In r12 Custom Concurrent Requet taking long time
All
One of User running Custom Concurrent Request
User saying slow running process which probably is going to run for more than 6 hours.he don't want to terminate request
when user had done bulk loads in PROD on weekend the performance was much better. . Do we know what they are? Are they contributing to slow performance on the production box?
when i checked in OAM
Phase Running
Status Normal
Request ID XXXXXXX
Diagnostics This request is currently processing normally. Processing began on 02-APR-2008 13:12:03. No action required. You may examine the request log to determine its processing status.
Run times
Average 1253
Minimum 0
Maximum 14019
Estimated Completion 02-Apr-2008 13:32:56
what could be the reasons to perform slow process
So, reviewing:
1) Bulk data load took place over the weekend.
2) Custom code performs poorly after bulk load.
3) All database tables analyzed recently.
Looks like you have an adventure on your hands. :-)
No magic quick-fix here...you'll need to either review your custom code for any obvious performance bottlenecks, or trace the database session to determine where it is slowing down. Unless you're personally very familiar with the custom code, running a trace is probably a faster way to pinpoint the problem.
Good luck! In this case, at least, you're fortunate that it is custom code...if the problem is in the code itself, you have the freedom to change it, unlike the Oracle-delivered code. :-)
Regards,
John P.
Similar Messages
-
Sales order creation, standard event trigger is taking long time .
We have a requirement where we are sending data to CRM system using RFC function module. This data is sent while sales order creation or change. We have used standard event BUS2032.CREATED to trigger CRM FM in sales order creation mode. In sales order change mode, we are using custom event. In production system, our custom change event is getting triggered fine and data is sent to CRM system with small time lag of around 1 minute. But, while sales order creation, standard event trigger is taking long time ( sometimes about 20 minutes) in production system.
We tried triggering same custom event at the time of sales order creation using FM u2018SWE_EVENT_CREATE_IN_UPD_TASKu2019 as well but, still we are not able to improve performance of the event trigger at sales order creation.
Regards,
Sushee JoshiHI,
we have written SWE_EVENT_CREATE in update task
I think instead of calling in update task simply call to function module CALL FUNCTION "SWE_EVENT_CREATE" might trigger the event immediately.. Did you try to check in this way..
OR
And I also suggest you to check the entry in SWE2 txn with respect to your workflow tempalte, may be you have enable the option ENABLE EVENT QUEUE, this could be one of the reasons.. If it is enabled please disable it (uncheck)
Please check..
Regards
Pavan -
Requisition Import is taking long time to complete
Hi,
I'm working with EBS 11.5.10 CU2, I have Requisition Import program scheduled, usually it's completing normal in around 5minutes; but sometimes it's taking around 30 minutes to complete. I compared the output files of program completing normal and taking long time, latter one has processed less requisitions than former one.
Could somebody help what could be possible reasons to check for program to take long time to complete.
Please help.
Thanks945756 wrote:
Hi,
I'm working with EBS 11.5.10 CU2, I have Requisition Import program scheduled, usually it's completing normal in around 5minutes; but sometimes it's taking around 30 minutes to complete. I compared the output files of program completing normal and taking long time, latter one has processed less requisitions than former one.
Could somebody help what could be possible reasons to check for program to take long time to complete.
Please help.
ThanksDo you have the statistics collected up to date?
Please enable trace and generate the TKPROF file to find out why it takes that long -- https://forums.oracle.com/forums/search.jspa?threadID=&q=TKPROF+AND+Concurrent&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein -
Table valueset taking long time to open the LOV
Hi,
We added a table valueset to a concurrent program. The table vaueset showsTransaction number from ra_interface_lines_all table. It is having long list. So we added the partial string entering message before open a long list.But still it is taking long time.
Please any help on this highly appreciated.
Thanks,
SambaHi
Try to modify the query or creating an index will speed up the process.
Thanks & regards
Rajan -
Delete statements are taking longer time
Hi All,
I have an issue with delete statement. below are my oracle DB details.
