Inbound Calls Fail
HI.
I'm running CME on a 2851.
My issue is with inbound calls not failing totally, but then requiring the extension to be dialed. This only happens for calls where the calling number is unknown.
So all calls inbound work if the inbound calling number is known. Calls route nicely.
If the calling number is unknown the caller gets a tone, whereby they need to then dial the extension.
Ideally I'd like to have unknown calling numbers simply route the call the same way as with a known calling number.
FYI when i debug q931 caller id (if off) is shown as Calling Party Number i = 0x00A3, N/A
Appreciate any help as this is causing some problems!!!
Configuration attached
Timothy,
When the calls come in, a dial-peer match is made, and in this case, where the calling number is known, the dial-peer whose destination-pattern command matches the calling number is selected, and the call is routed.
For calls where the calling number is not available, there is no dial-peer matched, so the default dial-peer (dial-peer 0) is used, and two stage dialing is then required.
To resolve, a quick solution would be to create a new dial-peer that has the incoming called-number command (which matches on the called number), so that this dial-peer will always be used for all incoming calls regardless of whether the calling number is available or not.
Use the direct-inward-dial command as well in this dial-peer to force one stage dialing.
dial-peer voice 90 pots
incoming called-number .
direct-inward-dial
port 0/0/0:15.
See also
* http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml#topic3
* http://www.cisco.com/en/US/tech/tk652/tk698/technologies_tech_note09186a00800e00d0.shtml
Hope this helps.
Regards,
Michael.
Similar Messages
-
Inbound calls to response group - failed
Hi!
I have a problem with inbound calls to Response group from external phones. But calls from Lync client to Response Group are working without problem. And calls from external phones to Lync users perfectly working too.
I found this alert in event viewer
Event 31172 LS response group service
The workflow runtime encountered an error while connecting the call.
The workflow runtime encountered a critical error.
Failure occurrences: 2, since 27/06/2013 9:20:18 PM.
The last encountered error was from a workflow having the display name: Group2, the URI: sip:[email protected], and
the GUID: 12ee27bf-15ab-4cc9-8265-57a08f17ac5b.
Exception: Microsoft.Rtc.Signaling.OperationTimeoutException - This operation has timed out.
Inner Exception: -
I hope for your help!!! Thanks!!Hi,
Here is a similar case for your reference. Try to remove NAT and have the SIP line connect direct to Lync Server.
http://social.technet.microsoft.com/Forums/lync/en-US/d0e53ab2-42e7-4d79-be01-b8770d508133/calls-to-workflows-fail
Kent Huang
TechNet Community Support -
Lync 2011 for Mac with iMessage on OSX inbound and outbound calls fail
Running Office 14.4.9 updates and many before that. If you activate or deactivate an iMessage account using the built-in Messages application, Lync can no longer make or receive calls. Calls received will automatically go to voicemail.
Outbound calls just ring and ring. The phone setting in Lync were all three set to Lync as well.
The only way I've found them to work is to following the first instructions at the following link:
https://support.microsoft.com/en-us/kb/kbview/2691870?wa=wsignin1.0
Log on to your computer by using administrative credentials.
Exit Lync if it's running.
Drag the Lync application to the Trash.
To remove your existing Lync preferences, delete the following files:
Users/username/Library/Preferences/com.microsoft.Lync.plist
Users/username/Library/Preferences/ByHost/MicrosoftLyncRegistrationDB.xxxx.plist
Users/username/Library/Logs/Microsoft-Lync-x.log
If you activate or deactivate an iMessage account steps 1-4 must be performed, otherwise, phone calls fail. One additional annoyance I've noticed is that Lync tends to hand with a red X on the icon in the dock when this happens as well. You must
use the terminal and do 'pkill Lync' in order to close it.Hi MSGuest,
Can you install the latest update and then check again ?
