Inaudible sound from rear speak
hi,
i recently brought a soundblaster li've 24 bit sound card , and creative inspire 5. speakers. When i try to play dvds on powerdvd with prologic on, on power dvd software i can hardly hear any sound at all from my rear speakers. And also please explain what is the difference between software decoder prologic on power dvd and the hardware decoder ddts-00. will the surround quality be better on the ddts 00 decoder
NOOOO, wait. If you enable CMSS, you will get the same STEREO signal to all speakers. You will not get 5.. CMSS is for a 2 channel stereo signal to be sent to all speakers. Its mainly for music and not 5. DVDs.
EG: If you have a Divx movie which is 2 channel then you can turn on CMSS to get all speakers working, but this is not 5..
What you need to do is dissable CMSS.
Make sure everything is set to 5. also in windows control panel.
Now with WMP 0 you then need to go into the options for sound and also set it up to use 6 channels. This is 5..
You can also get WIN DVD as it will give you 5.
The best way to know what is going on is do this.
Play a movie with CMSS on, like you have it.
Now while playing the movie open up media CC. and then go to Surround mixer. Now go to advance and play with the sliders for all speakers. Lower the centre one to Zero. You will still hear vocals, This is not right. Lower the front and centre speakers and you will still hear all sound FX. This is not 5. my freind. Try it for your self and then you will see what I mean..
Similar Messages
-
4.1 Speaker Setup - No sound from rear speak
Opsys: Windows 2000 (just installed)
Card: Audigy 2 ZS Platinum
Software: Installed full sets of Creative software, everything runs
I'm trying to set up a 4. system where I'm using 2 set sets of stereo speakers plugged into line outs # and #2.
The problem is that I get sound only from line out #. All attempts at plugging the second set of speakers into the other line outs doesn't do anything for sound. I have switched the 2 sets around and they both work from lineout #.
The speaker calibration program only works for the front left and right speaker (i.e. no rear speaker output). I have tried more than just the 4. option, but none of them produce any sound to the rear speakers.
I have enabled EAX and CMSS, but this hasn't done any good. Still no sound from the rear speakers.
I checked the speaker set up and the volumes are midway for all speakers, both front and back.
Soooo. My guess is driver problems or maybe the 2 way stereo plug doesn't work with the 3 way plugs of line out #2 and #3.
Any ideas?
RickOkay, I get the stupid award for this one. I didn't notice that I was plugging my rear speakers into to the mic instead of the lineout 2. Well, in my defense, they are symetrically located around lineout and they do fit.
I would suggest people with sound issues to look at the other utilities. The one that helped was the Thx Setup console. This displays all info about the speakers, analog/digital settings, and even a picture showing the card plugs (that got the noodle thinking).
Also the Surround Mixer showed the correct configuration of the 4 speakers but without a sub hooked up. This fits my 2 stereo connections exactly.
Cheers. -
I just noticed there is no sound coming out of my rear speakers. I have the Creative SOUND BLASTER X-Fi Fatalty card and the Logitech z-5500 speakers. EAX is enabled and I have tried checking out control panel on XP. Anyone have an idea?
Here's a tip from something that I discovered. Not sure who/what resets the volumes, but for some reason Windows will set the volume for all channels OTHER THAN left/right to 0, effecti'vely muting them. The solution? Go to "Control Panel", "Sound and Audio Devices", click on "Speaker Voume..." in the bottom half, and make sure that all the sliders are at max or at least moving together. This was my problem when I lost center and rear speaker outputs despite all other testing showing no problem.
-
After Windows XP clean re-load and SB Live installation, getting no sound from rear speake
I had to re-load my Sound Blaster Li've! Value but now I don't have any sound from my rear speakers. I have set the SB settings for four speakers and my Sound and Audio setting is for Quadraphonic. I registered for auto SB updates but the system could not find any updates for my installation.
ThanksAfter reading some threads I come away with some ideas and thoughts. I haven't tried everything, and there are a lot of unhappy customers out there. Creative, take note. In today's competiti've markets, you must look at yourself from the customer's viewpoint. Right or wrong, you must stri've to delight your customers, and resolve issues. Read about "Six Sigma", this is the way business will be successful in the coming years.
-
ok, im using an audigy 2zs, previously all my speakers have been working fine however recently the rear speakers have stopped working. i have diaged the speakers they are working fine, i have uninstalled and reinstalled the creai've drivers and updated them. Also i noticed that my rear speakers wasnt producing any sound after using win dvd 6.
i have looked through the discussion forum and knowledge base but with no solution. judging by other users problems with loss of sound to rear speakers this seems to be a serious problem to which creative has no solution. anyway any help would be much appreciated. thanx.nickyt8 wrote:
ok, im using an audigy 2zs, previously all my speakers have been working fine however recently the rear speakers have stopped working. i have diaged the speakers they are working fine, i have uninstalled and reinstalled the creai've drivers and updated them. Also i noticed that my rear speakers wasnt producing any sound after using win dvd 6.
i have looked through the discussion forum and knowledge base but with no solution. judging by other users problems with loss of sound to rear speakers this seems to be a serious problem to which creative has no solution. anyway any help would be much appreciated. thanx.