SQL>select * from v$version;
BANNER
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - 64bit Production
PL/SQL Release 11.1.0.6.0 - Production
CORE 11.1.0.6.0 Production
TNS for Linux: Version 11.1.0.6.0 - Production
NLSRTL Version 11.1.0.6.0 - Production
I have a schema in the database which has 120 tables in it. The problem is, when the QA team is deleting the customers from customer table, it is running long time and haven't completed. this customer table have FK relation with other tables and have all the right indexes in place. then i have tried to identified the problem, why it is taking long time, and found that when they are running this delete query at the same time application is also running. the sessions created by application are locked most of the table and at the same time the delete session is also waiting for exclusive lock on those table. I given the same info to QA team and asked to stop the application when they deleting the customers. Then they said, they don't want to stop the application and the delete has to work and they asked for different solution. Here i am not sure, what solution i need to provide them.
Can you please suggest me a approach and Thanks in advance.Hari wrote:
and at the same time the delete session is also waiting for exclusive lock on those table. The only way the delete session could be waiting for an exclusive lock on the table is if the code to delete from the customer includes the command: lock table customer in exclusive mode;Unless your original description is wrong, either the deletion code has to change or the application has to stop modifying the customer table.
Regards
Jonathan Lewis
http://jonathanlewis.wordpress.com
Author: <b><em>Oracle Core</em></b> -
SSRS Reports taking long time to load
Hello,
Problem : SSRS Reports taking long time to load
My System environment : Visual Studio 2008 SP1 and SQL Server 2008 R2
Production Environment : Visual Studio 2008 SP1 and SQL Server 2008 R2
I have created a Parameterized report (6 parameters), it will fetch data from 1 table. table has 1 year and 6 months data, I am selecting parameters for only 1 month (about 2500 records). It is taking almost 2 minutes and 30 seconds
to load the report.
This report running efficiently in my system (report load takes only 5 to 6 seconds) but in
production it is taking 2 minutes 30 seconds.
I have checked the Execution log from production so I found the timing for
Data retrieval (approx~) Processing (approx~) Rendering (approx~)
10 second 15 sec
2 mins and 5 sec.
But Confusing point is that , if I run the same report at different time overall output time is same (approx) 2 min 30 sec but
Data retrieval (approx~) Processing (approx~) Rendering (approx~)
more than 1 min 15 sec
more than 1 min
so 1 question why timings are different ?
My doubts are
1) If query(procedure to retrieve the data) is the problem then it should take more time always,
2) If Report structure is problem then rendering will also take same time (long time)
for this (2nd point) I checked on blog that Rendering depends on environment structure e.g. Network bandwidth, RAM, CPU Usage , Number of users accessing same report at a time.
So I did testing of report when no other user working on any report But failed (same result output is 2 min 30 sec)
From network team I got the result is that there is no issue or overload in CPU usage or RAM also No issue in Network bandwidth.
Production Database Server and Report server are different (but in same network).
I checked that database server the SQL Server is using almost Full RAM (23 GB out of 24 GB)
I tried to allocate the memory to less amount up to 2GB (Trial solution I got from Blogs) but this on also failed.
one hint I got from colleague that , change the allocated memory setting from static memory to dynamic to SQL Server
(I guess above point is the same) I could not find that option Static and Dynamic memory setting.
I did below steps
Connected to SQL Server Instance
Right click on Instance go to properties, Go to Memory Tab
I found three options 1) Server Memory 2) Other memory 3) Section for "Configured values and Running values"
Then I tried to reduce Maximum Server memory up to 2 GB (As mentioned above)
All trials failed, this issue I could not find the roots for this issue.
Can anyone please help (it's bit urgent).Hi UdayKGR,
According to your description, your report takes too long to load on your production environment. Right?
In this scenario, since the report runs quickly in developing environment, we initially think it supposed to be the issue on data retrieval. However, based on the information in execution log, it takes longest time on rendering part. So we suggest you optimize
the report itself to reduce the time for rendering. Please refer to the link below:
My report takes too long to render
Here is another article about overall performance optimization for Reporting Services:
Reporting Services Performance and Optimization
If you have any question, please feel free to ask.