https://www.microsoft.com/en-us/download/details.aspx?id=36517
Best regards,
Eric
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
CME 7.1 with SCCP 7940G phones and SIP connection to a VOIP provider - inbound outbound fails
Here's a quick and dirty diagram of a CME 7.1 configuration. The phone can all call each other but something is not quite right with the SIP provider. The registrar and SIP registration pieces are working but most of the configuration examples that I've seen make me think that the CME router was being used as the edge device to the internet. From my drawing, you can see that is not the case here. My edge device is a Cisco ASA5505 with 9.2.x software running. I might be missing something in the SIP gateway knowledge department. Without diving into the configuration, I'm wondering if SIP messages are failing for calls because of NAT'ing? Trying to do searches has been tricky because I keep running into information that is more about setting up CME for SIP phones or just getting SIP to work between CME and a SIP provider. I have that part working. I'm just a bit unsure about how an SCCP 7940G gets an outbound call or even gets one to come in.
When I dial from my cell phone to the pilot number, there are no rings, it just goes to the VOIP provider's voice mail. When I try to dial out, I get a fast busy.
So, is NAT a consideration? Will the SIP gateway set up a call (forward) via the pre-established SIP connection? Yeah, I do sound like a newb.
If anyone has good information about, let's say, an inbound call and how that traffic flow works.
Thanks!Have you configured your ASA to either NAT the IP address of the CME router or to do port forwarding for port 5060?
-
I'm replicating between two servers in two sites (Server A - Server 2012 R2 STD, Server B - Server 2008 R2) over a VPN (Sonicwall Firewall). Though the initial replication seems to be
happening it is very slow (the folder in question is less than 3GB). I'm seeing these in the event viewer every few minutes:
The DFS Replication service is stopping communication with partner PPIFTC for replication group FTC due to an error. The service will retry the connection periodically.
Additional Information:
Error: 1726 (The remote procedure call failed.)
and then....
The DFS Replication service successfully established an inbound connection with partner PPIFTC for replication group FTC.
Here are all my troubleshooting steps (keep in mind that our VPN is going through a SonicWall <--I increased the TCP timeout to 24 hours):
-Increased TCP Timeout to 24 hours
-Added the following values on both sending and receiving members and rebooted server
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
Value =DisableTaskOffload
Type = DWORD
Data = 1
Value =EnableTCPChimney
Type = DWORD
Data = 0
Value =EnableTCPA
Type = DWORD
Data = 0
Value =EnableRSS
Type = DWORD
Data = 0
---------------------------------more troubleshooting--------------------------
-Disabled AntiVirus on both members
-Made sure DFSR TCP ports 135 & 5722 are open
-Installed all hotfixes for 2008 R2 (http://support.microsoft.com/kb/968429) and rebooted
-Ran NETSTAT –ANOBP TCP and the DFS executable results are listed below:
Sending Member:
[DFSRs.exe]
TCP 10.x.x.x:53 0.0.0.0:0
LISTENING 1692
[DFSRs.exe]
TCP 10.x.x.x:54669
10.x.x.x:5722 TIME_WAIT 0
TCP 10.x.x.x:54673
10.x.x.x:5722 ESTABLISHED 1656
[DFSRs.exe]
TCP 10.x.x.x:64773
10.x.x.x:389 ESTABLISHED 1692
[DFSRs.exe]
TCP 10.x.x.x:64787
10.x.x.x:389 ESTABLISHED 1656
[DFSRs.exe]
TCP 10.x.x.x:64795
10.x.x.x:389 ESTABLISHED 2104
Receiving Member:
[DFSRs.exe]
TCP 10.x.x.x:56683
10.x.x.x:389 ESTABLISHED 7472
[DFSRs.exe]
TCP 10.x.x.x:57625
10.x.x.x:54886 ESTABLISHED 2808
[DFSRs.exe]
TCP 10.x.x.x:61759
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61760
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61763
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61764
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61770
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61771
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61774
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61775
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61776
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61777
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61778
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61779
10.x.x.x:57625 TIME_WAIT 0
TCP 10.x.x.x:61784
10.x.x.x:52757 ESTABLISHED 7472
[DFSRs.exe]
TCP 10.x.x.x:63661
10.x.x.x:63781 ESTABLISHED 4880
------------------------------more troubleshooting--------------------------
-Increased Staging to 32GB
