Inappropriate Temperatures with P45 Platinum

Greetings to Everyone.
Ok, i bought MSI P45 Platinum recently. and i must say, i am quite impressed with whats it delivering at the moment. I tried setting FSB to 380 with multiplier:9 and left all the rest settings on auto. Machine performed POST without any issues. However, idle temps were around 66 degrees, as processor has stock HSF! So, shifted back to 3.04Ghz (380x8) with 1:1 divider and with memory timings: 4-4-4-12.
Everything went fine. System passed IntelBurn Test, Prime95 and 3DMark06 stability and benchmark tests with flying colors. Super-Pi 1M was calculated at 15 secs. I say not bad for Q6600 @3.04Ghz!
However, during all these tests i constantly faced errorenous temperature display with utilities. I consistently monitored everything on CoreTemp, RealTemp, Intel TAT, HWMonitor, SpeedFan and as well as MSI Dual Core Centre! (lol had to be sure which one gave accurate, so tried everyone of em! :D) Now, here is the thing:
Except Dual Core Centre, everyone else showed temps @ idle around 60 degrees and @ load around 75 degrees! While dual Core showed idle @ 48 degrees and @ load around 56 degrees! Another thing, both CoreTemp and MSI utlity showed same readings with Core percentage usage.
See, everything seems so normal. I am using CoolerMaster Elite 333 cabinet with two 120mm fans at front and back. My GPU idles around 55 degrees and hard disk temperature never crosses 40 degrees! So, what is wrong with CPU temperature??
Please, i desperately need your advice on this.
Another thing, my friend is using P35 Platinum and everything same as mine. However, his machine never crosses 47 degrees at idle @ 3.0Ghz! Then why mine?
Thanks...

awesome!! Three senior members helping me. Plus, thanks for such a fast response.
Thank you henry, Jack and Frank..!
I followed your advice and reseated heat sink assembly after cleaning the CPU heat spreader and applying AS5.
In the beginning, something went wrong and realtemp showed all cores above 95 degrees!! For some time i took that as a joke. But, later i reseated HSF assembly again and this time everything went fine. I am right now @2.4Ghz and processor idles around 46 degrees. Pretty pleased with the results. Ran Intel Burn test for an hour and temps rarely crossed 75 degrees!! (And ohh btw, that Intel Lin Pack really shoot temps like anything! What a thing!) Ok, everything went fine.
However, there are few things i would like to clear..
1. That EVGA card blows too much of heat within the cabinet! Only raising the fan speed to 60% helps bringing down the overall system temps by 4-5 degrees!! I mean, i dont want to sound naive...but is it supposed to happen this much? And somehow if it does then what can i do? Comments please...
2. I think, Q6600 can be o/c'd pretty easily on this board. However, i have few doubts..
(a) Do i always have to stick with 9 multiplier?? I mean, i tried with 8, and everything went fine. But, if everything is good to go with 9 multiplier then there is options for lower figures? I mean are there any benefits with different figures?
(b)Spread spectrum should be left enabled while overclocking?
(c)And what about Green Power and EIST? EIST should be disabled while overclocking. But can we leave Greenpower on?
(d)I may have options to go for CoolerMaster CPU cooling setups. Why coolermaster only? Ok, thats because, in here, we dont have brands like Arctic, Thermaltake or Zalman in markets! :( I mean, they can be ordered through net, but i think its better to purchase from a retailer with all bills and stuff. Anyways, suggestions required for a descent CoolerMaster CPU cooler. That'd be good right?
(e)How much difference does third party cooler can make in comparison to a stock one?
Thank you again for ur replies.

Similar Messages

Problem with P45 Platinum during POST

Good day!
I have MSI P45 Platinum mainboard and from to time to time it freezes during POST with AMI bios POST code - 423C. This happens right after the message that "4096MB OK" and before the detection of SATA/IDE drives. When this happens, the only way to make the system run is to turn off the power (pressing Ctrl-Alt-Del of Reset would result in the same error) - after that the POST procedure finishes correctly and I don't experience any problems afterwards (system is rock-solid after POST completion).
So my question is - can anyone explain me what does this post code mean (D-Leds are not much of a help)? Is this a mobo problem or may be there is some kind of incompatibility with my hardware. I should mention also that I've tried all versions of Bios both official and beta without any success.
This problem does not trouble me that much (doesn't happen often), but still I would like to understand what may cause it.
P.S. My system config - iC2D E8300/MSI P45 Platinum/4x1Gb DDR2-800 Geil Black Dragon (5-5-5-15)/MSI Radeon 4870 1Gb OC edition/HDD 250 Gb WD + 120Gb Seagate/SB Audigy 4/DVD-RW Asus 1814/PSU TT Toughpower 700w (w0105)
Thanx in advance and please excuse my poor English