Best Regards,
Simon Hou -
Connecting to the database taking long time to connect database server
Hi
When I execute procedure i am getting the below message at bottom of the Oracle SQL Developer
"Connecting to the database"
it is taking more than 10 min plz guideHi
have you installed a normal Oracle Client also on your Host? normal Oracle Client
Did you connect with host:port:sid or with a Oracle Naming Service? through TNS Service
Can you test tnsping <alias> yes, It is working fine
Did other user have the same problem? yes
Did you connect through WAN or LAN connection? LAN (Intranet)
Can you tell more about you client/database setup?
Database setup:
OS: Window 2008 server
version: 11.1.0
Client: 11.1.0
OS: Window 2008 server
Now I am not able to execute single select query which table contains 6 records and 15 columns it is taking long time I have waited 30 min still no resutls
only one table is behaving like this remaining is working fine
Edited by: user9235224 on Oct 6, 2012 7:06 PM -
The ODS activation is taking long time
Hi,
We are on SAP NetWeaver BI 701 (Support Package 5).
We create a Z ODS, it will contain a lot of data (180.000.000 month-end) and we want to generate specific reports about it.
The activation is taking long time, I assume is because we checked the flag "SIDs Generation upon Activation". I am confused about this check. I really need it? is this check the only problem.
Thanks for you help.
VictoriaHi Victoria:
If your Z DSO is used only for staging purposes (you don't have queries based on this DSO and you send the data to another DSO or to an InfoCube) then you don't need to check the "SIDs Generation Upon Activation" box.
Even more, to achieve better performance during data loads in this scenario, you might consider using a Write Optimized DSO instead of a Standard DSO, but if you decide to take this alternative don't forget to select the "Do Not check Uniqueness of Data" box if you need to write several records with the same Semantic Key.
Regards,
Francisco Milán. -
Hi All,
We are working on BI 7.0. version
In the varaible pop-up screen we have two info objects.
1. Fiscal year Period
2. JOA(Joint operating aggriment)
If u press F4 for JOA, it is taking long time to execute and finally the application is getting closed.same situation is there in RSRT also.
If i enter with out JOA the query is giving the output. Here i have to restrict the query by JOA.
i have changed the JOA peroperties in query designer.
Query execution for filter value selection = Values in master data table.......
but still the situation is the same.......
Could you please suggest any solution for this.....
Thanks & Regards,
PKHi Kamal,
You can set that at the query level in the query designer for each query.
1. Select the corresponding characteristic in the query designer.
2. Goto to the "Extended tab" in the properties
3. Select the "Values in the Master data table" in the "Query execution in the filter value selection.
Also see some recomendations:
Note 748623 - Input help (F4) has a very long runtime - recommendations
Hope this helps.
CK -
Update ztable is taking long time
Hi All,
i have run the 5 jobs with the same program at a time but when we check the db trace
zs01 is taking long time as shown below.here zs01 is having small amount of data.
in the below dbtrace for updating zs01 is taking 2,315,485 seconds .how to reduce this?
HH:MM:SS.MS Duration Program ObjectName Op. Curs Array Rec RC Conn
2:36:15 AM 2,315,485 SAPLZS01 ZS01 FETCH 294 1 1 0 R/3
The code as shown below
you can check the code in the program SAPLZS01 include LZS01F01.
FORM UPDATE_ZS01.
IF ZS02-STATUS = '3'.
IF Z_ZS02_STATUS = '3'. "previous status is ERROR
EXIT.
ELSE.
SELECT SINGLE FOR UPDATE * FROM ZS01
WHERE PROC_NUM = ZS02-PROC_NUM.
CHECK SY-SUBRC = 0.
ADD ZS02-MF_AMT TO ZS01-ERR_AMT.
ADD 1 TO ZS01-ERR_INVOI.
UPDATE ZS01.
ENDIF.
