Incomng and Outgoing calls are stop routing every five min
Dear Team,
Please find the attached running config and logs.Incoming and outgoing calls are landing on the gateway properly. But call stop working every five min.PRI is up and no error on controller E1.
Please advise how to identify the issue?
CUCM version 4.2
debug isdn q921
*Sep 2 08:48:21.874: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=2 nr=34
*Sep 2 08:48:21.890: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=3
*Sep 2 08:48:21.942: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=34 nr=3
*Sep 2 08:48:21.942: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=35
*Sep 2 08:48:27.866: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=35 nr=3
*Sep 2 08:48:27.866: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=36
*Sep 2 08:48:34.322: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=36 nr=3
*Sep 2 08:48:34.322: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=37
*Sep 2 08:48:34.326: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0503726912 N/A
*Sep 2 08:48:34.326: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=3 nr=37
*Sep 2 08:48:34.342: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=4
*Sep 2 08:48:39.694: %ISDN-6-DISCONNECT: Interface Serial0/0/1:29 disconnected from 0094777382372 , call lasted 181 seconds
*Sep 2 08:48:39.698: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=4 nr=37
*Sep 2 08:48:39.706: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=5
*Sep 2 08:48:39.730: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=37 nr=5
*Sep 2 08:48:39.730: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=38
*Sep 2 08:48:39.734: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=38
*Sep 2 08:48:39.746: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 voice-port 0/1/2
*Sep 2 08:48:49.746: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
*Sep 2 08:48:49.758: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nrsh
*Sep 2 08:48:59.762: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
*Sep 2 08:48:59.766: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nr
*Sep 2 08:49:01.946: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=38 nr=6
*Sep 2 08:49:01.950: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=39
*Sep 2 08:49:01.950: %ISDN-6-DISCONNECT: Interface Serial0/0/1:27 disconnected from 0503726912 , call lasted 27 seconds
Voice-Gw#
Voice-Gw#
Voice-Gw#
Voice-Gw#
*Sep 2 08:49:01.954: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=39
*Sep 2 08:49:01.962: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
*Sep 2 08:49:02.034: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=39 nr=7
*Sep 2 08:49:02.034: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=40
controller E1 0/0/1
pri-group timeslots 1-31
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
=======================
Voice-Gw#
*Sep 2 08:55:25.214: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=71 nr=27
*Sep 2 08:55:25.214: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=72
*Sep 2 08:55:25.234: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=27 nr=72
*Sep 2 08:55:25.246: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=28 nr=72
*Sep 2 08:55:25.250: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=28
*Sep 2 08:55:25.258: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=29
*Sep 2 08:55:27.518: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=72 nr=29
*Sep 2 08:55:27.518: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=73
*Sep 2 08:55:27.522: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=29 nr=73
*Sep 2 08:55:27.534: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=30
*Sep 2 08:55:27.546: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=73 nr=30
*Sep 2 08:55:27.546: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=74
*Sep 2 08:55:33.318: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=30 nr=74
*Sep 2 08:55:33.330: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=31
*Sep 2 08:55:33.390: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=74 nr=31
*Sep 2 08:55:33.394: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=75
*Sep 2 08:55:37.190: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=75 nr=31
*Sep 2 08:55:37.194: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=76
*Sep 2 08:55:38.534: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=76 nr=31
*Sep 2 08:55:38.534: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=77
*Sep 2 08:55:38.538: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0504312690 N/A
*Sep 2 08:55:38.538: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=31 nr=77
*Sep 2 08:55:38.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=32
*Sep 2 08:55:42.542: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=32 nr=77
*Sep 2 08:55:42.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=33
*Sep 2 08:55:42.606: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=77 nr=33
*Sep 2 08:55:42.606: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=78
*Sep 2 08:55:46.766: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=78 nr=3
% Invalid input detected at '^' marker.