Not sure if this help but have you try enabling CMSS in eax console? -
Please help.. after May Windows Updates no sound from rear speake
Hello!?My rear channels stopped working, I am thinking it might have happened because of the recent windows update. I have Audigy2 ZS Platinum Card and Logitech 5. speakers. Please help, I tried drivers from CD and the one on the website, no luck
I doubt if the recent windows updates has anything to do with your rear speakers. I have all the recent updates and my speakers are working fine. you could go the Add/Remove program and uninstall the updates. Then you would know for sure if that caused the problem.
Dell XPS 600 Intel Pent D 830 3.0ghz
Chipset- Nvidia nForce4 SLI Intel Edition
WD 60gb HD
2gb Ram
DVD-ROM
DVD-RW (Plextor 760A)
Creative XF-I Extreme Music
Logitech X-540 speakers
EVGA 7950GT
Dell 2007WFP (I-SPS panel)
Win XP SP2
BIOS A -
For those that point at the sticky topic, let me just say that I've already read it, implemented the suggestions there, and it has provided no result.
My setup is an Audigy 2 ZS card mated with Altec Lansing VS35 5. speakers. I've connected the cables correctly, enabled CMSS, updated my drivers to the latest version, but during Speaker Calibration, playing games, watching DVD movies, there is no output from the center speaker. If I watch encoded movies (avi files), I can hear sound from the center speaker. So what seems to be the problem? Anyone got any suggestions?Message Edited by mofo on 03-9-2005 08:0 AMI have the same problem, games and music etc all speakers work, but during the tests/calibration I get no sound from rear speakers, center or the sub...... help please! (from the firewire port out the plugs all go as follows: yellow, black, green)
-
Why no sound from rear speakers (Xfi X
Vista 32bit, CMSS enabled, why no sound from rear speakers with music? XP no problem at all, only in Vista. Using latest drivers (v2.5.0004).
I realize I'm hoping against hope to get a useful answer at the Creative forums, but I do believe in miracles and the odd one happening once or twice in a lifetime, lol.Well, I think I have an answer, from Catherina-CL's Audio in Windows Vista post. 2.The Vista audio architecture changes the way per-stream audio processing works, which required us to write new software to support this
Issues that may be encountered:
CMSS no longer works on audio streams from the OS.
Status:
Features based on Windows XP architecture must be rewritten to conform to the new Vista architecture, and we have a team of software engineers, project managers and testers dedicated to this task in order to provide our customers the same seamless audio experience under Windows Vista that they enjoyed under Windows XP. However, I found a somewhat crappy solution, at least with my old Altec Lansing 4 speaker/ subwoofer system. Unplug the surround cable from your subwoofer (unplugging it from the card itself has no effect). That at least will make all the speakers work, even if it's not true surround. Good for listening to music loud. -
Hi I have a problem with my iPhone 4S I have no sound from my speaker , keyboard, notifications. or volume controls, I have reset my iphone many times and still the same, any advise will be greatful
ThanksI don't think that a software update from Apple will solve the issues that you are having. You have a rogue installation. After you posted I have just done the following:
Disk Utility can verify my partitioned Volume (including my boot disk) AND REPAIR the non-boot disks on the same Volume without a glitch. It repairs the non-boot disks containing data smoothly.
I have used Mail to send some mails from some Yahoo and Hotmail accounts to my Thunderbird client containing GMail accounts - absolutely normal.
I have iLife '09 but my iMovie '09 and iPhoto '09 open in a jiffy and I see no issues here. I have 6GB RAM (Maximum) on an early 2008 Macbook Pro with a 750GB hard drive partitioned with 120GB reserved for the Boot Drive.
I am sorry that I cannot help further but I am sure there must be a way to reinstall the software without having to revert to restoring your ML backup. I have two clones and if you have such I would attempt to do that through that rather than through Time Machine - that is of course if you have a cloned drive.
Good luck! -
No Sound From Center Speaker [Win 7]
$No Sound From Center Speaker [Win 7]? Hi,
I downloaded the Darkest of Days demo and noticed that the speech volume was very low if i positioned it center of the camera. But if i positioned it on the left or right of the camera, the speech volume would increase. I found it strange.
I closed the game. And ran my speakers through window's speaker test. Every speaker responded with a sound. Unconvinced, i opened a few songs. That's when i noticed the center speaker wasn't producing a sound. Even on 5. content (movies & music) the center speaker wouldn't work.
**bleep**, no wonder those AC3 movies had low speech and i had to manually boost the speech volume. I noticed the low sound in games before too...but i attributed it to the 5. surround thing. Guess i was wrong!