ENDIF.
my question is when updating the ztable why it is taking such long time,
how to reduce the time or how to make faster to update the ztable .
Thanks in advance,
regards
SuniTry the code like this..
data: wa_zs01 type zs01.
FORM UPDATE_ZS01.
IF ZS02-STATUS = '3'.
IF Z_ZS02_STATUS = '3'. "previous status is ERROR
EXIT.
ELSE.
SELECT SINGLE FOR UPDATE * FROM ZS01
WHERE PROC_NUM = ZS02-PROC_NUM.
-- change
CHECK SY-SUBRC = 0.
ADD ZS02-MF_AMT TO wa_ZS01-ERR_AMT.
ADD 1 TO wa_ZS01-ERR_INVOI.
UPDATE ZS01 from wa_zs01.
ENDIF.
ENDIF.
And i think this Select query for ZS01 is inside the ZS02 SELECT statement,
This might also make slow process.
If you want to make database access always use Workarea/Internal table to fetch the data
and work with that.
Accessing database like this or with Select.... endselect is an inefficient programming. -
Simple query is taking long time
Hi Experts,
The below query is taking long time.
[code]SELECT FS.*
FROM ORL.FAX_STAGE FS
INNER JOIN
ORL.FAX_SOURCE FSRC
INNER JOIN
GLOBAL_BU_MAPPING GBM
ON GBM.BU_ID = FSRC.BUID
ON UPPER (FSRC.FAX_NUMBER) = UPPER (FS.DESTINATION)
WHERE FSRC.IS_DELETED = 'N'
AND GBM.BU_ID IS NOT NULL
AND UPPER (FS.FAX_STATUS) ='COMPLETED';[/code]
this query is returning 1645457 records.
[code]PLAN_TABLE_OUTPUT
| Id | Operation | Name | Rows | Bytes | Cost (%CPU)|
| 0 | SELECT STATEMENT | | 625K| 341M| 45113 (1)|
| 1 | HASH JOIN | | 625K| 341M| 45113 (1)|
| 2 | NESTED LOOPS | | 611 | 14664 | 22 (0)|
| 3 | TABLE ACCESS FULL| FAX_SOURCE | 2290 | 48090 | 22 (0)|
| 4 | INDEX RANGE SCAN | GLOBAL_BU_MAPPING_BUID | 1 | 3 | 0 (0)|
| 5 | TABLE ACCESS FULL | FAX_STAGE | 2324K| 1214M| 45076 (1)|
PLAN_TABLE_OUTPUT
Note
- 'PLAN_TABLE' is old version
15 rows selected.[/code]
The distinct number of records in each table.
[code]SELECT FAX_STATUS,count(*)
FROM fax_STAGE
GROUP BY FAX_STATUS;
FAX_STATUS COUNT(*)
BROKEN 10
Broken - New 9
Completed 2324493
New 20
SELECT is_deleted,COUNT(*)
FROM FAX_SOURCE
GROUP BY IS_DELETED;
IS_DELETED COUNT(*)
N 2290
Y 78[/code]
Total number of records in each table.
[code]SELECT COUNT(*) FROM ORL.FAX_SOURCE FSRC-- 2368
SELECT COUNT(*) FROM ORL.FAX_STAGE--2324532
SELECT COUNT(*) FROM APPS_GLOBAL.GLOBAL_BU_MAPPING--9
[/code]
To improve the performance of this query I have created the following indexes.
[code]Functional based index on UPPER (FSRC.FAX_NUMBER) ,UPPER (FS.DESTINATION) and UPPER (FS.FAX_STATUS).
Bitmap index on FSRC.IS_DELETED.
Normal Index on GBM.BU_ID and FSRC.BUID.
[/code]
But still the performance is bad for this query.
What can I do apart from this to improve the performance of this query.
Please help me .
Thanks in advance.<I have created the following indexes.