Thank you for the reply!
Quote from: Jack the Newbie on 16-December-08, 06:39:42
What is your current BIOS Version?
I've recently flashed the latest beta bios version - 1,5 beta 6... but it produces the same error as did the latest official bios v1.4
Quote from: Jack the Newbie
Does the same problem occur with only one memory module installed?
I don't know actually. But thanks for pointing this out - I will test the system with one (and then with two) module(s). I've tested the modules with the memtest86+ software (the latest version, which supports P45 chipset) several times and it showed no errors. So the modules are OK and they worked without any problems with my previous mb (Gigabyte P35-DS3).
Quote from: Jack the Newbie
What do the POST-Status LEDs of the board tell you, when the system freezes at the described stage?
Well, I guess I don't fully understand what does the combination of LEDs tell during the freeze. I'll try to describe the combination -
LED12 - OFF LED13 - GREEN
LED8 - RED LED7 - OFF
LED14 - OFF LED10 - GREEN
LED15 - RED LED11 - OFF
In mobo's manual this diagnostic LEDs are grouped in 4 groups and the description of the group that most closely resembles my case is - "Testing base and Extended memory etc." But I'm not sure that I'm identifying the problem correctly, because of the LEDs that are OFF.
Quote from: Jack the Newbie
Are you experiencing any freeze and/or stability problems appart from the described problem?
No, as I said in my initial post, once it get past this stage everything is running smoothly - OS boots and all software, including the most demanding games or tests, are running OK.

Doubt about overclocking with p45 platinum

hi guys
i have a Q8200 processor and an MSI p45 platinum motherboard.
now the multiplier on the processor is 7
now using a a bus speed of 400mhz i was able to achieve a 400 * 7 = 2.8Ghz on my processor from 2.33
now when i use cpuZ it shows that im currently running at 1600fsb
now as per the board specs 1600 fsb is the maximum.
now does this mean that i wont be able to overclock further ?
i am currently using transcend 800 mhz DDR2 ram
i have the memory divider set at 1:1
so the rams are running at 800mhz
now if i try to further overclock the board, it results in a no boot. i get a single green light and rest 3 are red and the mother board restarts 3 times and then i get the overclock failed message could some 1 advise me on how to go further increase my overclock ?
i have tried to increase my processor voltage and my ram voltage by quite a bit (not over the safe limit though) but still not able to boot :(

Quote
now as per the board specs 1600 fsb is the maximum.
This just states that Processors that natively run @400 MHz FSB Clock Speed are supported. It has nothing to do with overclocking margins.
Try this for a quick test:
- turn off the system
- remove both OC Jumpers to force the FSB Clock Speed to 400 MHz
- Clear CMOS with main A/C power cable removed from PSU
See if the system boots and runs stable. If it does, use the BIOS for further overclocking from the 400 MHz Strap. As you are forced to overclock your memory modules as well when you raise the FSB Clock Speed beyond 400 MHz try raising the memory voltage to 1.9-2V to see if that helps.
Spread Spectrum should be enabled at all times in the Cell Menu.

Issues with P45 Platinum in Antec 900

Just got my Antec 900 today and put my motherboard inside. Everything was connected a-okay. I booted it up and immediately saw somethig smoking towards the bottom of the motherboard where the Reset and Power switch are. So I shut it down and tripple checked the wiring. Everything was still a-okay. Now when I try to boot it up, my motherboard won't post! I look at the LED lights and only group 2 shows up green, groups 1, 3 and 4 are all red.
"Memory Detection Test
Testing onboard emory size. The D-LE will hang if the memory module is damaged or not installed properly."
Did I just fry my motherboard? The ony differences in wiring was the USB and all that stuff on the bottom of the board. And it's not like it didn't work, because I used that to boot up the computer the first time.
Anyone have any ideas?

