? Please report back to us!
Thank you.

Oracle Applications 11i Load Balancing does not work with RAC one Node

Hi all,
Could you help me to resolve this issue.
Architecture environment is :
- One APPS tier node
- Two nodes Oracle Database Appliance (Primary node 1 holds INSTANCE_1 et Secondary node is configurured to holds INSTANCE_2), i.e RAC one Node.
- The primary node have instance_name SIGM_1 and the secondary node have instance_name SIGM_2, but in RAC one node, the secondary instance is not alive.
We convert our EBS 11i environment to RAC following note ID Using Oracle 11g Release 2 Real Application Clusters with Oracle E-Business Suite Release 11i [ID 823586.1].
When testing Database failover, Oracle Applications 11i load balancing does not work anymore.
The root cause is that, when the primary node of the Rac one node is down, the INSTANCE_NAME_1 is automaically relocating to the surviving node,.
During test failover, we imagine that when the primary node goes down, the secondary node start or relocate database with instance_name SIGM_2, and in that case the Oracle Applications load balancing works.
Currently, when the primary node goes down, the instance_name SIGM_1 is relocated on the secondary node, which cause failure of Oracle Applications Load Balancing.
Thank you for your advice.
Moussa

This is something I observed a long time ago for Safari (ie: around version 1). I'm not sure this is Safari, per se, but OpenSSL that is responsible for the behavior. I'm pretty sure Chrome does this and I've seen some Linux browsers do it.
What I have done at the last two companies I've worked for is recommend that our clients do not use SSL SessionID as the way of tracking sticky sessions on web servers, but instead using IP address. This works in nearly all cases and has few downsides. The other solution is to use some sort of session sharing on your web servers to mitigate the issue (which also means that your web servers aren't a point of failure for your users' sessions). (One of the products I supported had no session information stored on the web servers, so we could safely round-robin requests, the other product could be implemented with a Session State Server... but in most cases we just used IP address to load balance with). The other solution is to configure your load balancer to terminate the SSL tunnel. You get some other benefits from this, such as allowing your load balancer to reduce the number of actual connections to the web servers. I've seen many devices setup this way.
One thing to consider through this is that - due to the way internet standards work - this really can't be termed a bug on anyone's part. There is no guarantee in the SSL/TLS standards that a client will return the same SSL Session ID for each request and there is not requirement that subsequent requests will even use the same tunnel. Remember, HTTP is a stateless protocol. Each request is considered a new request by the web server and everything else is just trickery to try and get it to work the way you want. You can be annoyed at Safari's behavior, but it's been this way for over 5 years by my count, so I don't expect it to change.

I keep trying to download Photoshop CS3 and a get a 404 error page, does Photoshop CS3 not working with a new Mac operating system?

I keep trying to download Photoshop CS3 and a get a 404 error page, does Photoshop CS3 not working with a new Mac operating system?

you must also use a browser that allows cookies. try a different browser or download from adobe.com
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 12 | 11, 10 | 9, 8, 7
Photoshop Elements: 12 | 11, 10 | 9,8,7
Lightroom: 5.5 (win), 5.5 (mac) | 5.4 (win), 5.4 (mac) | 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.

10.4.4 Mac Help does not work

I just upgraded 10.4.3 to 10.4.4. Now Tiger Mac help does not work. Other software help does work, at least those I have checked like Word, Safari, and a few others I have checked. But in the Finder going to help in the Menu bar does brings up the help window, but try to click a link like What's new in Tiger or typing a query into the search window produces nothing. All the software seems to be working fine, at least what I have checked. I have redownloaded and re-installed making sure virus software is off to no avail.
Any help would be appreciated.

I tried the steps mentioned before, and thought I would give them one more try. Initially, I had success in that the Help Viewer opened to the default Mac Help view, and when I typed in a find term, lo & behold a list of results appeared! Alas, my visions of success vanished when I clicked on one of the results, then View.....nothing happened!
I returned to the main menu, and found none of the links would work, and neither would the search function!
It appears a link may work the first time, but none after that.
I also noticed that (repeating the Cache & Preference removal steps) that they repopulated with the files when Mac Help was initiated, and, as before, would allow one link acivation to occur, but none after.
I suspect there may be a conflict with some other applications Help feature, but made sure to activate ONLY the Mac Help with no other Application having been run after restart. The only other possiblity is that some toolbar non-Mac OS X help apps like Magic Menu, Quicken, & iPod conflict, but these are all I have!
If any one having this Help Viewer problem has similar installations, or knows of any conflicts with these; or, how I can temporarily disable/remove the associated help without uninstalling them, please post a reply.
Powerbook G4 (17") Mac OS X (10.4.4)

Audition CS6 Help menu not working

I have downloaded Audition CS6. When I go to 'Help' i get error 10. Is there no help file with the trial?