CREATE INDEX ORL.IDX_DESTINATION_RAM ON ORL.FAX_STAGE(UPPER("DESTINATION"))
CREATE INDEX ORL.IDX_FAX_STATUS_RAM ON ORL.FAX_STAGE(LOWER("FAX_STATUS"))
CREATE INDEX ORL.IDX_UPPER_FAX_STATUS_RAM ON ORL.FAX_STAGE(UPPER("FAX_STATUS"))
CREATE INDEX ORL.IDX_BUID_RAM ON ORL.FAX_SOURCE(BUID)
CREATE INDEX ORL.IDX_FAX_NUMBER_RAM ON ORL.FAX_SOURCE(UPPER("FAX_NUMBER"))
CREATE BITMAP INDEX ORL.IDX_IS_DELETED_RAM ON ORL.FAX_SOURCE(IS_DELETED)
After creating the following indexes performance got improved.
But our DBA said that new BITMAP index at FAX_SOURCE table (ORL.IDX_IS_DELETED_RAM) can cause locks
on multiple rows if IS_DELETED column is in use. Please proceed with detailed tests.
I am sending the explain plan before creating indexes and after indexes has been created.
SELECT FS.*
FROM ORL.FAX_STAGE FS
INNER JOIN
ORL.FAX_SOURCE FSRC
INNER JOIN
GLOBAL_BU_MAPPING GBM
ON GBM.BU_ID = FSRC.BUID
ON UPPER (FSRC.FAX_NUMBER) = UPPER (FS.DESTINATION)
WHERE FSRC.IS_DELETED = 'N'
AND GBM.BU_ID IS NOT NULL
AND UPPER (FS.FAX_STATUS) =:B1;
--OLD without indexes
PLAN_TABLE_OUTPUT
Plan hash value: 3076973749
| Id | Operation | Name | Rows | Bytes | Cost (%CPU)| Time |
| 0 | SELECT STATEMENT | | 141K| 85M| 45130 (1)| 00:09:02 |
|* 1 | HASH JOIN | | 141K| 85M| 45130 (1)| 00:09:02 |
| 2 | NESTED LOOPS | | 611 | 18330 | 22 (0)| 00:00:01 |
|* 3 | TABLE ACCESS FULL| FAX_SOURCE | 2290 | 59540 | 22 (0)| 00:00:01 |
|* 4 | INDEX RANGE SCAN | GLOBAL_BU_MAPPING_BUID | 1 | 4 | 0 (0)| 00:00:01 |
|* 5 | TABLE ACCESS FULL | FAX_STAGE | 23245 | 13M| 45106 (1)| 00:09:02 |
PLAN_TABLE_OUTPUT
Predicate Information (identified by operation id):
1 - access(UPPER("FSRC"."FAX_NUMBER")=UPPER("FS"."DESTINATION"))
3 - filter("FSRC"."IS_DELETED"='N')
4 - access("GBM"."BU_ID"="FSRC"."BUID")
filter("GBM"."BU_ID" IS NOT NULL)
5 - filter(UPPER("FS"."FAX_STATUS")=SYS_OP_C2C(:B1))
21 rows selected.
--NEW with indexes.