Remove MB from case and ensure no MB mounting standoffs are in the wrong place (not aligned with MB mounting screw holes) or a stray screw in there causing a short. Also check for pinched wires and other such things. Any chance you can take any good close-up high rez photos of the area in question also before you take it apart?
Usually if you let the sealed in smoke out of any electronics you can expect to pay more money to get things right again.
At any rate you will need to take it apart and make a good visual examination to see exactly what may have fried.

P45 Platinum IEEE1394 drivers for Win7 x64

I just reinstalled my PC with P45 Platinum mainboard and everything installs fine with the drivers from the MSI website, however there is no driver for IEEE1394 controller there.
I installed Win7 x64 now, before I installed WinXP and at the time of that installation it installed fine.
I am not using the IEEE1394 controller at the moment but there is a exclamation point in the device manager I want to get rid of.
Can anyone point me to the driver, thnx.

In windows 7 there's no Firewire driver needed it should automatically install it as already integrated. Is it already installed and exclamation mark on it like it isn't working correctly or unknown device?

P45 Platinum with Q9550 problem

Hi there,
here's my spec :
P45 platinum board (bios 1.51)
Q9550 (E0)
Gskill PC8800 pi 2x2Gb DDR2
2x Gecube 3870 turbo
Cooler Master M700 real power
Zalman CNPS 9700
and then my problem is i cant go stable over 412 fsb. Im trying hard to setup in cell menu bios and never luck. No matter how many u rise voltage at vcore,vtt,vmch,etc. and lower multiplier (also ratio 1:1) its always unstable. If i could not wrong, i heard many guys out there seems problem too, and that because the bios boards issue? I find something wrong with bios 1.51, my quads its too high temp than real and i cant set vcore over 1.19 and vmch over 1.35
Please help me, i need advice & suggestion. thanx be4

Quote from: AaronYuri on 25-July-09, 14:33:54
Check the temperatures with CoreTemp.
ahaa.. u got right intuition Aaron. Well, i check up temp with 2 model. First, as ur suggest using with Core Temp 0.99.4, and the second with HWmonitor Ver. 1.08. But too bad i cant post the pic in here because my internet connection bandwitch is very, very slow.... (oh god, i waste the time for upload it) :-(
I strap fsb to 400 (3.4Ghz) and averything i set it auto (nothing more OC, just only strap fsb)
On the Core Temp shows 42C at idle (1.1 Vcore), and various temp core1-4 between 41-44C. and with HWmonitor its shows 48C (1.09 Vcore) at idle and various temp core1-4 between 46-49C. And last in bios, vcore always show between 50-52C
Ok, now which better i trust? .. lol
and.. oh ya aaron, if u dont mine can u tell me ur setup in cell menu to OC ur quad 9450 at x48 boards? I know its different chipset but just for compare.
Thx for ur help again.

Problem with MSI P45 Platinum DDR2 mainboard and Corsair Dominator PC8500C5D Ram

Hi, I have encountered with a problem.
First I had
MSI p45 platinum ddr2 bios ver. 1,4
Intel E8400
Corsair Dominator PC8500C5D 2x1Gb
2 Asus ATI EAH 3870 Crossfire
and it was running with windows XP without any problems.
Problems began when I decided to upgrade to 6Gb of ram and to install Vista 64. Ram modules witch I bought are the same Corsair Dominator PC8500C5D, but 2x2GB.
When i put them together adjust voltage 2.1v and timing 5-5-5-15 they fail mem test with huge amount of errors.
when I test only 2x2gb modules memtest sometimes doesn't open at all, sometimes just stops working on 8 minutes of test. couple of times they completed memtest without any errors.
Can someone advice what should I do and what could the problem?
Thank you for your answers.

Quote from: obsessed on 15-October-08, 18:20:44
Corsair Dominator PC8500C5D 2x1Gb
Problems began when I decided to upgrade to 6Gb of ram and to install Vista 64. Ram modules witch I bought are the same Corsair Dominator PC8500C5D, but 2x2GB.
1) the modules are not the same (the DDR2 chips are different)
2) as general rule, mixing 2x1GB with 2x2GB is a bad idea.
cheers