Voice-Gw#sh controllers e1 0/0/1
E1 0/0/1 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20060711, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (99 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Voice-Gw#
Voice-Gw(config)#do sh isdn statu
Global ISDN Switchtype = primary-net5
ISDN Serial0/0/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x00000000
Number of L2 Discards = 0, L2 Session ID = 0
ISDN Serial0/0/1:15 interface
dsl 1, interface ISDN Switchtype = primary-net5
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
3 Active Layer 3 Call(s)
CCB:callid=E3C0, sapi=0, ces=0, B-chan=30, calltype=VOICE
CCB:callid=E3C6, sapi=0, ces=0, B-chan=31, calltype=VOICE
CCB:callid=E3CB, sapi=0, ces=0, B-chan=29, calltype=VOICE
Active dsl 1 CCBs = 3
The Free Channel Mask: 0x8FFF7FFF
Number of L2 Discards = 0, L2 Session ID = 2
Total Allocated ISDN CCBs = 3
Hi.
Can you please also attach a CUCM trace during a disconnected call?
Thanks
Regards
Carlo
Similar Messages
-
Ordinary outgoing calls are stopped in less than a second
I was extremely satisfied with my new I-phone 5S until I tryed to call a friend of mine. The call was stopped in less than a second. Rebooting and resetting have had no effect, I simply can´t use the phone! I have no problems recieving calls or using FaceTime. Any suggestions?
Knut Kvinnesland
NorwayThank you for your expedit answar, h.wilhite. I did, the SIM-card was okey and activated...they argued. Maybe I should just check the SIM-card in another cellphone?
-
3GS IPhone shuts off from incoming and outgoing calls 2 or 3 times a day
3GS IPhone shuts off from incoming and outgoing calls 2 or 3 times a day. The phone stays on but I can't call out or receive calls till I turn the phone off and back on.
I have the same problem with my 2 month old 3GS phone. It will shuts off from incoming and outgoing calls 2 - 3 times every day. I would miss important business calls. And will discover it only when I need to make a call. In this case screen looks normal. I choose contact, go to next screen - call in progress, it also looks normal, but there is no dial tone. Than I would restart the phone, and it will work again, displaying my missing calls, and angry voice messages of my customers, which trying to reach me. Please help us solve this problem (or maybe it is time to exchange my 3GS for a new one?)
-
i am having bugs with the ios 5, after it got the update it is unable to make outgoing calls. in-place the incoming and outgoing texts are working please help me asap...!
Sometimes and this is network dependant if they suspect the phone to be lost or stolen as in this case with change of Sim card and provider then the origonal network can and some will block the phone untill you have rang them and proven it's not the case or if you have bough this 2nd hand then the origonal seller may have stopped paying the contract bill and thus the phone is blocked
-
SIP trunk incoming and outgoing calls issue
Hi Everyone,
We recently installad a SIP trunk and terminated on CUBE and CUCM but we have issues on incoming and outgoing calls, When someone dial in from outside he keeps listening the dailing ring even after we pick up the phone and at the end the callers time exipres and call gets disconnected.
For Dailing out, the dialed number rings and caller hear the dailing ring as well but if someone pick the phone it apprears that call is connected but no audio in it, dead air.
Our call flow is as
IP Phones => CUCM --->SIPTRUNK--->CUBE=>SIPTRUNK=>SP
I have attached the config for CUBE and debug ccsip messages output for both incoming and outgoing calls.
Please if some help in sorting out this issue, Thanks in Advance
TasneemInbound call>>>>
The reason you are experiencing this is that your CUBE is requesting PRACK and your provider is not responding to it..
Here we have your cube sending 180 ringing with "Require 100rel"..This was sent several times and your ITSP didnt respond probably because they do not support 100rel...(It is Huwaei after all, they do what they like)
Sent:
SIP/2.0 180 Ringing
Via: SIP/2.0/UDP 10.205.20.50:5060;branch=z9hG4bKkpw18wp35hfw2c23h51ww6a8aT19871
From: ;tag=sbc080552fph4hp-CC-25
To: ;tag=256F3440-12C
Date: Thu, 16 Jan 2014 13:31:34 GMT
Call-ID: isbc6818c4kfhaa4ca1k5f8k1awsh52f1ccw@SoftX3000
CSeq: 1 INVITE
Require: 100rel
RSeq: 2507
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Remote-Party-ID: "TEST STC" ;party=called;screen=yes;privacy=off
Contact:
Record-Route:
Server: Cisco-SIPGateway/IOS-15.2.4.M2
Content-Length: 0
AFter the CUBE didnt get any response, it then replied with Gateway Timeout...