PLAN_TABLE_OUTPUT
Plan hash value: 665032407
| Id | Operation | Name | Rows | Bytes | Cost (%CPU)| Time |
| 0 | SELECT STATEMENT | | 5995 | 3986K| 3117 (1)| 00:00:38 |
|* 1 | HASH JOIN | | 5995 | 3986K| 3117 (1)| 00:00:38 |
| 2 | NESTED LOOPS | | 611 | 47658 | 20 (5)| 00:00:01 |
|* 3 | VIEW | index$_join$_002 | 2290 | 165K| 20 (5)| 00:00:01 |
|* 4 | HASH JOIN | | | | | |
|* 5 | HASH JOIN | | | | | |
PLAN_TABLE_OUTPUT
| 6 | BITMAP CONVERSION TO ROWIDS| | 2290 | 165K| 1 (0)| 00:00:01 |
|* 7 | BITMAP INDEX SINGLE VALUE | IDX_IS_DELETED_RAM | | | | |
| 8 | INDEX FAST FULL SCAN | IDX_BUID_RAM | 2290 | 165K| 8 (0)| 00:00:01 |
| 9 | INDEX FAST FULL SCAN | IDX_FAX_NUMBER_RAM | 2290 | 165K| 14 (0)| 00:00:01 |
|* 10 | INDEX RANGE SCAN | GLOBAL_BU_MAPPING_BUID | 1 | 4 | 0 (0)| 00:00:01 |
| 11 | TABLE ACCESS BY INDEX ROWID | FAX_STAGE | 23245 | 13M| 3096 (1)| 00:00:38 |
|* 12 | INDEX RANGE SCAN | IDX_UPPER_FAX_STATUS_RAM | 9298 | | 2434 (1)| 00:00:30 |
Predicate Information (identified by operation id):
PLAN_TABLE_OUTPUT
1 - access(UPPER("DESTINATION")="FSRC"."SYS_NC00035$")
3 - filter("FSRC"."IS_DELETED"='N')
4 - access(ROWID=ROWID)
5 - access(ROWID=ROWID)
7 - access("FSRC"."IS_DELETED"='N')
10 - access("GBM"."BU_ID"="FSRC"."BUID")
filter("GBM"."BU_ID" IS NOT NULL)
12 - access(UPPER("FAX_STATUS")=SYS_OP_C2C(:B1))
31 rows selected
Please confirm on the DBA comment.Is this bitmap index locks rows in my case.
Thanks.> -
Hi
Is there any provision or api in MAC to open a file in shared mode same as windows
hUSBdrive = CreateFile(pDriveName, GENERIC_READ | GENERIC_WRITE, FILE_SHARE_READ | FILE_SHARE_WRITE, NULL, OPEN_EXISTING, FILE_FLAG_NO_BUFFERING, NULL);
we have the follwing scenario where a file is shared among two processes for read/write.one is running on Linux and the other one is running on MAC.where both the processses are reading/writing into the same memory location in the file say "X"
FAT 32 formatted raw data file which is located on the device, is shared among two processes.
One process is running on Linux device which is connected to MAC book through usb.In this linux process, the file is opened using fopen() and we have used fcntl() with O_DIRECT flag.This process continuously reads/writes data on memory location "X" in the shared file .
The other process is running on Mac which has simple c program that opens the file on the connected device i.e from usb drive and reads/writes data using fread()/fwrite().fopen() is used to open the file and FILE_NOCACHE flag is used to avoid caching.
The value at memory location "X" is updated by mac by using fwrite() and the linux process reads the memory location "X" by using fread(). Linux process is taking around 30 sec to get the updated value.
If the value is updated by Linux process at memory location "X" by using fwrite() the MAC process is also taking long time more than a minute to read the updated value by usng fread().
fwrite()/fread() on mac is taking long time where as the windows application which uses the same apis is taking msec time.
Do we need to use other api s or flags to open file?
thanks in advance.......does any one face this kind of problem?
fwrite() and fread() takes long time?
Is there any problem in read/write to a fat32 file on MAC? -
Hi,
RSPCM is taking long time to open at the same time RSPC is working fine
when I try to change the process chain status through RSPC_PROCESS_FINISH . it is executing for long time no response. I tried executing it backgrond also from past 2 days it is running, no progress.
Our basis team created index to all backend table of RSPCM, still issue persist. Please suggest me some to get rid of this.
Br,
Harishhi,
Please check the below thread
RSPCM T-Code was executing very slow
Please check note 1372931
hope it helps!
Edited by: Lavanya J on Nov 4, 2011 1:32 PM -
VB Macro in Bex Analyser is taking long time to complete execution
Hi Experts,
In a FI query , we have a VB macro which update the excel sheets by taking values from the previous excel sheets .
The issue is its taking long time for query execution and if we are keep on pressing 'ENTER' button . The query is running very fastly and is giving the results ,but its not a correct way to do.
Its a critical issue in Production and can anyone help me to resolve the issue.