Overclocking Q6600 with MSI P45 Platinum

Hi again!
I need some advice regarding my OC settings.
Unfortunately, im an unlucky owner of the infamous Q6600 L8XX batch which has a high VID (1.3250v)
Anyway, I was able to reach 3GHz stable with these settings:
MSI P45 Platinum official v1.5 bios
Motherboard OC Jumper set to: default
================================
C1E: Disabled
Green Power: All Disabled
================================
Multi-Step OC Booster: Mode 1
DOT Control: Disabled
Intel Eist: Disabled
Adjust CPU FSB Frequenxy (MHz): 333
Adjust CPU Frequency: 3000
CPU Multiplier: 9
================================
Advance DRAM Configuration: Manual
Enhanced Settings: Enabled
NB Drive Config: auto
CAS Latency (CL): 5
tRCD: 5
tRP: 5
tRAS: 15
Advanced memory Setting: Disabled
FSB/DRAM ratio: 1:1.2
Adjusted Dram Frequency: 800
================================
ClockGenTuner: No Changes Done
Adjusted PCI Frequency: 37.5
Auto disable DRAM/PCI Frequency: Disabled
================================
CPU Voltage: 1.3175v
CPU GTL REF0: auto
CPU GTL REF1: auto
Dram voltage: 2.100v
DDR_VREF_A: auto
DDR_VREF_B: auto
MCH Voltage: 1.4v
MCH GTL REF: auto
VTT FSB Voltage: 1.35v
ICH Voltage: 1.52v
================================
Spread Spectrum: Disabled
My goal is set at 3GHz and to get a lower cpu voltage (lower than my current 1.3175v), but anything below 1.3175v restarts when i stress test using OCCT. I've run memtest and it's ok. Can anybody advise which voltage I can configure to lower my cpu voltage? Also, is 333 x 9 to achieve 3GHz better? Or should I go with 375 x 8? Thanks! Btw, I plan to maintain these settings for the remainder of my CPU's life.. :D

thanks for the tip. i'm currently logging all my OC settings in an excel file. i just finished played an hour of COD4 without any restarts or instability. currently my settings are just the same except CPU voltage is at 1.344v and i reduced my Dram voltage to 2.0v. running memtest for over an hour, 2 passes already with no errors. i'll stress test it over the weekend.
i have a question though. a lot of people are suggesting a 1:1 FSB/DRAM ratio. but using 333x9 settings @ 1:1, you get 667.. i'm using 2x 2GB GeiL PC6400 800, that's why i used the 1:1.2 FSB/DRAM ratio to get 800. is it ok to keep using the 1:1.2 FSB/DRAM ratio even though people say 1:1 is the ideal ratio? many thanks for the reply

MSI P45 PLATINUM with Cooler Master V8

Hi i was wondering if the Cooler Master V8 would fit well with an msi p45 platinum board (mid size tower with q9550 cpu) without hitting the pipes. cus i havt been able to google any images with these two together
any suggestions?!
cheers!

The Zalman 9900 would be another good choice to consider. http://s326.photobucket.com/albums/k432/HU16E/P45/

P45 Platinum Optimum memory settings with 2GB Corsair 1066 memory

Hi all,
Looking for some advice on optimum memory settings as I seem to have been getting unstable results from experimenting with settings and the optimum defaults.
My configuration is as follows:
MSI P45 Platinum (V1.0 PCB) (V1.4 Bios)
Intel Dual Core Duo E8500
Corsair TWIN2X2048-8500C5D DDR2-1066 5-5-5-15-2T configured for 2.2v in Bios
Palit 9800GT
2 x Maxtor 1TB HD's
1 x Floppy + Memory card readers
2 x Samsung DL-DVD-DW's
Silverpower SP-400P2C 400W PSU
With the default optimised settings loaded, the system does not book reliably or pass the memory test, in fact memtest86 just hangs when booted
With the Memory configuration set to 1:1.33 (1600:1066) the systems appears to pass the memory tests and windows is relatively stable. Voltage set to 2.2volt with Spead Spectrum disabled.
Is this really the optimum configuration ? as the Adjusted DRAM Frequency reported by the bios is 887 and I was expecting to see 1066.
Any suggestions as how to optimise reliably would be appreciated.
Although I suspect I may have a PSU issue as once booted the system locks when running any 3D games/demo's and it looks liek the 9800GT's need a lot more amps that I thought when putting the system together.
Rgds