-Opened the ADSIedit.msc console to verify the "Authenticated Users" is set with the default READ permission on the following object:
a. The computer object of the DFS server
b. The DFSR-LocalSettings object under the DFS server computer object
-Ran
ping <var>10.x.x.x</var> -f -l 1472 and got replies back from both servers
-AD replication is successful on all partners
-Nslookup is working so DNS is working
-Updated NIC drivers on both servers
- I ran the following to set the Primary Member:
dfsradmin Membership Set /RGName:<replication group name> /RFName:<replicated folder name> /MemName:<primary member> /IsPrimary:True
Then Dfsrdiag Pollad /Member:<member name>
I'm seeing these errors in the dfsr logs:
20141014 19:28:17.746 9116 SRTR 957 [WARN] SERVER_EstablishSession Failed to establish a replicated folder session. connId:{45C8C309-4EDD-459A-A0BB-4C5FACD97D44} csId:{7AC7917F-F96F-411B-A4D8-6BB303B3C813}
Error:
+ [Error:9051(0x235b) UpstreamTransport::EstablishSession upstreamtransport.cpp:808 9116 C The content set is not ready]
+ [Error:9051(0x235b) OutConnection::EstablishSession outconnection.cpp:532 9116 C The content set is not ready]
+ [Error:9051(0x235b) OutConnection::EstablishSession outconnection.cpp:471 9116 C The content set is not ready]
---------------------------------------more troubleshooting-----------------------------
I've done a lot of research on the Internet and most of it is pointing to the same stuff I've tried. Does anyone have any other suggestions? Maybe I need to look somewhere
else on the server side or firewall side?
I tried replicating from a 2012 R2 server to another 2012 server and am getting the same events in the event log so maybe it's not a server issue.
Some other things I'm wondering:
-Could it be the speed of the NICs? Server A is a 2012 Server that has Hyper-V installed. NIC teaming was initially setup and since Hyper-V is installed the NIC is a "vEthernet
(Microsoft Network Adapter Multiplexor Driver Virtual Switch) running at a speed of 10.0Gbps whereas Server B is running a single NIC at 1.0Gbps
-Could occasional ping timeout's cause the issue? From time to time I get a timeout but it's not as often as the events I'm seeing. I'm getting 53ms pings. The folder
is only 3 GB so it shouldn't take that long to replicate but it's been days. The schedule I have set for replication is mostly all day except for our backup times which start at 11pm-5am. Throughout the rest of the time I have it set anywhere from
4Mbps to 64 Kbps. Server A is on a 5mb circuit and Server B is on a 10mb circuit.I'm seeing the same errors, all servers are running 2008 R2 x64. Across multiple sites, VPN is steady and reliably.
185 events from 12:28:21 to 12:49:25
Events are for all five servers (one per office, five total offices, no two in the same city, across three states).
Events are not limited to one replication group. I have quite a few replication groups, so I don't know for sure but I'm running under the reasonable assumption that none are spared.
Reminder from original post (and also, yes, same for me), the error is: Error: 1726 (The remote procedure call failed.)
Some way to figure out what code triggers an Event ID 5014, and what code therein specifies an Error 1726, would extremely helpful. Trying random command line/registry changes on live servers is exceptionally unappealing.
Side note, 1726 is referenced here:
https://support.microsoft.com/kb/976442?wa=wsignin1.0
But it says, "This RPC connection problem may be caused by an unstable WAN connection." I don't believe this is the case for my system.
It also says...
For most RPC connection problems, the DFS Replication service will try to obtain the files again without logging a warning or an error in the DFS Replication log. You can capture the network trace to determine whether the cause of the problem is at the network
layer. To examine the TCP ports that the DFS Replication service is using on replication partners, run the following command in a
Command Prompt window:
NETSTAT –ANOBP TCP
This returns all open TCP connections. The connections in question are "DFSRs.exe", which the command won't let you filter for.
Instead, I used the NETSTAT command as advertised, dumping output to info.txt:
NETSTAT -ANOBP TCP >> X:\info.txt
Then I opened Excel and manually opened the .TXT for the open wizard. I chose fixed-width fields based on the first row for each result, and then added a column:
=IF(A3="Can not", "Can not obtain ownership information", IF(LEFT(A3,1) = "[", A3&B3&C3, ""))
Dragging this down through the entire file let me see that row (Row F) as the file name. Some anomalies were present but none impacted DFSrs.exe results.