Regards,
AnjuHi Anju,
I need to create a VB macro in one of my query but i not familiar how i can plug the VB code into the query.
Please can you give me some basic procedure on how to do that?
What i need to do exactly is to bring a KF from a query into another query. Not sure if this is possible using VB.
Let me know.
Thanks.
Cesar -
Retry recovery action is taking long time to complete
Hi,
I am in the process of testing error handling for my BPEL process.
As part of it, I have given the default recover action in the fault policy of the process as retry with a retry count of 3 times with retry interval as 2.
To test this, i have changed the target end point uri of the target service to some invalid url and ran the process.
First I was not able to find the BPEL process instance at all in the console.
Later I was able to find the instance after half an hour. When I saw the instance, if retry had happened or not.
I found that the retry happened for 3 times, but it took 30 mins for the first retry to complete and start the second retry.
Can anyone please let me know why the retry is taking long time although the retry interval I gave is only 2 seconds.
THanks in advance!!!!Hi,
Please find below the fault policy file:
<?xml version="1.0" encoding="UTF-8"?>
<faultPolicy version="2.0.1" id="TestFaultPolicy" xmlns:env="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xs="http://www.w3.org/2001/XMLSchema" xmlns="http://schemas.oracle.com/bpel/faultpolicy" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<Conditions>
<faultName>
<condition>
<action ref="aia-ora-retry"/>
</condition>
</faultName>
</Conditions>
<Actions>
<Action id="aia-ora-retry">
<retry>
<retryCount>3</retryCount>
<retryInterval>2</retryInterval>
<exponentialBackoff/>
<retryFailureAction ref="aia-ora-java"/>
<retrySuccessAction ref="aia-ora-java"/>
</retry>
</Action>
<!-- This is an action will cause a replay scope fault-->
<Action id="ora-replay-scope">
<replayScope/>
</Action>
<!-- This is an action will bubble up the fault-->
<Action id="ora-rethrow-fault">
<rethrowFault/>
</Action>
<!-- This is an action will mark the work item to be "pending recovery from console"-->
<Action id="ora-human-intervention">
<humanIntervention/>
</Action>
<!-- This action will cause the instance to terminate-->
<Action id="ora-terminate">
<abort/>
</Action>
<Action id="aia-ora-java">
<javaAction className="oracle.apps.aia.core.eh.BPELJavaAction" defaultAction="ora-rethrow-fault">
<returnValue value="REPLAY" ref="ora-terminate"/>
<returnValue value="RETRHOW" ref="ora-rethrow-fault"/>
<returnValue value="ABORT" ref="ora-terminate"/>
<returnValue value="RETRY" ref="aia-ora-retry"/>
<returnValue value="MANUAL" ref="ora-human-intervention"/>
</javaAction>
</Action>
</Actions>
</faultPolicy>
Maybe you are looking for
-
I have photos from several cameras of the same event, how do I combine them?
I have photos from several cameras of the same events. How can I sort them together, three pics of the same horse from three cameras side by side; I can't move pics from one camera source to another in a folder.
-
Is it possible to change the "From Email Address in workflow"
I have a created a task list and set a workflow for the list. Workflow Actions: 1. Send a Email to the "Assigned To" user whenever a task is created. 2. If the Task is due, send an reminder Email and even if its not completed, send a Email to the hig
-
MacBook Air won't recognize iOmega External Hard Drive
I just bought my macbook air and I wanted to transfer my data over from my old MacBook. The MacBook died so I was using my backup. The problem is that the Air won't recognize the ext hard drive. I connected the ext hard drive to my AirPort Extreme fo
-
Builder.parse return null under jdk 1.5.0
I would like to understand why the following code return a correct Document instance if it running under jdk 1.4.2 and instead return null if it running under jdk 1.5.0. Thanks! F. String test = "<root>" + "" + "</root>"; StringReader sreader = new S
-
Can I use Audacity to create Cuepoints?
If you can't, is there another open source alternative to Adobe for creating markers? Thanks.