System Rig:
Intel Core 2 Duo E6400 @3.2Ghz
Gigabyte P965-DS3
[color="DarkOrange">ATi HD4850
Twinmos 3xGB DDR2 800Mhz + GB OCZ 800 MHz
Zalman 9700
Creative Audigy2 ZS
Creative Fatalty Gaming Headset
250GB Seagate SATA-II 7200.0 8MB
Enermax 535W PSU
Logitech X-540 5. Speakers.Hi
Can you clarify that are getting the voice when you play the DVDs/CDs?If you are not getting the voice and you are getting the sounds only? Then there could be some connectivity issue for Center Speaker.Pl check the connections .. Regds Balu -
No sound from right speaker on Pavilion g6-1353ea after installing Windows 8
I've had no sound from right speaker on my HP Pavilion g6-1353ea after installing Windows 8. I've checked all drivers, and have done the sound test in sound properties (left speaker beeps fine, but then nothing from the right). Anyone else having this problem/found a solution?!
Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp59001-59500/sp59154.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, shut down the notebook, unplug the AC Adapter and then remove the battery. Hold down the Power button for 30 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio in both speakers.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
No sound from my speaker iphone 4S, headphones play normal, phone rings normal, alarm sound normal, re-installed software, will not play sound when music is played from speaker but speaker works for everything else....(phone ring and alarm)... no notification sound for text messages......
I checked all settings..... good...
confused???
please advise,it's a hardware issue read more about it here
https://discussions.apple.com/thread/1343532?start=315&tstart=0
more hits
https://www.google.dk/search?client=opera&q=4:3&sourceid=opera&ie=utf-8&oe=utf-8 &channel=suggest#client=opera&hs=UGk&channel=suggest&sclient=psy-ab&q=iphone+stu ck+in+headphone+mode&oq=iphone+stuc&gs_l=serp.3.3.0l4.412779.418971.0.420896.16. 9.2.5.5.0.86.545.9.9.0...0.0...1c.1.9.psy-ab.HHtp6aEcO5U&pbx=1&bav=on.2,or.r_cp. r_qf.&bvm=bv.45175338,d.bGE&fp=43d9a4347e8aaeda&biw=1535&bih=773 -
Soft sound from rear speakers while playing mov
Hi,?Gaming and music is done via all speakers (i'm using analogue connection) just fine, but when i play a movie (using powerdvd 6?deluxe) i get faint sounds from the rear speakers. I had contact with creative's help desk in my country and we ran thru all system settings (e.g. thnx console). Everything was configured correctly., tho still a weak sound from rear speakers. They could not help me further ?I'm using a x-fi fatality soundcard with a logitech z-5400 speakerset.
When running a movie it shows a logo near the system tray : dolby digital. I am hoping one of u has a solution to this problem. Greetz,?NaskIn most of the cases, movies with mutichannel soundtrack do not use constantly every speakers. I think your case is normal and that's only your DVD's mix (as many DVD) that concentrates more on the front. try some of the sample there: http://www.digital-digest.com/dvd/do...s/trailers.phpIf the first one sound at the same level for each speakers then it's alright.
-
LIVE 5.1 - NO SOUND FROM CENTRE SPEAKER - WIRES
NO SOUND FROM CENTRE SPEAKER ?WIRES & PLUGS SEEM OK !ANY IDEAS
plus I have switched around speakers & wires, so its not a speaker problemit must be the centre output ?could it be a hardware fault or software related
-
Sound from the speaker iPhone 4S 5.1.1. disappeared!?
About one hour ago I lost the sound from the speaker iPhone 4S 5.1.1. Lost in the middle of a conversation with a friend whom I put on speakerfon, first started to choking and after that sound is disappeared, and than appears in the fraction of a second and after is completely gone. On two occasions it choking when I put some videos and that's all. There is no sound even when someone call me, only vibrates. Note that phone was never dropped, as a new one, and I got it from July last year. Headphones works normaly. Any help without service?
Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
More Info Here > http://support.apple.com/kb/TS2802
Maybe you are looking for
-
How do I stop firefox from switching to new tab when opening bookmarks in new tab
When I open a link in a new tab it does not switch to it automatically. I had to reinstall firefox to stop it from switching to new tabs automatically since the option being unticked didn't stop it from happening anyway. Now only when I open a bookma
-
How to reorg my tables that being updated very frequently during batch jobs
Hello All, See I have 4 tables of them 250+ Gb and rest 2 50+(<100) Gb in size. Now client is asking to reorg them. No I have two questions 1. When I should go for reorg.? 2. and how? Thanks in advance. Regards, Alok
-
PrintWriter not working !!
import java.io.*; public class FileDemo { public static void main(String args[]) { if (args.length != 1) { System.out.println("Must enter text to write to file"); return; try { PrintWri
-
GREP style as part of paragraph style
I'm wanting to create a GREP style that uses a character style. Whenever certain words (No class) appear followed by dates. Sometimes it is a single date and sometimes more than one date. For example: No class 7/11. No class 7/11-8/11. What I have so
-
EP7, UWL, want to remove Manage Substitution Rules + Personalization
Hi everyone Max points to the person who comes up with the workable answer!! Have upgraded from EP6 to EP7. Want to switch off personalize and manage substitution from the drop down list displayed in the main UWL view. Have looked at Content Admin =>