Finally, you can sort/filter (I sorted because I like being able to see everything, should I choose to) to get just the results you need, with the partial rows removed from the result set, or bumped to the end.
My server had 125 connections open.
That is a staggering number of connections to review, and I feel like I'm looking for a needle in a haystack.
I'll see if I can find anything useful out, but a better solution would be most wonderful. -
Hi All,
Inbound proxy failed in ECC with below error Please help.
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIProxy</SAP:Category>
<SAP:Code area="ABAP">DYNAMIC_CALL_FAILURE</SAP:Code>
<SAP:P1>UNCAUGHT_EXCEPTION</SAP:P1>
<SAP:P2>ZCL_P2F_IS_AGILE_TO_SAP</SAP:P2>
<SAP:P3>P2F_IS_AGILE_TO_SAP</SAP:P3>
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Error during proxy processing An exception with the type CX_SY_OPEN_SQL_DB occurred, but was neither handled locally, nor declared in a RAISING clause The database returned a value containing an error</SAP:Stack>
<SAP:Retry>N</SAP:Retry>
</SAP:Error>
Chaitanya NaruHi Chaitanya,
Looks like the ABAP code failed during a call to DB. You would have to sit with ABAPer fot this to debug and see where exactly the exception is being raised. Set a debug point in Proxy code and debug the message. You can use sproxy to test this.
Regards,
Sanjeev. -
SIP Trunk Question - Outbound Calls Fail
Hi Folks,
I am using a Cisco 2821 as a router that will convert a SIP trunk to an E1 PRI. Si my setup is:
SIp-Trunk > 2821 Router > E1 port on 3900> CUCM
Inbound calls are working fine, but outbound are failing. I am starting to think its due to transcoding issue on the SIP-GW maybe (there is nothing configured on it for XCODE etc).
I think my configuration is fine as I am able to recieve calls inbound. Just outbound fail.
Here are the debugs from the SIP-GW:
"Debug CCSIP calls"
*Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x4BB4F194
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 1528xxxx
Called Number : 909
Source IP Address (Sig ): 172.29.x.xxx
Destn SIP Req Addr:Port : 10.200.7.157:5060
Destn SIP Resp Addr:Port : 10.200.7.157:5060
Destination Name : 10.200.7.157
*Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : No Codec
Negotiated Codec Bytes : 0
Nego. Codec payload : 255 (tx), 255 (rx)
Negotiated Dtmf-relay : 0
Dtmf-relay Payload : 0 (tx), 0 (rx)
Source IP Address (Media): 172.29.5.210
Source IP Port (Media): 16786
Destn IP Address (Media): -
Destn IP Port (Media): 0
Orig Destn IP Address:Port (Media): [ - ]:0
*Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC) : 28
Disconnect Cause (SIP) : 484
Can anyone shed some light on the area that I need to focus on? This is my first attempt at SIP and I am confused :)
Thanks.Hi
909 is what I meant to dial as that is the help desk for the telco.
I tried mobile numbers as well getting the same error codes. And international numbers.
If it's based on the called number being wrong then I guess I will have to play with the calling party ID and call type as well... Maybe this is causing it to fail?? -
CUVA calls fails because of gatekeeper bandwidth
My setup is CCM4.1, IOS GK and GWYs, IP Communicator with and without CUVA
A standard voice call using IP Communicator works fine. When CUVA is attached the call fails.
I discovered that removing the GK bandwidth statement allows the call to work, but the bandwidth statement is correct.
When the IP Communicator w/ CUVA initiates a call, the important parts of the setup are:
1) CCM requests (ARQ) 2048kbps bw from GK, confirmed.
2) CCM signals to GWY
3) GWY requests (ARQ) 2048kbps bw from GK, confirmed (this step is rejected when the GK bw statement is present).
4) GWY finds outbound POTS dialpeer, call setup continues
5) GWY changes bw to 128kbps (based on pots termination?)
6) Call is answered/completed.