Quote from: sylvester on 11-October-08, 20:43:36
Intel Dual Core Duo E8500
Corsair TWIN2X2048-8500C5D DDR2-1066 5-5-5-15-2T configured for 2.2v in Bios
With the Memory configuration set to 1:1.33 (1600:1066) the systems appears to pass the memory tests and windows is relatively stable. Voltage set to 2.2volt with Spead Spectrum disabled.
Is this really the optimum configuration ? as the Adjusted DRAM Frequency reported by the bios is 887 and I was expecting to see 1066.
First of all, your DDR2 modules are in fact DDR2-800 (they're using overclocked-overvolted DDR2-800 chips).
Sencondly you need to understand how a FSB/DRAM divider works.
Your processor is Intel E8500 and that means a bus frequency of 1333MHz (333MHz quad-pumped).
In your case 1:1.33 means 1.33 x 333 x 2 = 887 MHz for the DDR2 modules.
Set the divider to 1:1.6 if you want the DDR2 modules to run at 1066MHz.
And finally, the "optimum configuration" for max system stability means real DDR2-1066 (7-7-7-20 at 1.8V) or
DDR2-800 (5-5-5-15 at 1.8V).
cheers

P45 platinum having issues with 8 gigs of Ram

I just put together a new system. When I tried to install windows it kept giving me an error couldn't load winload.exe. I immediately thought I had a bad stick of ram. I ran Memtest with no errors reported. I tried taking 3 of the 4 sticks of ram out and then windowds would start to install fine. I tried every stick of ram this way and it all worked. Putting 2 sticks in is fine also (4 gigs total). Whenever I add 2 more sticks the board goes into an infinite reboot cycle. Having tested the different possible combinations of the sticks and the slots on the motherboard I am at a loss. Also this is OZC memory that is on the motherboards approved list and has been tested with it by MSI. Anyone know of others who have had issues with 8 gigs. Is there a bios setting I should try and change? Thank You!
Bios version 1.3
Bios settings are all default (auto)
cpu q9550
ram 2 of these for a total of 8 gigs. OCZ 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model OCZ2P8004GK
MSI P45 Platinum LGA 775 Intel P45 ATX
PC Power & Cooling S75QB 750W ATX12V / EPS12V SLI NVIDIA SLI Certified (Dual 8800 GTX and below) CrossFire Ready 80 PLUS Certified Active PFC Power Supply

Quote
Cant figure out how to upload the screen shot dont have a place to post it and link it.
This is a good side to host pictures:
http://photobucket.com/
Here is the info from cpu-z
slot 1 DDR2
Quote
Size 2048Mb Correction None
Max Bandwidth PC2-6400 (400mhz)
Manufacture OCZ
Part OCZ2p8002G
Freq 333mhz 400 mhz
CAS# 4.0 5.0
RAS-CAS 5 6
RAS prechar 5 6
tras 15 18
trc 20 24
Voltage 1.8v 1.8v
Okay, typical idiosyncratic OCZ SPD Profiles.
In Cell Menu, try these settings:
DRAM Voltage = 2.0V
MCH Voltage = 1.3V
Spread Spectrum = Disabled
Auto Disable DIMM/PCI Frequency = Disabled
Save & Exit, shutdown your system, add the other memory modules and see what happens when you start your system.
If that does not work, start again with only two modules, reduce memory clock speed to 667 MHz (FSB/DRAM Ratio = 1:1) and retry with four modules.

P45 Platinum - OCing with FSB jumpers

Hi,
I have already had problems with my memory and you guys helped me alot so i suggested to post my new problem here,,, maybe you guys know what to do.
I have a MSI P45 platinum with Intel Q9550 but when i check the ratings with CPU-Z it says my CPU is running at 2 GHZ and only using 6.0 x multiplier... were it should be 2.83 GHZ and 8.5 x multipliere ( Stock settings ).. how is this possible and how to fix this ? also in the BIOS it says its just running normal ( 2.83 GHZ at 8.5 x ) and so thoes windows XP and vista do ( they show 2.83 GHZ. ) but i think that is normal since vista and XP see a Q9550 and tell me it runs on 2.83 GHZ when its working properly.
it is running on 1333 MHZ ( well its 1336.4 to be exact) but i think it won't hurt if its running on it right ?
what settings should i change to let it run normal ? maybe the voltage for the CPU ?
Also i was checking my BIOS for this problem but i couldn't find he multiplier option where you can OC it... or do i need to enable something for it ?
Thanks for everyone's time and wisdom