Jan 16 13:31:54.550: //31880/5A4406E48184/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 504 Gateway Timeout
Via: SIP/2.0/UDP 10.205.20.50:5060;branch=z9hG4bKkpw18wp35hfw2c23h51ww6a8aT19871
From: ;tag=sbc080552fph4hp-CC-25
To: ;tag=256F3440-12C
Call-ID: isbc6818c4kfhaa4ca1k5f8k1awsh52f1ccw@SoftX3000
CSeq: 1 INVITE
Reason: Q.850;cause=102
Content-Length: 0
I suggest you disable this parameter..and test again
voice service voip
sip
rel1xx disable
Please rate all useful posts
"The essence of christianity is not the enthronement but the obliteration of self --William Barclay" -
I Just bought a second hand iPhone 4S I am having issues with the hearing during incoming and outgoing calls, I have turned the volume up and checked my settings but I still have trouble hearing the other person speak. It works if it's on speaker or if I have headphones plugged in. I need help desperately!!!!! Any suggestions on what to do???
Hey Itsanaasaunders,
Thanks for the question. I understand that you are experiencing issues hearing sound while on a call (receiver wise, not speakerphone). The following resource provides troubleshooting steps for this symptom:
If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone - Apple Support
http://support.apple.com/en-us/HT203800
Clear the receiver
The iPhone receiver won't work properly if it's blocked or dirty. Here's where the receiver is:
Follow these steps, testing after each:
- Make sure nothing is blocking the receiver, such as a case or film.
If you have a new iPhone, remove the plastic film on the front and back of the device.
- Check the receiver opening to see if it's blocked or dirty. If necessary, clean the receiver opening with a clean, small, dry, soft-bristled brush.
- While you're on a call, turn on speakerphone. If you still can't hear, then your network or reception could be the issue. Try calling again later or from a different location.
Restart and update
1. Restart your iPhone and test again.
2. If there's still no sound or poor sound quality, update to the latest version of iOS.
Get more help
If you've tried these steps and there's still no sound or poor sound quality from your iPhone, contact Apple Support.
Thanks,
Matt M. -
Turn off verizon greeting with incomming and outgoing calls for LG G2
Can anyone tell me how to turn off the Verizon greeting with all incoming and outgoing calls for LG G2
Hi lindapet2!
I would love to assist you with your device settings. First, provide me some additional details as to what you're experiencing. Are you referring to an audible alert or is this a pop-up message you see when making and receiving calls? Please let me know so that I can further assist. Thanks!
AnthonyTa_VZW
Follow us on Twitter @VZWSupport -
My outgoing calls are blocked from Southern Ireland how to unblock
My outgoing calls are blocked from irelandneed to unblock them
Hi ,
Welcome to the community.
What phone are you using?
What network are you on EE/T-Mobile/Orange?
And last question are you on contract?
If you could reply with this, I will try andf get you sorted to make calls in Ireland .
Thank you. -
Hi Everyone, I am using iPhone5, my question in how to display name and contact number both stored for incoming and outgoing calls? If I have saved five different numbers with a same name, how do I recognise that from which number caller is calling?
I have friends all over Europe, does it matter what number they use to call me? Nope! All incoming calls are free for me.
The only time you ever have to worry about which number is if you get charged for incoming domestic/international calls.
You can tag their number (work/home/iphone) and that may show on the CallerID accordingly.
It should show, John Doe
underneath, work/home/mobile
For example:
http://shawnblanc.net/images/img-0009-1.png -
IPhone 5s call signal strength is 3 bars and my calls are breaking up?
I switched from an iPhone 4s to an iPhone 5s and now my iPhone signal strength is 3 bars and my calls are breaking up? what gives?