Putting "bearer Speech" in the voice-port has no effect. The ARQ is sent before the outbound pots dialpeer is selected.
I can crank down the video quality as a workaround, but I would rather not do that.
Is there setting in CCM or on the inbound dialpeer that can make the gateway request the proper bw on the initial ARQ?Hi Christian, would you be so kind and send me your javac wrapper? I've developed my own (a quite simple c++ code) which helped me to deploy our application. But I must have forgotten about something because this wrapper fails while compiling jsp pages.
Thanks Jan -
cannot open pictures in Window 8.1...getting message 'the remote procedure call failed". What is the solution?
I recently bought a new HP computuer and uploaded Window 8.1. I then transfered photo files from old computer to new computer using a portable storage drive.
When trying to view the photos, a message pops up showing a file path...and the message 'the remote procedure call failed'. Photos are in jpeg format.
Please let me know what I can do to view photos?What program you use to view these photos? Choose another app to view these photos
for a test.
This issue only occurred when you view photo? What is the result if we connect the
portable storage drive to other computer (if possible)?
Run sfc/scannow to check and fix if there are some missing or corrupted system files.
Check the event viewer to see the detailed information of this issue.
Regards
Yolanda
TechNet Community Support -
Error during installation of ECC6- system call failed
Dear all,
i encounter the error as below during sap installation. its looks like the ID issue, but this id (fbqadm) is using by me to log into the windows. please help me.
thank
ERROR 2009-03-17 10:07:25.583 [syxxsyshlp.cpp:78]
syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage)
FSL-00001 System call failed. Error 1326 (Logon failure: unknown user name or bad password.
) in execution of system call 'LogonUser' with parameter (fbqadm, SAPFBWDEV01, *******, LOGON32_LOGON_INTERACTIVE,LOGON32_PROVIDER_DEFAULT,&hUserToken), line (1014) in file (synxccuren.cpp).
TRACE 2009-03-17 10:07:25.813 [iaxxejsbas.hpp:408]
handleException<ESyException>()
Converting exception into JS Exception ESyException.
TRACE 2009-03-17 10:07:25.813
Function setMessageIdOfExceptionMessage: modlib.jslib.caughtExceptionproblem fix after reboot the server
-
IPhone 4S Siri Will No Longer Voice Dial Contacts - Always Call Failed
I am not exactly sure when this started (5.0.1?), but when I ask Siri to dial someone in my contacts, Siri recognizes the request, proceeds to Dial the number and no matter which contact I try, I get an immediate "CALL FAILED" and then the iPhone immediately locks. I have restored the iPhone as new, Reset Network Settings, etc. to no avail. If I turn Siri off from Settings, the phone will revert to the previous Voice Control that was present in previous iPhones and Voice Calls are successful. Only when trying to use Siri do all voice initiated calls fail. And it is 100% consistent in the failure. This does not appear to be a Siri network issue, as all Siri other Siri requests work and are speedy. Co-workers with the 4S are also experiencing the same issue, so it does not appear to be specific to just my iPhone. Can anyone else confirm? Thanks.
OK, so i have tracked it down to a single AT&T Cell Tower location in my instance, but it also just so happens to be at my office, which means I am affected by it all day. What is happening is that at this particular location, the AT&T tower is misconfigured or experiencing some type of technical issue, resulting in the inability of the cell tower to handle simultaneous voice and data. Siri uses data to match the contacts, names etc and hands off to the Phone dialer, which immediately experiences a call failure as a result of the 3G Data still being in use by Siri. You can verify simultaneous voice and data connectivity by placing a voice call and then attempting to use 3G data (you must not be using WiFi to determine if this is a problem with the Cell network). While in a voice call, launch the Speedtest.net Mobile Speed Test app. You will clearly see that 3G data services have all but ceased if this is your problem. End the Voice Call and run the Speedtest.net Mobile Speed Test again and 3G data will work fine.
I have reported the problem via AT&T's Mark the Spot App numerous times and had my colleagues do the same and called AT&T Wireless customer service to no avail. They simply refuse to acknowledge the issue is on their end. I personally know at least 5 other iPhone 4S users in my office who are experiencing the same issue and the results can be consistently recreated on all of their devices. And again, once they leave the office in the afternoon, all of their services return to normal and they can again make and place Voice initiated phone calls without the dreaded Call Failed. Thanks AT&T. -
My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.