Hi All,
I found this on the web and it works!
<http://forums.adobe.com/message/4417566#4417566> CS6 Help Menu Not Working
This does not apply to one application, but is a suite wide fix.
I had been running the CS6 Master Collection trial download version and the help menu, specifically the online "Help" and "Support Center" listed on the main help menu dropdowns of all applications within the suite, was not working, able to connect, or an error that the folder did not exist (apparently corrupted).
Once I just got the CS6 Master Collection (DVDs) I uninstalled the trials, then installed the hard copy version, with the normal reboot in between. The Help menus still did not work.
This is what I'm running. : Windows 7 Pro 64-bit
I called Adobe support and the following was my solution for both my desktop and netbook with this problem.
1. Close all running Adobe applications.
2. In the directory C:/Program Files (x86)/Adobe/ Delete the "Adobe Help" folder.
(C:Program Files (x86)/Adobe/Adobe Help/)
3. Reboot
4. Then go to Adobe.com/support/chc/ (this is the "community help center")
5. Click under "Step 2" the "Install Now*" button.
6. On one of the windows that open there is a Preferences drop down menu. Select the one that allows online help connection as well as local.
7. Click "download" to begin the folder download. The downloaded folders are more than 1 GB for the CS6 Master Suite help files. Watch at the bottom left of the download window to see the small progress meter.
8. Once done, reboot.
My CS6 Master Collection help menus throughout were fixed by completing the above.
Thanks Tom! ...at Adobe support for this fix procedure.
I hope this helps someone else out there.
This does not apply to one application, but is a suite wide fix.

Pages numbers and keynotes not working on handoff, but everything else is?

Pages numbers and keynotes not working on handoff, but everything else is, map, mail etc. Am I alone?

Really appreciate your help with this. I am a bit of a novice here.. but.. After some more searching on this issue I notice your comments (cut/pasted below) with respect to this router and bridging mode. You mentioned that I should update my firmware on this router and that this would (if I am interpreting your reply correctly) facilitate my LAN to LAN connection and of course using this router simply as an access point and more to the point - having the use of the guest network. So my question is even if I did update firmware, seems I would still require 3rd party software to make this work? (re your last sentence in your comments below) Just need to understand the process and determine whether or not it is worth it (or maybe I should upgrade the router) but I don't want to change the configs of the network wired router at this time... and need to use the E2500 or facsimile as simply an access point with guest network functionality, Thanks much appreciated.
"Again: some E series routers already support wired bridging in firmware, i.e. to use the router as simple access point.
This is and was always possible using a LAN-LAN setup instead.
The problem with the LAN-LAN setup is, however, that you have some limitations accessing the network storage or network printer, e.g. the router doesn't have the correct time and you cannot access the storage from remote using port forwarding through your main router.
These limitations have been overcome with the wired bridge mode (internet connection type = bridge mode).
But again: this has absolutely nothing to do with wireless bridging. That's something completely different and is not supported on Linksys routers in any firmware version so far. To do wireless bridging (i.e. the Linksys routers connects wirelessly to another main router) you need 3rd party firmware."

WBS element field in transaction CS71-F4 help is not working in ECC 6.0

Hii
In SAP, while working in SAP 4.7, tcode cs71, WBS element is coming via F4 Help. But after upgradation to ECC 6.0 EHP 5, this F4 help is not working. I can enter value manually.but F4 help is not working.
Please Help.

Hi,
You can do it manually too
1. Choose function group 'CSDI' via Transaction SE80.
2. Choose screen '0260'in the 'Screens' area and switch to change mode
3. Choose the 'Element list' tab index.
4. In this area, choose the 'Reference' tab index and enter the value
    'PRP' in the 'Search help' column in the line for field
    'RC29N-PSPNR'.
5. Save your change and regenerate the screen.
6. The correct input help for the WBS element is now available in the
    initial screen of Transaction CS71/72/73.
I hope F4 helps works for "Existing WBS BOM's" in CS71 after this
Refer to Note : 714824 as well , it has reverted back the changes done by note : 422265
Regards
Gaurav

The 'Content, index, search' section of my help is not working in Mozilla

Dear All,
The 'Content, index, search' section of my help is not working in Mozilla.
I am using robo8 and mozilla 8. Any idea? please help...
Regards,
Jobin.

Dear William,
It is a webhelp
It is working in all other browsers except Mozilla.
It is a merged help...
waiting for your reply..:)
Regards,
Jobin.

F4 help is not working in IAC Iview

Hi,
There is IAC iview for transaction PA61
F4 help is not working for the iview
it workes in backend SAP PA61
kindly give any hints what can we check
thanks in advance
b

Hi,
This might be due to the JRE version of the browser. We faced such issue and the update of JRE version in the browser helps to get the pop-up of F4 help. Check in the internet broswser Tools -> Internet Option -> Advanced. Check whether the JRE applet is checked or not. it has to be checked. if it is checked and even if you dont get the F4 help, upgrade the JRE version.
Thanks,
Mahendran B.

With input disabled field search help is not working.

Hi Web dynpro abap Gurus
Please help me on below requirement.
If i make a input field disable then the attach search help is not working. Is there is any way by which
I can make input field disabled and search help will also work for this field.
I really need help on this, Please help me.
Many thanks in advance.
Sandeep Sharma
09971995045

Hi
I dont think that a field can be disabled and allows to choose data using f4 simultaneously. you can enable the field and allow the user to select whatever he/she wants.
Then in any action like on press of save or submit button which the user will trigger after entering the values, get the value entered by the user in that perticular field and fire a query on the table/view, which you have used as selection method of your search help, it help is coming from data element then look for check table in domain. if sy-subrc comes 0 than go ahead else give error that value selected is modified.
Thanks
Vishal

In P6 EPPM Application page p6 Help is not working

Similar Messages

Maybe you are looking for