Quote
so i guess its ok...
Definately!
Quote
Also where can i change the multiplier in BIOS for overclock ?
You need an Intel Extreme Edition Processor to be able to overclock the CPU by rasing the multiplier beyond standard. On all other model, all ratio higher than default are locked by Intel.
Quote
or should I raise the FSB bus speed a little higher.. what do you suggest ?
Raising the FSB Clock Speed is the only way to overclock the processor. You can try to remove the OC Jumpers of the board completely, which will force the FSB Frequency to 400 MHz via hardware. Do a CMOS Clear (with main A/C power cable removed from PSU) after removing the jumpers and see if the system will start up okay. Alternatively, you can simply raise the FSB Clock Speed in BIOS (but keep the FSB/DRAM Ratio in mind, when you do that, as the memory clock is tied to the FSB Clock via set ratios.)

Issue with the line of 12+ on my p45 platinum

Hi guys, i'm watching long days ago, my line of 12+ go to 1.76 idle, and 4.80 load, why is the issue, i have at Antec Earthwatt 500w
this my full ring
MSI p45 platinum (bios 1.6)
Intel Core 2 duo E8400 3.0 mhz (E0)
2gb corsair ddr2 800mhz
HD4890 Vapor-x 1gb ddr5
Maxtor 500gb
Please can u tell me if this is normal or i'm can have serious problem with it

ok thanks so much

P45 Platinum/Zilent with 8800GT problem

Specs:
Core 2 Duo E6300 1.86Ghz (next item to be upgraded)
P45 Zilent (aka Platinum) V1.1
1xKingston 2GB DDR2 800
PCI-E 2.0 Inno3D 8800GT OC 512MB
Seagate 1x250GB 7200rpm SATA
External Western digital 500GB MyBook through firewire
LeadTek WinFast PVR2000 TV Tuner
Windows Vista Home Premium SP1 32 bit
HEC Winpower 550AB
I was watching this board for a few days now but I haven't had seen any post with a similar problem. I've already tried bios 1.1, 1.2 and the beta bios 1.22. What happens is when I run a game, it will close a few minutes later and Vista will show a "nvlddmkm stopped responding" error. This happens with forceware version 175.19, 177.79 and 177.83. With forceware 169.25 though, I can play a game normally. If not for the specific driver version that works, I might have suspected it's a power supply problem. I was fine with using the older driver, but now that they released the new driver with Physx support, I want to update.
Someone in another forum said that he was able to make his 8800GT Sonic work with beta bios v. 1.24, but had problems with beta 1.23. I don't have the 1.24 bios to test yet to see if it'll fix the issue.
I'm aware of the 8800Gt having issues with older boards with PCI-E v1 but since this board has PCI-E 2.0, this should not be the case. I've also tried putting the card into the second PCI-E slot but encountered the same problem. The 6 pin power connector is properly connected to the video card, and I even tried connecting a 4 pin molex to the connector above the PCI-E slot (which I know is used as extra power for Crossfire configuration).
So.. anybody encountered this problem too? Any solutions (other than getting an ATI card).

Quote from: NovJoe on 20-August-08, 14:43:39
This is more of a driver issue with the OS rather than the board issue.
Normally, that would be my conclusion too, except that I did a few more tests:
8800GT + another computer on XP + forceware 175.19 = normal
8800GT + another computer on Vista + forceware 174.xx (driver that came with the CD) = normal
7600GT + P45 Platinum + forceware 175.19 = normal
8800GT + P45 Platinum + forceware 169.25 = normal
8800GT + p45 Platinum + forceware 174.xx/175.19/177.79/177.83 = "nvlddmkm stopped responding" error
What I'm asking from other users though is if they managed to use an 8xxx/9xxx series on this board with the latest drivers without encountering error on games, and what bios version they were using. The just-released official 1.3 bios even included a compatibility fix with the Geforce 9xxx series. Flashed mine yesterday but didn't solve my problem.

DDR3 Ram are compatible with MSI P45 Platinum motherboard

hello friends,
I want to ask question about MSI P45 Platinum motherboard. MSI P45 Platinum Motherboard support DDR3 Ram or not.
I am very confuse.

Read here for specs P45 Platinum.
http://global.msi.eu/index.php?func=prodmbspec&maincat_no=1&cat2_no=170&cat3_no=&prod_no=1479#menu
5th line from top, DDR2 800/1066/1200.
Like Henry mentioned, the P45D3 Platinum supports DDR3

Inappropriate Temperatures with P45 Platinum

Similar Messages

Maybe you are looking for