Hello SamSax
Check out the assist page below for troubleshooting call connectivity.
Calls and connection issues
http://www.apple.com/support/iphone/assistant/calls/
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
Dropped calls and "Call failed" on edge
My experience has been the opposite from others on the forum with the new 2.0.2 software. I can get 3G in town and I can place and receive calls just fine. At home, I only have an edge connection with usually 2-3 bars. 9 out of 10 calls I try to make from home fail. I get the three beeps and "Call failed" message on the screen. Usually it is a split second after I hit the call button. It's not even trying to make the call. I have restored it, restarted, etc. and it still happens! I cannot make a phone call at all. This is my business phone, and it is affecting my response to clients. Anyone have any suggestions? I will probably go to the genius bar tomorrow, but if I don't have to go through the hassle, I won't.
tigerarch,
Does this happen in all locations, or just your home?
What does the AT&T coverage map show for your home?
I live in a moderate area, and AT&T's disclaimer on the coverage map says that Good and Moderate may not have in building coverage. Not only does my iPhone sometimes not pick up a signal or complete calls, the same applies to other AT&T phones there.
My home is also made of stucco, which along with brick and cement block, is one of the worst materials for blocking signals.
If this only happens in one location, I would recommend contact AT&T and see if they will open a ticket. The probably won't open a ticket if your coverage is listed as "Moderate"
Hope this helps,
Nathan C. -
I have just bought my iphone 4S 32GB from three weeks ago and 'am facing a problem that in the middle of my calls it suddenly says call failed and it keeps on doing it every call i make .. I Don't know what to DO Please anyone help me i've got OS 5.0.1 and it's factory unlocked i've boughted from USA and it was sent to me where 'am living now in Egypt ...ANy Helpppppppppp Pleasee
try general>settings>reset>reset all settings and start up as an new phone.
-
I have a brand new iphone 4s unlocked version from singapore and I am experiencing constant network fluctuations on my iphone , no service, call failed, invalid sim, sim failure, bars fluctuating from 5 - 3 - 2 - 1, no signal/bars searching etc... Ifeel miserable after trying out all the options changed multiple sims, tried multiple carriers, restored the phone back and have set-up as new device but the problem does not get solved... its is so frustrating that after investing on a world's most expensive phone you cannot enjoy the calling features which the phone offers which is the main thing you own the phone for.. Rest of the things are working.. The funniest part I am not able to make calls or receive calls but can access the internet.. I have tried every possible thing and really very frustrated with this iphone of mine...I hope the problem gets solved.. would anyone have any solutions to this problem.. Does it mean one should never update software as I hear that after updating to IOS.5.1 the problem has started coming and same has been with there.... Apple says its a hardware failure which is very difficult to digest as sometimes I get 5 bars and able to make and receive calls but 95% of the time I am unable to. If anyone has any solution I will be very happy if he or share can share the same. Many thanks. its so disgusting to experience this on top of this apple does not support global warranty for the phone as you need to go to the country from where you bought the phone for replacement.. Truly sad state of affairs.. very very very dissappointing.
Have a look at this it might help
http://support.apple.com/kb/TS4148
Maybe you are looking for
-
i have deleted all contacts in icloud but still have them on my iphone (which is backed up as well to iTunes) how can i restore the iphone data to the iCloud so it will resend it to my mac book and iPad? I have switched my iphone to airplane mode so
-
What is the difference between direct and indirect method of cash flow in BCS.. How it is handled and best addressed in BCS.
-
Our desktop is really slowing down. Is there a way to "clean" it up or do we need to buy some sort of software?
-
i was uploading songs onto my ipod and when it was done i unplugged my usb cord and when i did that it keeps showing the apple icon. it wont do anything but flash the apple icon... is there anything that i can do to fix this?
-
Computer only plays one channel of audio
I use an HP Sleekbook 14 PC and recently it stopped playing out both channels of audio. I only get one channel. Any easy fixes?