I live on top of a hill in a major metropolitan city and my carrier has always been Verizon and my call signal strength has always been 5 bars and occassionally on a cloudy rainy day I had 4 bars. Since upgrading to the 5s my call signal strength at my home has never gone past 3 bars even when Wi-Fi is connected. When W-Fi is turned off and LTE service kicks in, the call signal strength flutters between 2-3 bars and if I am on a call, the person on the other end is telling me I am breaking up. This has never happened with my iPhone 4, my iPhone 4s. Is anyone else noticing signal problems?I am also having the same exact issue. I had an iPhone 4S with Sprint servince and always had at least 4 bars of service (4 dots after iOS7 upgrade) and I am now fluctuating between 1 and 2 dots on my new iPhone 5S. I am also having people I am on the phone with tell me that I sound like I'm in a tunnel and or that I am breaking up. I am also hearing the breakup of voice service even when speaking to someone on a landline. I took my first iPhone 5S back to the store and traded it in for a new one and am having the same exact problem with this new 5S phone. I was told by the salesman at the store that the problem was due to the 5S is using different towers than the 4S and that the new towers for the 5S were still being implemented. Do I know this to be true or necesarily believe this? No. Do I hope it's true or that Apple will come up with a fix for this problem in the very, very near future? Yes. Apple, what is going on with my service? It's obvious that it's happening to users from all of the major American networks.
-
I did the software update ios 7 and now i cant hardly get wifi and my calls are being dropped.Can anyone help me?
I updated my ipad to the ios7.4 and my wifi connection just wouldn't work any longer.
-
I need a app which can record incoming and outgoing calls automatically without internet
i need a app which can record incoming and outgoing calls automatically without internet.
Can some help me on this ?As far as I know there is no app to record phonecalls because US regulations, but I am not using iphone in US so we definately need call recorder. HTC or Samsung has call recorder so why we dont?
-
Missed calls and placed calls are not saving in 7942 phone
HI
i am facing some issue in telephone directory, in my phone missed calls and placed calls are not saving. i am using cisco call manager and 7942 phone. please help me in this issue.
Thanks
ShijoHi Shijo,
Is this affecting only one 7942 IP phone or all of them? if this is affecting all then you may try ta firmware upgrade. If this is only affecting one of them then you can compare the settings of this phone with the working ones or try setting the phone to factory defaults.
HTH
Manish -
No privacy settings to control incoming and outgoing calls
Is it possible to restrict incoming calls on the Droid Razr Maxx? With other Motorola phones (Droid X) it's easy to restrict incoming (and outgoing) calls to the address book only. .just can't find one.....thank you
You should be able too Have you Checked the Online Manual.?
-
My husband and I have separate phone numbers for our business but need to keep track of incoming and outgoing calls; however, by end of day many numbers have been automatically erased from our phone. How can we find those deleted numbers?
I believe the total amount is 100 calls that will list.
No way of changing that.
Maybe you are looking for
-
My Reminder app won't open In ipad mini 2. It worked for a few days but later on it didn't work anymore! tried rebooting and updating it but it still wont open. When I try opening it, it crashes. What do I doooo? Please help me.
-
Hi, I would like to know what suffix I need to put on my movie file so that I can use it in iMovie or iDVD. The movie file has .avi on it and can be read on Windows Media Player but I cannot get it into a file on the MacBook Pro such as iPhoto or iM
-
When i run quickime it just comes up with an error message saying "Error46: Could not load or find QuickTine ActiveX control". I tryed Uninstalling it and then reinstalling it but it still does it. Im am running Vista 32bit
-
Reg: XI - Message Monitoring
Hi! Gurus, This is Amar Srinivas Eli.I am workig on Production Support project. Here I got one issue related to Message Monitoring. Actually user send one information from Store Front Site to P31 R3 system via XI means XI Production System right
-
The client has his AD and Exchange 2010 on premise and would like to integrate with Office 365 SharePoint. I know it is possible to integrate SharePoint On premise to Exchange Online but how possible and what is required to create it in the opposite